commit 1ae948fa4f upstream.
This fixes a potential race condition observed on Power systems.
Several places throughout the aacraid driver call aac_fib_send or
similar to send a command to the aacraid adapter, then check the return
code to determine if the command was actually sent to the adapter, then
update the phase field in the scsi command scratch pad area to track
that the firmware now owns this command. However, there is nothing that
ensures that by the time the aac_fib_send function returns and we go to
write to the scsi command, that the command hasn't already completed and
the scsi command has been freed. This was causing random crashes in the
TCP stack which was tracked down to be caused by memory that had been a
struct request + scsi_cmnd being now used for an skbuff. Memory
poisoning was enabled in the kernel to debug this which showed that the
last owner of the memory that had been freed was aacraid and that it was
a struct request. The memory that was corrupted was the exact data
pattern of AAC_OWNER_FIRMWARE and it was at the same offset that aacraid
writes, which is scsicmd->SCp.phase. The patch below resolves this
issue.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fa2d9d6e89 upstream.
The > here should be >= or we end up reading one element beyond the end
of the qedi->itt_map[] array. The qedi->itt_map[] array is allocated in
qedi_alloc_itt().
Fixes: ace7f46ba5 ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d4a3d0a2f upstream.
Complements debugging aspects of the otherwise functionally complete
v3.17 commit 9cb78c16f5 ("scsi: use 64-bit LUNs").
While I don't have access to a target exporting 3 or 4 level LUNs,
I did test it by explicitly attaching a non-existent fake 4 level LUN
by means of zfcp sysfs attribute "unit_add".
In order to see corresponding trace records of otherwise successful
events, we had to increase the trace level of area SCSI and HBA to 6.
$ echo 6 > /sys/kernel/debug/s390dbf/zfcp_0.0.1880_scsi/level
$ echo 6 > /sys/kernel/debug/s390dbf/zfcp_0.0.1880_hba/level
$ echo 0x4011402240334044 > \
/sys/bus/ccw/drivers/zfcp/0.0.1880/0x50050763031bd327/unit_add
Example output formatted by an updated zfcpdbf from the s390-tools
package interspersed with kernel messages at scsi_logging_level=4605:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : scsla_1
LUN : 0x4011402240334044
WWPN : 0x50050763031bd327
D_ID : 0x00......
Adapter status : 0x5400050b
Port status : 0x54000001
LUN status : 0x41000000
Ready count : 0x00000001
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY pass 1 length 36
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY successful with code 0x0
Timestamp : ...
Area : HBA
Subarea : 00
Level : 6
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : fs_norm
Request ID : 0x<inquiry2-req-id>
Request status : 0x00000010
FSF cmnd : 0x00000001
FSF sequence no: 0x...
FSF issued : ...
FSF stat : 0x00000000
FSF stat qual : 00000000 00000000 00000000 00000000
Prot stat : 0x00000001
Prot stat qual : ........ ........ 00000000 00000000
Port handle : 0x...
LUN handle : 0x...
|
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 6
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : rsl_nor
Request ID : 0x<inquiry2-req-id>
SCSI ID : 0x00000000
SCSI LUN : 0x40224011
SCSI LUN high : 0x40444033 <=======================
SCSI result : 0x00000000
SCSI retries : 0x00
SCSI allowed : 0x03
SCSI scribble : 0x<inquiry2-req-id>
SCSI opcode : 12000000 a4000000 00000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000000 00000000
00000000 00000000
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY pass 2 length 164
scsi 2:0:0:4630896905707208721: scsi scan: INQUIRY successful with code 0x0
scsi 2:0:0:4630896905707208721: scsi scan: peripheral device type of 31, \
no device added
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 9cb78c16f5 ("scsi: use 64-bit LUNs")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fdb7cee3b9 upstream.
At the default trace level, we only trace unsuccessful events including
FSF responses.
zfcp_dbf_hba_fsf_response() only used protocol status and FSF status to
decide on an unsuccessful response. However, this is only one of multiple
possible sources determining a failed struct zfcp_fsf_req.
An FSF request can also "fail" if its response runs into an ERP timeout
or if it gets dismissed because a higher level recovery was triggered
[trace tags "erscf_1" or "erscf_2" in zfcp_erp_strategy_check_fsfreq()].
FSF requests with ERP timeout are:
FSF_QTCB_EXCHANGE_CONFIG_DATA, FSF_QTCB_EXCHANGE_PORT_DATA,
FSF_QTCB_OPEN_PORT_WITH_DID or FSF_QTCB_CLOSE_PORT or
FSF_QTCB_CLOSE_PHYSICAL_PORT for target ports,
FSF_QTCB_OPEN_LUN, FSF_QTCB_CLOSE_LUN.
One example is slow queue processing which can cause follow-on errors,
e.g. FSF_PORT_ALREADY_OPEN after FSF_QTCB_OPEN_PORT_WITH_DID timed out.
In order to see the root cause, we need to see late responses even if the
channel presented them successfully with FSF_PROT_GOOD and FSF_GOOD.
Example trace records formatted with zfcpdbf from the s390-tools package:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : ...
Record ID : 1
Tag : fcegpf1
LUN : 0xffffffffffffffff
WWPN : 0x<WWPN>
D_ID : 0x00<D_ID>
Adapter status : 0x5400050b
Port status : 0x41200000
LUN status : 0x00000000
Ready count : 0x00000001
Running count : 0x...
ERP want : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
ERP need : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
|
Timestamp : ... 30 seconds later
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : ...
