The current single-bit error injection mechanism flips bits directly in ECC RAM
by performing write and read operations. When the ECC RAM is actively used by
the Ethernet or USB controller, this approach sometimes trigger a false
double-bit error.
Switch both Ethernet and USB EDAC devices to use the INTTEST register
(altr_edac_a10_device_inject_fops) for single-bit error injection, similar to
the existing double-bit error injection method.
Fixes: 064acbd4f4 ("EDAC, altera: Add Stratix10 peripheral support")
Signed-off-by: Niravkumar L Rabara <niravkumarlaxmidas.rabara@altera.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251111081333.1279635-1-niravkumarlaxmidas.rabara@altera.com
This handles PA Sync Lost event which previously was assumed to be
handled with BIG Sync Lost but their lifetime are not the same thus why
there are 2 different events to inform when each sync is lost.
Fixes: b2a5f2e1c1 ("Bluetooth: hci_event: Add support for handling LE BIG Sync Lost event")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The OCRAM ECC is always enabled either by the BootROM or by the Secure Device
Manager (SDM) during a power-on reset on SoCFPGA.
However, during a warm reset, the OCRAM content is retained to preserve data,
while the control and status registers are reset to their default values. As
a result, ECC must be explicitly re-enabled after a warm reset.
Fixes: 17e47dc6db ("EDAC/altera: Add Stratix10 OCRAM ECC support")
Signed-off-by: Niravkumar L Rabara <niravkumarlaxmidas.rabara@altera.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20251111080801.1279401-1-niravkumarlaxmidas.rabara@altera.com
Quang Le reported that the AF_UNIX GC could garbage-collect a
receive queue of an alive in-flight socket, with a nice repro.
The repro consists of three stages.
1)
1-a. Create a single cyclic reference with many sockets
1-b. close() all sockets
1-c. Trigger GC
2)
2-a. Pass sk-A to an embryo sk-B
2-b. Pass sk-X to sk-X
2-c. Trigger GC
3)
3-a. accept() the embryo sk-B
3-b. Pass sk-B to sk-C
3-c. close() the in-flight sk-A
3-d. Trigger GC
As of 2-c, sk-A and sk-X are linked to unix_unvisited_vertices,
and unix_walk_scc() groups them into two different SCCs:
unix_sk(sk-A)->vertex->scc_index = 2 (UNIX_VERTEX_INDEX_START)
unix_sk(sk-X)->vertex->scc_index = 3
Once GC completes, unix_graph_grouped is set to true.
Also, unix_graph_maybe_cyclic is set to true due to sk-X's
cyclic self-reference, which makes close() trigger GC.
At 3-b, unix_add_edge() allocates unix_sk(sk-B)->vertex and
links it to unix_unvisited_vertices.
unix_update_graph() is called at 3-a. and 3-b., but neither
unix_graph_grouped nor unix_graph_maybe_cyclic is changed
because both sk-B's listener and sk-C are not in-flight.
3-c decrements sk-A's file refcnt to 1.
Since unix_graph_grouped is true at 3-d, unix_walk_scc_fast()
is finally called and iterates 3 sockets sk-A, sk-B, and sk-X:
sk-A -> sk-B (-> sk-C)
sk-X -> sk-X
This is totally fine. All of them are not yet close()d and
should be grouped into different SCCs.
However, unix_vertex_dead() misjudges that sk-A and sk-B are
in the same SCC and sk-A is dead.
unix_sk(sk-A)->scc_index == unix_sk(sk-B)->scc_index <-- Wrong!
&&
sk-A's file refcnt == unix_sk(sk-A)->vertex->out_degree
^-- 1 in-flight count for sk-B
-> sk-A is dead !?
The problem is that unix_add_edge() does not initialise scc_index.
Stage 1) is used for heap spraying, making a newly allocated
vertex have vertex->scc_index == 2 (UNIX_VERTEX_INDEX_START)
set by unix_walk_scc() at 1-c.
Let's track the max SCC index from the previous unix_walk_scc()
call and assign the max + 1 to a new vertex's scc_index.
This way, we can continue to avoid Tarjan's algorithm while
preventing misjudgments.
Fixes: ad081928a8 ("af_unix: Avoid Tarjan's algorithm if unnecessary.")
Reported-by: Quang Le <quanglex97@gmail.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20251109025233.3659187-1-kuniyu@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Owing to the ID registers being global to the VM, there is no point
in computing them more than once. However, recent changes making
use of kvm_set_vm_id_reg() outlined that we repeatedly hammer
the ID registers when we shouldn't.
