We only request the control interface error IRQ if we set ctrlif_error,
as such we should only free it in that situation. Otherwise we will
attempt to free an IRQ we never requested and get a warning from the IRQ
core.
This patch moves the ctrlif_error variable into the arizona structure
and checks it in all cases we free the control interface error IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer versions of the IP have a lot of new interrupts and move several
existing interrupts. This patch adds the register definitions and regmap
hookup for these interrupts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Newer versions of the IP introduce short circuit protection which will
also shutdown the speaker. Rename the interrupt and associated register
bits associated with thermal events to better fit the function and avoid
conflict with future interrupt additions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
wm5110 has interrupts to signal that an output has fully enabled. This
patch adds in these interrupts although use is not made of them yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add register definitions for DA9063 AD (0x3) silicon variant ID
the ability to choose the silicon variant at run-time using regmap
configuration. This patch also adds RTC support for the AD silicon
changes.
It adds both BB and AD support as regmap ranges and then makes the
distinction between the two tables at run-time. This allows both AD
and BB silicon variants to be supported at the same time.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Extinguishes:
../drivers/mfd/max77686.c: In function ‘max77686_i2c_probe’:
../drivers/mfd/max77686.c:254:20:
warning: cast from pointer to integer of different size
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Maxim MAX77802 is a power management chip that contains 10 high
efficiency Buck regulators, 32 Low-dropout (LDO) regulators used
to power up application processors and peripherals, a 2-channel
32kHz clock outputs, a Real-Time-Clock (RTC) and a I2C interface
to program the individual regulators, clocks outputs and the RTC.
This patch adds support for MAX77802 to the MAX77686 driver and is
based on a driver added to the Chrome OS kernel 3.8 by Simon Glass.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
By using the generic IRQ support in the Register map API, it
is possible to get rid max77686-irq.c and simplify the code.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Extinguishes:
../drivers/mfd/tps65910.c: In function ‘tps65910_parse_dt’:
../drivers/mfd/tps65910.c:404:14:
warning: cast from pointer to integer of different size
Signed-off-by: Lee Jones <lee.jones@linaro.org>
If we receive EC interrupts after the cros_ec driver has probed, but
before the cros_ec_keyb driver has probed, the cros_ec IRQ handler
will not run the cros_ec_keyb notifier and the EC will leave the IRQ
line asserted. The cros_ec IRQ handler then returns IRQ_HANDLED and
the resulting flood of interrupts causes the machine to hang.
Since the EC interrupt is currently only used for the keyboard, move
the setup and handling of the EC interrupt to the cros_ec_keyb driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When communicating with the EC, the cmd_xfer() function should return the
number of bytes it received from the EC, or negative on error.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Just because the host was able to talk to the EC doesn't mean that the EC
was happy with what it was told. Errors in communincation are not the same
as error messages from the EC itself.
This change lets the EC report its errors separately.
[dianders: Added common function to cros_ec.c]
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the three wrapper functions that talk to the EC without passing all
the desired arguments and just use the underlying communication function
that passes everything in a struct intead.
This is internal code refactoring only. Nothing should change.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
struct cros_ec_device has a superfluous "name" field. We can get all the
debugging info we need from the existing ec_name and phys_name fields, so
let's take out the extra field.
The printout also has sufficient info in it without explicitly adding
the transport. Before this change:
cros-ec-spi spi2.0: Chrome EC (SPI)
After this change:
cros-ec-spi spi2.0: Chrome EC device registered
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is some internal structure reorganization / renaming to prepare
for future patches that will add a userspace API to cros_ec. There
should be no visible changes.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The members of struct cros_ec_device were improperly commented, and
intermixed the private and public sections. This is just cleanup to make it
more obvious what goes with what.
[dianders: left lock in the structure but gave it the name that will
eventually be used.]
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The lower-level driver may want to provide its own buffers. If so,
there's no need to allocate new ones. This already happens to work
just fine (since we check for size of 0 and use devm allocation), but
it's good to document it.
[dianders: Resolved conflicts; documented that no code changes needed
on mainline]
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This comment was incorrect, so update it.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for Samsung S2MPU02 PMIC device to the MFD sec-core driver.
