Currently, we hold a max of sch->limit -1 number of packets instead of
sch->limit packets. Fix this off-by-one error.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d0418bb712 (net: sh_eth: Add eth support
for R8A7779 device) was a failed attempt to add support for one of members of
the R-Car SoC family. That's for three reasons: it treated R8A7779 the same
as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask
in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in
R-Car Ether), and it didn't add a new register offset array despite the closest
SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether
registers have, and also some of the registers in this old mapping don't exist
on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not
adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724
related section to its pristine state...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver's header file contains initialized register offset tables which (as
any data definitions), of course, have no business being there. Move them to
the driver's body, somewhat beautifying the initializers, while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WOL is broken because the magic packet status bit is getting set rather
than the enable bit. The PMT interrupt is not getting serviced because
the PMT interrupt is also enabled on the global interrupt, but not
cleared by the global interrupt and the global interrupt is higher
priority. This fixes both of these issues to get WOL working.
There's still a problem with receive after resume, but at least now we
can wake-up.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb allocation for the rx ring fails repeatedly, we can reach a point
were the ring is empty. In this condition, the driver is out of sync with
the h/w. While this has always been possible, the removal of the skb
recycling seems to have made triggering this problem easier.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rtnl_fdb_dump() when the fdb_dump ndo op is not populated
we never set the idx value so that cb->arg[0] is always 0.
Resulting in a endless loop of messages.
Introduced with this commit,
commit 090096bf3d
Author: Vlad Yasevich <vyasevic@redhat.com>
Date: Wed Mar 6 15:39:42 2013 +0000
net: generic fdb support for drivers without ndo_fdb_<op>
CC: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'nf_reset' is called just prior calling 'netif_rx'.
No need to call it twice.
Reported-by: Igor Michailov <rgohita@gmail.com>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ben pointed out following patch fixes bug in checking device
name length limits while forming tunnel device name.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables RX of jumbo frames for LAN7500.
Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).
With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
replace per_cpu with per_cpu_ptr to save conversion between address and pointer
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_tasklet is not percpu var, and percpu is percpu var, and
this_cpu_ptr(&info->cache->percpu->flush_tasklet)
is not equal to
&this_cpu_ptr(info->cache->percpu)->flush_tasklet
1f743b076(use this_cpu_ptr per-cpu helper) introduced this bug.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current Tilera boot infrastructure now provides the initramfs
to Linux as a Tilera-hypervisor file named "initramfs", rather than
"initramfs.cpio.gz", as before. (This makes it reasonable to use
other compression techniques than gzip on the file without having to
worry about the name causing confusion.) Adapt to use the new name,
but also fall back to checking for the old name.
Cc'ing to stable so that older kernels will remain compatible with
newer Tilera boot infrastructure.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.kernel.org
Currently if either arp_interval or miimon is disabled, they both get
disabled, and upon disabling they get executed once more which is not
the proper behaviour. Also when doing a no-op and disabling an already
disabled one, the other again gets disabled.
Also fix the error messages with the proper valid ranges, and a small
typo fix in the up delay error message (outputting "down delay", instead
of "up delay").
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Hugne's errata proposal (Errata ID: 3480) to RFC4291 has been
verified: http://www.rfc-editor.org/errata_search.php?eid=3480
We have to check for pkt_type and loopback flag because either the
packets are allowed to travel over the loopback interface (in which case
pkt_type is PACKET_HOST and IFF_LOOPBACK flag is set) or they travel
over a non-loopback interface back to us (in which case PACKET_TYPE is
PACKET_LOOPBACK and IFF_LOOPBACK flag is not set).
Cc: Erik Hugne <erik.hugne@ericsson.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a
wrong value which leads to only 2kB of RAM remaining space. This can lead to
Rx overflow errors even with activated flow-control.
Fix: We should increase the value to 8192/8
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sky2 driver doesn't count the Receive Overflows because the MAC
interrupt for this event is not set in the MAC's interrupt mask.
The MAC's interrupt mask is set only for Transmit FIFO Underruns.
Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR)
Otherwise the Receive Overflow event will not generate any interrupt.
The Receive Overflow interrupt is handled correctly
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ceph fix from Sage Weil:
"This fixes a regression introduced during the last merge window when
mapping non-existent images."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: don't zero-fill non-image object requests
A result of ENOENT from a read request for an object that's part of
an rbd image indicates that there is a hole in that portion of the
image. Similarly, a short read for such an object indicates that
the remainder of the read should be interpreted a full read with
zeros filling out the end of the request.
This behavior is not correct for objects that are not backing rbd
image data. Currently rbd_img_obj_request_callback() assumes it
should be done for all objects.
Change rbd_img_obj_request_callback() so it only does this zeroing
for image objects. Encapsulate that special handling in its own
function. Add an assertion that the image object request is a bio
request, since we assume that (and we currently don't support any
other types).
