The SBSA UART device tree bindings require a current-speed property that
specifies the baud rate configured by the firmware. Add it on Jetson AGX
Orin and Jetson Orin Nano/NX.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Google Pixel C has a JDI LPM102A188A display panel, so add a
DT node for it.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Google Pixel C has a TI LP8557 backlight controller, so add a
DT node for it.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the node for the DSI/CSI regulator in the Pixel C.
Signed-off-by: Diogo Ivo <diogo.ivo@tecnico.ulisboa.pt>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the iommu property to the host1x node to register it with its
swgroup.
Signed-off-by: Rayyan Ansari <rayyan@ansari.sh>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The QSPI device used on Jetson Orin NX and Nano modules (p3767) is
the same as Jetson AGX Orin (p3701) and should have a maximum speed of
102 MHz.
Fixes: 13b0aca303 ("arm64: tegra: Support Jetson Orin NX")
Signed-off-by: Brad Griffis <bgriffis@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SD card detect pin is active-low on all Orin Nano and NX SKUs that
have an SD card slot.
Fixes: 13b0aca303 ("arm64: tegra: Support Jetson Orin NX")
Signed-off-by: Brad Griffis <bgriffis@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Commit 546dea18c9 ("nvme-auth: check chap ctrl_key once constructed")
replaced the condition "if (ctrl->ctrl_key)" (indicating bidirectional
auth) by "if (chap->ctrl_key)", because ctrl->ctrl_key is a resource shared
with sysfs. But chap->ctrl_key is set in
nvme_auth_process_dhchap_challenge() depending on the DHVLEN in the
DH-HMAC-CHAP Challenge message received from the controller, and will thus
be non-NULL for every DH-HMAC-CHAP exchange, even if unidirectional auth
was requested. This will lead to a protocol violation by sending a Success2
message in the unidirectional case (per NVMe base spec 2.0, the
authentication transaction ends after the Success1 message for
unidirectional auth). Use chap->s2 instead, which is non-zero if and only
if the host requested bi-directional authentication from the controller.
Fixes: 546dea18c9 ("nvme-auth: check chap ctrl_key once constructed")
Signed-off-by: Martin Wilck <mwilck@suse.com>
Reviewed-by: Daniel Wagner <dwagner@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
From Alon:
"Due to a logical bug in the NVMe-oF/TCP subsystem in the Linux kernel,
a malicious user can cause a UAF and a double free, which may lead to
RCE (may also lead to an LPE in case the attacker already has local
privileges)."
Hence, when a queue initialization fails after the ahash requests are
allocated, it is guaranteed that the queue removal async work will be
called, hence leave the deallocation to the queue removal.
Also, be extra careful not to continue processing the socket, so set
queue rcv_state to NVMET_TCP_RECV_ERR upon a socket error.
Cc: stable@vger.kernel.org
Reported-by: Alon Zahavi <zahavi.alon@gmail.com>
Tested-by: Alon Zahavi <zahavi.alon@gmail.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Add comments for nlpid, family, udlen and udata in struct nft_table, and
afinfo is no longer a member of struct nft_table, so remove the comment
for it.
Signed-off-by: George Guo <guodongtai@kylinos.cn>
Signed-off-by: Florian Westphal <fw@strlen.de>
pr_debug doesn't provide any information other than that a packet
did not match existing state but also was found to not create a new
connection.
Replaces this with tcp_error_log, which will also dump packets'
content so one can see if this is a stray FIN or RST.
Signed-off-by: Florian Westphal <fw@strlen.de>
nf_conntrack_alter_reply doesn't do helper reassignment anymore.
Remove the comments that make this claim.
Furthermore, remove dead code from the function and place ot
in nf_conntrack.h.
Signed-off-by: Florian Westphal <fw@strlen.de>
Since struct netlink_callback::args is not used by rule dumpers anymore,
use it to hold nft_rule_dump_ctx. Add a build-time check to make sure it
won't ever exceed the available space.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
In order to move the context into struct netlink_callback's scratch
area, the latter must be unused first.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
This relieves the dump callback from having to check nlmsg_type upon
each call and instead performs the check once in .start callback.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
None of the dump callbacks uses netlink_callback::args beyond the first
element, no need to zero the data.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
SRCU callbacks acceleration might fail if the preceding callbacks
advance also fails. This can happen when the following steps are met:
1) The RCU_WAIT_TAIL segment has callbacks (say for gp_num 8) and the
RCU_NEXT_READY_TAIL also has callbacks (say for gp_num 12).
2) The grace period for RCU_WAIT_TAIL is observed as started but not yet
completed so rcu_seq_current() returns 4 + SRCU_STATE_SCAN1 = 5.