The S2MPU02 device includes PMIC/RTC/Clock devices.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch convert mc13xxx MFD driver to use regmap irq framework
for interrupt registration.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The macro name for enable3 pin is named as AS3722_EXT_CONTROL_PIN_ENABLE2
which is conflict with the enable2 pin.
Correct this macro name to correctly reflect the enable pin i.e.
AS3722_EXT_CONTROL_PIN_ENABLE3.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reported-by: Dan Willemsen <dwillemsen@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are no Arizona devices with 3 core supplies but we define a fix
array with space for 3 core supplies. Lower the ARIZONA_MAX_CORE_SUPPLIES
define to 2, to save a few bytes.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rtsx driver using a single function for transfer data, dma map/unmap are
placed in one fix function. We need map/unmap dma in different place(for
mmc async driver), so add three function for dma map, dma transfer and
dma unmap.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is a set of 13 fixes, a MAINTAINERS update and a sparse update. The
fixes are mostly correct value initialisations, avoiding NULL derefs and some
uninitialised pointer avoidance.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTuNEhAAoJEDeqqVYsXL0MYC4H/2gpxHA9rELiqPRLJGNjt9v3
YlGrIwVAAdYLBSgwtkpAYj6oDJtwRmZvP3Saj2n5Lga+32mgFsPjvy+JsM3O41SL
k5QRlAs10wMbOB/dSoGxFsKdGnig4NolCIe5p0MGQvAbcCvh9z2Tr876ssvSfMCh
1mh0xmTCIutD7R2f5WjRckA+HZo+qmLLz5ZyogDasI3mSRAHjcZ+j5HdWBQbEsag
U6lPDR5VpUjGpigwJ+BPWwKTbIAIW1v2TB1YjWSHr5h2QPLBa+hfbyc15S1AjsGb
9F5/L432yk4UXQUKyKIpCKi8rDCoioM8dt8ofjjTNfNNjDlYRRHKutalef1yOw8=
=HPXQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
The fixes are mostly correct value initialisations, avoiding NULL
derefs and some uninitialised pointer avoidance.
All the patches have been incubated in -next for a few days. The
final patch (use the scsi data buffer length to extract transfer size)
has been rebased to add a cc to stable, but only the commit message
has changed"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] use the scsi data buffer length to extract transfer size
virtio-scsi: fix various bad behavior on aborted requests
virtio-scsi: avoid cancelling uninitialized work items
ibmvscsi: Add memory barriers for send / receive
ibmvscsi: Abort init sequence during error recovery
qla2xxx: Fix sparse warning in qla_target.c.
bnx2fc: Improve stats update mechanism
bnx2fc: do not scan uninitialized lists in case of error.
fc: ensure scan_work isn't active when freeing fc_rport
pm8001: Fix potential null pointer dereference and memory leak.
MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
be2iscsi: remove potential junk pointer free
be2iscsi: add an missing goto in error path
scsi_error: set DID_TIME_OUT correctly
scsi_error: fix invalid setting of host byte
This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zvT1
-----END PGP SIGNATURE-----
Merge tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This contains a few fixes for HD-audio: yet another Dell headset pin
quirk, a fixup for Thinkpad T540P, and an improved fix for
Haswell/Broadwell HDMI clock setup"
* tag 'sound-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N value as per CDCLK for HSW/BDW display HDA controller
drm/i915: provide interface for audio driver to query cdclk
ALSA: hda - Add a fixup for Thinkpad T540p
ALSA: hda - Add another headset pin quirk for some Dell machines
Pull btrfs fixes from Chris Mason:
"We've queued up a few fixes in my for-linus branch"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix crash when starting transaction
Btrfs: fix btrfs_print_leaf for skinny metadata
Btrfs: fix race of using total_bytes_pinned
btrfs: use E2BIG instead of EIO if compression does not help
btrfs: remove stale comment from btrfs_flush_all_pending_stuffs
Btrfs: fix use-after-free when cloning a trailing file hole
btrfs: fix null pointer dereference in btrfs_show_devname when name is null
btrfs: fix null pointer dereference in clone_fs_devices when name is null
btrfs: fix nossd and ssd_spread mount option regression
Btrfs: fix race between balance recovery and root deletion
Btrfs: atomically set inode->i_flags in btrfs_update_iflags
btrfs: only unlock block in verify_parent_transid if we locked it
Btrfs: assert send doesn't attempt to start transactions
btrfs compression: reuse recently used workspace
Btrfs: fix crash when mounting raid5 btrfs with missing disks
btrfs: create sprout should rename fsid on the sysfs as well
btrfs: dev replace should replace the sysfs entry
btrfs: dev add should add its sysfs entry
btrfs: dev delete should remove sysfs entry
btrfs: rename add_device_membership to btrfs_kobj_add_device
For Haswell and Broadwell, if the display power well has been disabled,
the display audio controller divider values EM4 M VALUE and EM5 N VALUE
will have been lost. The CDCLK frequency is required for reprogramming them
to generate 24MHz HD-A link BCLK. So provide a private interface for the
audio driver to query CDCLK.
