That same USB ID is used both AF9015 and AF9035 driver.
iManufacturer is only thing we can select correct driver without a I/O.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ADC needs to be also multiplied to 2 as it9135.
Fixes bug I introduced few commits ago.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Detect automatically multiple chip versions and select configuration
according to that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for tuners integrated to the IT9135 and IT9137.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Devices on the Intel Lynxpoint Low Power Subsystem (LPSS) have
registers providing access to LTR (Latency Tolerance Reporting)
functionality that allows software to monitor and possibly influence
the aggressiveness of the platform's active-state power management.
For each LPSS device, there are two modes of operation related to LTR,
the auto mode and the software mode. In the auto mode the LTR is
set up by the platform firmware and managed by hardware. Software
can only read the LTR register values to monitor the platform's
behavior. In the software mode it is possible to use LTR to control
the extent to which the platform will use its built-in power
management features.
This changeset adds support for reading the LPSS devices' LTR
registers and exposing their values to user space for monitoring and
diagnostics purposes. It re-uses the MMIO mappings created to access
the LPSS devices' clock registers for reading the values of the LTR
registers and exposes them to user space through sysfs device
attributes. Namely, a new atrribute group, lpss_ltr, is created for
each LPSS device. It contains three new attributes: ltr_mode,
auto_ltr, sw_ltr. The value of the ltr_mode attribute reflects the
LTR mode being used at the moment (software vs auto) and the other
two contain the actual register values (raw) whose meaning depends
on the LTR mode. All of these attributes are read-only.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Devices on the Intel Lynxpoint Low Power Subsystem (LPSS) have some
common features that aren't shared with any other platform devices,
including the clock and LTR (Latency Tolerance Reporting) registers.
It is better to handle those features in common code than to bother
device drivers with doing that (I/O functionality-wise the LPSS
devices are generally compatible with other devices that don't
have those special registers and may be handled by the same drivers).
The clock registers of the LPSS devices are now taken care of by
the special clk-x86-lpss driver, but the MMIO mappings used for
accessing those registers can also be used for accessing the LTR
registers on those devices (LTR support for the Lynxpoint LPSS is
going to be added by a subsequent patch). Thus it is convenient
to add a special ACPI scan handler for the Lynxpoint LPSS devices
that will create the MMIO mappings for accessing the clock (and
LTR in the future) registers and will register the LPSS devices'
clocks, so the clk-x86-lpss driver will only need to take care of
the main Lynxpoint LPSS clock.
Introduce a special ACPI scan handler for Intel Lynxpoint LPSS
devices as described above. This also reduces overhead related to
browsing the ACPI namespace in search of the LPSS devices before the
registration of their clocks, removes some LPSS-specific (and
somewhat ugly) code from acpi_platform.c and shrinks the overall code
size slightly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
It is tuner driver for tuner integrated to the ITE IT9135 and
IT9137 chips. I split it out from the current it913x-fe driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch corrects wrongly configured parent clock for following
devices:
* Video enc/decoder
* Video ip
* Pin control
* ACP
* camx
Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com>
Reviewed-by: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some imon devices (like 15c2:0036) need a higher delay between
send_packet calls.
Default value is still 5ms to avoid regressions on already working
hardware.
Also use interruptible wait to avoid load average going too high (and
let caller handle signals).
Signed-off-by: Kevin Baradon <kevin.baradon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If no manager is connected to the vout device, the omapvid_init() function
fails. No error condition is checked, and the device is started. Later on,
when irq is serviced, a NULL pointer dereference occurs.
Also, the isr routine must be registered only if no error occurs, otherwise
the isr triggers without the proper setup, and the kernel oops again.
To prevent this, the error condition is checked, and the streamon function
exits with error. Also the isr registration call is moved after the setup
procedure is completed.
Reviewed-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If bpf_jit_enable > 1, then we dump the emitted JIT compiled image
after creation. Currently, only SPARC and PowerPC has similar output
as in the reference implementation on x86_64. Make a small helper
function in order to reduce duplicated code and make the dump output
uniform across architectures x86_64, SPARC, PPC, ARM (e.g. on ARM
flen, pass and proglen are currently not shown, but would be
interesting to know as well), also for future BPF JIT implementations
on other archs.