Gate the ID reg update on the VM having never run.
Fixes: 50e7cce81b ("KVM: arm64: Limit clearing of ID_{AA64PFR0,PFR1}_EL1.GIC to userspace irqchip")
Fixes: 5cb57a1aff ("KVM: arm64: Zero ID_AA64PFR0_EL1.GIC when no GICv3 is presented to the guest")
Closes: https://lore.kernel.org/r/aRHf6x5umkTYhYJ3@finisterre.sirena.org.uk
Reported-by: Mark Brown <broonie@kernel.org>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://patch.msgid.link/20251110173010.1918424-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
In fact, it is a multi-threaded MIPS34Kc, not a single-threaded MIPS24Kc.
Fixes: 0ec4887009 ("mips: dts: Add EcoNet DTS with EN751221 and SmartFiber XP8421-B board")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Fix a regression that has caused accesses to the PCI MMIO window to
complete unclaimed in non-EVA configurations with the SOC-it family of
system controllers, preventing PCI devices from working that use MMIO.
In the non-EVA case PHYS_OFFSET is set to 0, meaning that PCI_BAR0 is
set with an empty mask (and PCI_HEAD4 matches addresses starting from 0
accordingly). Consequently all addresses are matched for incoming DMA
accesses from PCI. This seems to confuse the system controller's logic
and outgoing bus cycles targeting the PCI MMIO window seem not to make
it to the intended devices.
This happens as well when a wider mask is used with PCI_BAR0, such as
0x80000000 or 0xe0000000, that makes addresses match that overlap with
the PCI MMIO window, which starts at 0x10000000 in our configuration.
Set the mask in PCI_BAR0 to 0xf0000000 for non-EVA then, covering the
non-EVA maximum 256 MiB of RAM, which is what YAMON does and which used
to work correctly up to the offending commit. Set PCI_P2SCMSKL to match
PCI_BAR0 as required by the system controller's specification, and match
PCI_P2SCMAPL to PCI_HEAD4 for identity mapping.
Verified with:
Core board type/revision = 0x0d (Core74K) / 0x01
System controller/revision = MIPS SOC-it 101 OCP / 1.3 SDR-FW-4:1
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x1c
Processor ID/revision = 0x97 (MIPS 74Kf) / 0x4c
for non-EVA and with:
Core board type/revision = 0x0c (CoreFPGA-5) / 0x00
System controller/revision = MIPS ROC-it2 / 0.0 FW-1:1 (CLK_unknown) GIC
Processor Company ID/options = 0x01 (MIPS Technologies, Inc.) / 0x00
Processor ID/revision = 0xa0 (MIPS interAptiv UP) / 0x20
for EVA/non-EVA, fixing:
defxx 0000:00:12.0: assign IRQ: got 10
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
0000:00:12.0: Could not read adapter factory MAC address!
vs:
defxx 0000:00:12.0: assign IRQ: got 10
defxx: v1.12 2021/03/10 Lawrence V. Stefani and others
0000:00:12.0: DEFPA at MMIO addr = 0x10142000, IRQ = 10, Hardware addr = 00-00-f8-xx-xx-xx
0000:00:12.0: registered as fddi0
for non-EVA and causing no change for EVA.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 422dd25664 ("MIPS: Malta: Allow PCI devices DMA to lower 2GB physical")
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Some Marvell AP firmware used with mwl8k misbehaves when beacon frames
do not contain a WLAN_EID_DS_PARAMS element with the current channel.
It was reported on OpenWrt Github issues [0].
When hostapd/mac80211 omits DSSS Parameter Set from the beacon (which is
valid on some bands), the firmware stops transmitting sane frames and RX
status starts reporting bogus channel information. This makes AP mode
unusable.
Newer Marvell drivers (mwlwifi [1]) hard-code DSSS Parameter Set into
AP beacons for all chips, which suggests this is a firmware requirement
rather than a mwl8k-specific quirk.
Mirror that behaviour in mwl8k: when setting the beacon, check if
WLAN_EID_DS_PARAMS is present, and if not, extend the beacon and inject
a DSSS Parameter Set element, using the current channel from
hw->conf.chandef.chan.
Tested on Linksys EA4500 (88W8366).
