This patch removes bad language in the comments in iwl-agn-rs.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes regression in iwlwifi IBSS rate scaling caused by the
patch named "mac80211: eliminate IBSS warning in rate_lowest_index()"
by Vladimir Koutny <vlado@work.ksp.sk>.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch aligns definition of host command with the spec. The
inaccuracies weren't critical though.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch disables power save upon association and enables it back
after association. This allows to associate to AP on a radar channel
if power save is enabled.
Radar and passive channels are not allowed for TX (required for association)
unless RX is received but PS may close the radio and no RX will be received
effectively failing association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up pci registers handling.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes handling of strcit_strtoul return value
"0 == sucess".
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows variable number of init calibrations and allows
addition new HW.
This patch also fixes critical bug. Only last calibration result
was applied. On reception of one calibration result all the calibration
was freed.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes the warning since registers might be accessed also
during rfkill.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces readl and writel with more cross platform ioread32
and iowrite32.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes use of strict_srtoul in sysfs code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945_get_active_dwell_time is called twice within the same context.
The patch removes one instance.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes bg_post_associate work. A direct call
iwl3945_post_associate is made to avoid the waiting by
userspace programs.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let mac80211 and bss_info_changed callback handle the association and
beacon changes.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes unlocking of mutex from post_associate.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes use of mac80211 defaults for channel and band.
Older code that uses G band channel 6 was removed. This patch also
changes iwl_set_rxon_channel signature.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows consecutive scans requests when driver is in
unassociated state.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unused forward declarations functions.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwl_mac_hw_scan handler.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch hopefully contains all necessary changes to support
firmwares for all devices up to atleast 2.13.3.0.
(or: LowerMAC Protocol Rev: 5.5 )
And this is a big win, since:
* newer firmwares are more stable and reliable than the old ones.
* no problems anymore with packages > 1399 octets (without lowering the MTU).
* monitor mode finally works on USB for more than just a few seconds.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
p54_set_filter has a way too many unnecessary "magic" parameters and values.
This patch axes all superfluous parameters and gives most of the magic values appropriate names.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace a hardcoded Analog switch (which breaks on N-PHY) by a call to
the switch_analog PHY operation.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the Analog switching code into the PHY files.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch provides a mechanism for platforms to be able to supply the
LED configuration via platform data, rather than having to hard code
it in smc91x.h.
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix regression tracked as http://bugzilla.kernel.org/show_bug.cgi?id=11361
and caused by commit f735a2a1a4 ("[netdrvr]
forcedeth: setup wake-on-lan before shutting down") that makes network
adapters integrated into the NVidia MCP55 chipsets fail to work in kexeced
kernels. The problem appears to be that if the adapter is put into D3_hot
during ->shutdown(), it cannot be brought back into D0 after kexec (ref.
http://marc.info/?l=linux-kernel&m=121900062814967&w=4). Therefore, only
put forcedeth into D3 during ->shutdown() if the system is to be powered
off.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the necessary changes to support LM87 firmwares.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k uses LED classdev functions, so it needs to either select or depend
on them. This patch uses the same selects that ath5k uses...
drivers/built-in.o: In function `ath_unregister_led':
main.c:(.text+0x138c1d): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `ath_register_led':
main.c:(.text+0x139c16): undefined reference to `led_classdev_register'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Jouni Malinen <jmalinen@atheros.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This splits the PHY allocation from the PHY init.
This is needed in order to properly support Analog handling.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both p54pci and p54usb uses a good chunk of device specific code to
get the data from the device's eeprom into the drivers memory.
So, this patch reduces the code size and will it make life easier if
someone wants to implement ethtool eeprom dumping features.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch greatly reduces one of biggest memory waste in the driver.
The firmware headers provides the right values for extra head-/tailroom
and mtu size which are usually much lower than the old hardcoded ones.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm afraid, I forgot to add the following lines to
7262d59366 ("p54pci: rx tasklet refactoring").
These changes are necessary to ensure loop termination.
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds read/write phyops for the LP-PHY and LP-PHY radios.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds template code for the LP-PHY.
No actual functionality is implemented.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sourcecode files for PHY code are named by phy_XXX.{c,h}
where XXX is the PHY type.
Move the N-PHY code to match the other files.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the remaining code from phy.c to phy_a.c
phy.c is removed.
No functional change. Just moving code and removing dead code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* No code changes...