Cc: Mircea Gherzan <mgherzan@gmail.com>
Cc: Matt Evans <matt@ozlabs.org>
Cc: Eric Dumazet <eric.dumazet@google.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to improper condition check streaming start for some pixel
formats was prevent and the s_stream just reatuned -EINVAL.
This fixes regression introduced in commit 5565a2ad47
[media] m5mols: Protect driver data with a mutex.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mfc-encoder is not working in the latest kernel giving the
erorr "Adding control (15) failed". Adding the missing step
parameter in this control to fix the issue.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The issue was seen in VP8 decoding where the last frame was
skipped by the driver. This patch gets the correct frame_type value
to fix this bug.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Arun Mankuzhi <arun.m@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
fimc_m2m_job_finish() has to be called with the m2m context for the necessary
cleanup while resume. But currently fimc_m2m_job_finish() always passes m2m
context as NULL.
This patch preserves the context before making it null, for necessary cleanup.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gsc_m2m_job_finish() has to be called with the m2m context for the necessary
cleanup while resume. But currently gsc_m2m_job_finish() always passes m2m
context as NULL.
This patch preserves the context before making it null, for necessary cleanup.
Use gsc_m2m_opened() instead gsc_m2m_active() in gsc_resume().
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changing the variable type to 'int' from 'unsigned int'. Driver
logic expects the variable type to be 'int'.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_ctrl_new() uses check_range() for control range checking.
This function expects 'step' value for V4L2_CTRL_TYPE_BOOLEAN type control.
If 'step' value doesn't match to '1', it returns -ERANGE error.
This patch adds the default .step value to 1.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch the driver to the managed device API by replacing ioremap() calls with
devm_ioremap_resource() (that will also result in calling request_mem_region()
which the driver forgot to do until now) and k[mz]alloc() with devm_kzalloc() --
this permits to simplify driver's probe()/remove() method cleanup. We can now
remove the ioremap() error messages since the error messages are printed by
devm_ioremap_resource() itself. We can also remove the 'bitbang' field from
'struct sh_eth_private' as we don't need it anymore in order to free the memory
behind it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_drv_probe() does cast from 'void *' when assigning to the 'pd' variable
which is automatic anyway. Turn the assignment into initializer, while removing
the cast...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_mdio_init() uses the bare numbers instead of the PHY interface bits, despite
these are declared in sh_eth.h as 'enum PIR_BIT'...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I found very small bug in xc5000 source. When set option debug=1 and
listen a radio we see in dmesg xc5000: xc_SetTVStandard()
Standard = M/N-NTSC/PAL-BTSC at all times. However, it should be, instead
"FM Radio-INPUT1_MONO".
That happens because xc5000_set_radio_freq() gets the correct value for
VideoMode and AudioMode for radio and calls xc_SetTVStandard() where name
of standard comes from the incorrect place priv->video_standard.
This incorrect debug message makes debugging a little difficult.
Signed-off-by: Dmitry Belimov <d.belimov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is required by the syscall tracepoint mechanism.
Signed-off-by: Simon Marchi <simon.marchi@polymtl.ca>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
When activating syscall tracing, kernel/trace/trace_syscalls.c doesn't
find sys_call_table because it includes <asm/syscall.h>, not
<asm/syscalls.h>. Also, looking at the other architectures, that is
probably where it should be.
Signed-off-by: Simon Marchi <simon.marchi@polymtl.ca>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Looks like we have everything needed for that.
Signed-off-by: Simon Marchi <simon.marchi@polymtl.ca>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Call tracehook functions for syscall tracing.
The check for TIF_SYSCALL_TRACE was removed, because the same check is
done right before in the assembly file.