[0] https://github.com/openwrt/openwrt/issues/19088
[1] db97edf20f/hif/fwcmd.c (L675)
Fixes: b64fe619e3 ("mwl8k: basic AP interface support")
Tested-by: Antony Kolitsos <zeusomighty@hotmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://patch.msgid.link/20251111100733.2825970-3-paweldembicki@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The i.MX6UL reference manual lists two possible interrupt lines for
SAI3 (56 and 57, offset +32). The current device tree entry uses
the first one (24), which prevents IRQs from being handled properly.
Use the second interrupt line (25), which does allow interrupts
to work as expected.
Fixes: 36e2edf6ac ("ARM: dts: imx6ul: add sai support")
Signed-off-by: Maarten Zanders <maarten@zanders.be>
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If for example the sniffer did not follow any AIDs in an MU frame, then
some of the information may not be filled in or is even expected to be
invalid. As an example, in that case it is expected that Nss is zero.
Fixes: 2ff5e52e78 ("radiotap: add 0-length PSDU "not captured" type")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20251110142554.83a2858ee15b.I9f78ce7984872f474722f9278691ae16378f0a3e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix an ath11k transmit status reporting issue. This issue has always
been present, but not reported until recently.
Bringing this through the current release since there is now a
userspace entity that wants to leverage this.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCaRH9agAKCRAsFbugiYzL
e+XoAQCDIbOqOsKn/WlNJVzjzObzo5kN+OCve1SknD4jxr3zAgD/QD5k1ODVwuo2
92mAPuZfn8j2IUemXhisUlfJVpW57gw=
=VmVz
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20251110' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
==================
ath.git update for v6.18-rc6
Fix an ath11k transmit status reporting issue. This issue has always
been present, but not reported until recently.
Bringing this through the current release since there is now a
userspace entity that wants to leverage this.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Swap interrupt numbers of eqos because the below commit just swap
interrupt-names and missed swap interrupts also.
The driver (drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c) use
interrupt-names to get irq numbers.
Fixes: f29c19a6e4 ("arm64: dts: imx8dxl-ss-conn: Fix Ethernet interrupt-names order")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Cc: stable@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Breno Leitao says:
====================
net: netpoll: fix memory leak and add comprehensive selftests
Fix a memory leak in netpoll and introduce netconsole selftests that
expose the issue when running with kmemleak detection enabled.
This patchset includes a selftest for netpoll with multiple concurrent
users (netconsole + bonding), which simulates the scenario from test[1]
that originally demonstrated the issue allegedly fixed by commit
efa95b01da ("netpoll: fix use after free") - a commit that is now
being reverted.
Sending this to "net" branch because this is a fix, and the selftest
might help with the backports validation.
Link: https://lore.kernel.org/lkml/96b940137a50e5c387687bb4f57de8b0435a653f.1404857349.git.decot@googlers.com/ [1]
====================
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-0-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds a selftest that verifies netconsole functionality
over bonded network interfaces using netdevsim. It sets up two bonded
interfaces acting as transmit (TX) and receive (RX) ends, placed in
separate network namespaces. The test sends kernel log messages and
verifies that they are properly received on the bonded RX interfaces
with both IPv4 and IPv6, and using basic and extended netconsole
formats.
This patchset aims to test a long-standing netpoll subsystem where
netpoll has multiple users. (in this case netconsole and bonding). A
similar selftest has been discussed in [1] and [2].
This test also tries to enable bonding and netpoll in different order,
just to guarantee that all the possibilities are exercised.
Link: https://lore.kernel.org/all/20250905-netconsole_torture-v3-0-875c7febd316@debian.org/ [1]
Link: https://lore.kernel.org/lkml/96b940137a50e5c387687bb4f57de8b0435a653f.1404857349.git.decot@googlers.com/ [2]
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-4-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Create a netconsole test that puts a lot of pressure on the netconsole
list manipulation. Do it by creating dynamic targets and deleting
targets while messages are being sent. Also put interface down while the
messages are being sent, as creating parallel targets.
The code launches three background jobs on distinct schedules:
* Toggle netcons target every 30 iterations
* create and delete random_target every 50 iterations
* toggle iface every 70 iterations
This creates multiple concurrency sources that interact with netconsole
states. This is good practice to simulate stress, and exercise netpoll
and netconsole locks.
This test already found an issue as reported in [1]
Link: https://lore.kernel.org/all/20250901-netpoll_memleak-v1-1-34a181977dfc@debian.org/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Andre Carvalho <asantostc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-3-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extract the netconsole target creation from create_dynamic_target(), by
moving it from create_dynamic_target() into a new helper function. This
enables other tests to use the creation of netconsole targets with
arbitrary parameters and no sleep.
