Core & protocols
----------------
- A few steps lowering rtnl_lock dependence:
- per-netns netdev unregistration for select SW drivers
(e.g. veth, ipvlan, tunnels)
- rtnl_lock-less FIB rule changes (RTM_NEWRULE and RTM_DELRULE)
- prepare software drivers and TC qdiscs for rtnl_lock-less GET
- Support BIG TCP (>64kB TSO) in UDP tunnels (vxlan, geneve).
- Support buffers larger than PAGE_SIZE in devmem zero-copy API.
- Improve MPTCP handling of extreme memory pressure handling,
when out-of-order queue had to be pruned.
- Report the per-group user count via RTM_GETMULTICAST.
- Expose the route deletion reason in RTM_DELROUTE.
- Add a SO_RIGHTS_NOTRUNC option to UNIX sockets to enable more useful
handling of LSM denials when receiving SCM_RIGHTS messages: instead
of truncating the message at the first blocked fd, keep every fd slot
and store the LSM errno in the blocked slot.
- IPv6 Segment Routing - support looking up the post-encap SID
(address) in a different/specified routing table.
- Support PRP RedBox (interlink) creation.
- Support per-nexthop UDP dst port in VXLAN.
- Continue converting getsockopt callbacks in a number of protocols
to iov_iter.
Ethernet
--------
- Marge initial CXL support for AMD/Solarflare NICs (shared branch
with the CXL tree).
- New drivers:
- ADIN1140 10BASE-T1S MACPHY
- Initial skeleton of Intel iXD and ZTE Dinghai drivers.
- High-speed NICs:
- AMD/Pensando:
- support firmware flashing
- Cisco (enic):
- SR-IOV V2 admin channel and MBOX protocol
- Huawei (hns3):
- support for ethtool pfc_prevention_tout
- nVidia/Mellanox:
- support sharing bandwidth control across interfaces of
the same device
- Marvell (octeontx2-pf):
- link RQ page pools to netdev for Netlink stats
- Google vNIC:
- XDP metadata support for DQ RDA
- Microsoft vNIC:
- support forcing full-page RX buffers
- Other NICs:
- Synopsys IP:
- eic7700: support for eth1
- Microchip (lan743x):
- support for RMII interface
- Wangxun:
- support for ethtool -G and -C for VFs
- add Tx timeout and PCIe error handling
- Intel (igb/igc):
- RSS key get/set support
- support for forcing link speed without auto-negotiation
- Switches:
- NXP (dpaa2):
- support bonding/LAG offload
- Mediatek:
- mt7530: EN7528 support
- initial support for MT7628
- Micrel (ksz8/9):
- refactoring work to move towards library model
- PTP support for KSZ8463
- nVidia/Mellanox:
- support rtnl-lock-less ethtool callbacks
- Realtek:
- rtl8366rb: use generic RTL83xx code
- support SGMII and HSGMII for RTL8367S
- PHYs:
- Airoha:
- EcoNet EN7528 PHY support
- DAPU Telecom
- DAPU Telecom DAP8211R(I) Gigabit PHY support
- Realtek:
- support RTL8261C_CG
- support RTL8261D
Wireless
--------
- nl80211: per-link statistics support for multi-link operation
- mac80211: AQL/airtime-fairness support for multicast
- Merge Peripheral Authentication Service (PAS) / TEE support
for ath12k (shared branch with the firmware/qcom tree).
- New drivers:
- mm81x for Morse Micro Long-Range S1G devices
- nxpwifi for NXP devices (mostly forked off from mwifiex)
- Driver changes:
- Broadcom (brcmfmac):
- DPP support, some Cypress part update
- MediaTek (mt76):
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- Qualcomm (ath12k):
- much kernel infrastructure integration work
- AHB platform MultiPD support
- Realtek (rt89):
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- Intel:
- new FW version support
Bluetooth
---------
- HCI: add support for Shorter Connection Interval (SCI) feature.
- af_bluetooth: add minimal context analysis annotations.
- Driver changes:
- Intel:
- add Bluetooth SAR revision 2 support
- add vendor_reset PCI sysfs for PLDR
- Mediatek:
- add USB IDs for MT7902 and MT7922 devices
- Realtek:
- add USB IDs for 8761CU and 8852BE devices
- NXP:
- add M.2 Bluetooth device support using pwrseq
Misc
----
- DPLL support for manual/numerical oscillator control (NCO)
(implement in zl3073x).
- MCTP support for MCTP over USB v1.1 (DMTF DSP0283).
- Power-over-Ethernet: support Realtek PSE controllers.
- Remove the IBM EHEA driver.
- Remove tulip/xircom_cb driver.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=zDto
-----END PGP SIGNATURE-----
Merge tag 'net-next-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"One of the 'small improvements all over the place' releases for us.
It's hard to draw any direct comparisons because summer vacations
disrupted our patch processing (and presumably - generation) quite a
bit.
Quick and dirty count suggests we (Paolo and I) merged a very similar
number of net (632) and net-next (648) patches. This is not telling
the full story either because 1/3 to 1/2 of the net-next patches also
*seem* like AI-driven low priority fixes, cleanups and clarifications.
We are completely overwhelmed, of course. The glimmer of hope is that
we secured sufficient LLM budget and access (thank you Meta!) to run
reviews with multiple frontier models on each patch. This eliminates
some hallucinations. That said, in terms of review, the LLMs can only
do so much.
The sad truth is that our APIs (especially for rare events like PCIe
errors, timeouts etc) have always been racy, and now LLMs don't let us
ignore that. I expect our direction for the next release will be to
tweak the reviews a little bit more, but start shifting focus to
letting the LLMs take care of the busy work - managing patchwork,
automating common process complaints, editing commit messages, and
maybe applying patches which already got "reviewed-by" tags from
people we trust...
Core & protocols:
- A few steps lowering rtnl_lock dependence:
- per-netns netdev unregistration for select SW drivers (e.g.
veth, ipvlan, tunnels)
- rtnl_lock-less FIB rule changes (RTM_NEWRULE and RTM_DELRULE)
- prepare software drivers and TC qdiscs for rtnl_lock-less GET
- Support BIG TCP (>64kB TSO) in UDP tunnels (vxlan, geneve)
- Support buffers larger than PAGE_SIZE in devmem zero-copy API
- Improve MPTCP handling of extreme memory pressure handling, when
out-of-order queue had to be pruned
- Report the per-group user count via RTM_GETMULTICAST
- Expose the route deletion reason in RTM_DELROUTE
- Add a SO_RIGHTS_NOTRUNC option to UNIX sockets to enable more
useful handling of LSM denials when receiving SCM_RIGHTS messages:
instead of truncating the message at the first blocked fd, keep
every fd slot and store the LSM errno in the blocked slot
- IPv6 Segment Routing - support looking up the post-encap SID
(address) in a different/specified routing table
- Support PRP RedBox (interlink) creation
- Support per-nexthop UDP dst port in VXLAN
- Continue converting getsockopt callbacks in a number of protocols
to iov_iter
Ethernet:
- Merge initial CXL support for AMD/Solarflare NICs (shared branch
with the CXL tree)
- New drivers:
- ADIN1140 10BASE-T1S MACPHY
- Initial skeleton of Intel iXD and ZTE Dinghai drivers
- High-speed NICs:
- AMD/Pensando:
- support firmware flashing
- Cisco (enic):
- SR-IOV V2 admin channel and MBOX protocol
- Huawei (hns3):
- support for ethtool pfc_prevention_tout
- nVidia/Mellanox:
- support sharing bandwidth control across interfaces
of the same device
- Marvell (octeontx2-pf):
- link RQ page pools to netdev for Netlink stats
- Google vNIC:
- XDP metadata support for DQ RDA
- Microsoft vNIC:
- support forcing full-page RX buffers
- Other NICs:
- Synopsys IP:
- eic7700: support for eth1
- Microchip (lan743x):
- support for RMII interface
- Wangxun:
- support for ethtool -G and -C for VFs
- add Tx timeout and PCIe error handling
- Intel (igb/igc):
- RSS key get/set support
- support for forcing link speed without auto-negotiation
- Switches:
- NXP (dpaa2):
- support bonding/LAG offload
- Mediatek:
- mt7530: EN7528 support
- initial support for MT7628
- Micrel (ksz8/9):
- refactoring work to move towards library model
- PTP support for KSZ8463
- nVidia/Mellanox:
- support rtnl-lock-less ethtool callbacks
- Realtek:
- rtl8366rb: use generic RTL83xx code
- support SGMII and HSGMII for RTL8367S
- PHYs:
- Airoha:
- EcoNet EN7528 PHY support
- DAPU Telecom
- DAPU Telecom DAP8211R(I) Gigabit PHY support
- Realtek:
- support RTL8261C_CG
- support RTL8261D
Wireless:
- nl80211: per-link statistics support for multi-link operation
- mac80211: AQL/airtime-fairness support for multicast
- Merge Peripheral Authentication Service (PAS) / TEE support for
ath12k (shared branch with the firmware/qcom tree)
- New drivers:
- mm81x for Morse Micro Long-Range S1G devices
- nxpwifi for NXP devices (mostly forked off from mwifiex)
- Driver changes:
- Broadcom (brcmfmac):
- DPP support, some Cypress part update
- MediaTek (mt76):
