FMT_MPEG is for multiplexed streams, not elementary streams. The same is
true for the V4L2_CID_MPEG_VIDEO_ENCODING control.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a consequence the ioctl op has been replaced by unlocked_ioctl.
Since we are now using the core lock the locking scheme has been
simplified as well.
The main reason for converting this driver to vb2 was that the locking
scheme in v4l2.c was hopeless. It was easier to just convert the driver
then to try and salvage a threading and videobuf nightmare.
The videobuf2 framework is far, far superior compared to the old videobuf.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a consequence the ioctl op has been replaced by unlocked_ioctl.
Since we are now using the core lock the locking scheme has been
simplified as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All fields in solo_enc_fh do not belong there since they refer to global
properties. After moving all these fields to solo_enc_dev the solo_dev_fh
struct can be removed completely.
Note that this also kills the 'listener' feature of this driver. This
feature (where multiple filehandles can read the video) is illegal in the
V4L2 API. Do this in userspace: it's much more efficient to copy memory
than it is to DMA to every listener.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All fields in solo_dev_fh do not belong there since they refer to global
properties. After moving all these fields to solo_dev the solo_dev_fh
struct can be removed completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- try_fmt should never return -EBUSY.
- invalid pix->field values were not mapped to a valid value.
- the priv field of struct v4l2_pix_format wasn't zeroed.
- the try_fmt error code was not checked in set_fmt.
- enum_framesizes/intervals is valid for both MJPEG and MPEG pixel formats.
- enum_frameintervals didn't check width and height and reported the
wrong range.
- s_parm didn't set readbuffers.
- don't fail on invalid colorspace, just replace with the valid colorspace.
- bytesperline should be 0 for compressed formats.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the MOTION_THRESHOLD functionality has been temporarily reduced:
only the global threshold can be set, not the per-block. This will be
addressed in a later patch: controls are not the proper way to do this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This moves the two sirf clocksource drivers to drivers/clocksource
and integrates them into the framework for locating the clock sources
automatically.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Barry Song <Baohua.Song@csr.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
The new style ll_debug implementation for multiplatform requires the
platform glue to be in include/debug, so let's move it there to
separate the debugging logic from the platform code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Barry Song <Baohua.Song@csr.com>
Now that both irqchips for sirf are converted to not rely on
legacy domains, let's move all of the platform over to sparse
IRQ.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This updates the irqchip drier for prima2 to the current practices by
moving it into drivers/irqchip and integrating it into the irqchip_init
infrastructure. We also now use a linear irq domain as a preparation
for sparse IRQ suport.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Setup correct bus_info, let the v4l2 core set the version and add device_caps
support.
Also update the module version to 3.0.0 since this is a major upgrade.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We must not read the interrupts property manually but instead
use irq_of_parse_and_map() to guarantee that we get the correct
interrupt number once we stop using the legacy IRQ domain.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Barry Song <Baohua.Song@csr.com>
The sirf platforms use no hardcoded IRQ numbers, so there is no reason to
use the legacy domain, and by converting to the linear domain, we get
a more efficient representation of sparse IRQs and remove the dependency
on the mach/irqs.h header file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Synced to commit e9815ac5503ae60cfbf6ff8037035de8f62e2846 from
branch next in git repository https://github.com/bluecherrydvr/solo6x10.git
Only removed some code under #if LINUX_VERSION_CODE < some-kernel-version,
renamed the driver back to solo6x10 from solo6x10-edge, removed the
unnecessary compat.h header and kept the slab.h includes.
Otherwise the code is identical.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
lirc_sir uses the CONFIG_SA1100_BITSY Kconfig macro. But its Kconfig
symbol was removed in v2.4.13. So remove dead code associated with it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Case: In AdLink MPG24 there is bt878 exists (it captures one frame of all video
inputs), Video Signal for it one transmits through tw2804 chip, so we can't
control ADC (shut on/off) on tw2804, as some another can use bttv capture way.