Record ID : 2
Tag : erscf_2
LUN : 0xffffffffffffffff
WWPN : 0x<WWPN>
D_ID : 0x00<D_ID>
Adapter status : 0x5400050b
Port status : 0x41200000
LUN status : 0x00000000
Request ID : 0x<request_ID>
ERP status : 0x10000000 ZFCP_STATUS_ERP_TIMEDOUT
ERP step : 0x0800 ZFCP_ERP_STEP_PORT_OPENING
ERP action : 0x02 ZFCP_ERP_ACTION_REOPEN_PORT
ERP count : 0x00
|
Timestamp : ... later than previous record
Area : HBA
Subarea : 00
Level : 5 > default level => 3 <= default level
Exception : -
CPU ID : 00
Caller : ...
Record ID : 1
Tag : fs_qtcb => fs_rerr
Request ID : 0x<request_ID>
Request status : 0x00001010 ZFCP_STATUS_FSFREQ_DISMISSED
| ZFCP_STATUS_FSFREQ_CLEANUP
FSF cmnd : 0x00000005
FSF sequence no: 0x...
FSF issued : ... > 30 seconds ago
FSF stat : 0x00000000 FSF_GOOD
FSF stat qual : 00000000 00000000 00000000 00000000
Prot stat : 0x00000001 FSF_PROT_GOOD
Prot stat qual : 00000000 00000000 00000000 00000000
Port handle : 0x...
LUN handle : 0x00000000
QTCB log length: ...
QTCB log info : ...
In case of problems detecting that new responses are waiting on the input
queue, we sooner or later trigger adapter recovery due to an FSF request
timeout (trace tag "fsrth_1").
FSF requests with FSF request timeout are:
typically FSF_QTCB_ABORT_FCP_CMND; but theoretically also
FSF_QTCB_EXCHANGE_CONFIG_DATA or FSF_QTCB_EXCHANGE_PORT_DATA via sysfs,
FSF_QTCB_OPEN_PORT_WITH_DID or FSF_QTCB_CLOSE_PORT for WKA ports,
FSF_QTCB_FCP_CMND for task management function (LUN / target reset).
One or more pending requests can meanwhile have FSF_PROT_GOOD and FSF_GOOD
because the channel filled in the response via DMA into the request's QTCB.
In a theroretical case, inject code can create an erroneous FSF request
on purpose. If data router is enabled, it uses deferred error reporting.
A READ SCSI command can succeed with FSF_PROT_GOOD, FSF_GOOD, and
SAM_STAT_GOOD. But on writing the read data to host memory via DMA,
it can still fail, e.g. if an intentionally wrong scatter list does not
provide enough space. Rather than getting an unsuccessful response,
we get a QDIO activate check which in turn triggers adapter recovery.
One or more pending requests can meanwhile have FSF_PROT_GOOD and FSF_GOOD
because the channel filled in the response via DMA into the request's QTCB.
Example trace records formatted with zfcpdbf from the s390-tools package:
Timestamp : ...
Area : HBA
Subarea : 00
Level : 6 > default level => 3 <= default level
Exception : -
CPU ID : ..
Caller : ...
Record ID : 1
Tag : fs_norm => fs_rerr
Request ID : 0x<request_ID2>
Request status : 0x00001010 ZFCP_STATUS_FSFREQ_DISMISSED
| ZFCP_STATUS_FSFREQ_CLEANUP
FSF cmnd : 0x00000001
FSF sequence no: 0x...
FSF issued : ...
FSF stat : 0x00000000 FSF_GOOD
FSF stat qual : 00000000 00000000 00000000 00000000
Prot stat : 0x00000001 FSF_PROT_GOOD
Prot stat qual : ........ ........ 00000000 00000000
Port handle : 0x...
LUN handle : 0x...
|
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 3
Exception : -
CPU ID : ..
Caller : ...
Record ID : 1
Tag : rsl_err
Request ID : 0x<request_ID2>
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x000e0000 DID_TRANSPORT_DISRUPTED
SCSI retries : 0x00
SCSI allowed : 0x05
SCSI scribble : 0x<request_ID2>
SCSI opcode : 28... Read(10)
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000000 00000000
^^ SAM_STAT_GOOD
00000000 00000000
Only with luck in both above cases, we could see a follow-on trace record
of an unsuccesful event following a successful but late FSF response with
FSF_PROT_GOOD and FSF_GOOD. Typically this was the case for I/O requests
resulting in a SCSI trace record "rsl_err" with DID_TRANSPORT_DISRUPTED
[On ZFCP_STATUS_FSFREQ_DISMISSED, zfcp_fsf_protstatus_eval() sets
ZFCP_STATUS_FSFREQ_ERROR seen by the request handler functions as failure].
However, the reason for this follow-on trace was invisible because the
corresponding HBA trace record was missing at the default trace level
(by default hidden records with tags "fs_norm", "fs_qtcb", or "fs_open").
On adapter recovery, after we had shut down the QDIO queues, we perform
unsuccessful pseudo completions with flag ZFCP_STATUS_FSFREQ_DISMISSED
for each pending FSF request in zfcp_fsf_req_dismiss_all().
In order to find the root cause, we need to see all pseudo responses even
if the channel presented them successfully with FSF_PROT_GOOD and FSF_GOOD.
Therefore, check zfcp_fsf_req.status for ZFCP_STATUS_FSFREQ_DISMISSED
or ZFCP_STATUS_FSFREQ_ERROR and trace with a new tag "fs_rerr".