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- Qualcomm (ath12k):
- much kernel infrastructure integration work
- AHB platform MultiPD support
- Realtek (rt89):
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- Intel:
- new FW version support
Bluetooth:
- HCI: add support for Shorter Connection Interval (SCI) feature
- af_bluetooth: add minimal context analysis annotations
- Driver changes:
- Intel:
- add Bluetooth SAR revision 2 support
- add vendor_reset PCI sysfs for PLDR
- Mediatek:
- add USB IDs for MT7902 and MT7922 devices
- Realtek:
- add USB IDs for 8761CU and 8852BE devices
- NXP:
- add M.2 Bluetooth device support using pwrseq
Misc:
- DPLL support for manual/numerical oscillator control (NCO)
(implement in zl3073x)
- MCTP support for MCTP over USB v1.1 (DMTF DSP0283)
- Power-over-Ethernet: support Realtek PSE controllers
- Remove the IBM EHEA driver
- Remove tulip/xircom_cb driver"
* tag 'net-next-7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1433 commits)
net/mlx5e: do not HW-GRO coalesce small frames
net: openvswitch: fix nf_connlabels leak in ovs_ct_init
net: add missing ref_tracker_dir_exit() to alloc_netdev_mqs()
net: openvswitch: fix flow mask use-after-free on flow deletion
sctp: stop processing a packet once its association is deleted
dpll: zl3073x: add PTP clock support
dpll: zl3073x: add channel ToD, phase step and TIE operations
dpll: zl3073x: scale poll interval proportionally to timeout
ptp: vmclock: prevent read-only mappings from becoming writable
ipv4: reject undersized MTUs in ip_do_fragment()
bonding: initialize err for empty target lists
net: dsa: initial support for MT7628 embedded switch
net: dsa: initial MT7628 tagging driver
net: phy: mediatek: add phy driver for MT7628 built-in Fast Ethernet PHYs
dt-bindings: net: dsa: add MT7628 ESW
net: pse-pd: realtek-pse-mcu: add UART transport
net: pse-pd: realtek-pse-mcu: add I2C transport
net: pse-pd: add Realtek PSE MCU core
dt-bindings: net: pse-pd: add bindings for Realtek PSE MCU
vsock: use sock_error() to consume sk_err after a failed connect
...
- ARM SMMUv2:
- Device-tree binding updates for Qualcomm Eliza, Maili, Shikra and
IPQ9650 SoCs.
- Add support for Qualcomm SM8450.
- Numerous fixes for lifetime and ordering issues found by Sashiko in
the Qualcomm driver.
- ARM SMMUv3:
- Fix interrupt type in device-tree binding example for NVIDIA CMDQV.
- Numerous fixes for issues identified by Sashiko in the NVIDIA CMDQV
driver.
- Work around TLB erratum T264-SMMU-3 on Tegra264 by repeating the
invalidation sequence.
- Add support for HAFT (hardware access flag in table entries) when
using SVA.
- Probe for 52-bit addressing with a page size smaller than 64k ('DS')
but don't do anything with it for now.
- Minor driver improvements (remove sort_nonatomic(), use
readl_relaxed_poll_timeout_atomic(), fix IOPF teardown ordering).
- Intel VT-d:
- Consolidation of complex enablement logic into a clean, priority-based
state machine.
- Support for the DMA_REMAP_OPT_OUT flag from the VT-d v5.2
specification.
- An update to cache_tag_flush_devtlb_psi() to use full-range constants
instead of modifying shared variables for CACHE_TAG_NESTING_DEVTLB.
- A fix for the UCTP context-table slot when copying root entries.
- Fixes for several pre-existing issues reported by Sashiko.
- General code cleanup and refinement.
- AMD IOMMU:
- Add SNP page-mode-0 support, enabling passthrough, v2 DMA page
tables and host SVA on supporting systems.
- Fix invalid PPR handling, COMPLETE_PPR responses and guest-mode
reporting.
- Improve Southbridge IOAPIC validation and remove the dependency on
hard-coded device IDs.
- Fix PCI-device lifetime, debugfs and diagnostic issues.
- IOMMU core and IOMMUFD:
- Restore serialization of the shared MSI-page list.
- Fix SVA-handle publication and several IOMMUFD reference and error
path leaks.
- Return the expected zero result for invalid generic page-table
translations.
- Allocate per-CPU IOVA magazines lazily to reduce memory use on
large systems.
- PCI ATS:
- Make VF support checks account for the associated PF and validate
that VF and PF Smallest Translation Unit settings agree.
- Platform drivers:
- Fix Qualcomm runtime-PM, probe unwind, fault reporting and page
table initialization races.
- Rework Rockchip state handling and fix clock, probe and stale-fault
handling.
- Fix smaller issues in the MSM and MediaTek drivers.
- Device-tree bindings:
- Add new Qualcomm SMMU compatibles, convert the OMAP IOMMU binding
to YAML, and fix the Tegra264 CMDQV interrupt example.
- Various smaller cleanups, documentation fixes and a Rust IOMMU
safety/readability improvement.
-----BEGIN PGP SIGNATURE-----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=V5FT
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Joerg Roedel:
"ARM SMMUv2:
- Device-tree binding updates for Qualcomm Eliza, Maili, Shikra and
IPQ9650 SoCs
- Add support for Qualcomm SM8450
- Numerous fixes for lifetime and ordering issues found by Sashiko in
the Qualcomm driver
ARM SMMUv3:
- Fix interrupt type in device-tree binding example for NVIDIA CMDQV
- Numerous fixes for issues identified by Sashiko in the NVIDIA CMDQV
driver
- Work around TLB erratum T264-SMMU-3 on Tegra264 by repeating the
invalidation sequence
- Add support for HAFT (hardware access flag in table entries) when
using SVA
- Probe for 52-bit addressing with a page size smaller than 64k
('DS') but don't do anything with it for now
- Minor driver improvements (remove sort_nonatomic(), use
readl_relaxed_poll_timeout_atomic(), fix IOPF teardown ordering)
Intel VT-d:
- Consolidation of complex enablement logic into a clean,
priority-based state machine
- Support for the DMA_REMAP_OPT_OUT flag from the VT-d v5.2
specification
- An update to cache_tag_flush_devtlb_psi() to use full-range
constants instead of modifying shared variables for
CACHE_TAG_NESTING_DEVTLB
- A fix for the UCTP context-table slot when copying root entries
- Fixes for several pre-existing issues reported by Sashiko
- General code cleanup and refinement
AMD IOMMU:
- Add SNP page-mode-0 support, enabling passthrough, v2 DMA page
tables and host SVA on supporting systems
- Fix invalid PPR handling, COMPLETE_PPR responses and guest-mode
reporting
- Improve Southbridge IOAPIC validation and remove the dependency on
hard-coded device IDs
- Fix PCI-device lifetime, debugfs and diagnostic issues
IOMMU core and IOMMUFD:
- Restore serialization of the shared MSI-page list
- Fix SVA-handle publication and several IOMMUFD reference and error
path leaks
- Return the expected zero result for invalid generic page-table
translations
- Allocate per-CPU IOVA magazines lazily to reduce memory use on
large systems
PCI ATS:
- Make VF support checks account for the associated PF and validate
that VF and PF Smallest Translation Unit settings agree
Platform drivers:
- Fix Qualcomm runtime-PM, probe unwind, fault reporting and page
table initialization races
- Rework Rockchip state handling and fix clock, probe and stale-fault
handling
- Fix smaller issues in the MSM and MediaTek drivers
Device-tree bindings:
- Add new Qualcomm SMMU compatibles, convert the OMAP IOMMU binding
to YAML, and fix the Tegra264 CMDQV interrupt example
Various smaller cleanups, documentation fixes and a Rust IOMMU
safety/readability improvement"
* tag 'iommu-updates-v7.3' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (93 commits)
iommu/amd: Add SNP page mode 0 support
iommu/amd: Fix GN bit setting in COMPLETE_PPR_REQUEST command
iommu/amd: Rate limit INVALID_PPR_REQUEST error logging
iommu/amd: Fix missing CMD_COMPLETE_PPR response for invalid PPR requests
iommu/amd: Introduce PPR_TAG_LAST_PAGE() macro
iommu/amd: Fix incorrect device ID in invalid PASID error message
iommu/vt-d: Flush context cache with correct SID when tearing down aliases
iommu/vt-d: Tear down scalable-mode context on probe failure
iommu/vt-d: Fix iopf_refcount leak on RID domain replacement
iommu/vt-d: Clear Present bit before tearing down copied context entry
iommu/vt-d: Fix copied_tables bitmap leak on error in copy_translation_tables
iommu/vt-d: Cache max domain ID to avoid redundant calculation
iommu/vt-d: Support the new DMA_REMAP_OPT_OUT flag bit
iommu/vt-d: Remove dmar_disabled
iommu/vt-d: Remove the 'force_on' variable
iommu/vt-d: Call dmar_can_force_on() for tboot opt-in
iommu/vt-d: Use dmar_can_force_on() for platform opt-in
iommu/vt-d: Consolidate dmar policy management and force_on logic
iommu/vt-d: Remove dead code when CONFIG_INTEL_IOMMU is not set
iommu/vt-d: Force requesting ACS when tboot is enabled
...