Signed-off-by: Simon Marchi <simon.marchi@polymtl.ca>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [with ptrace.h fixup]
_regmap_raw_write() contains code to call regcache_write() to write
values to the cache. That code calls memcpy() to copy the value data to
the start of the work_buf. However, at least when _regmap_raw_write() is
called from _regmap_bus_raw_write(), the value data is in the work_buf,
and this memcpy() operation may over-write part of that value data,
depending on the value of reg_bytes + pad_bytes. At least when using
reg_bytes==1 and pad_bytes==0, corruption of the value data does occur.
To solve this, remove the memcpy() operation, and modify the subsequent
.parse_val() call to parse the original value buffer directly.
At least in the case of 8-bit register address and 16-bit values, and
writes of single registers at a time, this memcpy-then-parse combination
used to cancel each-other out; for a work-buffer containing xx 89 03,
the memcpy changed it to 89 03 03, and the parse_val changed it back to
89 89 03, thus leaving the value uncorrupted. This appears completely
accidental though. Since commit 8a819ff "regmap: core: Split out in
place value parsing", .parse_val only returns the parsed value, and does
not modify the buffer, and hence does not (accidentally) undo the
corruption caused by memcpy(). This caused bogus values to get written
to HW, thus preventing e.g. audio playback on systems with a WM8903
CODEC. This patch fixes that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The packetsocket fanout test uses a packet ring. Use TPACKET_V2
instead of TPACKET_V1 to work around a known 32/64 bit issue in
the older ring that manifests on sparc64.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If pin_free is called on a pin already freed, mux_usecount is set to
UINT_MAX which is really a bad idea.
This will issue a warning, so that we can correct the code responsible
for the double free.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PHY layer no longer returns NULL, we must
switch from IS_ERR_OR_NULL() to IS_ERR().
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ASoC does not yet really have the framework features needed to
support propagating sample rates through the device well yet implement
basic support for the ISRCs equivalent to that we currently have for the
ASRCs. The user can opt for 8kHz or 16kHz as the rate for the DSP blocks
in addition to the main audio rate, these being the primary use cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the device state does not diverge from the state we have set
in the register map in order to make the behaviour clearer.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some system designs have been identified which repurpose portions of the
speaker driver circuits for other functions which will require that they
not be managed using DAPM. Prepare for this by factoring out the creation
of the speaker widgets into the core driver, the widgets will be replaced
by dummy ones when the additional functions are enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a minor bug (probably due to a typo) while checking
the SoC specific controls in mvebu_pinctrl_probe().
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We've had several reports of people attempting to mount Windows 8 shares
and getting failures with a return code of -EINVAL. The default sec=
mode changed recently to sec=ntlmssp. With that, we expect and parse a
SPNEGO blob from the server in the NEGOTIATE reply.
The current decode_negTokenInit function first parses all of the
mechTypes and then tries to parse the rest of the negTokenInit reply.
The parser however currently expects a mechListMIC or nothing to follow the
mechTypes, but Windows 8 puts a mechToken field there instead to carry
some info for the new NegoEx stuff.
In practice, we don't do anything with the fields after the mechTypes
anyway so I don't see any real benefit in continuing to parse them.
This patch just has the kernel ignore the fields after the mechTypes.
We'll probably need to reinstate some of this if we ever want to support
NegoEx.
Reported-by: Jason Burgess <jason@jacknife2.dns2go.com>
Reported-by: Yan Li <elliot.li.tech@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
This patch implements the AArch64-specific atomic bitops functions using
exclusive memory accesses to avoid locking.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch introduces AArch64-specific memory functions (memcpy,
memmove, memchr, memset). These functions are not optimised for any CPU
implementation but can be used as a starting point once hardware is
available.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Release v2.6.30 removed the MT9M001_PCA9536_SWITCH and
MT9V022_PCA9536_SWITCH Kconfig symbols, in commits
36034dc325 ("V4L/DVB (11032): mt9m001:
allow setting of bus width from board code") and
e958e27ade ("V4L/DVB (11033): mt9v022:
allow setting of bus width from board code").
These two commits removed all gpio related code from these two drivers.
But they skipped removing their two selects of GPIO_PCA953X. Remove
these now as they are outdated. Their dependencies can never evaluate to
true anyhow.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
