commit b9bd10c434 upstream.
When a queue is unbound from the vfio_ap device driver, it is reset to
ensure its crypto data is not leaked when it is bound to another device
driver. If the queue is unbound due to the fact that the adapter or domain
was removed from the host's AP configuration, then attempting to reset it
will fail with response code 01 (APID not valid) getting returned from the
reset command. Let's ensure that the queue is assigned to the host's
configuration before resetting it.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: "Jason J. Herne" <jjherne@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: eeb386aeb5 ("s390/vfio-ap: handle config changed and scan complete notification")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115185441.31526-7-akrowiak@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f009cfa466 upstream.
When a queue is unbound from the vfio_ap device driver, if that queue is
assigned to a guest's AP configuration, its associated adapter is removed
because queues are defined to a guest via a matrix of adapters and
domains; so, it is not possible to remove a single queue.
If an adapter is removed from the guest's AP configuration, all associated
queues must be reset to prevent leaking crypto data should any of them be
assigned to a different guest or device driver. The one caveat is that if
the queue is being removed because the adapter or domain has been removed
from the host's AP configuration, then an attempt to reset the queue will
fail with response code 01, AP-queue number not valid; so resetting these
queues should be skipped.
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Fixes: 09d31ff787 ("s390/vfio-ap: hot plug/unplug of AP devices when probed/removed")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115185441.31526-6-akrowiak@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f848cba767 upstream.
When filtering the adapters from the configuration profile for a guest to
create or update a guest's AP configuration, if the APID of an adapter and
the APQI of a domain identify a queue device that is not bound to the
vfio_ap device driver, the APID of the adapter will be filtered because an
individual APQN can not be filtered due to the fact the APQNs are assigned
to an AP configuration as a matrix of APIDs and APQIs. Consequently, a
guest will not have access to all of the queues associated with the
filtered adapter. If the queues are subsequently made available again to
the guest, they should re-appear in a reset state; so, let's make sure all
queues associated with an adapter unplugged from the guest are reset.
In order to identify the set of queues that need to be reset, let's allow a
vfio_ap_queue object to be simultaneously stored in both a hashtable and a
list: A hashtable used to store all of the queues assigned
to a matrix mdev; and/or, a list used to store a subset of the queues that
need to be reset. For example, when an adapter is hot unplugged from a
guest, all guest queues associated with that adapter must be reset. Since
that may be a subset of those assigned to the matrix mdev, they can be
stored in a list that can be passed to the vfio_ap_mdev_reset_queues
function.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 48cae940c3 ("s390/vfio-ap: refresh guest's APCB by filtering AP resources assigned to mdev")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115185441.31526-5-akrowiak@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 774d10196e upstream.
When adapters and/or domains are added to the host's AP configuration, this
may result in multiple queue devices getting created and probed by the
vfio_ap device driver. For each queue device probed, the matrix of adapters
and domains assigned to a matrix mdev will be filtered to update the
guest's APCB. If any adapters or domains get added to or removed from the
APCB, the guest's AP configuration will be dynamically updated (i.e., hot
plug/unplug). To dynamically update the guest's configuration, its VCPUs
must be taken out of SIE for the period of time it takes to make the
update. This is disruptive to the guest's operation and if there are many
queues probed due to a change in the host's AP configuration, this could be
troublesome. The problem is exacerbated by the fact that the
'on_scan_complete' callback also filters the mdev's matrix and updates
the guest's AP configuration.
In order to reduce the potential amount of disruption to the guest that may
result from a change to the host's AP configuration, let's bypass the
filtering of the matrix and updating of the guest's AP configuration in the
probe callback - if due to a host config change - and defer it until the
'on_scan_complete' callback is invoked after the AP bus finishes its device
scan operation. This way the filtering and updating will be performed only
once regardless of the number of queues added.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 48cae940c3 ("s390/vfio-ap: refresh guest's APCB by filtering AP resources assigned to mdev")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115185441.31526-4-akrowiak@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 16fb78cbf5 upstream.
While filtering the mdev matrix, it doesn't make sense - and will have
unexpected results - to filter an APID from the matrix if the APID or one
of the associated APQIs is not in the host's AP configuration. There are
two reasons for this:
1. An adapter or domain that is not in the host's AP configuration can be
assigned to the matrix; this is known as over-provisioning. Queue
devices, however, are only created for adapters and domains in the
host's AP configuration, so there will be no queues associated with an
over-provisioned adapter or domain to filter.
2. The adapter or domain may have been externally removed from the host's
configuration via an SE or HMC attached to a DPM enabled LPAR. In this
case, the vfio_ap device driver would have been notified by the AP bus
via the on_config_changed callback and the adapter or domain would
have already been filtered.
Since the matrix_mdev->shadow_apcb.apm and matrix_mdev->shadow_apcb.aqm are
copied from the mdev matrix sans the APIDs and APQIs not in the host's AP
configuration, let's loop over those bitmaps instead of those assigned to
the matrix.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 48cae940c3 ("s390/vfio-ap: refresh guest's APCB by filtering AP resources assigned to mdev")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115185441.31526-3-akrowiak@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 850fb7fa8c upstream.
The vfio_ap_mdev_filter_matrix function is called whenever a new adapter or
domain is assigned to the mdev. The purpose of the function is to update
the guest's AP configuration by filtering the matrix of adapters and
domains assigned to the mdev. When an adapter or domain is assigned, only
the APQNs associated with the APID of the new adapter or APQI of the new
domain are inspected. If an APQN does not reference a queue device bound to
the vfio_ap device driver, then it's APID will be filtered from the mdev's
matrix when updating the guest's AP configuration.
Inspecting only the APID of the new adapter or APQI of the new domain will
result in passing AP queues through to a guest that are not bound to the
vfio_ap device driver under certain circumstances. Consider the following:
guest's AP configuration (all also assigned to the mdev's matrix):
14.0004
14.0005
14.0006
16.0004
16.0005
16.0006
unassign domain 4
unbind queue 16.0005
assign domain 4
When domain 4 is re-assigned, since only domain 4 will be inspected, the
APQNs that will be examined will be:
14.0004
16.0004
Since both of those APQNs reference queue devices that are bound to the
vfio_ap device driver, nothing will get filtered from the mdev's matrix
when updating the guest's AP configuration. Consequently, queue 16.0005
will get passed through despite not being bound to the driver. This
violates the linux device model requirement that a guest shall only be
given access to devices bound to the device driver facilitating their
pass-through.
To resolve this problem, every adapter and domain assigned to the mdev will
be inspected when filtering the mdev's matrix.
Signed-off-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Fixes: 48cae940c3 ("s390/vfio-ap: refresh guest's APCB by filtering AP resources assigned to mdev")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240115185441.31526-2-akrowiak@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b2d039da6 upstream.
In the vfio_ap_irq_enable function, after the page containing the
notification indicator byte (NIB) is pinned, the function attempts
to register the guest ISC. If registration fails, the function sets the
status response code and returns without unpinning the page containing
the NIB. In order to avoid a memory leak, the NIB should be unpinned before
returning from the vfio_ap_irq_enable function.
Co-developed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Anthony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Fixes: 783f0a3ccd ("s390/vfio-ap: add s390dbf logging to the vfio_ap_irq_enable function")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231109164427.460493-2-akrowiak@linux.ibm.com
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix virtual vs physical address confusion in Storage Class Memory
(SCM) block device driver.