Merge updates related to the ACPI video bus driver for 7.3-rc1:
- Introduce helper function acpi_dev_is_video_device() and use it in
the core ACPI device enumeration code, in the ACPI video bus driver,
in the ACPI support code for I2C, in the PCI VGA driver, and in the
x86 platform thinkpad_acpi driver (Andy Shevchenko)
- Add a quirk to use the native backlight on Acer Nitro AN515-46 to the
ACPI video bus driver (Marcos Paulo Medeiros)
- Release PCI device reference after lookup in video_detect_portege_r100()
in the ACPI video bus driver (Yuho Choi)
* acpi-video:
ACPI: video: Release PCI device reference after lookup
ACPI: video: force native backlight on Acer Nitro AN515-46
platform/x86: thinkpad_acpi: Convert to use acpi_dev_is_video_device() helper
PCI/VGA: Convert to use acpi_dev_is_video_device() helper
i2c: acpi: Convert to use acpi_dev_is_video_device() helper
ACPI: video: Convert to use acpi_dev_is_video_device() helper
ACPI: scan: Convert to use acpi_dev_is_video_device() helper
ACPI: utils: Introduce acpi_dev_is_video_device() helper
- iwlwifi: new FW version support
- mt76:
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- rtw89:
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- ath12k: AHB platform MultiPD support
- cfg80211: pre-assign cookies for operations
- mac80211: AQL support for multicast
-----BEGIN PGP SIGNATURE-----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=L5q1
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2026-08-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
Quite a bunch more work, of note:
- iwlwifi: new FW version support
- mt76:
- mt7928 support
- mt7925 NAN support
- mt7996 AP powersave improvements
- rtw89:
- LED support
- RTL8922DE support
- dual-BT coex for RTL8922D
- ath12k: AHB platform MultiPD support
- cfg80211: pre-assign cookies for operations
- mac80211: AQL support for multicast
* tag 'wireless-next-2026-08-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (403 commits)
wifi: nxpwifi: bound uAP association event IEs to the event buffer
wifi: nxpwifi: detach sync command buffer on interrupted wait
wifi: brcmfmac: Fix memory leak in brcmf_sdio_read_control()
wifi: rsi: Fix types to appease CFI
wifi: mac80211: skip default WMM setup for AP_VLAN links
wifi: nxpwifi: fix multiple static analysis errors and warnings
wifi: morsemicro: MM81X should be invisible and selected by its users
wifi: nxp: NXPWIFI should be invisible and selected by its users
wifi: cfg80211: stop PMSR before P2P and NAN teardown
wifi: mac80211: disconnect on CSA to channel 0
wifi: brcmfmac: fix P2P action frame handling without device vif
wifi: brcmfmac: Set DMA direction for msgbuf packet IDs
wifi: brcmfmac: validate msgbuf flowring IDs before use
wifi: mac80211: fix RCU usage in peer probing
wifi: mac80211: fix RCU dereference in throughput estimate
wifi: wilc1000: validate monitor transmit frame headers
wifi: mac80211: skip unused probe response countdown offsets
wifi: zd1211rw: reject secondary interfaces to prevent conflicts
wifi: nl80211: clean up color-change beacon data on errors
wifi: mac80211: send TWT teardown to peer after setup TX failure
...
====================
Link: https://patch.msgid.link/20260806121304.190084-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some random cleanups and fixes on rtlwifi, rtw88 and rtw89. The major
features added to rtw89 are listed:
rtw89:
- add LED support
- update BT-coexistence mechanism to support dual Bluetooth for RTL8922D
- support WiFi 7 chip RTL8922DE
-----BEGIN PGP SIGNATURE-----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=8EO5
-----END PGP SIGNATURE-----
Merge tag 'rtw-next-2026-08-02' of https://github.com/pkshih/rtw
Ping-Ke Shih says:
==================
rtw-next patches for v7.3
Some random cleanups and fixes on rtlwifi, rtw88 and rtw89. The major
features added to rtw89 are listed:
rtw89:
- add LED support
- update BT-coexistence mechanism to support dual Bluetooth for RTL8922D
- support WiFi 7 chip RTL8922DE
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmpsv30UHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vx05BAAlX0ggF2vDuKKQK1Q67oBANG+ANZq
wAyMibleGWHvUfknsxcioGoXr+oZrI2fbuvaz1id2Tlx3vByfYiSihrNz4BrDbny
H+YD2Mqhz0aaanb+G1WEqRndCyRLtYmsr0cUAp7giBh22t43tgdIBvKr2PsCsKCo
WiEUP/QvxYuiJ73g6s7RqbwIYSzk/9MMSDhoO83c/gRZcY/r47KY19ysLevQ/176
h0xC73EV6UF0dqe485jt24/zzYkN70zV3FscPMLkU7s0Fd2jzRm/zktS7tbLTUg2
PZwqCnHc4dytoqEmcycrQHGNiPRQCCOnqcsSlWcMzPPBdYCR1EUictiYXgq0Bd4T
EvvjHHl3/9IVCWgkz7rKmLz8V7GWoJSH11Ykh3AWWc7roFsTn1UH2YY+85/Asfv+
/vuo2G7zskKE5WOSaEOLBvYi84FRge3FxA3XPgMYTOePTqIpjjJ6eglZRmxEhid5
IrJhaB0O9kNuRR3Nu85lgHqL35Pp5AUVOLqyXELvcbBBJHtm1PTgjAZjyRIm0Rn7
YINhuQr3gw+3vKaXGB8qHqXMG1/hdMkHH9t6LEqAqFtRrTZjzquGg5oFnJOYINCL
VinNH6/G1qIYBThTVDMeVSTUqCbkz97eedzyGo92oqpUdhseWyaaV4vwW1ss4DWv
QSN25brLKheYiKk=
=YyK4
-----END PGP SIGNATURE-----
Merge tag 'pci-v7.2-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Remove Karthikeyan Mitran from Mobiveil MAINTAINERS PCIe entry since
email bounces (Manivannan Sadhasivam)
- Preserve i.MX6Q, i.MX6QP, and i.MX6SX Root Port MSI/MSI-X
Capabilities when using iMSI-RX to work around hardware defect
(Soeren Moch)
- Reorder i.MX6Q/DL PHY power up to fix boot hang regression (Richard
Zhu)
* tag 'pci-v7.2-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI: imx6: Fix i.MX6Q/DL boot hang caused by improper PHY power sequencing
PCI: imx6: Keep i.MX6 Root Port MSI/MSI-X Capabilities with iMSI-RX to work around hardware bug
MAINTAINERS: Drop Karthikeyan Mitran from Mobiveil PCIe entry
commit 610fa91d98 ("PCI: imx6: Assert PERST# before enabling regulators")
introduced a boot hang on i.MX6Q/DL variants by reordering
imx_pcie_host_init() to call imx6q_pcie_enable_ref_clk() (which powered up
the PHY) before imx6q_pcie_core_reset() (which powered it back down).