This resolves a problem identified here:
http://tracker.ceph.com/issues/4559
The regression was introduced by bf0d5f503d.
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
Pull btrfs fixes from Chris Mason:
"We've had a busy two weeks of bug fixing. The biggest patches in here
are some long standing early-enospc problems (Josef) and a very old
race where compression and mmap combine forces to lose writes (me).
I'm fairly sure the mmap bug goes all the way back to the introduction
of the compression code, which is proof that fsx doesn't trigger every
possible mmap corner after all.
I'm sure you'll notice one of these is from this morning, it's a small
and isolated use-after-free fix in our scrub error reporting. I
double checked it here."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: don't drop path when printing out tree errors in scrub
Btrfs: fix wrong return value of btrfs_lookup_csum()
Btrfs: fix wrong reservation of csums
Btrfs: fix double free in the btrfs_qgroup_account_ref()
Btrfs: limit the global reserve to 512mb
Btrfs: hold the ordered operations mutex when waiting on ordered extents
Btrfs: fix space accounting for unlink and rename
Btrfs: fix space leak when we fail to reserve metadata space
Btrfs: fix EIO from btrfs send in is_extent_unchanged for punched holes
Btrfs: fix race between mmap writes and compression
Btrfs: fix memory leak in btrfs_create_tree()
Btrfs: fix locking on ROOT_REPLACE operations in tree mod log
Btrfs: fix missing qgroup reservation before fallocating
Btrfs: handle a bogus chunk tree nicely
Btrfs: update to use fs_state bit
Commit 3e7fc708eb ("ia64 idle: delete pm_idle") in 3.9-rc1 didn't
finish the job, leaving an un-initialized reference to (*idle)().
[ Haven't seen a crash from this - but seems like we are just being
lucky that "idle" is zero so it does get initialized before we jump to
randomland - Len ]
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull arc architecture fixes from Vineet Gupta:
"This includes fix for a serious bug in DMA mapping API, make
allyesconfig wreckage, removal of bogus email-list placeholder in
MAINTAINERS, a typo in ptrace helper code and last remaining changes
for syscall ABI v3 which we are finally starting to transition-to
internally.
The request is late than I intended to - but I was held up with
debugging a timer link list corruption, for which a proposed fix to
generic timer code was sent out to lkml/tglx earlier today."
* 'for-curr' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Fix the typo in event identifier flags used by ptrace
arc: fix dma_address assignment during dma_map_sg()
ARC: Remove SET_PERSONALITY (tracks cross-arch change)
ARC: ABIv3: fork/vfork wrappers not needed in "no-legacy-syscall" ABI
ARC: ABIv3: Print the correct ABI ver
ARC: make allyesconfig build breakages
ARC: MAINTAINERS update for ARC
Now that we have regular register mapped controls we should be splitting
the control sets for ADSP1 and ADSP2 as the register maps are not
identical. Do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't update info->update_val if write to the register fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The purpose of this patch is to guarantee that ab8500-debug will
record the regulator registers before they are modified by the
ab8500 regulator driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The USB regulator is controlled by hardware. The software support
was only needed for early hardware (ED) which is no longer supported.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for HW request is added in the external regulator
driver. A flag in the board configuration can be set to
let HW control the regulator when there is no SW request.
This means that the regulator will be put in high power
mode when there is a SW request and in HW-request mode
otherwise.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias NILSSON <mattias.i.nilsson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
v20 HREFs require non-standard configuration of EXT_SUPPLY2 to
function correctly (specific information is commented). Here we make
use of the recently added mechanism to adapt initialisation values
for such use-cases.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When older variants of the HREF (earlier than v22) development
platform enter suspend mode, power down EXT_SUPPLY1.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If particular platforms require non-standard initialisation values,
they can use this function to adapt them as required.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pass constraint information for recently supported external AB8500
controlled regulators. Also change the start-up initialisation settings
for each of the 3 supported external supplies to low-power, off and
high-power for supply 1, 2 and 3 respectively.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ABx500 is capable of controlling three external regulator supplies.
Most commonly on and off are supported, but if an external regulator
chipset or power supply supports high-power and low-power mode settings,
we can control those too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't treat it as an error if a partition is already in the same power
state when a user wants to power it on or off. This allows code to
proceed if no state change is required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This function can be used by drivers to enable power to the hardware
blocks that they drive. Most of the drivers can be built as a module
and therefore require this function to be exported.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This properly sets the modes of the sysfs files.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Clark Williams <williams@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9214d1d8 set the USB persist flag as a default for all devices.
This might be desirable for some distributions, but it certainly has its
trade-offs... most importantly, it can significantly increase system
resume time, because the kernel blocks on resuming (and sometimes
resetting) USB devices before it unfreezes userspace.
This patch introduces a new config option CONFIG_USB_DEFAULT_PERSIST,
which allows distributions to make this decision on their own without
the need to carry a custom patch or revert the kernel's setting in
userspace.