- Fix saving and restoring of FPU kernel context, which could lead
to corruption of vector registers 8-15.
- Update defconfigs.
-----BEGIN PGP SIGNATURE-----
iI0EABYIADUWIQQrtrZiYVkVzKQcYivNdxKlNrRb8AUCZYL8uxccYWdvcmRlZXZA
bGludXguaWJtLmNvbQAKCRDNdxKlNrRb8BlUAQDEWcaTXoHbuLEZ8DN9lVHLryOW
ACOFFLpPFlIjVj+eCwD+Ir4xzVdWOCImtNlMbsdrIcribmuzezl4nJ001Jhi6QE=
=o5b2
-----END PGP SIGNATURE-----
Merge tag 's390-6.7-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Alexander Gordeev:
- Fix virtual vs physical address confusion in Storage Class Memory
(SCM) block device driver.
- Fix saving and restoring of FPU kernel context, which could lead to
corruption of vector registers 8-15
- Update defconfigs
* tag 's390-6.7-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390: update defconfigs
s390/vx: fix save/restore of fpu kernel context
s390/scm: fix virtual vs physical address confusion
Fix virtual vs physical address confusion (which currently are the same).
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----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=EShg
-----END PGP SIGNATURE-----
Merge tag 'block-6.7-2023-11-23' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
"A bit bigger than usual at this time, but nothing really earth
shattering:
- NVMe pull request via Keith:
- TCP TLS fixes (Hannes)
- Authentifaction fixes (Mark, Hannes)
- Properly terminate target names (Christoph)
- MD pull request via Song, fixing a raid5 corruption issue
- Disentanglement of the dependency mess in nvme introduced with the
tls additions. Now it should actually build on all configs (Arnd)
- Series of bcache fixes (Coly)
- Removal of a dead helper (Damien)
- s390 dasd fix (Muhammad, Jan)
- lockdep blk-cgroup fixes (Ming)"
* tag 'block-6.7-2023-11-23' of git://git.kernel.dk/linux: (33 commits)
nvme: tcp: fix compile-time checks for TLS mode
nvme: target: fix Kconfig select statements
nvme: target: fix nvme_keyring_id() references
nvme: move nvme_stop_keep_alive() back to original position
nbd: pass nbd_sock to nbd_read_reply() instead of index
s390/dasd: protect device queue against concurrent access
s390/dasd: resolve spelling mistake
block/null_blk: Fix double blk_mq_start_request() warning
nvmet-tcp: always initialize tls_handshake_tmo_work
nvmet: nul-terminate the NQNs passed in the connect command
nvme: blank out authentication fabrics options if not configured
nvme: catch errors from nvme_configure_metadata()
nvme-tcp: only evaluate 'tls' option if TLS is selected
nvme-auth: set explanation code for failure2 msgs
nvme-auth: unlock mutex in one place only
block: Remove blk_set_runtime_active()
nbd: fix null-ptr-dereference while accessing 'nbd->config'
nbd: factor out a helper to get nbd_config without holding 'config_lock'
nbd: fold nbd config initialization into nbd_alloc_config()
bcache: avoid NULL checking to c->root in run_cache_set()
...
In dasd_profile_start() the amount of requests on the device queue are
counted. The access to the device queue is unprotected against
concurrent access. With a lot of parallel I/O, especially with alias
devices enabled, the device queue can change while dasd_profile_start()
is accessing the queue. In the worst case this leads to a kernel panic
due to incorrect pointer accesses.
Fix this by taking the device lock before accessing the queue and
counting the requests. Additionally the check for a valid profile data
pointer can be done earlier to avoid unnecessary locking in a hot path.
Cc: <stable@vger.kernel.org>
Fixes: 4fa52aa7a8 ("[S390] dasd: add enhanced DASD statistics interface")
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Link: https://lore.kernel.org/r/20231025132437.1223363-3-sth@linux.ibm.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since commit a72178cfe8 ("net/smc: Fix dependency of SMC on ISM")
you can build the ism code without selecting the SMC network protocol.
That leaves some ism functions be reported as unused. Move these
functions under the conditional compile with CONFIG_SMC.
Also codify the suggestion to also configure the SMC protocol in ism's
Kconfig - but with an "imply" rather than a "select" as SMC depends on
other config options and allow for a deliberate decision not to build
SMC. Also, mention that in ISM's help.
Fixes: a72178cfe8 ("net/smc: Fix dependency of SMC on ISM")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/netdev/afd142a2-1fa0-46b9-8b2d-7652d41d3ab8@infradead.org/
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- sched: fix SKB_NOT_DROPPED_YET splat under debug config
Current release - new code bugs:
- tcp: fix usec timestamps with TCP fastopen
- tcp_sigpool: fix some off by one bugs
- tcp: fix possible out-of-bounds reads in tcp_hash_fail()
- tcp: fix SYN option room calculation for TCP-AO
- bpf: fix compilation error without CGROUPS
- ptp:
- ptp_read() should not release queue
- fix tsevqs corruption
Previous releases - regressions:
- llc: verify mac len before reading mac header
Previous releases - always broken:
- bpf:
- fix check_stack_write_fixed_off() to correctly spill imm
- fix precision tracking for BPF_ALU | BPF_TO_BE | BPF_END
- check map->usercnt after timer->timer is assigned
- dsa: lan9303: consequently nested-lock physical MDIO
- dccp/tcp: call security_inet_conn_request() after setting IP addr
- tg3: fix the TX ring stall due to incorrect full ring handling
- phylink: initialize carrier state at creation
- ice: fix direction of VF rules in switchdev mode
Misc:
- fill in a bunch of missing MODULE_DESCRIPTION()s, more to come
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=k6Wk
-----END PGP SIGNATURE-----
Merge tag 'net-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter and bpf.
Current release - regressions:
- sched: fix SKB_NOT_DROPPED_YET splat under debug config
Current release - new code bugs:
- tcp:
- fix usec timestamps with TCP fastopen
- fix possible out-of-bounds reads in tcp_hash_fail()
- fix SYN option room calculation for TCP-AO
- tcp_sigpool: fix some off by one bugs
- bpf: fix compilation error without CGROUPS
- ptp:
- ptp_read() should not release queue
- fix tsevqs corruption
Previous releases - regressions:
- llc: verify mac len before reading mac header
Previous releases - always broken:
- bpf:
- fix check_stack_write_fixed_off() to correctly spill imm
- fix precision tracking for BPF_ALU | BPF_TO_BE | BPF_END
- check map->usercnt after timer->timer is assigned
- dsa: lan9303: consequently nested-lock physical MDIO
- dccp/tcp: call security_inet_conn_request() after setting IP addr
- tg3: fix the TX ring stall due to incorrect full ring handling
- phylink: initialize carrier state at creation
- ice: fix direction of VF rules in switchdev mode
Misc:
- fill in a bunch of missing MODULE_DESCRIPTION()s, more to come"
* tag 'net-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (84 commits)
net: ti: icss-iep: fix setting counter value
ptp: fix corrupted list in ptp_open
ptp: ptp_read should not release queue
net_sched: sch_fq: better validate TCA_FQ_WEIGHTS and TCA_FQ_PRIOMAP
net: kcm: fill in MODULE_DESCRIPTION()
net/sched: act_ct: Always fill offloading tuple iifidx
netfilter: nat: fix ipv6 nat redirect with mapped and scoped addresses
netfilter: xt_recent: fix (increase) ipv6 literal buffer length
ipvs: add missing module descriptions
netfilter: nf_tables: remove catchall element in GC sync path
netfilter: add missing module descriptions
drivers/net/ppp: use standard array-copy-function
net: enetc: shorten enetc_setup_xdp_prog() error message to fit NETLINK_MAX_FMTMSG_LEN
virtio/vsock: Fix uninit-value in virtio_transport_recv_pkt()
r8169: respect userspace disabling IFF_MULTICAST
selftests/bpf: get trusted cgrp from bpf_iter__cgroup directly
bpf: Let verifier consider {task,cgroup} is trusted in bpf_iter_reg
net: phylink: initialize carrier state at creation
test/vsock: add dobule bind connect test
test/vsock: refactor vsock_accept
...