Before 610fa91d98, the sequence was:
1. imx_pcie_assert_core_reset() - power down PHY (set TEST_PD), set
REF_CLK_EN
2. imx_pcie_clk_enable() - power up PHY (clear TEST_PD), set REF_CLK_EN
3. Link training starts with PHY powered up (TEST_PD cleared)
4. Link training succeeds
After 610fa91d98, the sequence became:
1. imx_pcie_clk_enable() - power up PHY (clear TEST_PD), set REF_CLK_EN
2. imx_pcie_assert_core_reset() - power down PHY (set TEST_PD), set
REF_CLK_EN
3. imx_pcie_deassert_core_reset() - does nothing
4. Link training starts with PHY powered down (TEST_PD set)
5. Link training fails and boot hangs when PHY register accesses hang
To fix this:
- Remove TEST_PD PHY power control from imx6q_pcie_enable_ref_clk()
- Remove REF_CLK_EN control from imx6q_pcie_core_reset()
- Add TEST_PD PHY power control to imx6qp_pcie_core_reset(), which
previously relied on imx6q_pcie_enable_ref_clk() to power up the PHY by
clearing TEST_PD
- Clear TEST_PD to power on PHY in imx_pcie_deassert_core_reset()
These changes together ensure the correct sequence:
1. REF_CLK_EN set in clk_enable() (TEST_PD untouched)
2. TEST_PD set in assert_core_reset() (PHY power off)
3. TEST_PD cleared in deassert_core_reset() (PHY power on)
4. Link training starts with proper PHY state
The i.MX6Q/DL PCIe PHY requires approximately 120us between TEST_PD
de-assertion and link training start. Add usleep_range(200, 500) in
imx6q_pcie_core_reset() after clearing TEST_PD to satisfy this requirement.
Add explicit imx_pcie_assert_core_reset() calls in error paths and
host_exit() to ensure no power leak.
Fixes: 610fa91d98 ("PCI: imx6: Assert PERST# before enabling regulators")
Reported-by: Leonardo Costa <leoreis.costa@gmail.com>
Closes: https://lore.kernel.org/lkml/20260629143439.361560-1-leoreis.costa@gmail.com/
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Leonardo Costa <leonardo.costa@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20260728035159.2702021-1-hongxing.zhu@oss.nxp.com
Move the vendor and device ID for the existing Spacemit K1 PCIe Root
Complex to include/linux/pci_ids.h. Also add K3's Root Complex device ID
to this header. This is done so that these values can be referenced in
the rtw89 driver to enable 36-bit DMA ability in it for WiFi to function
on the K3 Pico ITX board.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Anirudh Srinivasan <asrinivasan@oss.tenstorrent.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20260716-rtw89-spacemit-k3-v2-1-392b577ebf75@oss.tenstorrent.com
Merge the introduction of acpi_dev_is_video_device() along with some
following driver updates related to it (from Andy Shevchenko).
* acpi-video:
platform/x86: thinkpad_acpi: Convert to use acpi_dev_is_video_device() helper
PCI/VGA: Convert to use acpi_dev_is_video_device() helper
i2c: acpi: Convert to use acpi_dev_is_video_device() helper
ACPI: video: Convert to use acpi_dev_is_video_device() helper
ACPI: scan: Convert to use acpi_dev_is_video_device() helper
ACPI: utils: Introduce acpi_dev_is_video_device() helper
On some NXP chipsets, disabling Root Port MSI/MSI-X Capabilities blocks
MSIs originating from Endpoints from reaching the iMSI-RX controller.
To address this hardware bug, commit 3a4e8302e7 ("PCI: imx6: Keep Root
Port MSI capability with iMSI-RX to work around hardware bug") preserves
Root Port MSI and MSI-X Capabilities on i.MX7D, i.MX8MM, and i.MX8MQ
when iMSI-RX is in use.
The same applies to i.MX6Q, i.MX6QP, and i.MX6SX, so preserve Root Port
MSI/MSI-X Capabilities there as well.
Note that preserving these Capabilities means Root Port-originated MSIs
such as AER and PME won't be received due to separate hardware limitations.
Users may need to use workarounds such as passing the 'pcie_pme=nomsi'
command-line parameter.
Fixes: f5cd8a929c ("PCI: dwc: Remove MSI/MSIX capability for Root Port if iMSI-RX is used as MSI controller")
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: stable@vger.kernel.org # 7.0+
Link: https://patch.msgid.link/20260717033203.2965045-1-hongxing.zhu@oss.nxp.com
While every PCI Function that implements ATS has an independent ATS
Extended Capability structure with a Read/Write Smallest Translation
Unit (STU) field, the kernel manages SR-IOV ATS by requiring the IOMMU
driver to configure the STU on the Physical Function (PF) before any
any Virtual Functions (VFs) are created.
Currently, pci_prepare_ats() bails out early for VFs, assuming that the
PF has already been correctly prepared. However, this creates a potential
mismatch if a VF is subsequently prepared with a different page shift.
Update pci_prepare_ats() to validate that the requested page shift (ps)
matches the STU already configured in the associated PF. This ensures
early detection of incompatible configurations and maintains the kernel's
policy of consistent STU sizing across all functions associated with a
given SMMU.
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Samiullah Khawaja <skhawaja@google.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Pranjal Shrivastava <praan@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Update pci_ats_supported() to additionally check the associated PF's
status when called on a VF. This ensures that PF-level quirks and
untrusted status are correctly propagated to VFs, providing a robust
support check that aligns with the kernel's PF-centric ATS configuration
model and is immune to the timing of VF-specific fixups.
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Samiullah Khawaja <skhawaja@google.com>
Reviewed-by: Nicolin Chen <nicolinc@nvidia.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Pranjal Shrivastava <praan@google.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Replace the #include of <linux/mod_devicetable.h> by the more specific
<linux/device-id/*.h> where applicable. For most cases the include
can be dropped completely, only a few drivers need one or two headers
added.
Acked-by: Danilo Krummrich <dakr@kernel.org>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/1a3f2007c5c5dcf555c09a4035ce3ae8ef1b6c49.1782808461.git.u.kleine-koenig@baylibre.com
Signed-off-by: Uwe Kleine-König (The Capable Hub) <u.kleine-koenig@baylibre.com>
-----BEGIN PGP SIGNATURE-----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=h+xD
-----END PGP SIGNATURE-----
Merge tag 'pci-v7.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Remove MPS/MRRS Kconfig settings (CONFIG_PCIE_BUS_*) that worked
around a WiFi device defect; use a quirk or boot-time
"pci=pcie_bus_tune_*" kernel parameter instead (Bjorn Helgaas)
- Always lift 2.5GT/s restriction in PCIe failed link retraining to
avoid clamping a link to 2.5GT/s after hot-plug changes the device
(Maciej W. Rozycki)
- Request bus reassignment when not probe-only to fix an enumeration
regression on Marvell CN106XX and possibly other DT-based systems
(Ratheesh Kannoth)
- Fix procfs race between pci_proc_init() and pci_bus_add_device()
that resulted in 'proc_dir_entry ... already registered' warnings
and pointer corruption (Krzysztof Wilczyński)
- Fix sysfs race that causes 'duplicate filename' warnings and boot
panics by converting PCI resource files to static attributes
(Krzysztof Wilczyński)
- Expose sysfs 'resourceN_resize' attributes only on platforms with
PCI mmap (Krzysztof Wilczyński)
- Require CAP_SYS_ADMIN to write to sysfs 'resourceN_resize'
attributes (Krzysztof Wilczyński)
- Add security_locked_down(LOCKDOWN_PCI_ACCESS) to alpha PCI resource
mmap path to match the generic path (Krzysztof Wilczyński)
- Use kstrtobool() to parse the 'rom' attribute input to avoid the
unexpected behavior of enabling the ROM when writing '0' with no
trailing newline (Krzysztof Wilczyński)
Resource management:
- Improve resource claim logging for debuggability (Ilpo Järvinen)
- Clean up several uses of const parameters (Ilpo Järvinen)
- Check option ROM header signatures and lengths before accessing to
avoid page faults and alignment faults (Guixin Liu)
ASPM:
- Don't reconfigure ASPM when entering low-power D-state; only do it
when returning back to D0 (Carlos Bilbao)
Power management:
- During suspend, set power state to 'unknown' for all devices, not
just those with drivers (Lukas Wunner)
- Skip restoring Resizable BARs and VF Resizable BARs if device
doesn't respond to config reads, to avoid invalid array accesses
(Marco Nenciarini)
- Add pci_suspend_retains_context() so drivers can tell whether
devices retain internal state across suspend/resume, since some
platforms reset devices on suspend; use this in nvme to avoid
issues on Qcom RCs (Manivannan Sadhasivam)
Power control:
- Only to power on/off devices that actually support power control to
avoid poking at incompatible devices mentioned in DT (Manivannan
Sadhasivam)
Virtualization and resets:
- Log device readiness timeouts as errors, not warnings, because the
device is likely unusable in this case (Bjorn Helgaas)
- Wait for device readiness after soft reset (D3hot ->
D0uninitialized transition), when the device may respond with
Request Retry Status (RRS) if it needs more time to initialize
(Bjorn Helgaas)
- Drop unnecessary retries when restoring BARs because resets should
now already include all required delays (Lukas Wunner)
- Avoid FLR for MediaTek MT7925 WiFi, where FLR fails after a VM
terminates uncleanly (Jose Ignacio Tornos Martinez)
- Avoid SBR for Qualcomm WCN6855/WCN7850 WiFi, SDX62/SDX65 modems,
which seem not to support it correctly (Jose Ignacio Tornos
Martinez)
Peer-to-peer DMA:
- Prevent P2PDMA as well as CPU access to non-mappable BARs, e.g.,
s390 ISM BARs (Matt Evans)
- Add Intel QAT, DSA, IAA devices to whitelist (Lukas Wunner)