3) This value is passed to rcu_segcblist_advance() which can't move
any segment forward and fails.
4) srcu_gp_start_if_needed() still proceeds with callback acceleration.
But then the call to rcu_seq_snap() observes the grace period for the
RCU_WAIT_TAIL segment (gp_num 8) as completed and the subsequent one
for the RCU_NEXT_READY_TAIL segment as started
(ie: 8 + SRCU_STATE_SCAN1 = 9) so it returns a snapshot of the
next grace period, which is 16.
5) The value of 16 is passed to rcu_segcblist_accelerate() but the
freshly enqueued callback in RCU_NEXT_TAIL can't move to
RCU_NEXT_READY_TAIL which already has callbacks for a previous grace
period (gp_num = 12). So acceleration fails.
6) Note in all these steps, srcu_invoke_callbacks() hadn't had a chance
to run srcu_invoke_callbacks().
Then some very bad outcome may happen if the following happens:
7) Some other CPU races and starts the grace period number 16 before the
CPU handling previous steps had a chance. Therefore srcu_gp_start()
isn't called on the latter sdp to fix the acceleration leak from
previous steps with a new pair of call to advance/accelerate.
8) The grace period 16 completes and srcu_invoke_callbacks() is finally
called. All the callbacks from previous grace periods (8 and 12) are
correctly advanced and executed but callbacks in RCU_NEXT_READY_TAIL
still remain. Then rcu_segcblist_accelerate() is called with a
snaphot of 20.
9) Since nothing started the grace period number 20, callbacks stay
unhandled.
This has been reported in real load:
[3144162.608392] INFO: task kworker/136:12:252684 blocked for more
than 122 seconds.
[3144162.615986] Tainted: G O K 5.4.203-1-tlinux4-0011.1 #1
[3144162.623053] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs"
disables this message.
[3144162.631162] kworker/136:12 D 0 252684 2 0x90004000
[3144162.631189] Workqueue: kvm-irqfd-cleanup irqfd_shutdown [kvm]
[3144162.631192] Call Trace:
[3144162.631202] __schedule+0x2ee/0x660
[3144162.631206] schedule+0x33/0xa0
[3144162.631209] schedule_timeout+0x1c4/0x340
[3144162.631214] ? update_load_avg+0x82/0x660
[3144162.631217] ? raw_spin_rq_lock_nested+0x1f/0x30
[3144162.631218] wait_for_completion+0x119/0x180
[3144162.631220] ? wake_up_q+0x80/0x80
[3144162.631224] __synchronize_srcu.part.19+0x81/0xb0
[3144162.631226] ? __bpf_trace_rcu_utilization+0x10/0x10
[3144162.631227] synchronize_srcu+0x5f/0xc0
[3144162.631236] irqfd_shutdown+0x3c/0xb0 [kvm]
[3144162.631239] ? __schedule+0x2f6/0x660
[3144162.631243] process_one_work+0x19a/0x3a0
[3144162.631244] worker_thread+0x37/0x3a0
[3144162.631247] kthread+0x117/0x140
[3144162.631247] ? process_one_work+0x3a0/0x3a0
[3144162.631248] ? __kthread_cancel_work+0x40/0x40
[3144162.631250] ret_from_fork+0x1f/0x30
Fix this with taking the snapshot for acceleration _before_ the read
of the current grace period number.
The only side effect of this solution is that callbacks advancing happen
then _after_ the full barrier in rcu_seq_snap(). This is not a problem
because that barrier only cares about:
1) Ordering accesses of the update side before call_srcu() so they don't
bleed.
2) See all the accesses prior to the grace period of the current gp_num
The only things callbacks advancing need to be ordered against are
carried by snp locking.
Reported-by: Yong He <alexyonghe@tencent.com>
Co-developed-by:: Yong He <alexyonghe@tencent.com>
Signed-off-by: Yong He <alexyonghe@tencent.com>
Co-developed-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Co-developed-by: Neeraj upadhyay <Neeraj.Upadhyay@amd.com>
Signed-off-by: Neeraj upadhyay <Neeraj.Upadhyay@amd.com>
Link: http://lore.kernel.org/CANZk6aR+CqZaqmMWrC2eRRPY12qAZnDZLwLnHZbNi=xXMB401g@mail.gmail.com
Fixes: da915ad5cf ("srcu: Parallelize callback handling")
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
It will move into struct netlink_callback's scratch area later, just put
nf_tables_dump_rules_start in shape to reduce churn later.