Replace 'weed' with 'we' in the comment.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A secure execution (SE, also known as confidential computing)
guest may see asynchronous errors on a crypto firmware queue.
The current implementation to gather information about cards
and queues in ap_queue_info() simple returns if an asynchronous
error is hanging on the firmware queue. If such a situation
happened and it was the only queue visible for a crypto card
within an SE guest, then the card vanished from sysfs as
the AP bus scan function refuses to hold a card without any
type information. As lszcrypt evaluates the sysfs such
a card vanished from the lszcrypt card listing and the
user is baffled and has no way to reset and thus clear the
pending asynchronous error.
This patch improves the named function to also evaluate GR2
of the TAPQ in case of asynchronous error pending. If there
is a not-null value stored in, the info is processed now.
In the end, a queue with pending asynchronous error does not
lead to a vanishing card any more.
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
If a card or a queue is in check-stop state, it can't be used by
applications to perform crypto operations. Applications check the 'online'
sysfs attribute to check if a card or queue is usable.
Report a card or queue as offline in case it is in check-stop state.
Furthermore, don't allow to set a card or queue online, if it is in
check-stop state.
This is similar to when the card or the queue is in deconfigured state,
there it is also reported as being offline, and it can't be set online.
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Fix kernel crash in AP bus code caused by very early invocation of the
config change callback function via SCLP.
After a fresh IML of the machine the crypto cards are still offline and
will get switched online only with activation of any LPAR which has the
card in it's configuration. A crypto card coming online is reported
to the LPAR via SCLP and the AP bus offers a callback function to get
this kind of information. However, it may happen that the callback is
invoked before the AP bus init function is complete. As the callback
triggers a synchronous AP bus scan, the scan may already run but some
internal states are not initialized by the AP bus init function resulting
in a crash like this:
[ 11.635859] Unable to handle kernel pointer dereference in virtual kernel address space
[ 11.635861] Failing address: 0000000000000000 TEID: 0000000000000887
[ 11.635862] Fault in home space mode while using kernel ASCE.
[ 11.635864] AS:00000000894c4007 R3:00000001fece8007 S:00000001fece7800 P:000000000000013d
[ 11.635879] Oops: 0004 ilc:1 [#1] SMP
[ 11.635882] Modules linked in:
[ 11.635884] CPU: 5 PID: 42 Comm: kworker/5:0 Not tainted 6.6.0-rc3-00003-g4dbf7cdc6b42 #12
[ 11.635886] Hardware name: IBM 3931 A01 751 (LPAR)
[ 11.635887] Workqueue: events_long ap_scan_bus
[ 11.635891] Krnl PSW : 0704c00180000000 0000000000000000 (0x0)
[ 11.635895] R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
[ 11.635897] Krnl GPRS: 0000000001000a00 0000000000000000 0000000000000006 0000000089591940
[ 11.635899] 0000000080000000 0000000000000a00 0000000000000000 0000000000000000
[ 11.635901] 0000000081870c00 0000000089591000 000000008834e4e2 0000000002625a00
[ 11.635903] 0000000081734200 0000038000913c18 000000008834c6d6 0000038000913ac8
[ 11.635906] Krnl Code:>0000000000000000: 0000 illegal
[ 11.635906] 0000000000000002: 0000 illegal
[ 11.635906] 0000000000000004: 0000 illegal
[ 11.635906] 0000000000000006: 0000 illegal
[ 11.635906] 0000000000000008: 0000 illegal
[ 11.635906] 000000000000000a: 0000 illegal
[ 11.635906] 000000000000000c: 0000 illegal
[ 11.635906] 000000000000000e: 0000 illegal
[ 11.635915] Call Trace:
[ 11.635916] [<0000000000000000>] 0x0
[ 11.635918] [<000000008834e4e2>] ap_queue_init_state+0x82/0xb8
[ 11.635921] [<000000008834ba1c>] ap_scan_domains+0x6fc/0x740
[ 11.635923] [<000000008834c092>] ap_scan_adapter+0x632/0x8b0
[ 11.635925] [<000000008834c3e4>] ap_scan_bus+0xd4/0x288
[ 11.635927] [<00000000879a33ba>] process_one_work+0x19a/0x410
[ 11.635930] Discipline DIAG cannot be used without z/VM
[ 11.635930] [<00000000879a3a2c>] worker_thread+0x3fc/0x560
[ 11.635933] [<00000000879aea60>] kthread+0x120/0x128
[ 11.635936] [<000000008792afa4>] __ret_from_fork+0x3c/0x58
[ 11.635938] [<00000000885ebe62>] ret_from_fork+0xa/0x30
[ 11.635942] Last Breaking-Event-Address:
[ 11.635942] [<000000008834c6d4>] ap_wait+0xcc/0x148
This patch improves the ap_bus_force_rescan() function which is
invoked by the config change callback by checking if a first
initial AP bus scan has been done. If not, the force rescan request
is simple ignored. Anyhow it does not make sense to trigger AP bus
re-scans even before the very first bus scan is complete.
Cc: stable@vger.kernel.org
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This patch introduces some code lines which check
for interrupt support enabled on an AP queue after
a reply has been received. This invocation has been
chosen as there is a good chance to have the queue
empty at that time. As the enablement of the irq
imples a state machine change the queue should not
have any pending requests or unreceived replies.
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This patch reworks the irq handling and reporting code
for the AP queue interrupt handling to always use the
irq info from the queue status.
Until now the interrupt status of an AP queue was stored
into a bool variable within the ap_queue struct. This
variable was set on a successful interrupt enablement
and cleared with kicking a reset. However, it may be
that the interrupt state is manipulated outband for
example by a hypervisor. This patch removes this variable
and instead the irq bit from the AP queue status which is
always reflecting the current irq state is used.