The new helper will be utilized by forthcoming torture-type selftests
that require dynamic target management.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-2-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit efa95b01da ("netpoll: fix use after free") incorrectly
ignored the refcount and prematurely set dev->npinfo to NULL during
netpoll cleanup, leading to improper behavior and memory leaks.
Scenario causing lack of proper cleanup:
1) A netpoll is associated with a NIC (e.g., eth0) and netdev->npinfo is
allocated, and refcnt = 1
- Keep in mind that npinfo is shared among all netpoll instances. In
this case, there is just one.
2) Another netpoll is also associated with the same NIC and
npinfo->refcnt += 1.
- Now dev->npinfo->refcnt = 2;
- There is just one npinfo associated to the netdev.
3) When the first netpolls goes to clean up:
- The first cleanup succeeds and clears np->dev->npinfo, ignoring
refcnt.
- It basically calls `RCU_INIT_POINTER(np->dev->npinfo, NULL);`
- Set dev->npinfo = NULL, without proper cleanup
- No ->ndo_netpoll_cleanup() is either called
4) Now the second target tries to clean up
- The second cleanup fails because np->dev->npinfo is already NULL.
* In this case, ops->ndo_netpoll_cleanup() was never called, and
the skb pool is not cleaned as well (for the second netpoll
instance)
- This leaks npinfo and skbpool skbs, which is clearly reported by
kmemleak.
Revert commit efa95b01da ("netpoll: fix use after free") and adds
clarifying comments emphasizing that npinfo cleanup should only happen
once the refcount reaches zero, ensuring stable and correct netpoll
behavior.
Cc: <stable@vger.kernel.org> # 3.17.x
Cc: Jay Vosburgh <jv@jvosburgh.net>
Fixes: efa95b01da ("netpoll: fix use after free")
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251107-netconsole_torture-v10-1-749227b55f63@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Aksh Garg says:
====================
Fix IET verification implementation for CPSW driver
The CPSW module supports Intersperse Express Traffic (IET) and allows
the MAC layer to verify whether the peer supports IET through its MAC
merge sublayer, by sending a verification packet and waiting for its
response until the timeout. As defined in IEEE 802.3 Clause 99, the
verification process involves up to 3 verification attempts to
establish support.
This patch series fixes issues in the implementation of this IET
verification process.
====================
Link: https://patch.msgid.link/20251106092305.1437347-1-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The am65_cpsw_iet_verify_wait() function attempts verification 20 times,
toggling the AM65_CPSW_PN_IET_MAC_LINKFAIL bit in each iteration. When
the LINKFAIL bit transitions from 1 to 0, the MAC merge layer initiates
the verification process and waits for the timeout configured in
MAC_VERIFY_CNT before automatically retransmitting. The MAC_VERIFY_CNT
register is configured according to the user-defined verify/response
timeout in am65_cpsw_iet_set_verify_timeout_count(). As per IEEE 802.3
Clause 99, the hardware performs this automatic retry up to 3 times.
Current implementation toggles LINKFAIL after the user-configured
verify/response timeout in each iteration, forcing the hardware to
restart verification instead of respecting the MAC_VERIFY_CNT timeout.
This bypasses the hardware's automatic retry mechanism.
Fix this by moving the LINKFAIL bit toggle outside the retry loop and
reducing the retry count from 20 to 3. The software now only monitors
the status register while the hardware autonomously handles the 3
verification attempts at proper MAC_VERIFY_CNT intervals.
Fixes: 49a2eb9068 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20251106092305.1437347-3-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CPSW module uses the MAC_VERIFY_CNT bit field in the
CPSW_PN_IET_VERIFY_REG_k register to set the verify/response timeout
count. This register specifies the number of clock cycles to wait before
resending a verify packet if the verification fails.
The verify/response timeout count, as being set by the function
am65_cpsw_iet_set_verify_timeout_count() is hardcoded for 125MHz
clock frequency, which varies based on PHY mode and link speed.
The respective clock frequencies are as follows:
- RGMII mode:
* 1000 Mbps: 125 MHz
* 100 Mbps: 25 MHz
* 10 Mbps: 2.5 MHz
- QSGMII/SGMII mode: 125 MHz (all speeds)
Fix this by adding logic to calculate the correct timeout counts
based on the actual PHY interface mode and link speed.
