Add microchip,mcp9601 compatible in addition to the original
microchip,mcp9600 to designate support between these two chips.
The current dt-binding has open-circuit and short-circuit as interrupt
names, but these are only supported in mcp9601.
The OC and SC detection requires that mcp9601 VSENSE be wired up, which
not only enables the OC SC interrupts, but also the OC and SC status
register bits.
Add a microchip,vsense boolean to show the chip is wired for this
support.
Add constraints so this feature only applies if the mcp9601 compatible
is selected.
Signed-off-by: Ben Collins <bcollins@watter.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250822-upstream-changes-v8-2-40bb1739e3e2@watter.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Document the clock property in sc7280 LPASS LPI pinctrl node.
Clock settings required for Audioreach solution.
The existing SC7280 platform only supports non-ADSP audio solutions.
To enable audio functionality on ADSP with the AudioReach solution.
additional core and audio hardware clocks must be configured.
Without these clocks, the ADSP will crash.
Signed-off-by: Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com>
Co-developed-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/20250821044914.710044-3-quic_pkumpatl@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
apic_pending_intr_clear() is fundamentally voodoo programming. It's primary
purpose is to clear stale ISR bits in the local APIC, which would otherwise
lock the corresponding interrupt priority level.
The comments and the implementation claim falsely that after clearing the
stale ISR bits, eventually stale IRR bits would be turned into ISR bits and
can be cleared as well. That's just wishful thinking because:
1) If interrupts are disabled, the APIC does not propagate an IRR bit to
the ISR.
2) If interrupts are enabled, then the APIC propagates the IRR bit to the
ISR and raises the interrupt in the CPU, which means that code _cannot_
observe the ISR bit for any of those IRR bits.
Rename the function to reflect the purpose and make exactly _one_ attempt
to EOI the pending ISR bits and add comments why traversing the pending bit
map in low to high priority order is correct.
Instead of trying to "clear" IRR bits, simply print a warning message when
the IRR is not empty.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/871ppwih4s.ffs@tglx
Introduce virt/ directory to collect virtchnl files.
We are going to implement a few sizable extensions soon, each of them
increasing virt/ size, so it looks sensible to introduce a new dir.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
As is already documented in this file, Type-K is the default, so make
that explicit in the dt-bindings.
Signed-off-by: Ben Collins <bcollins@watter.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250822-upstream-changes-v8-1-40bb1739e3e2@watter.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dev_err_probe() doesn't do anything when the error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just return the
value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Acked-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250821080723.525379-8-zhao.xichao@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dev_err_probe() doesn't do anything when the error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just return the
value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250821080723.525379-7-zhao.xichao@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dev_err_probe() doesn't do anything when the error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just return the
value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250821080723.525379-6-zhao.xichao@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dev_err_probe() doesn't do anything when the error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just return the
value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250821080723.525379-5-zhao.xichao@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dev_err_probe() doesn't do anything when the error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just return the
value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Gustavo Silva <gustavograzs@gmail.com> # for ens160
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250821080723.525379-4-zhao.xichao@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dev_err_probe() doesn't do anything when the error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just return the
value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # meson_saradc
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250821080723.525379-3-zhao.xichao@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dev_err_probe() doesn't do anything when the error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just return the
value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/20250821080723.525379-2-zhao.xichao@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Anand left AMD/Xilinx some time ago. Salih and Connall are new
maintainers of xilinx-ams driver.
Signed-off-by: Salih Erim <salih.erim@amd.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Acked-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Link: https://patch.msgid.link/20250820100519.2272509-1-salih.erim@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove the call to `dev_set_drvdata()` and the associated comment
since private data is never read.
Signed-off-by: Salah Triki <salah.triki@gmail.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/aKSRpTuwA0P-ZaUS@pc
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 65e8202f03 ("iio: Remove error prints for
devm_add_action_or_reset()") accidentally introduced a bug where we
returned "ret" but the error code was stored in "error" if
devm_add_action_or_reset() failed. Using two variables to store error
codes is unnecessary and confusing. Delete the "error" variable and use
"ret" everywhere instead.