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
- Get rid of private VM_FAULT flags
- Add word-at-a-time implementation
- Add DCACHE_WORD_ACCESS support
- Cleanup control register handling
- Disallow CPU hotplug of CPU 0 to simplify its handling complexity,
following a similar restriction in x86
- Optimize pai crypto map allocation
- Update the list of crypto express EP11 coprocessor operation modes
- Fixes and improvements for secure guests AP pass-through
- Several fixes to address incorrect page marking for address translation
with the "cmma no-dat" feature, preventing potential incorrect guest
TLB flushes
- Fix early IPI handling
- Several virtual vs physical address confusion fixes
- Various small fixes and improvements all over the code
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmVFLkYACgkQjYWKoQLX
FBgxRwf9FSNFwLcbYbG1x94rUUHnbaiyJWCezp3/ypr+m+qDvQatLYc75SxwrH0y
ocSygqvtVryVkWAKKvOHF1Kg5R2Fedmzf5wuVTXglfPqE1ZgMGdwS/LtknIoz556
twZJIpFzUFt5xaljpTCZJanLMvy/npl0bilezhNGl6v7N5rsWLbfK6vsPMDm+TTZ
yscapOsk8Z16NjXq0FETS5JHG65jjj9rkRfb0qD8SOFhti0fR9MSP2xeRXrDMDZE
IWXog5usx2DS6VX2HnxA8O7z1hhuTccJ1K1+rYqbb0Fwccqi7QaGZXEvocYEvlvy
lVe3/jbyn27hUoypHcfVCAVxdoOrnw==
=SMOp
-----END PGP SIGNATURE-----
Merge tag 's390-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Get rid of private VM_FAULT flags
- Add word-at-a-time implementation
- Add DCACHE_WORD_ACCESS support
- Cleanup control register handling
- Disallow CPU hotplug of CPU 0 to simplify its handling complexity,
following a similar restriction in x86
- Optimize pai crypto map allocation
- Update the list of crypto express EP11 coprocessor operation modes
- Fixes and improvements for secure guests AP pass-through
- Several fixes to address incorrect page marking for address
translation with the "cmma no-dat" feature, preventing potential
incorrect guest TLB flushes
- Fix early IPI handling
- Several virtual vs physical address confusion fixes
- Various small fixes and improvements all over the code
* tag 's390-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (74 commits)
s390/cio: replace deprecated strncpy with strscpy
s390/sclp: replace deprecated strncpy with strtomem
s390/cio: fix virtual vs physical address confusion
s390/cio: export CMG value as decimal
s390: delete the unused store_prefix() function
s390/cmma: fix handling of swapper_pg_dir and invalid_pg_dir
s390/cmma: fix detection of DAT pages
s390/sclp: handle default case in sclp memory notifier
s390/pai_crypto: remove per-cpu variable assignement in event initialization
s390/pai: initialize event count once at initialization
s390/pai_crypto: use PERF_ATTACH_TASK define for per task detection
s390/mm: add missing arch_set_page_dat() call to gmap allocations
s390/mm: add missing arch_set_page_dat() call to vmem_crst_alloc()
s390/cmma: fix initial kernel address space page table walk
s390/diag: add missing virt_to_phys() translation to diag224()
s390/mm,fault: move VM_FAULT_ERROR handling to do_exception()
s390/mm,fault: remove VM_FAULT_BADMAP and VM_FAULT_BADACCESS
s390/mm,fault: remove VM_FAULT_SIGNAL
s390/mm,fault: remove VM_FAULT_BADCONTEXT
s390/mm,fault: simplify kfence fault handling
...
Core & protocols
----------------
- Support usec resolution of TCP timestamps, enabled selectively by
a route attribute.
- Defer regular TCP ACK while processing socket backlog, try to send
a cumulative ACK at the end. Increase single TCP flow performance
on a 200Gbit NIC by 20% (100Gbit -> 120Gbit).
- The Fair Queuing (FQ) packet scheduler:
- add built-in 3 band prio / WRR scheduling
- support bypass if the qdisc is mostly idle (5% speed up for TCP RR)
- improve inactive flow reporting
- optimize the layout of structures for better cache locality
- Support TCP Authentication Option (RFC 5925, TCP-AO), a more modern
replacement for the old MD5 option.
- Add more retransmission timeout (RTO) related statistics to TCP_INFO.
- Support sending fragmented skbs over vsock sockets.
- Make sure we send SIGPIPE for vsock sockets if socket was shutdown().
- Add sysctl for ignoring lower limit on lifetime in Router
Advertisement PIO, based on an in-progress IETF draft.
- Add sysctl to control activation of TCP ping-pong mode.
- Add sysctl to make connection timeout in MPTCP configurable.
- Support rcvlowat and notsent_lowat on MPTCP sockets, to help apps
limit the number of wakeups.
- Support netlink GET for MDB (multicast forwarding), allowing user
space to request a single MDB entry instead of dumping the entire
table.
- Support selective FDB flushing in the VXLAN tunnel driver.
- Allow limiting learned FDB entries in bridges, prevent OOM attacks.
- Allow controlling via configfs netconsole targets which were created
via the kernel cmdline at boot, rather than via configfs at runtime.
- Support multiple PTP timestamp event queue readers with different
filters.
- MCTP over I3C.
BPF
---
- Add new veth-like netdevice where BPF program defines the logic
of the xmit routine. It can operate in L3 and L2 mode.
- Support exceptions - allow asserting conditions which should
never be true but are hard for the verifier to infer.
With some extra flexibility around handling of the exit / failure.
https://lwn.net/Articles/938435/
- Add support for local per-cpu kptr, allow allocating and storing
per-cpu objects in maps. Access to those objects operates on
the value for the current CPU. This allows to deprecate local
one-off implementations of per-CPU storage like
BPF_MAP_TYPE_PERCPU_CGROUP_STORAGE maps.
- Extend cgroup BPF sockaddr hooks for UNIX sockets. The use case is
for systemd to re-implement the LogNamespace feature which allows
running multiple instances of systemd-journald to process the logs
of different services.
- Enable open-coded task_vma iteration, after maple tree conversion
made it hard to directly walk VMAs in tracing programs.
- Add open-coded task, css_task and css iterator support.
One of the use cases is customizable OOM victim selection via BPF.
- Allow source address selection with bpf_*_fib_lookup().
- Add ability to pin BPF timer to the current CPU.
- Prevent creation of infinite loops by combining tail calls and
fentry/fexit programs.
- Add missed stats for kprobes to retrieve the number of missed kprobe
executions and subsequent executions of BPF programs.
- Inherit system settings for CPU security mitigations.
- Add BPF v4 CPU instruction support for arm32 and s390x.
Changes to common code
----------------------
- overflow: add DEFINE_FLEX() for on-stack definition of structs
with flexible array members.
- Process doc update with more guidance for reviewers.
Driver API
----------
- Simplify locking in WiFi (cfg80211 and mac80211 layers), use wiphy
mutex in most places and remove a lot of smaller locks.
- Create a common DPLL configuration API. Allow configuring
and querying state of PLL circuits used for clock syntonization,
in network time distribution.
- Unify fragmented and full page allocation APIs in page pool code.
Let drivers be ignorant of PAGE_SIZE.
- Rework PHY state machine to avoid races with calls to phy_stop().
- Notify DSA drivers of MAC address changes on user ports, improve
correctness of offloads which depend on matching port MAC addresses.
- Allow antenna control on injected WiFi frames.
- Reduce the number of variants of napi_schedule().
- Simplify error handling when composing devlink health messages.
Misc
----
- A lot of KCSAN data race "fixes", from Eric.
- A lot of __counted_by() annotations, from Kees.
- A lot of strncpy -> strscpy and printf format fixes.
- Replace master/slave terminology with conduit/user in DSA drivers.