Endpoint framework:
- Add endpoint controller APIs for use by function drivers to
discover auxiliary blocks like DMA engines (Koichiro Den)
- Remember DesignWare eDMA engine base/size and expose them via the
EPC aux-resource API (Koichiro Den)
- Add endpoint embedded doorbell fallback, used if MSI allocation
fails (Koichiro Den)
- Validate BAR index and remove dead BAR read in endpoint doorbell
test (Carlos Bilbao)
- Unwind MSI/MSI-X vectors if NTB initialization fails part-way
through (Koichiro Den)
- Cache sleepable pci_irq_vector() value at ISR setup to avoid
calling it from hardirq context (Koichiro Den)
- Call sleepable pci_epc_raise_irq() from a work item instead of
atomic context, e.g., when setting bits in NTB peer doorbells in
the ntb_peer_db_set() path (Koichiro Den)
- Report 0-based vNTB doorbell vector to account for link event 0 and
historically skipped slot 1 (Koichiro Den)
- Prevent configfs writes to vNTB db_count and other values that are
already in use after EPC attach (Koichiro Den)
- Account for vNTB db_valid reserved slots (link event 0 and
historically skipped slot 1) so they don't appear as valid
doorbells (Koichiro Den)
- Implement vNTB .db_vector_count()/mask() for doorbells so clients
can use multiple vectors and avoid thundering herds (Koichiro Den)
- Report 0-based NTB doorbell vector to account for link event 0 and
historically skipped slot 1 (Koichiro Den)
- Fix doorbell bitmask and IRQ vector handling to clear only
specified bits, use the correct vector for non-contiguous Linux IRQ
numbers, and validate incoming vectors (Koichiro Den)
- Implement NTB .db_vector_count()/mask() for doorbells so clients
can use multiple vectors (Koichiro Den)
Native PCIe controller infrastructure:
- Add pci_host_common_link_train_delay() for the mandatory delay
after > 5GT/s Link training completes and use it for cadence HPA,
j721e, LGA; dwc; aardvark, mediatek-gen3, rzg3s (Hans Zhang)
- Protect root bus removal with rescan lock in altera, brcmstb,
cadence, dwc, iproc, mediatek, plda, rockchip to prevent
use-after-free or crashes when racing with sysfs rescan or hotplug
(Hans Zhang)
- Add pci_host_common_parse_ports() for use by any native driver to
parse Root Port properties (per-Link features like width, speed,
PHY, power and reset control, etc should be described in Root Port
stanzas, not the host bridge; currently only reset GPIOs
implemented) (Sherry Sun)
New native PCIe controller drivers:
- Add DT binding and driver for UltraRISC DP1000 PCIe controller
(Xincheng Zhang, Jia Wang)
Altera PCIe controller driver:
- Do not dispose of the parent IRQ mapping, which belongs to the
parent interrupt controller (Mahesh Vaidya)
- Fix chained IRQ handler ordering issue and resource leaks on probe
failure (Mahesh Vaidya)
AMD MDB PCIe controller driver:
- Assert PERST# on shutdown so any connected Endpoints are held in
reset during shutdown (Sai Krishna Musham)
Amlogic Meson PCIe controller driver:
- Propagate devm_add_action_or_reset() failure to fix probe error
path (Shuvam Pandey)
- Add .remove() callback to deinitialize the host bridge and power
off the PHY (Shuvam Pandey)
Broadcom iProc PCIe controller driver:
- Restore .map_irq() assignment; its removal broke INTx on the iproc
platform bus driver (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- No change, but products using certain WiFi devices may be affected
by removal of CONFIG_PCIE_BUS_* (see above)
Freescale i.MX6 PCIe controller driver:
- Move IMX6SX_GPR12_PCIE_TEST_POWERDOWN handling into the core reset
functions (Richard Zhu)
- Assert PERST# before enabling regulators to ensure that even if
power is enabled, endpoint stays inactive until REFCLK is stable
(Sherry Sun)
- Parse reset properties in Root Port nodes (falling back to host
bridge) to help support Key E connectors and the pwrctrl framework
(Sherry Sun)
- Configure i.MX95 REF_USE_PAD before PHY reset (Richard Zhu)
- Assert i.MX95 ref_clk_en after reference clock stabilizes (Richard
Zhu)
- Integrate new pwrctrl API for DTs with Root Port-level power
supplies (Sherry Sun)
Intel Gateway PCIe controller driver:
- Enable clock before PHY init for correct ordering (Florian Eckert)
- Add .start_link() callback so the driver works again (Florian
Eckert)
- Stop overwriting the ATU base address discovered by
dw_pcie_get_resources() (Florian Eckert)
- Add DT 'atu' region since this is hardware-specific, and fall back
to driver default if lacking (Florian Eckert)
Loongson PCIe controller driver:
- Ignore downstream devices only on internal bridges to avoid
Loongson hardware issue (Rong Zhang)
- Quirk old Loongson-3C6000 bridges that advertise incorrect
supported link speeds (Ziyao Li)
Marvell MVEBU PCIe controller driver:
- Use fixed-width interrupt masks to avoid truncation in 64-bit
builds (Rosen Penev)
MediaTek PCIe controller driver:
- Use FIELD_PREP() to fix incorrect operator precedence in
PCIE_FTS_NUM_L0 (Li RongQing)
- Fix IRQ domain leak when port fails to enable (Manivannan
Sadhasivam)
- Use actual physical address for MSI message address instead of
virt_to_phys() (Manivannan Sadhasivam)
- Add EcoNet EN7528 to DT binding (Caleb James DeLisle)
MediaTek PCIe Gen3 controller driver:
- Deassert PCIE_PHY_RSTB so REFCLK is stable for at least 100ms
(PCIE_T_PVPERL_MS) before deasserting PERST# (Jian Yang)
- Add .shutdown() to assert PERST# before powering down device (Jian
Yang)
- Do full device power down on removal, including asserting PERST#,
when removing driver (Chen-Yu Tsai)
- Fix a 'failed to create pwrctrl devices' error message that was
inadvertently skipped (Chen-Yu Tsai)
NVIDIA Tegra194 PCIe controller driver:
- Program the DesignWare PORT_AFR L1 entrance latency based on the
'aspm-l1-entry-delay-ns' DT property (Manikanta Maddireddy)
Qualcomm PCIe controller driver:
- Add Eliza SoC compatible in DT binding (Krishna Chaitanya Chundru)
- Set max OPP during resume so DBI register accesses don't fail with
NoC errors (Qiang Yu)
- Add pci_host_common_d3cold_possible() to determine whether
downstream devices are already in D3hot and wakeup-enabled devices
are capable of generating PME from D3cold (Krishna Chaitanya
Chundru)
- Add .get_ltssm() callback to get the LTSSM status without DBI,
since DBI may be inaccessible after PME_Turn_Off (Krishna Chaitanya
Chundru)
- Power down PHY via PARF_PHY_CTRL before disabling rails/clocks to
avoid power leakage (Krishna Chaitanya Chundru)
- Decide whether suspend should put the link in L2 and power down
using pci_host_common_d3cold_possible() instead of checking whether
ASPM L1 is enabled (Krishna Chaitanya Chundru)
- Add qcom D3cold support to tear down interconnect bandwidth and OPP
votes (Krishna Chaitanya Chundru)
- Handle unsupported mixed PERST#/PHY DT configurations, e.g., PHY in
RP node while PERST# is in the RC node, but warn about the DT issue
(Qiang Yu)
- Program T_POWER_ON based on DT 't-power-on-us' property in case
hardware advertises incorrect values (Krishna Chaitanya Chundru)
- Disable ASPM L0s for SA8775P (Shawn Guo)
- Initialize DWC MSI lock for firmware-managed ECAM hosts, which
don't use the dw_pcie_host_init() path that initializes the lock
(Yadu M G)
Renesas RZ/G3S PCIe controller driver:
- Add RZ/V2N DT support (Lad Prabhakar)
SOPHGO PCIe controller driver:
- Add 'dma-coherent' DT property for sg2042-pcie driver (Han Gao)
Synopsys DesignWare PCIe controller driver:
- Apply ECRC TLP Digest workaround for all DesignWare cores prior to
5.10a, not just 4.90a and 5.00a (Manikanta Maddireddy)
- Use common struct dw_pcie 'mode' rather than duplicating it in
artpec6, dra7xx, dwc-pcie, and keembay driver structs (Hans Zhang)
- Use DEFINE_SHOW_ATTRIBUTE for ltssm_status debugfs to reduce
boilerplate and fix a seq_file memory leak by including a
.release() callback (Hans Zhang)
- Fix a signedness bug in fault injection test code (Dan Carpenter)
- Avoid NULL pointer dereference when tearing down debugfs for
controller that lacks RAS DES capability (Shuvam Pandey)
MicroSemi Switchtec management driver:
- Add Gen6 Device IDs (Ben Reed)
Miscellaneous:
- Remove unused gpio.h include from amd-mdb, designware-plat, fu740,
visconti drivers (Andy Shevchenko)
- Fix typos in documentation (josh ziegler)
- Use FIELD_MODIFY() instead of open-coding it (Hans Zhang)"
* tag 'pci-v7.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (168 commits)
PCI/sysfs: Use kstrtobool() to parse the ROM attribute input
PCI/sysfs: Limit BAR resize attribute scope to platforms with PCI mmap
PCI/sysfs: Remove pci_create_legacy_files() and pci_sysfs_init()
PCI/sysfs: Convert legacy I/O and memory attributes to static definitions
PCI/sysfs: Add __weak pci_legacy_has_sparse() helper
alpha/PCI: Compute legacy size in pci_mmap_legacy_page_range()
PCI: Add macros for legacy I/O and memory address space sizes
PCI/sysfs: Remove pci_{create,remove}_sysfs_dev_files()
alpha/PCI: Convert resource files to static attributes
alpha/PCI: Add static PCI resource attribute macros
alpha/PCI: Remove WARN from __pci_mmap_fits() and __legacy_mmap_fits()
alpha/PCI: Fix __pci_mmap_fits() overflow for zero-length BARs
alpha/PCI: Use PCI resource accessor macros
alpha/PCI: Use BAR index in sysfs attr->private instead of resource pointer
alpha/PCI: Add security_locked_down() check to pci_mmap_resource()
PCI/sysfs: Limit pci_sysfs_init() late_initcall compile scope
PCI/sysfs: Add stubs for pci_{create,remove}_sysfs_dev_files()
PCI/sysfs: Warn about BAR resize failure in __resource_resize_store()
PCI/sysfs: Convert PCI resource files to static attributes
PCI/proc: Fix race between pci_proc_init() and pci_bus_add_device()
...