It does not matter that there are numerous places which set
ZFCP_STATUS_FSFREQ_ERROR after the location where we trace an FSF response
early. These cases are based on protocol status != FSF_PROT_GOOD or
== FSF_PROT_FSF_STATUS_PRESENTED and are thus already traced by default
as trace tag "fs_perr" or "fs_ferr" respectively.
NB: The trace record with tag "fssrh_1" for status read buffers on dismiss
all remains. zfcp_fsf_req_complete() handles this and returns early.
All other FSF request types are handled separately and as described above.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 8a36e4532e ("[SCSI] zfcp: enhancement of zfcp debug features")
Fixes: 2e261af84c ("[SCSI] zfcp: Only collect FSF/HBA debug data for matching trace levels")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 12c3e5754c upstream.
If the FCP_RSP UI has optional parts (FCP_SNS_INFO or FCP_RSP_INFO) and
thus does not fit into the fsp_rsp field built into a SCSI trace record,
trace the full FCP_RSP UI with all optional parts as payload record
instead of just FCP_SNS_INFO as payload and
a 1 byte RSP_INFO_CODE part of FCP_RSP_INFO built into the SCSI record.
That way we would also get the full FCP_SNS_INFO in case a
target would ever send more than
min(SCSI_SENSE_BUFFERSIZE==96, ZFCP_DBF_PAY_MAX_REC==256)==96.
The mandatory part of FCP_RSP IU is only 24 bytes.
PAYload costs at least one full PAY record of 256 bytes anyway.
We cap to the hardware response size which is only FSF_FCP_RSP_SIZE==128.
So we can just put the whole FCP_RSP IU with any optional parts into
PAYload similarly as we do for SAN PAY since v4.9 commit aceeffbb59
("zfcp: trace full payload of all SAN records (req,resp,iels)").
This does not cause any additional trace records wasting memory.
Decoded trace records were confusing because they showed a hard-coded
sense data length of 96 even if the FCP_RSP_IU field FCP_SNS_LEN showed
actually less.
Since the same commit, we set pl_len for SAN traces to the full length of a
request/response even if we cap the corresponding trace.
In contrast, here for SCSI traces we set pl_len to the pre-computed
length of FCP_RSP IU considering SNS_LEN or RSP_LEN if valid.
Nonetheless we trace a hardcoded payload of length FSF_FCP_RSP_SIZE==128
if there were optional parts.
This makes it easier for the zfcpdbf tool to format only the relevant
part of the long FCP_RSP UI buffer. And any trailing information is still
available in the payload trace record just in case.
Rename the payload record tag from "fcp_sns" to "fcp_riu" to make the new
content explicit to zfcpdbf which can then pick a suitable field name such
as "FCP rsp IU all:" instead of "Sense info :"
Also, the same zfcpdbf can still be backwards compatible with "fcp_sns".
Old example trace record before this fix, formatted with the tool zfcpdbf
from s390-tools:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 3
Exception : -
CPU id : ..
Caller : 0x...
Record id : 1
Tag : rsl_err
Request id : 0x<request_id>
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x00000002
SCSI retries : 0x00
SCSI allowed : 0x05
SCSI scribble : 0x<request_id>
SCSI opcode : 00000000 00000000 00000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000202 00000000
^^==FCP_SNS_LEN_VALID
00000020 00000000
^^^^^^^^==FCP_SNS_LEN==32
Sense len : 96 <==min(SCSI_SENSE_BUFFERSIZE,ZFCP_DBF_PAY_MAX_REC)
Sense info : 70000600 00000018 00000000 29000000
00000400 00000000 00000000 00000000
00000000 00000000 00000000 00000000<==superfluous
00000000 00000000 00000000 00000000<==superfluous
00000000 00000000 00000000 00000000<==superfluous
00000000 00000000 00000000 00000000<==superfluous
New example trace records with this fix:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 3
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : rsl_err
Request ID : 0x<request_id>
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x00000002
SCSI retries : 0x00
SCSI allowed : 0x03
SCSI scribble : 0x<request_id>
SCSI opcode : a30c0112 00000000 02000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000a02 00000200
00000020 00000000
FCP rsp IU len : 56
FCP rsp IU all : 00000000 00000000 00000a02 00000200
^^=FCP_RESID_UNDER|FCP_SNS_LEN_VALID
00000020 00000000 70000500 00000018
^^^^^^^^==FCP_SNS_LEN
^^^^^^^^^^^^^^^^^
00000000 240000cb 00011100 00000000
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
00000000 00000000
^^^^^^^^^^^^^^^^^==FCP_SNS_INFO
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : lr_okay
Request ID : 0x<request_id>
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x00000000
SCSI retries : 0x00
SCSI allowed : 0x05
SCSI scribble : 0x<request_id>
SCSI opcode : <CDB of unrelated SCSI command passed to eh handler>
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000100 00000000
00000000 00000008
FCP rsp IU len : 32
FCP rsp IU all : 00000000 00000000 00000100 00000000
^^==FCP_RSP_LEN_VALID
00000000 00000008 00000000 00000000
^^^^^^^^==FCP_RSP_LEN
^^^^^^^^^^^^^^^^^==FCP_RSP_INFO
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 250a1352b9 ("[SCSI] zfcp: Redesign of the debug tracing for SCSI records.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a5d999ebf upstream.
For problem determination we need to see that we were in scsi_eh
as well as whether and why we were successful or not.