- Handful of KUnit tests for netdev and WiFi core.
Removed
-------
- AppleTalk COPS.
- AppleTalk ipddp.
- TI AR7 CPMAC Ethernet driver.
Drivers
-------
- Ethernet high-speed NICs:
- Intel (100G, ice, idpf):
- add a driver for the Intel E2000 IPUs
- make CRC/FCS stripping configurable
- cross-timestamping for E823 devices
- basic support for E830 devices
- use aux-bus for managing client drivers
- i40e: report firmware versions via devlink
- nVidia/Mellanox:
- support 4-port NICs
- increase max number of channels to 256
- optimize / parallelize SF creation flow
- Broadcom (bnxt):
- enhance NIC temperature reporting
- support PAM4 speeds and lane configuration
- Marvell OcteonTX2:
- PTP pulse-per-second output support
- enable hardware timestamping for VFs
- Solarflare/AMD:
- conntrack NAT offload and offload for tunnels
- Wangxun (ngbe/txgbe):
- expose HW statistics
- Pensando/AMD:
- support PCI level reset
- narrow down the condition under which skbs are linearized
- Netronome/Corigine (nfp):
- support CHACHA20-POLY1305 crypto in IPsec offload
- Ethernet NICs embedded, slower, virtual:
- Synopsys (stmmac):
- add Loongson-1 SoC support
- enable use of HW queues with no offload capabilities
- enable PPS input support on all 5 channels
- increase TX coalesce timer to 5ms
- RealTek USB (r8152): improve efficiency of Rx by using GRO frags
- xen: support SW packet timestamping
- add drivers for implementations based on TI's PRUSS (AM64x EVM)
- nVidia/Mellanox Ethernet datacenter switches:
- avoid poor HW resource use on Spectrum-4 by better block selection
for IPv6 multicast forwarding and ordering of blocks in ACL region
- Ethernet embedded switches:
- Microchip:
- support configuring the drive strength for EMI compliance
- ksz9477: partial ACL support
- ksz9477: HSR offload
- ksz9477: Wake on LAN
- Realtek:
- rtl8366rb: respect device tree config of the CPU port
- Ethernet PHYs:
- support Broadcom BCM5221 PHYs
- TI dp83867: support hardware LED blinking
- CAN:
- add support for Linux-PHY based CAN transceivers
- at91_can: clean up and use rx-offload helpers
- WiFi:
- MediaTek (mt76):
- new sub-driver for mt7925 USB/PCIe devices
- HW wireless <> Ethernet bridging in MT7988 chips
- mt7603/mt7628 stability improvements
- Qualcomm (ath12k):
- WCN7850:
- enable 320 MHz channels in 6 GHz band
- hardware rfkill support
- enable IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS
to make scan faster
- read board data variant name from SMBIOS
- QCN9274: mesh support
- RealTek (rtw89):
- TDMA-based multi-channel concurrency (MCC)
- Silicon Labs (wfx):
- Remain-On-Channel (ROC) support
- Bluetooth:
- ISO: many improvements for broadcast support
- mark BCM4378/BCM4387 as BROKEN_LE_CODED
- add support for QCA2066
- btmtksdio: enable Bluetooth wakeup from suspend
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=46nS
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Support usec resolution of TCP timestamps, enabled selectively by a
route attribute.
- Defer regular TCP ACK while processing socket backlog, try to send
a cumulative ACK at the end. Increase single TCP flow performance
on a 200Gbit NIC by 20% (100Gbit -> 120Gbit).
- The Fair Queuing (FQ) packet scheduler:
- add built-in 3 band prio / WRR scheduling
- support bypass if the qdisc is mostly idle (5% speed up for TCP RR)
- improve inactive flow reporting
- optimize the layout of structures for better cache locality
- Support TCP Authentication Option (RFC 5925, TCP-AO), a more modern
replacement for the old MD5 option.
- Add more retransmission timeout (RTO) related statistics to
TCP_INFO.
- Support sending fragmented skbs over vsock sockets.
- Make sure we send SIGPIPE for vsock sockets if socket was
shutdown().
- Add sysctl for ignoring lower limit on lifetime in Router
Advertisement PIO, based on an in-progress IETF draft.
- Add sysctl to control activation of TCP ping-pong mode.
- Add sysctl to make connection timeout in MPTCP configurable.
- Support rcvlowat and notsent_lowat on MPTCP sockets, to help apps
limit the number of wakeups.
- Support netlink GET for MDB (multicast forwarding), allowing user
space to request a single MDB entry instead of dumping the entire
table.
- Support selective FDB flushing in the VXLAN tunnel driver.
- Allow limiting learned FDB entries in bridges, prevent OOM attacks.
- Allow controlling via configfs netconsole targets which were
created via the kernel cmdline at boot, rather than via configfs at
runtime.
- Support multiple PTP timestamp event queue readers with different
filters.
- MCTP over I3C.
BPF:
- Add new veth-like netdevice where BPF program defines the logic of
the xmit routine. It can operate in L3 and L2 mode.
- Support exceptions - allow asserting conditions which should never
be true but are hard for the verifier to infer. With some extra
flexibility around handling of the exit / failure:
https://lwn.net/Articles/938435/
- Add support for local per-cpu kptr, allow allocating and storing
per-cpu objects in maps. Access to those objects operates on the
value for the current CPU.
This allows to deprecate local one-off implementations of per-CPU
storage like BPF_MAP_TYPE_PERCPU_CGROUP_STORAGE maps.
- Extend cgroup BPF sockaddr hooks for UNIX sockets. The use case is
for systemd to re-implement the LogNamespace feature which allows
running multiple instances of systemd-journald to process the logs
of different services.
- Enable open-coded task_vma iteration, after maple tree conversion
made it hard to directly walk VMAs in tracing programs.
- Add open-coded task, css_task and css iterator support. One of the
use cases is customizable OOM victim selection via BPF.
- Allow source address selection with bpf_*_fib_lookup().
- Add ability to pin BPF timer to the current CPU.
- Prevent creation of infinite loops by combining tail calls and
fentry/fexit programs.
- Add missed stats for kprobes to retrieve the number of missed
kprobe executions and subsequent executions of BPF programs.
- Inherit system settings for CPU security mitigations.
- Add BPF v4 CPU instruction support for arm32 and s390x.
Changes to common code:
- overflow: add DEFINE_FLEX() for on-stack definition of structs with
flexible array members.
- Process doc update with more guidance for reviewers.
Driver API:
- Simplify locking in WiFi (cfg80211 and mac80211 layers), use wiphy
mutex in most places and remove a lot of smaller locks.
- Create a common DPLL configuration API. Allow configuring and
querying state of PLL circuits used for clock syntonization, in
network time distribution.
- Unify fragmented and full page allocation APIs in page pool code.
Let drivers be ignorant of PAGE_SIZE.
- Rework PHY state machine to avoid races with calls to phy_stop().
- Notify DSA drivers of MAC address changes on user ports, improve
correctness of offloads which depend on matching port MAC
addresses.
- Allow antenna control on injected WiFi frames.
- Reduce the number of variants of napi_schedule().
- Simplify error handling when composing devlink health messages.
Misc:
- A lot of KCSAN data race "fixes", from Eric.
- A lot of __counted_by() annotations, from Kees.