to the MSI IRQ support code (Yuanhe Shu)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=AQ7U
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2026-06-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq fix from Ingo Molnar:
- Revert a change that added a bad iounmap(NULL) call
to the MSI IRQ support code (Yuanhe Shu)
* tag 'irq-msi-2026-06-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "PCI/MSI: Unmap MSI-X region on error"
- Fix typos in documentation (josh ziegler)
- Use FIELD_MODIFY() instead of open-coding it (Hans Zhang)
* pci/misc:
PCI: Use FIELD_MODIFY() instead of open-coding it
Documentation: PCI: Fix typos
- Remove unused gpio.h include from amd-mdb, designware-plat, fu740,
visconti drivers (Andy Shevchenko)
* pci/controller/misc:
PCI: visconti: Drop unused include
PCI: fu740: Drop unused include
PCI: designware-plat: Drop unused include
PCI: amd-mdb: Use the right GPIO header
- Add common TLP Type macros (MRd/Wr, IORd/Wr, CfgRd/Wr 0, CfgRd/Wr 1, Msg)
and use them in aspeed, cadence, dwc, mediatek, tegra drivers (Hans
Zhang)
* pci/controller/tlp_macros:
PCI: cadence: Use common TLP type macros
PCI: dwc: Replace ATU type macros with common TLP type macros
PCI: Add common TLP type macros and convert aspeed/mediatek
- Protect root bus removal with rescan lock in altera, brcmstb, cadence,
dwc, iproc, mediatek, plda, rockchip to prevent use-after-free or crashes
when racing with sysfs rescan or hotplug (Hans Zhang)
* pci/controller/rescan_lock:
PCI: rockchip: Protect root bus removal with rescan lock
PCI: plda: Protect root bus removal with rescan lock
PCI: mediatek: Protect root bus removal with rescan lock
PCI: iproc: Protect root bus removal with rescan lock
PCI: dwc: Protect root bus removal with rescan lock
PCI: cadence: Protect root bus removal with rescan lock
PCI: brcmstb: Protect root bus removal with rescan lock
PCI: altera: Protect root bus removal with rescan lock
- Add pci_host_common_link_train_delay() for the mandatory delay after
> 5GT/s Link training completes and use it for cadence HPA, j721e, LGA;
dwc; aardvark, mediatek-gen3, rzg3s (Hans Zhang)
* pci/controller/link_train_delay:
PCI: rzg3s-host: Use common pci_host_common_link_train_delay() helper
PCI: mediatek-gen3: Add 100 ms delay after link up
PCI: aardvark: Add 100 ms delay after link training
PCI: dwc: Use common pci_host_common_link_train_delay() helper
PCI: cadence-hpa: Add post-link delay
PCI: cadence: Add post-link delay for LGA and j721e glue driver
PCI: Add pci_host_common_link_train_delay() helper
# Conflicts:
# drivers/pci/controller/pci-host-common.h
- Use fixed-width interrupt masks to avoid truncation in 64-bit builds
(Rosen Penev)
* pci/controller/mvebu:
PCI: mvebu: Use fixed-width interrupt masks to avoid truncation in 64-bit builds
- Deassert PCIE_PHY_RSTB so REFCLK is stable for at least 100ms
(PCIE_T_PVPERL_MS) before deasserting PERST# (Jian Yang)
- Add .shutdown() to assert PERST# before powering down device (Jian Yang)
- Do full device power down on removal, including asserting PERST#, when
removing driver (Chen-Yu Tsai)
- Fix a 'failed to create pwrctrl devices' error message that was
inadvertently skipped (Chen-Yu Tsai)
* pci/controller/mediatek-gen3:
PCI: mediatek-gen3: Fix incorrectly skipped pwrctrl error message
PCI: mediatek-gen3: Do full device power down on removal
PCI: mediatek-gen3: Add a .shutdown() callback to control PERST# signal
PCI: mediatek-gen3: Fix PERST# control timing during system startup
- Use FIELD_PREP() to fix incorrect operator precedence in PCIE_FTS_NUM_L0
(Li RongQing)
- Fix IRQ domain leak when port fails to enable (Manivannan Sadhasivam)
- Use actual physical address for MSI message address instead of
virt_to_phys() (Manivannan Sadhasivam)
- Add EcoNet EN7528 to DT binding (Caleb James DeLisle)
* pci/controller/mediatek:
dt-bindings: PCI: mediatek: Add support for EcoNet EN7528
PCI: mediatek: Use actual physical address instead of virt_to_phys()
PCI: mediatek: Fix IRQ domain leak when port fails to enable
PCI: mediatek: Fix operator precedence in PCIE_FTS_NUM_L0 macro
- Ignore downstream devices only on internal bridges to avoid Loongson
hardware issue (Rong Zhang)
- Quirk old Loongson-3C6000 bridges that advertise incorrect supported link
speeds (Ziyao Li)
* pci/controller/loongson:
PCI: loongson: Override PCIe bridge supported speeds for Loongson-3C6000 series
PCI: loongson: Do not ignore downstream devices on external bridges
- Restore .map_irq() assignment that broke INTx on the iproc platform bus
driver (Mark Tomlinson)
* pci/controller/iproc-bcma:
PCI: iproc: Restore .map_irq() for the platform bus driver
- Program the DesignWare PORT_AFR L1 entrance latency based on the
'aspm-l1-entry-delay-ns' DT property (Manikanta Maddireddy)
* pci/controller/dwc-tegra194:
PCI: tegra194: Use aspm-l1-entry-delay-ns DT property for L1 entrance latency
- Set max OPP during resume so DBI register accesses don't fail with NoC
errors (Qiang Yu)
- Add pci_host_common_d3cold_possible() to determine whether downstream
devices are already in D3hot and wakeup-enabled devices are capable of
generating PME from D3cold (Krishna Chaitanya Chundru)
- Add a .get_ltssm() callback to get the LTSSM status without DBI, since
DBI may be inaccessible after PME_Turn_Off (Krishna Chaitanya Chundru)
- Power down PHY via PARF_PHY_CTRL before disabling rails/clocks to avoid
power leakage (Krishna Chaitanya Chundru)
- Decide whether suspend should put the link in L2 and power down using
pci_host_common_d3cold_possible() instead of checking whether ASPM L1 is
enabled (Krishna Chaitanya Chundru)
- Add qcom D3cold support to tear down interconnect bandwidth and OPP votes
(Krishna Chaitanya Chundru)
- Handle unsupported mixed PERST#/PHY DT configurations, e.g., PHY in RP
node while PERST# is in the RC node, but warn about the DT issue (Qiang
Yu)
- Add pcie_encode_t_power_on() to encode L1SS T_POWER_ON fields (Krishna
Chaitanya Chundru)
- Add dw_pcie_program_t_power_on() to program T_POWER_ON (Krishna Chaitanya
Chundru)
- Program qcom T_POWER_ON based on DT 't-power-on-us' property in case
hardware advertises incorrect values (Krishna Chaitanya Chundru)
- Disable ASPM L0s for SA8775P (Shawn Guo)
- Initialize DWC MSI lock for firmware-managed ECAM hosts, which don't use
the dw_pcie_host_init() path that initializes the lock (Yadu M G)
* pci/controller/dwc-qcom:
PCI: qcom: Initialize DWC MSI lock for firmware-managed ECAM hosts
PCI: qcom: Disable ASPM L0s for SA8775P
PCI: qcom: Program T_POWER_ON
PCI: dwc: Add dw_pcie_program_t_power_on() to program T_POWER_ON
PCI/ASPM: Add pcie_encode_t_power_on() helper to encode L1SS T_POWER_ON fields
PCI: qcom: Handle mixed PERST#/PHY DT configuration
PCI: qcom: Add D3cold support
PCI: dwc: Use common D3cold eligibility helper in suspend path
PCI: qcom: Power down PHY via PARF_PHY_CTRL before disabling rails/clocks