The following commits introduced new early returns without adding
a trace record:
v2.6.35 commit a1dbfddd02
("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh")
on fc_block_scsi_eh() returning != 0 which is FAST_IO_FAIL,
v2.6.30 commit 63caf367e1
("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp")
on not having gotten an FSF request after the maximum number of retry
attempts and thus could not issue a TMF and has to return FAILED.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: a1dbfddd02 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh")
Fixes: 63caf367e1 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9fe5d2b2fd upstream.
Without this fix we get SCSI trace records on task management functions
which cannot be correlated to HBA trace records because all fields
related to the FSF request are empty (zero).
Also, the FCP_RSP_IU is missing as well as any sense data if available.
This was caused by v2.6.14 commit 8a36e4532e ("[SCSI] zfcp: enhancement
of zfcp debug features") introducing trace records for TMFs but
hard coding NULL for a possibly existing TMF FSF request.
The scsi_cmnd scribble is also zero or unrelated for the TMF request
so it also could not lookup a suitable FSF request from there.
A broken example trace record formatted with zfcpdbf from the s390-tools
package:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : lr_fail
Request ID : 0x0000000000000000
^^^^^^^^^^^^^^^^ no correlation to HBA record
SCSI ID : 0x<scsitarget>
SCSI LUN : 0x<scsilun>
SCSI result : 0x000e0000
SCSI retries : 0x00
SCSI allowed : 0x05
SCSI scribble : 0x0000000000000000
SCSI opcode : 2a000017 3bb80000 08000000 00000000
FCP rsp inf cod: 0x00
^^ no TMF response
FCP rsp IU : 00000000 00000000 00000000 00000000
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
00000000 00000000
^^^^^^^^^^^^^^^^^ no interesting FCP_RSP_IU
Sense len : ...
^^^^^^^^^^^^^^^^^^^^ no sense data length
Sense info : ...
^^^^^^^^^^^^^^^^^^^^ no sense data content, even if present
There are some true cases where we really do not have an FSF request:
"rsl_fai" from zfcp_dbf_scsi_fail_send() called for early
returns / completions in zfcp_scsi_queuecommand(),
"abrt_or", "abrt_bl", "abrt_ru", "abrt_ar" from
zfcp_scsi_eh_abort_handler() where we did not get as far,
"lr_nres", "tr_nres" from zfcp_task_mgmt_function() where we're
successful and do not need to do anything because adapter stopped.
For these cases it's correct to pass NULL for fsf_req to _zfcp_dbf_scsi().
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 8a36e4532e ("[SCSI] zfcp: enhancement of zfcp debug features")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 975171b446 upstream.
v4.9 commit aceeffbb59 ("zfcp: trace full payload of all SAN records
(req,resp,iels)") fixed trace data loss of 2.6.38 commit 2c55b750a8
("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
necessary for problem determination, e.g. to see the
currently active zone set during automatic port scan.
While it already saves space by not dumping any empty residual entries
of the large successful GPN_FT response (4 pages), there are seldom cases
where the GPN_FT response is unsuccessful and likely does not have
FC_NS_FID_LAST set in fp_flags so we did not cap the trace record.
We typically see such case for an initiator WWPN, which is not in any zone.
Cap unsuccessful responses to at least the actual basic CT_IU response
plus whatever fits the SAN trace record built-in "payload" buffer
just in case there's trailing information
of which we would at least see the existence and its beginning.
In order not to erroneously cap successful responses, we need to swap
calling the trace function and setting the CT / ELS status to success (0).
Example trace record pair formatted with zfcpdbf:
Timestamp : ...
Area : SAN
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : fssct_1
Request ID : 0x<request_id>
Destination ID : 0x00fffffc
SAN req short : 01000000 fc020000 01720ffc 00000000
00000008
SAN req length : 20
|
Timestamp : ...
Area : SAN
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 2
Tag : fsscth2
Request ID : 0x<request_id>
Destination ID : 0x00fffffc
SAN resp short : 01000000 fc020000 80010000 00090700
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
SAN resp length: 16384
San resp info : 01000000 fc020000 80010000 00090700
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
00000000 00000000 00000000 00000000 [trailing info]
The fix saves all but one of the previously associated 64 PAYload trace
record chunks of size 256 bytes each.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: aceeffbb59 ("zfcp: trace full payload of all SAN records (req,resp,iels)")
Fixes: 2c55b750a8 ("[SCSI] zfcp: Redesign of the debug tracing for SAN records.")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a099b7b1fc upstream.
Up until now zfcp would just ignore the FCP_RESID_OVER flag in the FCP
response IU. When this flag is set, it is possible, in regards to the
FCP standard, that the storage-server processes the command normally, up
to the point where data is missing and simply ignores those.
In this case no CHECK CONDITION would be set, and because we ignored the
FCP_RESID_OVER flag we resulted in at least a data loss or even
-corruption as a follow-up error, depending on how the
applications/layers on top behave. To prevent this, we now set the
host-byte of the corresponding scsi_cmnd to DID_ERROR.
Other storage-behaviors, where the same condition results in a CHECK
CONDITION set in the answer, don't need to be changed as they are
handled in the mid-layer already.
Following is an example trace record decoded with zfcpdbf from the
s390-tools package. We forcefully injected a fc_dl which is one byte too
small:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 3
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : rsl_err
Request ID : 0x...
SCSI ID : 0x...
SCSI LUN : 0x...
SCSI result : 0x00070000
^^DID_ERROR
SCSI retries : 0x..