Fixes: 65e8202f03 ("iio: Remove error prints for devm_add_action_or_reset()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://patch.msgid.link/aKSSHTdJf5QoYiRx@stanley.mountain
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Avoid triggering a dereference of an error pointer on cleanup in
xe_vm_free_scratch() by clearing any scratch_pt error pointer.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Fixes: 06951c2ee7 ("drm/xe: Use NULL PTEs as scratch PTEs")
Cc: Brian Welty <brian.welty@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v6.8+
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250821143045.106005-4-thomas.hellstrom@linux.intel.com
This member is set when exporting using prime. However
the xe_gem_prime_export() alone doesn't set it, since it's done
later in the prime export flow.
For the test, set it manually and remove the hack that set it
temporarily when it was really needed.
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250821143045.106005-3-thomas.hellstrom@linux.intel.com
The pinning has the odd side-effect that unlocking *any* resv
during validation triggers an "unlocking pinned lock" warning.
Cc: Matthew Brost <matthew.brost@intel.com>
Fixes: 9d5558649f ("drm/xe: Rework eviction rejection of bound external bos")
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250821143045.106005-2-thomas.hellstrom@linux.intel.com
Currently we are ignoriong drm_dp_dpcd_read return values when reading PSR
and Panel Replay capability DPCD register. Rework intel_psr_dpcd a bit to
take care of checking the return value.
v2: use drm_dp_dpcd_read_data
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250821045918.17757-1-jouni.hogander@intel.com
Marking ufence as signalled after copy_to_user() is too late.
Worker thread which signals ufence by memory write might be raced
with another userspace vm-bind call. In map/unmap scenario unmap
may still see ufence is not signalled causing -EBUSY. Change the
order of marking / write to user-fence fixes this issue.
Fixes: 977e5b82e0 ("drm/xe: Expose user fence from xe_sync_entry")
Link: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/5536
Signed-off-by: Zbigniew Kempczyński <zbigniew.kempczynski@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Link: https://lore.kernel.org/r/20250820083903.2109891-2-zbigniew.kempczynski@intel.com
The userspace load can put up to 2048 bits into an xlen bit stack
buffer. We want only xlen bits, so check the size beforehand.
Fixes: 2fa290372d ("RISC-V: KVM: add 'vlenb' Vector CSR")
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@ventanamicro.com>
Reviewed-by: Nutty Liu <liujingqi@lanxincomputing.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Link: https://lore.kernel.org/r/20250805104418.196023-4-rkrcmar@ventanamicro.com
Signed-off-by: Anup Patel <anup@brainfault.org>
Currently, kvm_riscv_gstage_ioremap() is used to map IMSIC gpa to the
spa of IMSIC guest interrupt file.
The PAGE_KERNEL_IO property includes global setting whereas it does not
include user mode settings, so when accessing the IMSIC address in the
virtual machine, a guest page fault will occur, this is not expected.
According to the RISC-V Privileged Architecture Spec, for G-stage address
translation, all memory accesses are considered to be user-level accesses
as though executed in U-mode.
Fixes: 659ad6d82c ("RISC-V: KVM: Use PAGE_KERNEL_IO in kvm_riscv_gstage_ioremap()")
Signed-off-by: Fangyu Yu <fangyu.yu@linux.alibaba.com>
Reviewed-by: Radim Krčmář <rkrcmar@ventanamicro.com>
Reviewed-by: Nutty Liu <nutty.liu@hotmail.com>
Link: https://lore.kernel.org/r/20250807070729.89701-1-fangyu.yu@linux.alibaba.com
Signed-off-by: Anup Patel <anup@brainfault.org>
We need override certain link rates in favour of the next available
higher link rate. The Link rates that need to be overridden are
indicated by a mask in VBT. To make sure these modes are skipped we
don't add them in them in the sink rates array.
--v2
-Update the link rates after we have a final set of link rates [Ankit]
-Break this patch up [Ankit]
-Optimize the assingment during loop [Ankit]
--v3
-Add protection against broken VBTs [Jani]
--v4
-Fix build errors
-Create a seprate function to check if edp data override is selected
and using the correct vbt
--v5
-Use correct number to check the num of edp rates [Ankit]
--v6
-No seprate function check if vbt is broken in the reject rate function
[Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250821042653.269227-4-suraj.kandpal@intel.com
Add a function that helps identify if the rate provided needs to
be overridden. For this we need a function that compares the rate
provided and bitmask of rates provided in VBT.