This is a stopgap solution until a more generic interface between audio
and display drivers has been implemented.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here's a round of USB bugfixes, quirk additions, and new device ids for
3.16-rc4. Nothing major in here at all, just a bunch of tiny changes.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlO1+wwACgkQMUfUDdst+ylcuACfbIytKMfxNcmq2xG6AExXbVSl
IQAAnAvv4QjqzbtSVWaNZB/Kkxzh4xeN
=Igpa
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB bugfixes from Greg KH:
"Here's a round of USB bugfixes, quirk additions, and new device ids
for 3.16-rc4. Nothing major in here at all, just a bunch of tiny
changes. All have been in linux-next with no reported issues"
* tag 'usb-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: udc: delete td from req's td list at ep_dequeue
usb: Kconfig: make EHCI_MSM selectable for QCOM SOCs
usb-storage/SCSI: Add broken_fua blacklist flag
usb: musb: dsps: fix the base address for accessing the mode register
tools: ffs-test: fix header values endianess
usb: phy: msm: Do not do runtime pm if the phy is not idle
usb: musb: Ensure that cppi41 timer gets armed on premature DMA TX irq
usb: gadget: gr_udc: Fix check for invalid number of microframes
usb: musb: Fix panic upon musb_am335x module removal
usb: gadget: f_fs: resurect usb_functionfs_descs_head structure
Revert "tools: ffs-test: convert to new descriptor format fixing compilation error"
xhci: Fix runtime suspended xhci from blocking system suspend.
xhci: clear root port wake on bits if controller isn't wake-up capable
xhci: correct burst count field for isoc transfers on 1.0 xhci hosts
xhci: Use correct SLOT ID when handling a reset device command
MAINTAINERS: update e-mail address
usb: option: add/modify Olivetti Olicard modems
USB: ftdi_sio: fix null deref at port probe
MAINTAINERS: drop two usb-serial subdriver entries
USB: option: add device ID for SpeedUp SU9800 usb 3g modem
...
Well, one drivercore fix for kernfs to resolve a reported issue with
sysfs files being updated from atomic contexts, and another lz4 bugfix
for testing potential buffer overflows.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlO1/FEACgkQMUfUDdst+ynRPACfWcssJKICc2N7g9/0XXGVTjVT
PwwAnjQ8bjOfu6i2z/lViLtZGjOnzKor
=qtjB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Well, one drivercore fix for kernfs to resolve a reported issue with
sysfs files being updated from atomic contexts, and another lz4 bugfix
for testing potential buffer overflows"
* tag 'driver-core-3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
lz4: add overrun checks to lz4_uncompress_unknownoutputsize()
kernfs: kernfs_notify() must be useable from non-sleepable contexts
The 'sysret' fastpath does not correctly restore even all regular
registers, much less any segment registers or reflags values. That is
very much part of why it's faster than 'iret'.
Normally that isn't a problem, because the normal ptrace() interface
catches the process using the signal handler infrastructure, which
always returns with an iret.
However, some paths can get caught using ptrace_event() instead of the
signal path, and for those we need to make sure that we aren't going to
return to user space using 'sysret'. Otherwise the modifications that
may have been done to the register set by the tracer wouldn't
necessarily take effect.
Fix it by forcing IRET path by setting TIF_NOTIFY_RESUME from
arch_ptrace_stop_needed() which is invoked from ptrace_stop().
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8846bab180 introduced a helper that can be used to query the
wire transfer size for a SCSI command taking protection information into
account.