Suggested-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Florian Westphal <fw@strlen.de>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20231006224343.441720-1-robh@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
To convert the sprd-sc9860 driver, make sprd_pinctrl_remove()
return void (instead of zero) and use .remove_new as callback.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009162510.335208-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
To convert all those qcom pinctrl drivers, make msm_pinctrl_remove()
return void (instead of zero) and use .remove_new in all drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009162510.335208-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
To convert all those qcom pinctrl drivers, make msm_pinctrl_remove()
return void (instead of zero) and use .remove_new in all drivers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009162510.335208-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_platform_ioremap_resource() and platform_get_irq() print
the error messages themselves and our "failed" one brings no value
and just noise. Refactor code to avoid those noisy error messages.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231006105803.3374241-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The acpi_evaluate_dsm_typed() provides a way to check the type of the
object evaluated by _DSM call. Use it instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20231002135103.2602847-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-17-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-16-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-15-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-14-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231009083856.222030-12-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-11-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Link: https://lore.kernel.org/r/20231009083856.222030-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231009083856.222030-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ti_iodelay_remove() is only called after ti_iodelay_probe() completed
successfully. In this case platform_set_drvdata() was called with a
non-NULL argument and so platform_get_drvdata() won't return NULL.
Simplify by removing the if block with the always false condition.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pcs_remove() is only called after pcs_probe() completed successfully. In
this case platform_set_drvdata() was called with a non-NULL argument and
so platform_get_drvdata() won't return NULL.
Simplify by removing the if block with the always false condition.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver core has no handling for errors returned by the .remove()
callback. The only action on error is a dev_warn() with generic error
message that the returned value is returned.
Replace it by a more specific and useful message. Then returning zero is
the right thing to do, the only effect is to suppress the core's
warning.
This prepares the driver for the conversion to .remove_new().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20231009083856.222030-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 5f521494cc.
The patch breaks mounts with security mount options like
$ mount -o context=system_u:object_r:root_t:s0 /dev/sdX /mn
mount: /mnt: wrong fs type, bad option, bad superblock on /dev/sdX, missing codepage or helper program, ...
We cannot reject all unknown options in btrfs_parse_subvol_options() as
intended, the security options can be present at this point and it's not
possible to enumerate them in a future proof way. This means unknown
mount options are silently accepted like before when the filesystem is
mounted with either -o subvol=/path or as followup mounts of the same
device.
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com
Signed-off-by: David Sterba <dsterba@suse.com>
Commit 1e66220948 ("net/mlx5e: Update rx ring hw mtu upon each rx-fcs
flag change") seems to have accidentally inverted the logic added in
commit 0bc73ad46a ("net/mlx5e: Mutually exclude RX-FCS and
RX-port-timestamp").
The impact of this is a little unclear since it seems the FCS scattered
with RX-FCS is (usually?) correct regardless.
Fixes: 1e66220948 ("net/mlx5e: Update rx ring hw mtu upon each rx-fcs flag change")
Tested-by: Charlotte Tan <charlotte@extrahop.com>
Reviewed-by: Charlotte Tan <charlotte@extrahop.com>
Cc: Adham Faris <afaris@nvidia.com>
Cc: Aya Levin <ayal@nvidia.com>
Cc: Tariq Toukan <tariqt@nvidia.com>
Cc: Moshe Shemesh <moshe@nvidia.com>
Cc: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Will Mortensen <will@extrahop.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20231006053706.514618-1-will@extrahop.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver might pull connectors which weren't submitted by
user-space into the atomic state. For instance,
intel_dp_mst_atomic_master_trans_check() pulls in connectors
sharing the same DP-MST stream. However, if the connector is
unregistered, this later fails with:
[ 559.425658] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset] [CONNECTOR:378:DP-7] is not registered
Skip the unregistered connector check to allow user-space to turn
off connectors one-by-one.
See this wlroots issue:
https://gitlab.freedesktop.org/wlroots/wlroots/-/issues/3407
Previous discussion:
https://lore.kernel.org/intel-gfx/Y6GX7z17WmDSKwta@ideak-desk.fi.intel.com/
Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231005131623.114379-1-contact@emersion.fr
The imx7d-pico-pi board does not have an SD card slot
connected to the USDHC1 port. Only eMMC and Wifi SDIO ports
are used.
Disable the USDHC1 node.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per fsl-dcp.yaml, passing "fsl,imx28-dcp", "fsl,imx23-dcp" is not
valid.
Change it to pass only "fsl,imx28-dcp" to fix the following
schema warning:
crypto@80028000: compatible: 'oneOf' conditional failed, one must be fixed:
['fsl,imx28-dcp', 'fsl,imx23-dcp'] is too long
'fsl,imx28-dcp' is not one of ['fsl,imx6sl-dcp', 'fsl,imx6ull-dcp']
'fsl,imx28-dcp' was expected
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