Fixes: 49a2eb9068 ("net: ethernet: ti: am65-cpsw-qos: Add Frame Preemption MAC Merge support")
Signed-off-by: Aksh Garg <a-garg7@ti.com>
Link: https://patch.msgid.link/20251106092305.1437347-2-a-garg7@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In tls_handshake_accept(), a netlink message is allocated using
genlmsg_new(). In the error handling path, genlmsg_cancel() is called
to cancel the message construction, but the message itself is not freed.
This leads to a memory leak.
Fix this by calling nlmsg_free() in the error path after genlmsg_cancel()
to release the allocated memory.
Fixes: 2fd5532044 ("net/handshake: Add a kernel API for requesting a TLSv1.3 handshake")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://patch.msgid.link/20251106144511.3859535-1-zilin@seu.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current CLC proposal message construction uses a mix of
`ini->smc_type_v1/v2` and `pclc_base->hdr.typev1/v2` to decide whether
to include optional extensions (IPv6 prefix extension for v1, and v2
extension). This leads to a critical inconsistency: when
`smc_clc_prfx_set()` fails - for example, in IPv6-only environments with
only link-local addresses, or when the local IP address and the outgoing
interface’s network address are not in the same subnet.
As a result, the proposal message is assembled using the stale
`ini->smc_type_v1` value—causing the IPv6 prefix extension to be
included even though the header indicates v1 is not supported.
The peer then receives a malformed CLC proposal where the header type
does not match the payload, and immediately resets the connection.
The fix ensures consistency between the CLC header flags and the actual
payload by synchronizing `ini->smc_type_v1` with `pclc_base->hdr.typev1`
when prefix setup fails.
Fixes: 8c3dca341a ("net/smc: build and send V2 CLC proposal")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Link: https://patch.msgid.link/20251107024029.88753-1-alibuda@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
netif_carrier_ok() doesn't check if the slave is up. Before the below
commit, netif_running() was also checked.
Fixes: 23a6037ce7 ("bonding: Remove support for use_carrier")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Jay Vosburgh <jv@jvosburgh.net>
Link: https://patch.msgid.link/20251106180252.3974772-1-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When freeing indexed arrays, the corresponding free function should
be called for each entry of the indexed array. For example, for
for 'struct tc_act_attrs' 'tc_act_attrs_free(...)' needs to be called
for each entry.
Previously, memory leaks were reported when enabling the ASAN
analyzer.
=================================================================
==874==ERROR: LeakSanitizer: detected memory leaks
Direct leak of 24 byte(s) in 1 object(s) allocated from:
#0 0x7f221fd20cb5 in malloc ./debug/gcc/gcc/libsanitizer/asan/asan_malloc_linux.cpp:67
#1 0x55c98db048af in tc_act_attrs_set_options_vlan_parms ../generated/tc-user.h:2813
#2 0x55c98db048af in main ./linux/tools/net/ynl/samples/tc-filter-add.c:71
Direct leak of 24 byte(s) in 1 object(s) allocated from:
#0 0x7f221fd20cb5 in malloc ./debug/gcc/gcc/libsanitizer/asan/asan_malloc_linux.cpp:67
#1 0x55c98db04a93 in tc_act_attrs_set_options_vlan_parms ../generated/tc-user.h:2813
#2 0x55c98db04a93 in main ./linux/tools/net/ynl/samples/tc-filter-add.c:74
Direct leak of 10 byte(s) in 2 object(s) allocated from:
#0 0x7f221fd20cb5 in malloc ./debug/gcc/gcc/libsanitizer/asan/asan_malloc_linux.cpp:67
#1 0x55c98db0527d in tc_act_attrs_set_kind ../generated/tc-user.h:1622
SUMMARY: AddressSanitizer: 58 byte(s) leaked in 4 allocation(s).
The following diff illustrates the changes introduced compared to the
previous version of the code.
void tc_flower_attrs_free(struct tc_flower_attrs *obj)
{
+ unsigned int i;
+
free(obj->indev);
+ for (i = 0; i < obj->_count.act; i++)
+ tc_act_attrs_free(&obj->act[i]);
free(obj->act);
free(obj->key_eth_dst);
free(obj->key_eth_dst_mask);
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://patch.msgid.link/20251106151529.453026-3-zahari.doychev@linux.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Broadcom switches locally terminate link local traffic and do not
forward it, so we should not mark it as offloaded.
In some situations we still want/need to flood this traffic, e.g. if STP
is disabled, or it is explicitly enabled via the group_fwd_mask. But if
the skb is marked as offloaded, the kernel will assume this was already
done in hardware, and the packets never reach other bridge ports.