However, some commands do not have a 1:1 mapping between the block range
they work on and the payload size (discard, write same). After the
scatterlist has been set up these requests use __data_len to store the
number of bytes to report completion on. This means that callers of
scsi_transfer_length() would get the wrong byte count for these types of
requests.
To overcome this we make scsi_transfer_length() use the scatterlist
length in the scsi_data_buffer as basis for the wire transfer
calculation instead of __data_len.
Reported-by: Christoph Hellwig <hch@infradead.org>
Debugged-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Fixes: d77e65350f
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
d911d98748 ("kernfs: make kernfs_notify() trigger inotify events
too") added fsnotify triggering to kernfs_notify() which requires a
sleepable context. There are already existing users of
kernfs_notify() which invoke it from an atomic context and in general
it's silly to require a sleepable context for triggering a
notification.
The following is an invalid context bug triggerd by md invoking
sysfs_notify() from IO completion path.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:586
in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
2 locks held by swapper/1/0:
#0: (&(&vblk->vq_lock)->rlock){-.-...}, at: [<ffffffffa0039042>] virtblk_done+0x42/0xe0 [virtio_blk]
#1: (&(&bitmap->counts.lock)->rlock){-.....}, at: [<ffffffff81633718>] bitmap_endwrite+0x68/0x240
irq event stamp: 33518
hardirqs last enabled at (33515): [<ffffffff8102544f>] default_idle+0x1f/0x230
hardirqs last disabled at (33516): [<ffffffff818122ed>] common_interrupt+0x6d/0x72
softirqs last enabled at (33518): [<ffffffff810a1272>] _local_bh_enable+0x22/0x50
softirqs last disabled at (33517): [<ffffffff810a29e0>] irq_enter+0x60/0x80
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.16.0-0.rc2.git2.1.fc21.x86_64 #1
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
0000000000000000 f90db13964f4ee05 ffff88007d403b80 ffffffff81807b4c
0000000000000000 ffff88007d403ba8 ffffffff810d4f14 0000000000000000
0000000000441800 ffff880078fa1780 ffff88007d403c38 ffffffff8180caf2
Call Trace:
<IRQ> [<ffffffff81807b4c>] dump_stack+0x4d/0x66
[<ffffffff810d4f14>] __might_sleep+0x184/0x240
[<ffffffff8180caf2>] mutex_lock_nested+0x42/0x440
[<ffffffff812d76a0>] kernfs_notify+0x90/0x150
[<ffffffff8163377c>] bitmap_endwrite+0xcc/0x240
[<ffffffffa00de863>] close_write+0x93/0xb0 [raid1]
[<ffffffffa00df029>] r1_bio_write_done+0x29/0x50 [raid1]
[<ffffffffa00e0474>] raid1_end_write_request+0xe4/0x260 [raid1]
[<ffffffff813acb8b>] bio_endio+0x6b/0xa0
[<ffffffff813b46c4>] blk_update_request+0x94/0x420
[<ffffffff813bf0ea>] blk_mq_end_io+0x1a/0x70
[<ffffffffa00392c2>] virtblk_request_done+0x32/0x80 [virtio_blk]
[<ffffffff813c0648>] __blk_mq_complete_request+0x88/0x120
[<ffffffff813c070a>] blk_mq_complete_request+0x2a/0x30
[<ffffffffa0039066>] virtblk_done+0x66/0xe0 [virtio_blk]
[<ffffffffa002535a>] vring_interrupt+0x3a/0xa0 [virtio_ring]
[<ffffffff81116177>] handle_irq_event_percpu+0x77/0x340
[<ffffffff8111647d>] handle_irq_event+0x3d/0x60
[<ffffffff81119436>] handle_edge_irq+0x66/0x130
[<ffffffff8101c3e4>] handle_irq+0x84/0x150
[<ffffffff818146ad>] do_IRQ+0x4d/0xe0
[<ffffffff818122f2>] common_interrupt+0x72/0x72
<EOI> [<ffffffff8105f706>] ? native_safe_halt+0x6/0x10
[<ffffffff81025454>] default_idle+0x24/0x230
[<ffffffff81025f9f>] arch_cpu_idle+0xf/0x20
[<ffffffff810f5adc>] cpu_startup_entry+0x37c/0x7b0
[<ffffffff8104df1b>] start_secondary+0x25b/0x300
This patch fixes it by punting the notification delivery through a
work item. This ends up adding an extra pointer to kernfs_elem_attr
enlarging kernfs_node by a pointer, which is not ideal but not a very
big deal either. If this turns out to be an actual issue, we can move
kernfs_elem_attr->size to kernfs_node->iattr later.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Büsch <m@bues.ch>
Tested-by: Michael Büsch <m@bues.ch>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few more fixes for this RC cycle. There's a revert of a previous patch
which ended up being the wrong version, so we reverted that commit and
applied a better fix.