SCSI allowed : 0x..
SCSI scribble : 0x...
SCSI opcode : 2a000000 00000000 08000000 00000000
FCP rsp inf cod: 0x00
FCP rsp IU : 00000000 00000000 00000400 00000001
^^fr_flags==FCP_RESID_OVER
^^fr_status==SAM_STAT_GOOD
^^^^^^^^fr_resid
00000000 00000000
As of now, we don't actively handle to possibility that a response IU
has both flags - FCP_RESID_OVER and FCP_RESID_UNDER - set at once.
Reported-by: Luke M. Hopkins <lmhopkin@us.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: 553448f6c4 ("[SCSI] zfcp: Message cleanup")
Fixes: ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.") (tglx/history.git)
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 71b8e45da5 upstream.
Since commit db007fc5e2 ("[SCSI] Command protection operation"),
scsi_eh_prep_cmnd() saves scmd->prot_op and temporarily resets it to
SCSI_PROT_NORMAL.
Other FCP LLDDs such as qla2xxx and lpfc shield their queuecommand()
to only access any of scsi_prot_sg...() if
(scsi_get_prot_op(cmd) != SCSI_PROT_NORMAL).
Do the same thing for zfcp, which introduced DIX support with
commit ef3eb71d8b ("[SCSI] zfcp: Introduce experimental support for
DIF/DIX").
Otherwise, TUR SCSI commands as part of scsi_eh likely fail in zfcp,
because the regular SCSI command with DIX protection data, that scsi_eh
re-uses in scsi_send_eh_cmnd(), of course still has
(scsi_prot_sg_count() != 0) and so zfcp sends down bogus requests to the
FCP channel hardware.
This causes scsi_eh_test_devices() to have (finish_cmds == 0)
[not SCSI device is online or not scsi_eh_tur() failed]
so regular SCSI commands, that caused / were affected by scsi_eh,
are moved to work_q and scsi_eh_test_devices() itself returns false.
In turn, it unnecessarily escalates in our case in scsi_eh_ready_devs()
beyond host reset to finally scsi_eh_offline_sdevs()
which sets affected SCSI devices offline with the following kernel message:
"kernel: sd H:0:T:L: Device offlined - not ready after error recovery"
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Fixes: ef3eb71d8b ("[SCSI] zfcp: Introduce experimental support for DIF/DIX")
Reviewed-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Benjamin Block <bblock@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5fbd545cd3 upstream.
Ensure that the members of struct skd_msg_buf have been transferred
to the PCIe adapter before the doorbell is triggered. This patch
avoids that I/O fails sporadically and that the following error
message is reported:
(skd0:STM000196603:[0000:00:09.0]): Completion mismatch comp_id=0x0000 skreq=0x0400 new=0x0000
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8a27f836f upstream.
bitmap_resize() does not work for file-backed bitmaps.
The buffer_heads are allocated and initialized when
the bitmap is read from the file, but resize doesn't
read from the file, it loads from the internal bitmap.
When it comes time to write the new bitmap, the bh is
non-existent and we crash.
The common case when growing an array involves making the array larger,
and that normally means making the bitmap larger. Doing
that inside the kernel is possible, but would need more code.
It is probably easier to require people who use file-backed
bitmaps to remove them and re-add after a reshape.
So this patch disables the resizing of arrays which have
file-backed bitmaps. This is better than crashing.
Reported-by: Zhilong Liu <zlliu@suse.com>
Fixes: d60b479d17 ("md/bitmap: add bitmap_resize function to allow bitmap resizing.")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8031c3ddc7 upstream.
raid5 cache could write bitmap superblock before bitmap superblock is
initialized. The bitmap superblock is less than 512B. The current code will
only copy the superblock to a new page and write the whole 512B, which will
zero the the data after the superblock. Unfortunately the data could include
bitmap, which we should preserve. The patch will make superblock read do 4k
chunk and we always copy the 4k data to new page, so the superblock write will
old data to disk and we don't change the bitmap.
Reported-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 197267d035 upstream.
cxl keeps a driver use count, which is used with the hash memory model
on p8 to know when to upgrade local TLBIs to global and to trigger
callbacks to manage the MMU for PSL8.
If a process opens a context and closes without attaching or fails the
attachment, the driver use count is never decremented. As a
consequence, TLB invalidations remain global, even if there are no
active cxl contexts.
We should increment the driver use count when the process is attaching
to the cxl adapter, and not on open. It's not needed before the
adapter starts using the context and the use count is decremented on
the detach path, so it makes more sense.
It affects only the user api. The kernel api is already doing The
Right Thing.
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Fixes: 7bb5d91a4d ("cxl: Rework context lifetimes")
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39efc7cc7c upstream.
As the association status changes the driver needs to configure the
hardware. This is done based on information in the "sta" acquired by
ieee80211_find_sta(), which requires the caller to ensure that the "sta"
is valid while its being used; generally by entering an rcu read
section.