- A lot of strncpy -> strscpy and printf format fixes.
- Replace master/slave terminology with conduit/user in DSA drivers.
- Handful of KUnit tests for netdev and WiFi core.
Removed:
- AppleTalk COPS.
- AppleTalk ipddp.
- TI AR7 CPMAC Ethernet driver.
Drivers:
- Ethernet high-speed NICs:
- Intel (100G, ice, idpf):
- add a driver for the Intel E2000 IPUs
- make CRC/FCS stripping configurable
- cross-timestamping for E823 devices
- basic support for E830 devices
- use aux-bus for managing client drivers
- i40e: report firmware versions via devlink
- nVidia/Mellanox:
- support 4-port NICs
- increase max number of channels to 256
- optimize / parallelize SF creation flow
- Broadcom (bnxt):
- enhance NIC temperature reporting
- support PAM4 speeds and lane configuration
- Marvell OcteonTX2:
- PTP pulse-per-second output support
- enable hardware timestamping for VFs
- Solarflare/AMD:
- conntrack NAT offload and offload for tunnels
- Wangxun (ngbe/txgbe):
- expose HW statistics
- Pensando/AMD:
- support PCI level reset
- narrow down the condition under which skbs are linearized
- Netronome/Corigine (nfp):
- support CHACHA20-POLY1305 crypto in IPsec offload
- Ethernet NICs embedded, slower, virtual:
- Synopsys (stmmac):
- add Loongson-1 SoC support
- enable use of HW queues with no offload capabilities
- enable PPS input support on all 5 channels
- increase TX coalesce timer to 5ms
- RealTek USB (r8152): improve efficiency of Rx by using GRO frags
- xen: support SW packet timestamping
- add drivers for implementations based on TI's PRUSS (AM64x EVM)
- nVidia/Mellanox Ethernet datacenter switches:
- avoid poor HW resource use on Spectrum-4 by better block
selection for IPv6 multicast forwarding and ordering of blocks
in ACL region
- Ethernet embedded switches:
- Microchip:
- support configuring the drive strength for EMI compliance
- ksz9477: partial ACL support
- ksz9477: HSR offload
- ksz9477: Wake on LAN
- Realtek:
- rtl8366rb: respect device tree config of the CPU port
- Ethernet PHYs:
- support Broadcom BCM5221 PHYs
- TI dp83867: support hardware LED blinking
- CAN:
- add support for Linux-PHY based CAN transceivers
- at91_can: clean up and use rx-offload helpers
- WiFi:
- MediaTek (mt76):
- new sub-driver for mt7925 USB/PCIe devices
- HW wireless <> Ethernet bridging in MT7988 chips
- mt7603/mt7628 stability improvements
- Qualcomm (ath12k):
- WCN7850:
- enable 320 MHz channels in 6 GHz band
- hardware rfkill support
- enable IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS to
make scan faster
- read board data variant name from SMBIOS
- QCN9274: mesh support
- RealTek (rtw89):
- TDMA-based multi-channel concurrency (MCC)
- Silicon Labs (wfx):
- Remain-On-Channel (ROC) support
- Bluetooth:
- ISO: many improvements for broadcast support
- mark BCM4378/BCM4387 as BROKEN_LE_CODED
- add support for QCA2066
- btmtksdio: enable Bluetooth wakeup from suspend"
* tag 'net-next-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1816 commits)
net: pcs: xpcs: Add 2500BASE-X case in get state for XPCS drivers
net: bpf: Use sockopt_lock_sock() in ip_sock_set_tos()
net: mana: Use xdp_set_features_flag instead of direct assignment
vxlan: Cleanup IFLA_VXLAN_PORT_RANGE entry in vxlan_get_size()
iavf: delete the iavf client interface
iavf: add a common function for undoing the interrupt scheme
iavf: use unregister_netdev
iavf: rely on netdev's own registered state
iavf: fix the waiting time for initial reset
iavf: in iavf_down, don't queue watchdog_task if comms failed
iavf: simplify mutex_trylock+sleep loops
iavf: fix comments about old bit locks
doc/netlink: Update schema to support cmd-cnt-name and cmd-max-name
tools: ynl: introduce option to process unknown attributes or types
ipvlan: properly track tx_errors
netdevsim: Block until all devices are released
nfp: using napi_build_skb() to replace build_skb()
net: dsa: microchip: ksz9477: Fix spelling mistake "Enery" -> "Energy"
net: dsa: microchip: Ensure Stable PME Pin State for Wake-on-LAN
net: dsa: microchip: Refactor switch shutdown routine for WoL preparation
...
Convert dasd to use bdev_open_by_path() and pass the handle around.
CC: linux-s390@vger.kernel.org
CC: Christian Borntraeger <borntraeger@linux.ibm.com>
CC: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230927093442.25915-14-jack@suse.cz
Signed-off-by: Christian Brauner <brauner@kernel.org>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect both `params` and `id` to be NUL-terminated based on their
usage with format strings:
format_node_data(iuparams, iunodeid, &lir->incident_node);
format_node_data(auparams, aunodeid, &lir->attached_node);
switch (lir->iq.class) {
case LIR_IQ_CLASS_DEGRADED:
pr_warn("Link degraded: RS=%02x RSID=%04x IC=%02x "
"IUPARAMS=%s IUNODEID=%s AUPARAMS=%s AUNODEID=%s\n",
sei_area->rs, sei_area->rsid, lir->ic, iuparams,
iunodeid, auparams, aunodeid);
NUL-padding is not required as both `params` and `id` have been memset
to 0:
memset(params, 0, PARAMS_LEN);
memset(id, 0, NODEID_LEN);
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Note that there's no overread bugs in the current implementation as the
string literal "n/a" has a size much smaller than PARAMS_LEN or
NODEID_LEN. Nonetheless, let's favor strscpy().
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231023-strncpy-drivers-s390-cio-chsc-c-v1-1-8b76a7b83260@google.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Fix virtual vs physical address confusion (which currently are the
same).
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Change format of the "cmg" sysfs attribute from hex to decimal to
make it easier to consume. Note that this should not break any existing
users since only values 2 and 3 are currently exported. Also the main
user already assumes decimal notation [1].
[1] https://sourceforge.net/p/sblim/gather/ci/master/tree/plugin/metriczCH.c
Reviewed-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When new memory notifier types are added in common code and
unimplemented on s390, return success instead of EINVAL return code.
This prevents breakage when new memory notifier types are added.
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sumanth Korikkar <sumanthk@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect new_entry->dbf_name to be NUL-terminated based on its use with
strcmp():
| if (strcmp(entry->dbf_name, name) == 0) {
Moreover, NUL-padding is not required as new_entry is kzalloc'd just
before this assignment:
| new_entry = kzalloc(sizeof(struct qeth_dbf_entry), GFP_KERNEL);
... rendering any future NUL-byte assignments (like the ones strncpy()
does) redundant.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Tested-by: Thorsten Winkler <twinkler@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231023-strncpy-drivers-s390-net-qeth_core_main-c-v1-1-e7ce65454446@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
We expect chid to be NUL-terminated based on its use with format
strings:
CTCM_DBF_TEXT_(SETUP, CTC_DBF_INFO, "%s(%s) %s", CTCM_FUNTAIL,
chid, ok ? "OK" : "failed");
Moreover, NUL-padding is not required as it is _only_ used in this one
instance with a format string.