--v2
-Rename functions [Jani]
-Return the mask instead of parsing it in function [Jani]
-Move the declaration in header [Jani]
--v3
-Change function name to depict what the function does [Ankit]
--v4
-Lets not use hweight [Ankit]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250821042653.269227-3-suraj.kandpal@intel.com
Add edp_data_rate_override field VBT which gives us a mask
of rates which needs to be skipped in favour of
subsequent higher rate.
--v2
-Rename vbt field [Jani]
-Fix comment to 263+ [Jani]
-Use BIT_U32 [Jani]
-Fix the bits assignment in vbt [Jani]
--v3
-Add a mask which represents all link rates [Ankit]
Bspec: 20124
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://lore.kernel.org/r/20250821042653.269227-2-suraj.kandpal@intel.com
The dev_err_probe() doesn't do anything when error is '-ENOMEM'.
Therefore, remove the useless call to dev_err_probe(), and just
return the value instead.
Signed-off-by: Xichao Zhao <zhao.xichao@vivo.com>
Reviewed-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Message-ID: <20250819112654.588527-1-zhao.xichao@vivo.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a defer probe happens for the cpu device, the return value for
cpu_pdev "ret = -EINVAL" breaks defer probe. As the cpus->dai_name
can be replaced by cpus->of_node, to simplify the code, remove related
code for cpu_pdev.
Fixes: 6a5f850aa8 ("ASoC: fsl: Add imx-hdmi machine driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Message-ID: <20250820031641.2158261-1-shengjiu.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the current design, the `pm8008_regulator_get_voltage_sel()` callback
can return a negative value if the raw voltage value is read as 0 uV from
the PMIC HW register. This can cause the probe to fail when the
`machine_constraints_voltage()` check is called during the regulator
registration flow.
Fix this by using the helper `regulator_map_voltage_linear_range()` to
convert the raw value to a voltage selector inside the mentioned get
voltage selector function. This ensures that the value returned is always
within the defined range.
Signed-off-by: Kamal Wadhwa <kamal.wadhwa@oss.qualcomm.com>
Message-ID: <20250823-pm8008-negitive-selector-v1-1-52b026a4b5e8@quicinc.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_soc_lookup_component_nolocked() is very complex today.
Let's tidyup the code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Message-ID: <87cy8sysuy.wl-kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
soc-generic-dmaengine-pcm.c uses same dev for both CPU and Platform.
In such case, CPU component driver might not have driver->name, then
snd_soc_lookup_component_nolocked() will be NULL pointer access error.
Care NULL driver name.
Call trace:
strcmp from snd_soc_lookup_component_nolocked+0x64/0xa4
snd_soc_lookup_component_nolocked from snd_soc_unregister_component_by_driver+0x2c/0x44
snd_soc_unregister_component_by_driver from snd_dmaengine_pcm_unregister+0x28/0x64
snd_dmaengine_pcm_unregister from devres_release_all+0x98/0xfc
devres_release_all from device_unbind_cleanup+0xc/0x60
device_unbind_cleanup from really_probe+0x220/0x2c8
really_probe from __driver_probe_device+0x88/0x1a0
__driver_probe_device from driver_probe_device+0x30/0x110
driver_probe_device from __driver_attach+0x90/0x178
__driver_attach from bus_for_each_dev+0x7c/0xcc
bus_for_each_dev from bus_add_driver+0xcc/0x1ec
bus_add_driver from driver_register+0x80/0x11c
driver_register from do_one_initcall+0x58/0x23c
do_one_initcall from kernel_init_freeable+0x198/0x1f4
kernel_init_freeable from kernel_init+0x1c/0x12c
kernel_init from ret_from_fork+0x14/0x28
Fixes: 144d6dfc74 ("ASoC: soc-core: merge snd_soc_unregister_component() and snd_soc_unregister_component_by_driver()")
Reported-by: J. Neuschäfer <j.ne@posteo.net>
Closes: https://lore.kernel.org/r/aJb311bMDc9x-dpW@probook
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reported-by: Ondřej Jirman <megi@xff.cz>
Closes: https://lore.kernel.org/r/arxpwzu6nzgjxvsndct65ww2wz4aezb5gjdzlgr24gfx7xvyih@natjg6dg2pj6
Tested-by: J. Neuschäfer <j.ne@posteo.net>
Message-ID: <87ect8ysv8.wl-kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for IORING_CQE_F_32 as well, not just if the ring was setup with
IORING_SETUP_CQE32 to only support big CQEs.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Ensure that the CQ ring iteration handles differently sized CQEs, not
just a fixed 16b or 32b size per ring. These CQEs aren't possible just
yet, but prepare the fdinfo CQ ring dumping for handling them.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This adds the CQE flags related to supporting a mixed CQ ring mode, where
both normal (16b) and big (32b) CQEs may be posted.