So ensure that link local traffic is never marked as offloaded, so that
the kernel can forward/flood these packets in software if needed.
Since the local termination in not configurable, check the destination
MAC, and never mark packets as offloaded if it is a link local ether
address.
While modern switches set the tag reason code to BRCM_EG_RC_PROT_TERM
for trapped link local traffic, they also set it for link local traffic
that is flooded (01:80:c2:00:00:10 to 01:80:c2:00:00:2f), so we cannot
use it and need to look at the destination address for them as well.
Fixes: 964dbf186e ("net: dsa: tag_brcm: add support for legacy tags")
Fixes: 0e62f543be ("net: dsa: Fix duplicate frames flooded by learning")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20251109134635.243951-1-jonas.gorski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tracing selftest "event-filter-function.tc" was failing because it
first runs the "sample_events" function that triggers the kmem_cache_free
event and it looks at what function was used during a call to "ls".
But the first time it calls this, it could trigger events that are used to
pull pages into the page cache.
The rest of the test uses the function it finds during that call to see if
it will be called in subsequent "sample_events" calls. But if there's no
need to pull pages into the page cache, it will not trigger that function
and the test will fail.
Call the "sample_events" twice to trigger all the page cache work before
it calls it to find a function to use in subsequent checks.
Cc: stable@vger.kernel.org
Fixes: eb50d0f250 ("selftests/ftrace: Choose target function for filter test from samples")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
syzbot reported a possible shift-out-of-bounds [1]
Blamed commit added rto_alpha_max and rto_beta_max set to 1000.
It is unclear if some sctp users are setting very large rto_alpha
and/or rto_beta.
In order to prevent user regression, perform the test at run time.
Also add READ_ONCE() annotations as sysctl values can change under us.
[1]
UBSAN: shift-out-of-bounds in net/sctp/transport.c:509:41
shift exponent 64 is too large for 32-bit type 'unsigned int'
CPU: 0 UID: 0 PID: 16704 Comm: syz.2.2320 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x16c/0x1f0 lib/dump_stack.c:120
ubsan_epilogue lib/ubsan.c:233 [inline]
__ubsan_handle_shift_out_of_bounds+0x27f/0x420 lib/ubsan.c:494
sctp_transport_update_rto.cold+0x1c/0x34b net/sctp/transport.c:509
sctp_check_transmitted+0x11c4/0x1c30 net/sctp/outqueue.c:1502
sctp_outq_sack+0x4ef/0x1b20 net/sctp/outqueue.c:1338
sctp_cmd_process_sack net/sctp/sm_sideeffect.c:840 [inline]
sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1372 [inline]
Fixes: b58537a1f5 ("net: sctp: fix permissions for rto_alpha and rto_beta knobs")
Reported-by: syzbot+f8c46c8b2b7f6e076e99@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/netdev/690c81ae.050a0220.3d0d33.014e.GAE@google.com/T/#u
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20251106111054.3288127-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RISC-V updates for v6.18-rc6, including:
- A fix for a commit in v6.18-rc5 that broke the build on clang
versions earlier than 19 and binutils versions earlier than 2.38.
(This exposed that we're not properly testing earlier toolchain
versions in our linux-next builds and PR submissions. This was
fixed for this PR, and is being addressed more generally for -next
builds.)
- A fix to remove some redundant Makefile code
- A fix to avoid building Canaan Kendryte K210-specific code on targets
that don't build for the K210
-----BEGIN PGP SIGNATURE-----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=nEvc
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
- fix broken clang build on versions earlier than 19 and binutils
versions earlier than 2.38.
(This exposed that we're not properly testing earlier toolchain
versions in our linux-next builds and PR submissions. This was fixed
for this PR, and is being addressed more generally for -next builds.)
- remove some redundant Makefile code
- avoid building Canaan Kendryte K210-specific code on targets that
don't build for the K210
* tag 'riscv-for-linus-6.18-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Fix CONFIG_AS_HAS_INSN for new .insn usage
riscv: Remove redundant judgment for the default build target
riscv: Build loader.bin exclusively for Canaan K210
It's useful to know which query opcodes are available. Extend the
structure and return that. It's a trivial change, and even though it can
be painlessly extended later, it'd still require adding a v2 of the
structure.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The utimes01 and utime06 tests fail when delegated timestamps are
enabled, specifically in subtests that modify the atime and mtime
fields using the 'nobody' user ID.