Considering the above, a suitable replacement is `strscpy` [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding.
We can also drop the +1 from chid's declaration as we no longer need to
be cautious about leaving a spot for a NUL-byte. Let's use the more
idiomatic strscpy usage of (dest, src, sizeof(dest)) as this more
closely ties the destination buffer to the length.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Tested-by: Thorsten Winkler <twinkler@linux.ibm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20231023-strncpy-drivers-s390-net-ctcm_main-c-v1-1-265db6e78165@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
- Fix IOMMU bitmap allocation in s390 PCI to avoid out of bounds access
when IOMMU pages aren't a multiple of 64.
- Fix kasan crashes when accessing DCSS mapping in memory holes by adding
corresponding kasan zero shadow mappings.
- Fix a memory leak in css_alloc_subchannel in case dma_set_coherent_mask
fails.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAmUzm4wACgkQjYWKoQLX
FBhLVAgAkgucCi+fUdQbmvU80cshWz0+eMG/fKLT5Xkg1sOxRhmy3qkmNtkb9471
WcrplvSP0QjGvoBtKSC0Qme7oZlYTUjUss1jLxzV3y/KAR4G8WAdoMbpKB6bIOzn
S0Sy0WelU9+bUBimxz+ZbdcQKbah/1uFdXqOJueX5YJQZko6hGE9VP+KQ7rKeE/E
ie5h4UjLY64xwXTn4BxkYd0iTqrHYhZ2RaDO+c6yoqTZ+RSH7v71Q3RYxx4jgSTW
uMyHnRknjMia8ms696EDqzAH2FZy15vhOCSc64zeccujE3o0ETB3ZVPBg9fr9s+F
Yc3KFKqrJehSgxFeCCXHG8wQJyzLgQ==
=3nJs
-----END PGP SIGNATURE-----
Merge tag 's390-6.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Vasily Gorbik:
- Fix IOMMU bitmap allocation in s390 PCI to avoid out of bounds access
when IOMMU pages aren't a multiple of 64
- Fix kasan crashes when accessing DCSS mapping in memory holes by
adding corresponding kasan zero shadow mappings
- Fix a memory leak in css_alloc_subchannel in case
dma_set_coherent_mask fails
* tag 's390-6.6-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: fix iommu bitmap allocation
s390/kasan: handle DCSS mapping in memory holes
s390/cio: fix a memleak in css_alloc_subchannel
With Secure Execution the error reply RX 0x8B now carries
an APFS value indicating why the request has been filtered
by a lower layer of the firmware. So display this value
as a warning line in the s390 debug feature trace.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
This patch introduces a new AP queue internal attribute
se_bound which reflects the bound state of an APQN within
a Secure Execution environment.
With introduction of Secure Execution guests now an
AP firmware queue needs to be bound to the guest before
usage. This patch introduces a new internal attribute
reflecting this bound state and some glue code to handle
this new field during lifetime of an AP queue device.
Together with that now the zcrypt scheduler considers
the state of the AP queues when a message is about to be
distributed among the existing queues. There is a new
function ap_queue_usable() which returns true only when
all conditions for using this AP queue device are fulfilled.
In details this means: the AP queue needs to be configured,
not checkstopped and within an SE environment it needs
to be bound. So the new function gives and indication
if the AP queue device is ready to serve requests or not.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
On a state toggle from config off to config on and on the
state toggle from checkstop to not checkstop the queue's
internal states was set but the state machine was not
nudged. This did not care as on the first enqueue of a
request the state machine kick ran.
However, within an Secure Execution guest a queue is
only chosen by the scheduler when it has been bound.
But to bind a queue, it needs to run through the initial
states (reset, enable interrupts, ...). So this is like
a chicken-and-egg problem and the result was in fact
that a queue was unusable after a config off/on toggle.
With some slight rework of the handling of these states
now the new function _ap_queue_init_state() is called
which is the core of the ap_queue_init_state() function
but without locking handling. This has the benefit that
it can be called on all the places where a (re-)init
of the AP queue's state machine is needed.
Fixes: 2d72eaf036 ("s390/ap: implement SE AP bind, unbind and associate")
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Holger Dengler <dengler@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When dma_set_coherent_mask() fails, sch->lock has not been
freed, which is allocated in css_sch_create_locks(), leading
to a memleak.
Fixes: 4520a91a97 ("s390/cio: use dma helpers for setting masks")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Message-Id: <20230921071412.13806-1-dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/linux-s390/bd38baa8-7b9d-4d89-9422-7e943d626d6e@linux.ibm.com/
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
When the SMC protocol is built into the kernel proper while ISM is
configured to be built as module, linking the kernel fails due to
unresolved dependencies out of net/smc/smc_ism.o to
ism_get_smcd_ops, ism_register_client, and ism_unregister_client
as reported via the linux-next test automation (see link).
This however is a bug introduced a while ago.
Correct the dependency list in ISM's and SMC's Kconfig to reflect the
dependencies that are actually inverted. With this you cannot build a
kernel with CONFIG_SMC=y and CONFIG_ISM=m. Either ISM needs to be 'y',
too - or a 'n'. That way, SMC can still be configured on non-s390
architectures that do not have (nor need) an ISM driver.
Fixes: 89e7d2ba61 ("net/ism: Add new API for client registration")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/linux-next/d53b5b50-d894-4df8-8969-fd39e63440ae@infradead.org/
Co-developed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/r/20231006125847.1517840-1-gbayer@linux.ibm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When device_register() fails, zfcp_port_release() will be called after
put_device(). As a result, zfcp_ccw_adapter_put() will be called twice: one
in zfcp_port_release() and one in the error path after device_register().
So the reference on the adapter object is doubly put, which may lead to a
premature free. Fix this by adjusting the error tag after
device_register().
Fixes: f3450c7b91 ("[SCSI] zfcp: Replace local reference counting with common kref")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20230923103723.10320-1-dinghao.liu@zju.edu.cn
Acked-by: Benjamin Block <bblock@linux.ibm.com>
Cc: stable@vger.kernel.org # v2.6.33+
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use control register bit defines instead of plain numbers where
possible.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Convert all single control register usages of __local_ctl_load() and
__local_ctl_store() to local_ctl_load() and local_ctl_store().
This also requires to change the type of some struct lowcore members
from __u64 to unsigned long.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add local and system prefix to some functions to clarify they change
control register contents on either the local CPU or the on all CPUs.
This results in the following API:
Two defines which load and save multiple control registers.
The defines correlate with the following C prototypes:
void __local_ctl_load(unsigned long *, unsigned int cr_low, unsigned int cr_high);
void __local_ctl_store(unsigned long *, unsigned int cr_low, unsigned int cr_high);
Two functions which locally set or clear one bit for a specified
control register:
void local_ctl_set_bit(unsigned int cr, unsigned int bit);
void local_ctl_clear_bit(unsigned int cr, unsigned int bit);
Two functions which set or clear one bit for a specified control
register on all CPUs:
void system_ctl_set_bit(unsigned int cr, unsigned int bit);
void system_ctl_clear_bit(unsigend int cr, unsigned int bit);
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Rename ctl_reg.h to ctlreg.h so it matches not only ctlreg.c but also
other control register related function, union, and structure names,
which all come with a ctlreg prefix.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Control register handling has nothing to do with low level SMP code.