CPPI41 got a race condition fix which was found by Thomas Gleixner.
The MSM PHY driver got a runtime pm usage fix so that it wouldn't
kill the PHY while it was still being used.
We also have a fix for a panic caused when removing musb_am335x driver.
Other than that, a few other minor fixes.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Mt5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.16-rc4
A few more fixes for this RC cycle. There's a revert of a previous patch
which ended up being the wrong version, so we reverted that commit and
applied a better fix.
CPPI41 got a race condition fix which was found by Thomas Gleixner.
The MSM PHY driver got a runtime pm usage fix so that it wouldn't
kill the PHY while it was still being used.
We also have a fix for a panic caused when removing musb_am335x driver.
Other than that, a few other minor fixes.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Creating sprout will change the fsid of the mounted root.
do the same on the sysfs as well.
reproducer:
mount /dev/sdb /btrfs (seed disk)
btrfs dev add /dev/sdc /btrfs
mount -o rw,remount /btrfs
btrfs dev del /dev/sdb /btrfs
mount /dev/sdb /btrfs
Error:
kobject_add_internal failed for fe350492-dc28-4051-a601-e017b17e6145 with -EEXIST, don't try to register things with the same name in the same directory.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor fixes this time around. The highlights include:
- iscsi-target CHAP authentication fixes to enforce explicit key
values (Tejas Vaykole + rahul.rane)
- fix a long-standing OOPs in target-core when a alua configfs
attribute is accessed after port symlink has been removed.
(Sebastian Herbszt)
- fix a v3.10.y iscsi-target regression causing the login reject
status class/detail to be ignored (Christoph Vu-Brugier)
- fix a v3.10.y iscsi-target regression to avoid rejecting an
existing ITT during Data-Out when data-direction is wrong (Santosh
Kulkarni + Arshad Hussain)
- fix a iscsi-target related shutdown deadlock on UP kernels (Mikulas
Patocka)
- fix a v3.16-rc1 build issue with vhost-scsi + !CONFIG_NET (MST)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: fix iscsit_del_np deadlock on unload
iovec: move memcpy_from/toiovecend to lib/iovec.c
iscsi-target: Avoid rejecting incorrect ITT for Data-Out
tcm_loop: Fix memory leak in tcm_loop_submission_work error path
iscsi-target: Explicily clear login response PDU in exception path
target: Fix left-over se_lun->lun_sep pointer OOPs
iscsi-target; Enforce 1024 byte maximum for CHAP_C key value
iscsi-target: Convert chap_server_compute_md5 to use kstrtoul
Here includes a few patchset for fixing mostly HD-audio issues in
addition to a patch assuring the compress API bytes alignment and a
fix for the die-hard existing race condition at USB-audio
disconnection. The volume looks big in Realtek HD-audio code, but
it's just a translation of the fixup tables, and the actual changes
are rather trivial.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=iKT+
-----END PGP SIGNATURE-----
Merge tag 'sound-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here includes a few patchset for fixing mostly HD-audio issues in
addition to a patch assuring the compress API bytes alignment and a
fix for the die-hard existing race condition at USB-audio
disconnection. The volume looks big in Realtek HD-audio code, but
it's just a translation of the fixup tables, and the actual changes
are rather trivial"
* tag 'sound-3.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - restore BCLK M/N values when resuming HSW/BDW display controller
ALSA: usb-audio: Fix races at disconnection and PCM closing
ALSA: hda - Adjust speaker HPF and add LED support for HP Spectre 13
ALSA: hda - Make the pin quirk tables use the SND_HDA_PIN_QUIRK macro
ALSA: hda - Make a SND_HDA_PIN_QUIRK macro
ALSA: hda - Add pin quirk for Dell XPS 15
ALSA: hda - hdmi: call overridden init on resume
ALSA: hda - Fix usage of "model" module parameter
ALSA: compress: fix the struct alignment to 4 bytes
Pull drm fixes from Dave Airlie:
"Exynos, i915 and msm fixes and one core fix.