No functional changes in this patch.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_uring_cmd_prep() checks that REQ_F_BUFFER_SELECT is set in the
io_kiocb's flags iff IORING_URING_CMD_MULTISHOT is set in the SQE's
uring_cmd_flags. Consolidate the IORING_URING_CMD_MULTISHOT and
!IORING_URING_CMD_MULTISHOT branches into a single check that the
IORING_URING_CMD_MULTISHOT flag matches the REQ_F_BUFFER_SELECT flag.
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250821163308.977915-4-csander@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
io_uring_cmd_prep() currently has two checks for whether
IORING_URING_CMD_FIXED and IORING_URING_CMD_MULTISHOT are both set in
uring_cmd_flags. Remove the second check.
Signed-off-by: Caleb Sander Mateos <csander@purestorage.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250821163308.977915-3-csander@purestorage.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add UAPI flag IORING_URING_CMD_MULTISHOT for supporting multishot
uring_cmd operations with provided buffer.
This enables drivers to post multiple completion events from a single
uring_cmd submission, which is useful for:
- Notifying userspace of device events (e.g., interrupt handling)
- Supporting devices with multiple event sources (e.g., multi-queue devices)
- Avoiding the need for device poll() support when events originate
from multiple sources device-wide
The implementation adds two new APIs:
- io_uring_cmd_select_buffer(): selects a buffer from the provided
buffer group for multishot uring_cmd
- io_uring_mshot_cmd_post_cqe(): posts a CQE after event data is
pushed to the provided buffer
Multishot uring_cmd must be used with buffer select (IOSQE_BUFFER_SELECT)
and is mutually exclusive with IORING_URING_CMD_FIXED for now.
The ublk driver will be the first user of this functionality:
https://github.com/ming1/linux/commits/ublk-devel/
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250821040210.1152145-3-ming.lei@redhat.com
[axboe: fold in fix for !CONFIG_IO_URING]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently the buffer list is stored in struct io_kiocb. The buffer list
can be of two types:
1) Classic/legacy buffer list. These don't need to get referenced after
a buffer pick, and hence storing them in struct io_kiocb is perfectly
fine.
2) Ring provided buffer lists. These DO need to be referenced after the
initial buffer pick, as they need to get consumed later on. This can
be either just incrementing the head of the ring, or it can be
consuming parts of a buffer if incremental buffer consumptions has
been configured.
For case 2, io_uring needs to be careful not to access the buffer list
after the initial pick-and-execute context. The core does recycling of
these, but it's easy to make a mistake, because it's stored in the
io_kiocb which does persist across multiple execution contexts. Either
because it's a multishot request, or simply because it needed some kind
of async trigger (eg poll) for retry purposes.
Add a struct io_buffer_list to struct io_br_sel, which is always on
stack for the various users of it. This prevents the buffer list from
leaking outside of that execution context, and additionally it enables
kbuf to not even pass back the struct io_buffer_list if the given
context isn't appropriately locked already.
This doesn't fix any bugs, it's simply a defensive measure to prevent
any issues with reuse of a buffer list.
Link: https://lore.kernel.org/r/20250821020750.598432-12-axboe@kernel.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently a pointer is passed in to the 'ret' in the send mshot handler,
but since we already have a value field in io_br_sel, just use that.
This is also in preparation for needing to pass in struct io_br_sel
to io_send_finish() anyway.
Link: https://lore.kernel.org/r/20250821020750.598432-11-axboe@kernel.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently a pointer is passed in to the 'ret' in the receive handlers,
but since we already have a value field in io_br_sel, just use that.
This is also in preparation for needing to pass in struct io_br_sel
to io_recv_finish() anyway.
Link: https://lore.kernel.org/r/20250821020750.598432-10-axboe@kernel.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