PCI: qcom: Add .get_ltssm() callback to query LTSSM status
PCI: host-common: Add pci_host_common_d3cold_possible() helper
PCI: qcom: Set max OPP before DBI access during resume
# Conflicts:
# drivers/pci/controller/pci-host-common.c
- Enable clock before PHY init for correct ordering (Florian Eckert)
- Add .start_link() callback so the driver works again (Florian Eckert)
- Stop overwriting the ATU base address discovered by
dw_pcie_get_resources() (Florian Eckert)
- Add DT 'atu' region since this is hardware-specific, and fall back to
driver default if lacking (Florian Eckert)
* pci/controller/dwc-intel-gw:
dt-bindings: PCI: intel,lgm-pcie: Add 'atu' resource
PCI: intel-gw: Fix ATU base address setup and add optional DT 'atu' region
PCI: intel-gw: Add .start_link() callback
PCI: intel-gw: Enable clock before PHY init
PCI: intel-gw: Move interrupt enable to own function
PCI: intel-gw: Remove unused PCIE_APP_INTX_OFST definition
- Move IMX6SX_GPR12_PCIE_TEST_POWERDOWN handling into the core reset
functions (Richard Zhu)
- Add pci_host_common_parse_ports() for use by any native driver to parse
Root Port properties (currently only reset GPIOs) (Sherry Sun)
- Assert PERST# before enabling regulators to ensure that even if power is
enabled, endpoint stays inactive until REFCLK is stable (Sherry Sun)
- Parse reset properties in Root Port nodes (falling back to host bridge)
to help support Key E connectors and the pwrctrl framework (Sherry Sun)
- Configure i.MX95 REF_USE_PAD before PHY reset (Richard Zhu)
- Assert i.MX95 ref_clk_en after reference clock stabilizes (Richard Zhu)
- Integrate new pwrctrl API for DTs with Root Port-level power supplies
(Sherry Sun)
* pci/controller/dwc-imx6:
PCI: imx6: Integrate new pwrctrl API
PCI: imx6: Assert ref_clk_en after reference clock stabilizes on i.MX95
PCI: imx6: Configure REF_USE_PAD before PHY reset for i.MX95
PCI: imx6: Parse 'reset-gpios' in Root Port nodes
PCI: imx6: Assert PERST# before enabling regulators
PCI: host-generic: Add common helpers for parsing Root Port properties
dt-bindings: PCI: fsl,imx6q-pcie: Add reset GPIO in Root Port node
PCI: imx6: Fix IMX6SX_GPR12_PCIE_TEST_POWERDOWN handling
- Assert PERST# on shutdown so any connected Endpoints are held in reset
during shutdown (Sai Krishna Musham)
* pci/controller/dwc-amd-mdb:
PCI: amd-mdb: Assert PERST# on shutdown
- Apply ECRC TLP Digest workaround for all DesignWare cores prior to 5.10a,
not just 4.90a and 5.00a (Manikanta Maddireddy)
- Use common struct dw_pcie 'mode' rather than duplicating it in artpec6,
dra7xx, dwc-pcie, and keembay driver structs (Hans Zhang)
- Use DEFINE_SHOW_ATTRIBUTE for ltssm_status debugfs to reduce boilerplate
and fix a seq_file memory leak by including a .release() callback (Hans
Zhang)
- Fix a signedness bug in fault injection test code (Dan Carpenter)
- Avoid NULL pointer dereference when tearing down debugfs for controller
that lacks RAS DES capability (Shuvam Pandey)
* pci/controller/dwc:
PCI: dwc: Avoid dwc_pcie_rasdes_debugfs_deinit() NULL dereference when no RAS DES capability
PCI: dwc: Fix signedness bug in fault injection test code
PCI: dwc: Use DEFINE_SHOW_ATTRIBUTE for ltssm_status debugfs
PCI: keembay: Use common mode field in struct dw_pcie
PCI: dwc: Use common mode field in struct dw_pcie
PCI: artpec6: Use common mode field in struct dw_pcie
PCI: dra7xx: Use common mode field in struct dw_pcie
PCI: dwc: Apply ECRC workaround for DesignWare cores prior to 5.10a
- Do not dispose of the parent IRQ mapping, which belongs to the parent
interrupt controller (Mahesh Vaidya)
- Fix chained IRQ handler ordering issue and resource leaks on probe
failure (Mahesh Vaidya)
* pci/controller/altera:
PCI: altera: Fix resource leaks on probe failure
PCI: altera: Do not dispose parent IRQ mapping
- Request bus reassignment when not probe-only to fix an enumeration
regression on Marvell CN106XX and possibly other DT-based systems
(Ratheesh Kannoth)
* pci/controller/host-common:
PCI: host-common: Request bus reassignment when not probe-only
- Add endpoint controller APIs for use by function drivers to discover
auxiliary blocks like DMA engines (Koichiro Den)
- Remember DesignWare eDMA engine base/size and expose them via the EPC
aux-resource API (Koichiro Den)
- Refactor endpoint doorbell allocation to allow non-MSI doorbells
(Koichiro Den)
- Add endpoint embedded doorbell fallback, used if MSI allocation fails
(Koichiro Den)
- Validate BAR index and remove dead BAR read in endpoint doorbell test
(Carlos Bilbao)
- Unwind MSI/MSI-X vectors if NTB initialization fails part-way through
(Koichiro Den)
- Cache sleepable pci_irq_vector() value at ISR setup to avoid calling it
from hardirq context (Koichiro Den)
- Validate doorbell count when configuring NTB and vNTB doorbells
(Manivannan Sadhasivam)
- Call sleepable pci_epc_raise_irq() from a work item instead of atomic
context, e.g., when setting bits in NTB peer doorbells in the
ntb_peer_db_set() path (Koichiro Den)
- Report 0-based vNTB doorbell vector to account for link event 0 and
historically skipped slot 1 (Koichiro Den)
- Reject unusable vNTB doorbell counts, e.g., if they don't allow space for
link event 0 and historically skipped slot 1 (Koichiro Den)
- Prevent configfs writes to vNTB db_count and other values that are
already in use after EPC attach (Koichiro Den)
- Account for vNTB db_valid reserved slots (link event 0 and historically
skipped slot 1) so they don't appear as valid doorbells (Koichiro Den)
- Implement vNTB .db_vector_count()/mask() for doorbells so clients can use
multiple vectors and avoid thundering herds (Koichiro Den)
- Report 0-based NTB doorbell vector to account for link event 0 and
historically skipped slot 1 (Koichiro Den)
- Fix doorbell bitmask and IRQ vector handling to clear only specified
bits, use the correct vector for non-contiguous Linux IRQ numbers, and
validate incoming vectors (Koichiro Den)
- Implement NTB .db_vector_count()/mask() for doorbells so clients can use
multiple vectors (Koichiro Den)
* pci/endpoint:
NTB: epf: Implement .db_vector_count()/mask() for doorbells
NTB: epf: Fix doorbell bitmask and IRQ vector handling
NTB: epf: Report 0-based doorbell vector via ntb_db_event()
NTB: epf: Make db_valid_mask cover only real doorbell bits
NTB: epf: Document legacy doorbell slot offset in ntb_epf_peer_db_set()
PCI: endpoint: pci-epf-vntb: Implement .db_vector_count()/mask() for doorbells
PCI: endpoint: pci-epf-vntb: Exclude reserved slots from db_valid_mask
PCI: endpoint: pci-epf-vntb: Guard configfs writes after EPC attach
PCI: endpoint: pci-epf-vntb: Reject unusable doorbell counts
PCI: endpoint: pci-epf-vntb: Report 0-based doorbell vector via ntb_db_event()
PCI: endpoint: pci-epf-vntb: Defer pci_epc_raise_irq() out of atomic context
PCI: endpoint: pci-epf-vntb: Document legacy MSI doorbell offset