But the operations acting on the "sta" has to communicate with the
firmware and may therefor sleep, resulting in the following report:
[ 31.418190] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:238
[ 31.425919] in_atomic(): 0, irqs_disabled(): 0, pid: 34, name:
kworker/u8:1
[ 31.434609] CPU: 0 PID: 34 Comm: kworker/u8:1 Tainted: G W
4.12.0-rc4-next-20170607+ #993
[ 31.441002] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC
(DT)
[ 31.450380] Workqueue: phy0 ieee80211_iface_work
[ 31.457226] Call trace:
[ 31.461830] [<ffffff8008088c58>] dump_backtrace+0x0/0x260
[ 31.464004] [<ffffff8008088f7c>] show_stack+0x14/0x20
[ 31.469557] [<ffffff8008392e70>] dump_stack+0x98/0xb8
[ 31.474592] [<ffffff80080e4330>] ___might_sleep+0xf0/0x118
[ 31.479626] [<ffffff80080e43a8>] __might_sleep+0x50/0x88
[ 31.485010] [<ffffff80088ff9a4>] mutex_lock+0x24/0x60
[ 31.490479] [<ffffff8008595c38>] wcn36xx_smd_set_link_st+0x30/0x130
[ 31.495428] [<ffffff8008591ed8>] wcn36xx_bss_info_changed+0x148/0x448
[ 31.501504] [<ffffff80088ab3c4>]
ieee80211_bss_info_change_notify+0xbc/0x118
[ 31.508102] [<ffffff80088f841c>] ieee80211_assoc_success+0x664/0x7f8
[ 31.515220] [<ffffff80088e13d4>]
ieee80211_rx_mgmt_assoc_resp+0x144/0x2d8
[ 31.521555] [<ffffff80088e1e20>]
ieee80211_sta_rx_queued_mgmt+0x190/0x698
[ 31.528239] [<ffffff80088bc44c>] ieee80211_iface_work+0x234/0x368
[ 31.535011] [<ffffff80080d81ac>] process_one_work+0x1cc/0x340
[ 31.541086] [<ffffff80080d8368>] worker_thread+0x48/0x430
[ 31.546814] [<ffffff80080de448>] kthread+0x108/0x138
[ 31.552195] [<ffffff8008082ec0>] ret_from_fork+0x10/0x50
In order to ensure that the "sta" remains alive (and consistent) for the
duration of bss_info_changed() mutual exclusion has to be ensured with
sta_remove().
This is done by introducing a mutex to cover firmware configuration
changes, which is made to also ensure mutual exclusion between other
operations changing the state or configuration of the firmware. With
this we can drop the rcu read lock.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91a024e803 upstream.
The original patch from Tony uses standby mode bit inverted, which is
not correct. This fixes all instances in the driver code for get & set
mode. This did not yet make problems, since mode has not been changed
by any mainline driver so far.
Fixes: 0ad4c07edd ("regulator: cpcap: Add basic regulator support")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a68a193805 upstream.
caam/qi needs a fix similar to what was done for caam/jr in
commit "crypto: caam/qi - properly set IV after {en,de}crypt",
to allow for ablkcipher/skcipher chunking/streaming.
Fixes: b189817cf7 ("crypto: caam/qi - add ablkcipher and authenc algorithms")
Suggested-by: David Gstir <david@sigma-star.at>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e652399edb upstream.
Version 5 CCPs have some new requirements for XTS-AES: the type field
must be specified, and the key requires 512 bits, with each part
occupying 256 bits and padded with zeroes.
Signed-off-by: Gary R Hook <ghook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 697c5d8a36 upstream.
Similar to other Gigabyte laptops, the touchpad on P57 requires a
keyboard reset to detect Elantech touchpad correctly.
BugLink: https://bugs.launchpad.net/bugs/1594214
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79d2c8bede upstream.
The touchpad in the Asus laptop models X505BA/BP and X542BA/BP is
unresponsive after suspend/resume. The following error appears during
resume:
i2c_hid i2c-ELAN1300:00: failed to reset device.
The problem here is that i2c_hid does not notice the interrupt being
generated at this point, because the GPIO is no longer configured
for interrupts.
Fix this by saving pinctrl-amd pin registers during suspend and
restoring them at resume time.
Based on code from pinctrl-intel.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cee7413d84 upstream.
After commit 8b1bd11c1f ("pinctrl: samsung: Add the support the
multiple IORESOURCE_MEM for one pin-bank"), the S3C24xx (and probably
S3C64xx as well) fails:
Unable to handle kernel NULL pointer dereference at virtual address 000000a8
...
(s3c24xx_demux_eint4_7) from [<c004469c>] (__handle_domain_irq+0x6c/0xcc)
(__handle_domain_irq) from [<c0009444>] (s3c24xx_handle_irq+0x6c/0x12c)
(s3c24xx_handle_irq) from [<c000e5fc>] (__irq_svc+0x5c/0x78)
Mentioned commit moved the pointer to controller's base IO memory address
from each controller's driver data (samsung_pinctrl_drv_data) to per-bank
structure (samsung_pin_bank). The external interrupt demux
handlers (s3c24xx_demux_eint()) tried to get this base address from opaque
pointer stored under irq_chip data:
struct irq_data *irqd = irq_desc_get_irq_data(desc);
struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
...
pend = readl(bank->eint_base + EINTPEND_REG);
which is wrong because this is hardware irq and it bank was never set
for this irq_chip.
For S3C24xx and S3C64xx, this partially reverts mentioned commit by
bringing back the virt_base stored under each controller's driver data
(samsung_pinctrl_drv_data). This virt_base address will be now
duplicated:
- samsung_pinctrl_drv_data->virt_base: used on S3C24xx and S3C64xx,
- samsung_pin_bank->pctl_base: used on Exynos.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reported-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Lihua Yao <ylhuajnu@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit af0b0baa89 upstream.
When setting the pin function for external interrupts, the driver used
wrong IO memory address base. The pin function register is always under
pctl_base, not the eint_base.