[edited the Kconfig help text a bit - gregkh]
Signed-off-by: Julius Werner <jwerner@chromium.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In DMA support, The received data is not pushed to tty until the DMA buffer
is filled. But some megabyte rate chips such as BT expect fast response and
data should be pushed immediately. In order to fix this issue, We suggest
the use of the timer for polling DMA buffer.
In our test, no data loss occurred at high-baudrate as compared with interrupt-
driven (We tested with 3Mbps).
We changes:
- We add timer for polling. If we set poll_timer to 10, every 10ms,
timer handler checks the residue in the dma buffer and transfer data
to the tty. Also, last_residue is updated for the next polling.
- poll_timeout is used to prevent the timer's system cost.
If poll_timeout is set to 3000 and no data is received in 3 seconds,
we inactivate poll timer and driver falls back to interrupt-driven.
When data is received again in FIFO and UART irq is occurred, we switch
back to DMA mode and start polling.
- We use consistent DMA mappings to avoid from the frequent cache operation
of the timer function for default.
- pl011_dma_rx_chars is modified. the pending size is recalculated because
data can be taken by polling.
- the polling time is adjusted if dma rx poll is enabled but no rate is
specified. Ideal polling interval to push 1 character at every interval
is the reciprocal of 'baud rate / 10 line bits per character / 1000 ms
per sec'. But It is very aggressive to system. Experimentally,
'10000000 / baud' is suitable to receive dozens of characters. the poll rate
can be specified statically by dma_rx_poll_rate of the platform data as well.
Changes compared to v1:
- Use of consistent DMA mappings.
- Added dma_rx_poll_rate in platform data to specify the polling interval.
- Added dma_rx_poll_timeout in platform data to specify the polling timeout.
Changes compared to v2:
- Use of consistent DMA mappings for default.
- Added dma_rx_poll_enable in platform data to adjust the polling time
according to the baud rate.
- remove unnecessary lock from the polling function.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For percpu notes, we are exporting only address and not size. So
the userspace tool kexec-tools is putting an upper limit of 1024
and putting the value in p_memsz and p_filesz fields. So the patch
add the new sysfile crash_notes_size to export the exact percpu
note size and let the kexec-tools parse it intead of using 1024.
The idea came from Vivek Goyal. And a later patch will be sent to
kexec-tools to let it parse the size.
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 21d8a15a (lookup_one_len: don't accept . and ..) reiserfs
started failing to delete xattrs from inode. This was due to a buggy
test for '.' and '..' in fill_with_dentries() which resulted in passing
'.' and '..' entries to lookup_one_len() in some cases. That returned
error and so we failed to iterate over all xattrs of and inode.
Fix the test in fill_with_dentries() along the lines of the one in
lookup_one_len().
Reported-by: Pawel Zawora <pzawora@gmail.com>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Until recently uio_get_minor() returned 0 for success and
a negative value on failure. This became non-negative for suceess and
negative for failure. Restore the original return value spec so that we can
successfully initialize UIO devices with a non-zero minor device
number.
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Signed-off-by: Damian Hobson-Garcia <dhobsong@igel.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If memory hot-add fails with the error -EEXIST, then this is a permanent
failure. Notify the host of this information, so the host will not attempt
hot-add again. If the failure were a transient failure, host will attempt
a hot-add after some delay.
In this version of the patch, I have added some additional comments
to clarify how the host treats different failure conditions.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Hyper-V it will be very efficient to use 2M allocations in the guest as this
makes the ballooning protocol with the host that much more efficient. Hyper-V
uses page ranges (start pfn : number of pages) to specify memory being moved
around and with 2M pages this encoding can be very efficient. However, when
memory is returned to the guest, the host does not guarantee any granularity.
To deal with this issue, split the page soon after a successful 2M allocation
so that this memory can potentially be freed as 4K pages.
If 2M allocations fail, we revert to 4K allocations.
In this version of the patch, based on the feedback from Michal Hocko
<mhocko@suse.cz>, I have added some additional commentary to the patch
description.
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This symbol will be used in the Hyper-V balloon driver to support 2M
allocations.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Windows hosts permit the guest to specify memory hot-add alignment
requirements (if any). Linux currently requires a 128MB alignment on memory
segments that can be hot-added. Specify this alignment requirement to the
host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CONFIG_PM_SLEEP to suspend/resume functions to fix the following
build warning when CONFIG_PM_SLEEP is not selected. This is because
sleep PM callbacks defined by SET_SYSTEM_SLEEP_PM_OPS are only used
when the CONFIG_PM_SLEEP is enabled.
drivers/misc/apds990x.c:1205:12: warning: 'apds990x_suspend' defined but not used [-Wunused-function]
drivers/misc/apds990x.c:1214:12: warning: 'apds990x_resume' defined but not used [-Wunused-function]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