exynos:
hdmi power off and mixer issues
msm:
iommu, build fixes,
i915:
regression races and warning fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
drm/i915: vlv_prepare_pll is only needed in case of non DSI interfaces
drm: fix NULL pointer access by wrong ioctl
drm/exynos: enable vsync interrupt while waiting for vblank
drm/exynos: soft reset mixer before reconfigure after power-on
drm/exynos: allow multiple layer updates per vsync for mixer
drm/i915: Hold the table lock whilst walking the file's idr and counting the objects in debugfs
drm/i915: BDW: Adding Reserved PCI IDs.
drm/i915: Only mark the ctx as initialised after a SET_CONTEXT operation
drm/exynos: stop mixer before gating clocks during poweroff
drm/exynos: set power state variable after enabling clocks and power
drm/exynos: disable unused windows on apply
drm/exynos: Fix de-registration ordering
drm/exynos: change zero to NULL for sparse
drm/exynos: dpi: Fix NULL pointer dereference with legacy bindings
drm/exynos: hdmi: fix power order issue
drm/i915: default to having backlight if VBT not available
drm/i915: cache hw power well enabled state
drm/msm: fix IOMMU cleanup for -EPROBE_DEFER
drm/msm: use PAGE_ALIGNED instead of IS_ALIGNED(PAGE_SIZE)
drm/msm/hdmi: set hdp clock rate before prepare_enable
...
ERROR: "memcpy_fromiovecend" [drivers/vhost/vhost_scsi.ko] undefined!
commit 9f977ef7b6
vhost-scsi: Include prot_bytes into expected data transfer length
in target-pending makes drivers/vhost/scsi.c call memcpy_fromiovecend().
This function is not available when CONFIG_NET is not enabled.
socket.h already includes uio.h, so no callers need updating.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Even though usb_functionfs_descs_head structure is now deprecated,
it has been used by some user space tools. Its removel in commit
[ac8dde1: “Add flags to descriptors block”] was an oversight
leading to build breakage for such tools.
Bring it back so that old user space tools can still be build
without problems on newer kernel versions.
Cc: <stable@vger.kernel.org> # 3.14
Reported-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reported-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull block fixes from Jens Axboe:
"A small collection of fixes/changes for the current series. This
contains:
- Removal of dead code from Gu Zheng.
- Revert of two bad fixes that went in earlier in this round, marking
things as __init that were not purely used from init.
- A fix for blk_mq_start_hw_queue() using the __blk_mq_run_hw_queue(),
which could place us wrongly. Make it use the non __ variant,
which handles cases where we are called from the wrong CPU set.
From me.
- A fix for drbd, which allocates discard requests without room for
the SCSI payload. From Lars Ellenberg.
- A fix for user-after-free in the blkcg code from Tejun.
- Addition of limiting gaps in SG lists, if the hardware needs it.
This is the last pre-req patch for blk-mq to enable the full NVMe
conversion. Could wait until 3.17, but it's simple enough so would
be nice to have everything we need for the NVMe port in the 3.17
release. From me"
* 'for-linus' of git://git.kernel.dk/linux-block:
drbd: fix NULL pointer deref in blk_add_request_payload
blk-mq: blk_mq_start_hw_queue() should use blk_mq_run_hw_queue()
block: add support for limiting gaps in SG lists
bio: remove unused macro bip_vec_idx()
Revert "block: add __init to elv_register"
Revert "block: add __init to blkcg_policy_register"
blkcg: fix use-after-free in __blkg_release_rcu() by making blkcg_gq refcnt an atomic_t
floppy: format block0 read error message properly
blkdev_read_iter() wants to cap the iov_iter by the amount of data
remaining to the end of device. That's what iov_iter_truncate() is for
(trim iter->count if it's above the given limit). So far, so good, but
the argument of iov_iter_truncate() is size_t, so on 32bit boxen (in
case of a large device) we end up with that upper limit truncated down
to 32 bits *before* comparing it with iter->count.