By updating wrong register, the external interrupts for chosen GPIO
would not work at all and some other GPIO might be configured to wrong
value. For example on Exynos5433-based boards, the external interrupts
for gpf{1-5}-X GPIOs should not work at all (driver toggled reserved
registers from ALIVE bank instead).
Platforms other than Exynos5433 should not be affected as eint_base
equals pctl_base in such case.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Reported-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8a5a90a2a4 upstream.
Sergey noticed a small but fatal mistake in __tty_insert_flip_char,
leading to an oops in an interrupt handler when using any serial
port.
The problem is that I accidentally took the tty_buffer pointer
before calling __tty_buffer_request_room(), which replaces the
buffer. This moves the pointer lookup to the right place after
allocating the new buffer space.
Fixes: 979990c628 ("tty: improve tty_insert_flip_char() fast path")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 065ea0a7af upstream.
While working on improving the fast path of tty_insert_flip_char(),
I noticed that by calling tty_buffer_request_room(), we needlessly
move to the separate flag buffer mode for the tty, even when all
characters use TTY_NORMAL as the flag.
This changes the code to call __tty_buffer_request_room() with the
correct flag, which will then allocate a regular buffer when it rounds
out of space but no special flags have been used. I'm guessing that
this is the behavior that Peter Hurley intended when he introduced
the compacted flip buffers.
Fixes: acc0f67f30 ("tty: Halve flip buffer GFP_ATOMIC memory consumption")
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 979990c628 upstream.
kernelci.org reports a crazy stack usage for the VT code when CONFIG_KASAN
is enabled:
drivers/tty/vt/keyboard.c: In function 'kbd_keycode':
drivers/tty/vt/keyboard.c:1452:1: error: the frame size of 2240 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
The problem is that tty_insert_flip_char() gets inlined many times into
kbd_keycode(), and also into other functions, and each copy requires 128
bytes for stack redzone to check for a possible out-of-bounds access on
the 'ch' and 'flags' arguments that are passed into
tty_insert_flip_string_flags as a variable-length string.
This introduces a new __tty_insert_flip_char() function for the slow
path, which receives the two arguments by value. This completely avoids
the problem and the stack usage goes back down to around 100 bytes.
Without KASAN, this is also slightly better, as we don't have to
spill the arguments to the stack but can simply pass 'ch' and 'flag'
in registers, saving a few bytes in .text for each call site.
This should be backported to linux-4.0 or later, which first introduced
the stack sanitizer in the kernel.
Fixes: c420f167db ("kasan: enable stack instrumentation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 122d6a3473 upstream.
We should only see devices with interrupt endpoints. Ignore any other
endpoints that we find, so we don't send try to send them interrupt URBs
and trigger a WARN down in the USB stack.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c25b7a390 upstream.
When we have a miss in one order of the mkey cache, we try to get
an mkey from a higher order.
We still need to check that the higher order can be used with UMR
before using it. Otherwise, we will get an mkey with 0 entries and
the post send operation that is used to fill it will complete with
the following error:
mlx5_0:dump_cqe:275:(pid 0): dump error cqe
00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000
00000000 0f007806 25000025 49ce59d2
Fixes: 49780d42df ("IB/mlx5: Expose MR cache for mlx5_ib")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b0ef650bd upstream.
Section 9.7.7.2.5 of the 1.3 IBTA spec clearly says that receive
credits should never apply to RDMA write.
qib and hfi1 were doing that. The following situation will result
in a QP hang:
- A prior SEND or RDMA_WRITE with immmediate consumed the last
credit for a QP using RC receive buffer credits
- The prior op is acked so there are no more acks
- The peer ULP fails to post receive for some reason
- An RDMA write sees that the credits are exhausted and waits
- The peer ULP posts receive buffers
- The ULP posts a send or RDMA write that will be hung
The fix is to avoid the credit test for the RDMA write operation.
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ecdb19f4b5 upstream.
Current code has some serious flaws. Disarm the flag
pending an appropriate patch.
Fixes: 53526500f3 ("IB/hfi1: Permanently enable P_Key checking in HFI")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Alex Estrin <alex.estrin@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9c72a18e46 upstream.
In raid5, there are scenarios where some ios are deferred to a later
time, and some IO need a flush to complete. To make sure we make
progress with these IOs, we need to call the following functions:
flush_deferred_bios(conf);
r5l_flush_stripe_to_raid(conf->log);
Both of these functions are called in raid5d(), but missing in
raid5_do_work(). As a result, these functions are not called
when multi-threading (group_thread_cnt > 0) is enabled. This patch
adds calls to these function to raid5_do_work().
Note for stable branches:
r5l_flush_stripe_to_raid(conf->log) is need for 4.4+
flush_deferred_bios(conf) is only needed for 4.11+
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 208410b546 upstream.
Data allocated from mempool doesn't always get initialized, this happens when
the data is reused instead of fresh allocation. In the raid1/10 case, we must
reinitialize the bios.
Reported-by: Jonathan G. Underwood <jonathan.underwood@gmail.com>
Fixes: f0250618361d(md: raid10: don't use bio's vec table to manage resync pages)
Fixes: 98d30c5812c3(md: raid1: don't use bio's vec table to manage resync pages)
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58738c495e upstream.