PCI: endpoint: pci-epf-ntb: Add check to detect 'db_count' value of 0
PCI: endpoint: pci-epf-vntb: Add check to detect 'db_count' value of 0
NTB: epf: Avoid calling pci_irq_vector() from hardirq context
NTB: epf: Fix request_irq() unwind in ntb_epf_init_isr()
misc: pci_endpoint_test: Remove dead BAR read before doorbell trigger
misc: pci_endpoint_test: Validate BAR index in doorbell test
PCI: endpoint: pci-ep-msi: Add embedded doorbell fallback
PCI: endpoint: pci-epf-test: Reuse pre-exposed doorbell targets
PCI: endpoint: pci-epf-vntb: Reuse pre-exposed doorbells and IRQ flags
PCI: endpoint: pci-ep-msi: Refactor doorbell allocation for new backends
PCI: dwc: ep: Expose integrated eDMA resources via EPC aux-resource API
PCI: dwc: Record integrated eDMA register window
PCI: endpoint: Add auxiliary resource query API
- Avoid FLR for MediaTek MT7925 WiFi, where FLR fails after a VM terminates
uncleanly (Jose Ignacio Tornos Martinez)
- Avoid SBR for Qualcomm WCN6855/WCN7850 WiFi, SDX62/SDX65 modems, which
seem not to support it correctly (Jose Ignacio Tornos Martinez)
* pci/virtualization:
PCI: Avoid SBR for Qualcomm WCN6855/WCN7850 WiFi, SDX62/SDX65 modems
PCI: Avoid FLR for MediaTek MT7925 WiFi
- Require CAP_SYS_ADMIN to write to sysfs 'resourceN_resize' attributes
(Krzysztof Wilczyński)
- Convert PCI resource files to static attributes to avoid races that cause
'duplicate filename' warnings and boot panics (Krzysztof Wilczyński)
- Remove pci_create_sysfs_dev_files() and pci_remove_sysfs_dev_files(),
which are obsolete after converting to static attributes (Krzysztof
Wilczyński)
- Add security_locked_down(LOCKDOWN_PCI_ACCESS) to alpha PCI resource mmap
path to match the generic path (Krzysztof Wilczyński)
- Convert sysfs 'legacy_io' and 'legacy_mem' to static attributes
(Krzysztof Wilczyński)
- Remove pci_create_legacy_files() and pci_sysfs_init(), which are obsolete
after converting to static attributes (Krzysztof Wilczyński)
- Expose sysfs 'resourceN_resize' attributes only on platforms with PCI
mmap (Krzysztof Wilczyński)
- Use kstrtobool() to parse the 'rom' attribute input to avoid the
unexpected behavior of enabling the ROM when writing '0' with no trailing
newline (Krzysztof Wilczyński)
* pci/sysfs:
PCI/sysfs: Use kstrtobool() to parse the ROM attribute input
PCI/sysfs: Limit BAR resize attribute scope to platforms with PCI mmap
PCI/sysfs: Remove pci_create_legacy_files() and pci_sysfs_init()
PCI/sysfs: Convert legacy I/O and memory attributes to static definitions
PCI/sysfs: Add __weak pci_legacy_has_sparse() helper
alpha/PCI: Compute legacy size in pci_mmap_legacy_page_range()
PCI: Add macros for legacy I/O and memory address space sizes
PCI/sysfs: Remove pci_{create,remove}_sysfs_dev_files()
alpha/PCI: Convert resource files to static attributes
alpha/PCI: Add static PCI resource attribute macros
alpha/PCI: Remove WARN from __pci_mmap_fits() and __legacy_mmap_fits()
alpha/PCI: Fix __pci_mmap_fits() overflow for zero-length BARs
alpha/PCI: Use PCI resource accessor macros
alpha/PCI: Use BAR index in sysfs attr->private instead of resource pointer
alpha/PCI: Add security_locked_down() check to pci_mmap_resource()
PCI/sysfs: Limit pci_sysfs_init() late_initcall compile scope
PCI/sysfs: Add stubs for pci_{create,remove}_sysfs_dev_files()
PCI/sysfs: Warn about BAR resize failure in __resource_resize_store()
PCI/sysfs: Convert PCI resource files to static attributes
PCI/sysfs: Add static PCI resource attribute macros
PCI/sysfs: Add CAP_SYS_ADMIN check to __resource_resize_store()
PCI/sysfs: Split pci_llseek_resource() for device and legacy attributes
PCI/sysfs: Only allow supported resource types in I/O and MMIO helpers
PCI: Add pci_resource_is_io() and pci_resource_is_mem() helpers
PCI/sysfs: Use PCI resource accessor macros
- Check option ROM header signatures and lengths before accessing to avoid
page faults and alignment faults (Guixin Liu)
* pci/rom:
PCI: Check ROM header and data structure addr before accessing
PCI: Introduce named defines for PCI ROM
- Log device readiness timeouts as errors, not warnings (Bjorn Helgaas)
- Wait for device readiness after soft reset (D3hot -> D0uninitialized
transition), when the device may respond with Request Retry Status if it
needs more time to initialize (Bjorn Helgaas)
- Drop unnecessary retries when restoring BARs (Lukas Wunner)
* pci/reset:
PCI: Drop unnecessary retries when restoring BARs
PCI: Wait for device readiness after D3hot -> D0uninitialized transition
PCI: Log device readiness timeouts as errors
- Don't try to power on/off devices unless we know they actually support
power control (Manivannan Sadhasivam)
* pci/pwrctrl:
PCI/pwrctrl: Lock device when calling device_is_bound()
PCI/pwrctrl: Do not try to power on/off devices that don't need pwrctrl
PCI/pwrctrl: Move pci_pwrctrl_is_required() earlier in file
- Fix race between pci_proc_init() and pci_bus_add_device() (Krzysztof
Wilczyński)
* pci/procfs:
PCI/proc: Fix race between pci_proc_init() and pci_bus_add_device()
- Set power state to 'unknown' for all devices, not just those with
drivers, during suspend (Lukas Wunner)
- Skip restoring Resizable BARs and VF Resizable BARs if device doesn't
respond to config reads, to avoid invalid array accesses (Marco
Nenciarini)
- Add pci_suspend_retains_context() so drivers can tell whether devices may
be reset while resuming from suspend due to platform issues; use this in
nvme to avoid issues on Qcom RCs (Manivannan Sadhasivam)
* pci/pm:
nvme-pci: Use pci_suspend_retains_context() during suspend
PCI: qcom: Indicate broken L1SS exit during resume from system suspend
PCI: Indicate context lost if L1SS exit is broken during resume from system suspend
PCI: Add pci_suspend_retains_context() to check if device state is preserved during suspend
PCI/IOV: Skip VF Resizable BAR restore on read error
PCI: Skip Resizable BAR restore on read error
PCI: Stop setting cached power state to 'unknown' on unbind
- Prevent P2PDMA as well as CPU access to non-mappable BARs, e.g., s390 ISM
BARs (Matt Evans)
- Add Intel QAT, DSA, IAA devices to whitelist (Lukas Wunner)
* pci/p2pdma:
PCI/P2PDMA: Add Intel QAT, DSA, IAA devices to whitelist
PCI/P2PDMA: Avoid returning a provider for non_mappable_bars
- Remove MPS/MRRS Kconfig settings (CONFIG_PCIE_BUS_*) that worked around a
WiFi device defect (Bjorn Helgaas)
- Always lift 2.5GT/s restriction in PCIe failed link retraining to avoid
clamping a link to 2.5GT/s after hot-plug changes the device (Maciej W.
Rozycki)
- Don't bother trying to retrain a 2.5GT/s link at 2.5GT/s since nothing
would be gained by the retrain (Maciej W. Rozycki)
* pci/enumeration:
PCI: Bail out early for 2.5GT/s devices in PCIe failed link retraining
PCI: Use pcie_get_speed_cap() in PCIe failed link retraining
PCI: Always lift 2.5GT/s restriction in PCIe failed link retraining
PCI: Remove MPS/MRRS Kconfig settings (CONFIG_PCIE_BUS_*)