Move it to a separate file.
Reviewed-by: Alexander Gordeev <agordeev@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add additional operation mode strings into the EP11 operation mode table.
These strings are returned by sysfs entries /sys/devices/ap/cardxx/op_modes
and /sys/devices/ap/cardxx/xx.yyyy/op_modes.
Signed-off-by: Ingo Franzki <ifranzki@linux.ibm.com>
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAmT7NSUQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpuIuEACxQj0JjIVwgp8VlUcMAEFap7GH940qs8is
tnRrGS48G/z3WZ0zizGQ1hF2m9oOJ1NwZ1bBrGJlVBP8KSgyR9IxI6WVt0JBZgg8
DNQt+v5FoX4v5ZbFr/NTqz/6YnPWVwyTkJs4JIi9YLmpKkd58N+51n3wl56xyrp7
8OcjHPH1ZI0qGar2poPXI7EKaweSzJW7nr3/cHujYoCfAGn7eZbHNgY0wdAtWdhM
oGFABgMKTFKA0rCSaP8uo7GIqov+KXvFUNOuC6eNjtaUvXMecPLEJxvDhhi52fml
LEH1a9bmtazu6bufrbI2D4SmXLNBcqnQw5d/1pn9oRO/UU6AAi6E7I/L1iodKWav
bkr2i+YMnhUqVDFRwy+j78bcGRlLPWupvj68RdpvAvzhdW/85p9nH66CJfTnjQ3q
xJJKoUREd/8C6ktm5xHYyETxcL5q6Vdz1w5GmsCyOWWpsXsEbh0GHn6pRDkLWJf4
OQhO4CbxIARGE5NRK8MYl/J/581yS1cIdGZAg7hsVHzTGDSt3h/Hlh6ONpWCcvXD
SJI39W83oBSOnsbRG4FU6Bnt/WHTD0yi07cr867l9HEq63JOK/OduMjXA/tdRfwP
fZU3RfFYcS8+h9UHgrSgvCk03fCjq1HsWCDfpc6sUuRG1fH6jSNFdkCKqhCoU9Py
K2IKi1IE0Q==
=4SLW
-----END PGP SIGNATURE-----
Merge tag 'block-6.6-2023-09-08' of git://git.kernel.dk/linux
Pull block fixes from Jens Axboe:
- Fix null_blk polled IO timeout handling (Chengming)
- Regression fix for swapped arguments in drbd bvec_set_page()
(Christoph)
- String length handling fix for s390 dasd (Heiko)
- Fixes for blk-throttle accounting (Yu)
- Fix page pinning issue for same page segments (Christoph)
- Remove redundant file_remove_privs() call (Christoph)
- Fix a regression in partition handling for devices not supporting
partitions (Li)
* tag 'block-6.6-2023-09-08' of git://git.kernel.dk/linux:
drbd: swap bvec_set_page len and offset
block: fix pin count management when merging same-page segments
null_blk: fix poll request timeout handling
s390/dasd: fix string length handling
block: don't add or resize partition on the disk with GENHD_FL_NO_PART
block: remove the call to file_remove_privs in blkdev_write_iter
blk-throttle: consider 'carryover_ios/bytes' in throtl_trim_slice()
blk-throttle: use calculate_io/bytes_allowed() for throtl_trim_slice()
blk-throttle: fix wrong comparation while 'carryover_ios/bytes' is negative
blk-throttle: print signed value 'carryover_bytes/ios' for user
- Couple of virtual vs physical address confusion fixes
- Rework locking in dcssblk driver to address a lockdep warning
- Remove support for "noexec" kernel command line option since there
is no use case where it would make sense
- Simplify kernel mapping setup and get rid of quite a bit of code
- Add architecture specific __set_memory_yy() functions which allow to
modify kernel mappings. Unlike the set_memory_xx() variants they
take void pointer start and end parameters, which allows to use them
without the usual casts, and also to use them on areas larger than
8TB.
Note that the set_memory_xx() family comes with an int num_pages
parameter which overflows with 8TB. This could be addressed by
changing the num_pages parameter to unsigned long, however requires
to change all architectures, since the module code expects an int
parameter (see module_set_memory()).
This was indeed an issue since for debug_pagealloc() we call
set_memory_4k() on the whole identity mapping. Therefore address
this for now with the __set_memory_yy() variant, and address common
code later
- Use dev_set_name() and also fix memory leak in zcrypt driver error
handling
- Remove unused lsi_mask from airq_struct
- Add warning for invalid kernel mapping requests
-----BEGIN PGP SIGNATURE-----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=+iSZ
-----END PGP SIGNATURE-----
Merge tag 's390-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- A couple of virtual vs physical address confusion fixes
- Rework locking in dcssblk driver to address a lockdep warning
- Remove support for "noexec" kernel command line option since there is
no use case where it would make sense
- Simplify kernel mapping setup and get rid of quite a bit of code
- Add architecture specific __set_memory_yy() functions which allow us
to modify kernel mappings. Unlike the set_memory_xx() variants they
take void pointer start and end parameters, which allows using them
without the usual casts, and also to use them on areas larger than
8TB.
Note that the set_memory_xx() family comes with an int num_pages
parameter which overflows with 8TB. This could be addressed by
changing the num_pages parameter to unsigned long, however requires
to change all architectures, since the module code expects an int
parameter (see module_set_memory()).
This was indeed an issue since for debug_pagealloc() we call
set_memory_4k() on the whole identity mapping. Therefore address this
for now with the __set_memory_yy() variant, and address common code
later
- Use dev_set_name() and also fix memory leak in zcrypt driver error
handling
- Remove unused lsi_mask from airq_struct
- Add warning for invalid kernel mapping requests
* tag 's390-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/vmem: do not silently ignore mapping limit
s390/zcrypt: utilize dev_set_name() ability to use a formatted string
s390/zcrypt: don't leak memory if dev_set_name() fails
s390/mm: fix MAX_DMA_ADDRESS physical vs virtual confusion
s390/airq: remove lsi_mask from airq_struct
s390/mm: use __set_memory() variants where useful
s390/set_memory: add __set_memory() variant
s390/set_memory: generate all set_memory() functions
s390/mm: improve description of mapping permissions of prefix pages
s390/amode31: change type of __samode31, __eamode31, etc
s390/mm: simplify kernel mapping setup
s390: remove "noexec" option
s390/vmem: fix virtual vs physical address confusion
s390/dcssblk: fix lockdep warning
s390/monreader: fix virtual vs physical address confusion
With the dev_set_name() prototype it's not obvious that it takes
a formatted string as a parameter. Use its facility instead of
duplicating the same with strncpy()/snprintf() calls.
With this, also prevent return error code to be shadowed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230831110000.24279-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported issues.
The last bit of cleanups from Jiri and the tty structure size reduction
came in last week, a bit late but as they were just style changes and
size reductions, I figured they should get into this merge cycle so that
others can work on top of them with no merge conflicts.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZPH+jA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKyACgldt6QeenTN+6dXIHS/eQHtTKZwMAn3arSeXI
QrUUnLFjOWyoX87tbMBQ
=LVw0
-----END PGP SIGNATURE-----
Merge tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