Dan reports:
The patch 62232e45f4: "libnvdimm: control (ioctl) messages for
nvdimm_bus and nvdimm devices" from Jun 8, 2015, leads to the
following static checker warning:
drivers/nvdimm/bus.c:1018 __nd_ioctl()
warn: integer overflows 'buf_len'
From a casual review, this seems like it might be a real bug. On
the first iteration we load some data into in_env[]. On the second
iteration we read a use controlled "in_size" from nd_cmd_in_size().
It can go up to UINT_MAX - 1. A high number means we will fill the
whole in_env[] buffer. But we potentially keep looping and adding
more to in_len so now it can be any value.
It simple enough to change, but it feels weird that we keep looping
even though in_env is totally full. Shouldn't we just return an
error if we don't have space for desc->in_num.
We keep looping because the size of the total input is allowed to be
bigger than the 'envelope' which is a subset of the payload that tells
us how much data to expect. For safety explicitly check that buf_len
does not overflow which is what the checker flagged.
Fixes: 62232e45f4: "libnvdimm: control (ioctl) messages for nvdimm_bus..."
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ed36b4dba5 upstream.
Check memory allocation failures and return -ENOMEM in such cases, as
already done few lines below for another memory allocation.
This avoids NULL pointers dereference.
Fixes: 14e4945426 ("libnvdimm, btt: BTT updates for UEFI 2.7 format")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e545f0d8a5 upstream.
If secure authentication of a devices fails, either because the device
already has another key uploaded, or there is some other error sending
challenge to the device, and the user only wants to approve the device
just once (without a new key being uploaded to the device) the current
implementation does not allow this because the key cannot be cleared
once set even if we allow it to be changed.
Make this scenario possible and allow clearing the key by writing
empty string to the key sysfs file.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0956e41169 upstream.
Non-root user may read the key back after root wrote it there.
This removes read access to everyone but root.
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8b949bef91 ]
We check tx avail through vhost_enable_notify() in the past which is
wrong since it only checks whether or not guest has filled more
available buffer since last avail idx synchronization which was just
done by vhost_vq_avail_empty() before. What we really want is checking
pending buffers in the avail ring. Fix this by calling
vhost_vq_avail_empty() instead.
This issue could be noticed by doing netperf TCP_RR benchmark as
client from guest (but not host). With this fix, TCP_RR from guest to
localhost restores from 1375.91 trans per sec to 55235.28 trans per
sec on my laptop (Intel(R) Core(TM) i7-5600U CPU @ 2.60GHz).
Fixes: 0308813724 ("vhost_net: basic polling support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d621672bc ]
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83ec489193 upstream.
Since commit 41977e86c9 ("rt2x00: add support for MT7620") we do not
initialize TX_PIN_CFG setting. This cause breakage at least on some
RT3573 devices. To fix the problem patch restores previous behaviour
for non MT7620 chips.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1480829
Reported-and-tested-by: Jussi Eloranta <jussi.eloranta@csun.edu>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f007cad159 upstream.
This reverts commit 81f9507628.
It causes random failures of firmware loading at resume time (well,
random for me, it seems to be more reliable for others) because the
firmware disabling is not actually synchronous with any particular
resume event, and at least the btusb driver that uses a workqueue to
load the firmware at resume seems to occasionally hit the "firmware
loading is disabled" logic because the firmware loader hasn't gotten the
resume event yet.
Some kind of sanity check for not trying to load firmware when it's not
possible might be a good thing, but this commit was not it.
Greg seems to have silently suffered the same issue, and pointed to the
likely culprit, and Gabriel C verified the revert fixed it for him too.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Pointed-at-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Gabriel C <nix.or.die@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f957dd3c8d upstream.
The firmware feature check introduced for multi-scheduled scan is also
failing for bcm4345 devices resulting in a firmware crash.
The reason for this crash has not yet been root cause so this patch avoids
the feature check for those device as a short-term fix.
Fixes: 9fe929aaac ("brcmfmac: add firmware feature detection for gscan feature")
Signed-off-by: Ian W MORRISON <ianwmorrison@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d62269283 upstream.
In commit 87d8a9f352 ("rtlwifi: btcoex: call bind to setup btcoex"),
the code turns on a call to exhalbtc_bind_bt_coex_withadapter(). This
routine contains a bug that causes incorrect antenna selection for those
HP laptops with only one antenna and an incorrectly programmed EFUSE.
These boxes are the ones that need the ant_sel module parameter.
Fixes: 87d8a9f352 ("rtlwifi: btcoex: call bind to setup btcoex")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a33fcba6ec upstream.
In commit bcd37f4a08 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when
hw initialisation done"), there is an additional error when the module
parameter ant_sel is used to select the auxilary antenna. The error is
that the antenna selection is not checked when writing the antenna
selection register.
Fixes: bcd37f4a08 ("rtlwifi: btcoex: 23b 2ant: let bt transmit when hw initialisation done")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40a5fce495 upstream.
The default host NQN, which is generated based on the host's UUID,
does not follow the UUID-based NQN format laid out in the NVMe 1.3
specification. Remove the "NVMf:" portion of the NQN to match the spec.
Signed-off-by: Daniel Verkamp <daniel.verkamp@intel.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 10777de570 upstream.
The configuration for BCH is not correct in the current driver.
The ECC_CFG_ECC_DISABLE bit defines whether to enable or disable the
BCH ECC in which
0x1 : BCH_DISABLED
0x0 : BCH_ENABLED
But currently host->bch_enabled is being assigned to BCH_DISABLED.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d8a9b320a2 upstream.
The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is
0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID
The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bff08dffe upstream.
Commit a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).
Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>