The problem can be reproduced as follow:
# echo "/media *(rw,no_root_squash,sync)" >> /etc/exports
# export -ra
# mount -o rw,nfsvers=4.2 127.0.0.1:/media /tmpdir
# cd /opt/ltp
# ./runltp -d /tmpdir -s utimes01
# ./runltp -d /tmpdir -s utime06
This issue occurs because nfs_setattr does not verify the inode's
UID against the caller's fsuid when delegated timestamps are
permitted for the inode.
This patch adds the UID check and if it does not match then the
request is sent to the server for permission checking.
Fixes: e12912d941 ("NFSv4: Add support for delegated atime and mtime attributes")
Signed-off-by: Dai Ngo <dai.ngo@oracle.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
Contrary to what was stated on d36349ea73 ("Bluetooth: hci_conn:
Fix running bis_cleanup for hci_conn->type PA_LINK") the PA_LINK does
in fact needs to run bis_cleanup in order to terminate the PA Sync,
since that is bond to the listening socket which is the entity that
controls the lifetime of PA Sync, so if it is closed/released the PA
Sync shall be terminated, terminating the PA Sync shall not result in
the BIG Sync being terminated since once the later is established it
doesn't depend on the former anymore.
If the use user wants to reconnect/rebind a number of BIS(s) it shall
keep the socket open until it no longer needs the PA Sync, which means
it retains full control of the lifetime of both PA and BIG Syncs.
Fixes: d36349ea73 ("Bluetooth: hci_conn: Fix running bis_cleanup for hci_conn->type PA_LINK")
Fixes: a7bcffc673 ("Bluetooth: Add PA_LINK to distinguish BIG sync and PA sync connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
l2cap_chan_close() needs to be called in l2cap_chan_lock(), otherwise
l2cap_le_sig_cmd() etc. may run concurrently.
Add missing locks around l2cap_chan_close().
Fixes: 6b8d4a6a03 ("Bluetooth: 6LoWPAN: Use connected oriented channel instead of fixed one")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
disconnect_all_peers() calls sleeping function (l2cap_chan_close) under
spinlock. Holding the lock doesn't actually do any good -- we work on a
local copy of the list, and the lock doesn't protect against peer->chan
having already been freed.
Fix by taking refcounts of peer->chan instead. Clean up the code and
old comments a bit.
Take devices_lock instead of RCU, because the kfree_rcu();
l2cap_chan_put(); construct in chan_close_cb() does not guarantee
peer->chan is necessarily valid in RCU.
Also take l2cap_chan_lock() which is required for l2cap_chan_close().
Log: (bluez 6lowpan-tester Client Connect - Disable)
------
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:575
...
<TASK>
...
l2cap_send_disconn_req (net/bluetooth/l2cap_core.c:938 net/bluetooth/l2cap_core.c:1495)
...
? __pfx_l2cap_chan_close (net/bluetooth/l2cap_core.c:809)
do_enable_set (net/bluetooth/6lowpan.c:1048 net/bluetooth/6lowpan.c:1068)
------
Fixes: 9030582963 ("Bluetooth: 6lowpan: Converting rwlocks to use RCU")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
l2cap_chan_put() is exported, so export also l2cap_chan_hold() for
modules.
l2cap_chan_hold() has use case in net/bluetooth/6lowpan.c
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth 6lowpan.c confuses BDADDR_LE and ADDR_LE_DEV address types,
e.g. debugfs "connect" command takes the former, and "disconnect" and
"connect" to already connected device take the latter. This is due to
using same value both for l2cap_chan_connect and hci_conn_hash_lookup_le
which take different dst_type values.
Fix address type passed to hci_conn_hash_lookup_le().
Retain the debugfs API difference between "connect" and "disconnect"
commands since it's been like this since 2015 and nobody apparently
complained.
Fixes: f5ad4ffceb ("Bluetooth: 6lowpan: Use hci_conn_hash_lookup_le() when possible")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Bluetooth 6lowpan.c netdev has header_ops, so it must set link-local
header for RX skb, otherwise things crash, eg. with AF_PACKET SOCK_RAW
Add missing skb_reset_mac_header() for uncompressed ipv6 RX path.
For the compressed one, it is done in lowpan_header_decompress().
Log: (BlueZ 6lowpan-tester Client Recv Raw - Success)
------
kernel BUG at net/core/skbuff.c:212!
Call Trace:
<IRQ>
...
packet_rcv (net/packet/af_packet.c:2152)
...