Signed-off-by: Volokh Konstantin <volokh84@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For NUL terminated string, need always set '\0' in the end.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
version.h header inclusion is not necessary as detected by
versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using two separate tables to setup the registers for 50 or 60 hz is
better than the non-const table that is filled in at runtime.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The go7007 driver would continue during probe if no firmware could be
loaded. Without firmware the probe() should return an error, so do that.
Also move the registration of devices to the end of the probe() sequence:
once devices appear the full driver functionality should be available.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Include the patch required to add support for the go7007 to saa7134.
To be applied once the driver is moved out of staging.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The only thing missing after this to make the Sensoray model 614 board work is
to hook it up to the saa7134 driver, but that will have to wait until this
driver goes out of staging.
Signed-off-by: Pete Eberlein <pete@sensoray.com>
[hans.verkuil@cisco.com: updated to make it merge correctly]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
version.h header inclusion is not necessary as detected by
versioncheck.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Spin locks and completions are expensive in hard IRQ context and cause
problems with RT kernels. In RT kernels, both spin locks and
completions can schedule(), so we can't use them in hard irq context.
Move handling code into the irq thread function to avoid that.
Reported-by: Gregoire Gentil <gregoire@alwaysinnovating.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were printing out all the hex dumps regardless of whether dynamic
debugging was enabled or not. Now that print_hex_dump_debug() has
been implemented, we can use that instead.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't ignore dummy packets when our queues are empty. This causes dummy
packets never to be sent when traffic is not suspended by FW thresholds,
which happens only in high Tx throughput situations. This may hurt Rx
performance.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wlcore state was checked without the mutex being taken. This leads
to WARN_ONs sometimes if a notification arrives when the driver
is on, but the mutex is only taken after it is off. This usually
happens if stopping the driver while connected to a network.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the sequence number of the broadcast AP link in the wlvif. For each
connected station, save the sequence number in the drv_priv part of
ieee80211_sta. Use the saved numbers on recovery/resume, with the
obligatory increment on recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Dont use free_sta() on AP global links. It would fail an internal check
within the function and various structures within the link struct would
not be reset.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Print board type, PG with metal and ROM versions.
This might help debugging HW related issues.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For STA we report beacon loss to higher levels so that wpa_s
can attempt to roam without disconnecting. In case of P2P CLI
we don't want to attempt roaming and instead disconnect immediately
upon beacon loss.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On !CONFIG_SMP builds spin_is_locked always returns 0. Assert the
locking using assert_spin_locked, which is written to behave correctly
in all cases.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
report the average beacon rssi which is calculated
by firmware for roaming statistics instead of the
last rx packet rssi. this results a more accurate
rssi reporting
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Accumulate the total number of sent packets per-link to find out how far
the encryption sequence number has progressed. Use this number as the
initial security sequence number after recovery.
This consolidates security sequence handling for both chip families, as
we no longer have to rely on 12xx specific Tx completion.
A fortunate side effect of this is correct management of seq numbers for
AP roles and multi-role scenarios.
When a link is removed we save the last seq number on a persistent part
of the wlvif. This helps the data survive through recoveries/suspends,
which also entail changes in the hlid of the link.
This functionality is STA only currently.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The HLID of a STA can change, particularly during recovery. Don't cache
the HLID before it was potentially allocated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit 144614f3eebd7d only allowed a single active link when
turning on the optimization, ignoring the fact that an AP has two
additional global links.
Use 3 links as an indication for a single active link. Use the
FW PSM bits to verify the extra active link belongs to the AP role.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Maximum number of supported RX BA sessions depends on chip type.
wl18xx supports 5 RX BA sessions while wl12xx supports 3.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is requiered to enter sleep mode with smaller delay in forced PS mode.
This fixes issue of testing force PS mode during VoIP traffic where packets
are sent every 20ms. Chip never enters ps mode with default 30 ms delay
in such test.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