* Split hw.c to multiple files for better maintenance and add some documentation on each file
code is going to grow soon (eeprom.c for example is going to get much stuff currently developed
on ath_info) so it's better this way.
* Rename following functions to maintain naming scheme:
ah_setup_xtx_desc -> ah_setup_mrr_tx_desc
(Because xtx doesn't say much, it's actually
a multi-rate-retry tx descriptor)
ath5k_hw_put_tx/rx_buf - > ath5k_hw_set_tx/rxdp
ath5k_hw_get_tx/rx_buf -> ath5k_hw_get_tx/rxdp
(We don't put any "buf" we set descriptor pointers on hw)
ath5k_hw_tx_start -> ath5k_hw_start_tx_dma
ath5k_hw_start_rx -> ath5k_hw_start_rx_dma
ath5k_hw_stop_pcu_recv -> ath5k_hw_stop_rx_pcu
(It's easier this way to identify them, we also
have ath5k_hw_start_rx_pcu which completes the
set)
ath5k_hw_set_intr -> ath5k_hw_set_imr
(As in get_isr we set imr here, not "intr")
* Move ath5k_hw_setup_rx_desc on ah->ah_setup_rx_desc so we can
include support for different rx descriptors in the future
* Further cleanups so that checkpatch doesn't complain
(only some > 80 col warnings for eeprom.h and reg.h as usual
due to comments)
Tested on 5211 and 5213 cards and works ok.
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is valid to pass &gphy->rfatt and &gphy->bbatt as rfatt and bbatt
pointer arguments to the function. So we have to use memmove for the
possibly overlapping memory areas.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As all the infrastructure for multiple transmit queues already exists
in the driver, this patch is entirely trivial.
The individual transmit queues are still serialised by the driver's
per-port private spinlock, but that will disappear (i.e. be replaced
by the per-subqueue ->_xmit_lock) in a subsequent patch.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Delete a couple of unused and uninteresting interrupt source mask bits:
- The receive resource underrun interrupt sources are uninteresting
because if we are in out-of-memory mode, we are already dealing with
the issue, and we don't need the hardware to remind us again that we
are out of memory.
- The LINK and PHY interrupt sources can be coalesced into one define,
since we always use them together.
- The transmit resource underrun interrupt source can be disabled since
we never activate the head descriptor of a paged skb until the
fragments are all activated, so transmit underrun during a packet
should never happen.
- The INT_EXT_TX_0 define is never used.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
There is no need to call netif_{stop,wake}_queue() when the link goes
down/up, as the networking already takes care of this internally.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Currently, there are two different fields in the
mv643xx_eth_platform_data struct that together describe the PHY
address -- one field (phy_addr) has the address of the PHY, but if
that address is zero, a second field (force_phy_addr) needs to be
set to distinguish the actual address zero from a zero due to not
having filled in the PHY address explicitly (which should mean
'use the default PHY address').
If we are a bit smarter about the encoding of the phy_addr field,
we can avoid the need for a second field -- this patch does that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Which top-level unit's SMI interface to use should be a property of
the top-level unit, not of the individual ports. This patch moves the
->shared_smi pointer from the per-port platform data to the global
platform data.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Simplify receive and transmit queue handling by requiring the set
of queue numbers to be contiguous starting from zero.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Get rid of the mv643xx_eth-internal MV643XX_ETH_CHECKSUM_OFFLOAD_TX
compile-time option. Using transmit checksumming is the sane default,
and anyone wanting to disable it should use ethtool(8) instead of
recompiling their kernels.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
By having the receive out-of-memory handling timer schedule the napi
poll handler and then doing oom processing from the napi poll handler,
all code that touches receive state moves to napi context, letting us
get rid of all explicit locking in the receive paths since the only
mutual exclusion we need anymore at that point is protection against
reentering ourselves, which is provided by napi synchronisation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Make napi unconditional on the receive side, so that we can get rid
of all the locking and local interrupt disabling in the receive path.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
If the platform code has passed us the IRQ number of the mv643xx_eth
top-level error interrupt, use the error interrupt to wait for SMI
access completion instead of polling the SMI busy bit, since SMI bus
accesses can take up to tens of milliseconds.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Since commit 81600eea98 ("mv643xx_eth:
use auto phy polling for configuring (R)(G)MII interface"),
mv643xx_eth no longer does SMI accesses from interrupt context. The
only other callers that do SMI accesses all do them from process
context, which means we can switch the PHY lock from a spinlock to a
mutex, and get rid of the extra locking in some ethtool methods.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