<TASK>
__local_bh_enable_ip (kernel/softirq.c:407)
netif_rx (net/core/dev.c:5648)
chan_recv_cb (net/bluetooth/6lowpan.c:294 net/bluetooth/6lowpan.c:359)
------
Fixes: 18722c2470 ("Bluetooth: Enable 6LoWPAN support for BT LE devices")
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There is a KASAN: slab-use-after-free read in btusb_disconnect().
Calling "usb_driver_release_interface(&btusb_driver, data->intf)" will
free the btusb data associated with the interface. The same data is
then used later in the function, hence the UAF.
Fix by moving the accesses to btusb data to before the data is free'd.
Reported-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2fc81b50a4f8263a159b
Tested-by: syzbot+2fc81b50a4f8263a159b@syzkaller.appspotmail.com
Fixes: fd913ef7ce ("Bluetooth: btusb: Add out-of-band wakeup support")
Signed-off-by: Raphael Pinsonneault-Thibeault <rpthibeault@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
mesh_send_done timer is not canceled when hdev is removed, which causes
crash if the timer triggers after hdev is gone.
Cancel the timer when MGMT removes the hdev, like other MGMT timers.
Should fix the BUG: sporadically seen by BlueZ test bot
(in "Mesh - Send cancel - 1" test).
Log:
------
BUG: KASAN: slab-use-after-free in run_timer_softirq+0x76b/0x7d0
...
Freed by task 36:
kasan_save_stack+0x24/0x50
kasan_save_track+0x14/0x30
__kasan_save_free_info+0x3a/0x60
__kasan_slab_free+0x43/0x70
kfree+0x103/0x500
device_release+0x9a/0x210
kobject_put+0x100/0x1e0
vhci_release+0x18b/0x240
------
Fixes: b338d91703 ("Bluetooth: Implement support for Mesh")
Link: https://lore.kernel.org/linux-bluetooth/67364c09.0c0a0220.113cba.39ff@mx.google.com/
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Smatch static checker noted that in _nfs4_proc_lookupp(), the flag
RPC_TASK_TIMEOUT is being passed as an argument to nfs4_init_sequence(),
which is clearly incorrect.
Since LOOKUPP is an idempotent operation, nfs4_init_sequence() should
not ask the server to cache the result. The RPC_TASK_TIMEOUT flag needs
to be passed down to the RPC layer.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Reported-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Fixes: 76998ebb91 ("NFSv4: Observe the NFS_MOUNT_SOFTREVAL flag in _nfs4_proc_lookupp")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
If adding the second kobject fails, drop both references to avoid sysfs
residue and memory leak.
Fixes: e96f9268ee ("NFS: Make all of /sys/fs/nfs network-namespace unique")
Signed-off-by: Yang Xiuwei <yangxiuwei@kylinos.cn>
Reviewed-by: Benjamin Coddington <ben.coddington@hammerspace.com>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
When nfs_do_create() returns an EEXIST error, it means that a regular
file could not be created. That could mean that a symlink needs to be
resolved. If that's the case, a lookup needs to be kicked off.
Reported-by: Stephen Abbene <sabbene87@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220710
Fixes: 7c6c5249f0 ("NFS: add atomic_open for NFSv3 to handle O_TRUNC correctly.")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: NeilBrown <neil@brown.name>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
From https://lore.kernel.org/linux-nfs/aQHASIumLJyOoZGH@infradead.org/
On Wed, Oct 29, 2025 at 12:20:40AM -0700, Christoph Hellwig wrote:
> On Mon, Oct 27, 2025 at 12:18:30PM -0400, Mike Snitzer wrote:
> > LOCALIO's misaligned DIO will issue head/tail followed by O_DIRECT
> > middle (via AIO completion of that aligned middle). So out of order
> > relative to file offset.
>
> That's in general a really bad idea. It will obviously work, but
> both on SSDs and out of place write file systems it is a sure way
> to increase your garbage collection overhead a lot down the line.
Fix this by never issuing misaligned DIO out of order. This fix means
the DIO-aligned middle will only use AIO completion if there is no
misaligned end segment. Otherwise, all 3 segments of a misaligned DIO
will be issued without AIO completion to ensure file offset increases
properly for all partial READ or WRITE situations.
Factoring out nfs_local_iter_setup() helps standardize repetitive
nfs_local_iters_setup_dio() code and is inspired by cleanup work that
Chuck Lever did on the NFSD Direct code.
Fixes: c817248fc8 ("nfs/localio: add proper O_DIRECT support for READ and WRITE")
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Anna Schumaker <anna.schumaker@oracle.com>