Easily fixed by making iov_iter_truncate() take 64bit argument - it does
the right thing after such change (we only reach the assignment in there
when the current value of iter->count is greater than the limit, i.e.
for anything that would get truncated we don't reach the assignment at
all) and that argument is not the new value of iter->count - it's an
upper limit for such.
The overhead of passing u64 is not an issue - the thing is inlined, so
callers passing size_t won't pay any penalty.
Reported-and-tested-by: Theodore Tso <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Tested-by: Bruno Wolff III <bruno@wolff.to>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Fix crash in ipvs tot_stats estimator, from Julian Anastasov.
2) Fix OOPS in nf_nat on netns removal, from Florian Westphal.
3) Really really really fix locking issues in slip and slcan tty write
wakeups, from Tyler Hall.
4) Fix checksum offloading in fec driver, from Fugang Duan.
5) Off by one in BPF instruction limit test, from Kees Cook.
6) Need to clear all TSO capability flags when doing software TSO in
tg3 driver, from Prashant Sreedharan.
7) Fix memory leak in vlan_reorder_header() error path, from Li
RongQing.
8) Fix various bugs in xen-netfront and xen-netback multiqueue support,
from David Vrabel and Wei Liu.
9) Fix deadlock in cxgb4 driver, from Li RongQing.
10) Prevent double free of no-cache DST entries, from Eric Dumazet.
11) Bad csum_start handling in skb_segment() leads to crashes when
forwarding, from Tom Herbert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: fix setting csum_start in skb_segment()
ipv4: fix dst race in sk_dst_get()
net: filter: Use kcalloc/kmalloc_array to allocate arrays
trivial: net: filter: Change kerneldoc parameter order
trivial: net: filter: Fix typo in comment
net: allwinner: emac: Add missing free_irq
cxgb4: use dev_port to identify ports
xen-netback: bookkeep number of active queues in our own module
tg3: Change nvram command timeout value to 50ms
cxgb4: Not need to hold the adap_rcu_lock lock when read adap_rcu_list
be2net: fix qnq mode detection on VFs
of: mdio: fixup of_phy_register_fixed_link parsing of new bindings
at86rf230: fix irq setup
net: phy: at803x: fix coccinelle warnings
net/mlx4_core: Fix the error flow when probing with invalid VF configuration
tulip: Poll link status more frequently for Comet chips
net: huawei_cdc_ncm: increase command buffer size
drivers: net: cpsw: fix dual EMAC stall when connected to same switch
xen-netfront: recreate queues correctly when reconnecting
xen-netfront: fix oops when disconnected from backend
...
When IP route cache had been removed in linux-3.6, we broke assumption
that dst entries were all freed after rcu grace period. DST_NOCACHE
dst were supposed to be freed from dst_release(). But it appears
we want to keep such dst around, either in UDP sockets or tunnels.
In sk_dst_get() we need to make sure dst refcount is not 0
before incrementing it, or else we might end up freeing a dst
twice.
DST_NOCACHE set on a dst does not mean this dst can not be attached
to a socket or a tunnel.
Then, before actual freeing, we need to observe a rcu grace period
to make sure all other cpus can catch the fact the dst is no longer
usable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dormando <dormando@rydia.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new set of bug fixes for 3.16, containing patches for seven platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fJMs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A new set of bug fixes for 3.16, containing patches for seven
platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
ARM: integrator: fix OF-related regression
ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
ARM: dts: kirkwood: fix phy-connection-type for Guruplug
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
ARM: dts: imx51-babbage: Fix esdhc setup
ARM: dts: mx5: Move the display out of soc {} node
ARM: dts: mx5: Fix IPU port node placement
ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
ARM: mvebu: Fix broken SoC ID detection
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
ARM: multi_v7_defconfig: Add QCOM GSBI driver
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
tty: serial: msm: Fix section mismatch warning
...
race condition that happens between enabling/disabling syscall tracepoints
and new process creations (the check to go into the ptrace path for a process
can be set when it shouldn't, or not set when it should). Not a major bug
but one that should be fixed and even applied to stable.
The other two patches are cleanup/fixes that are not that critical, but
for an -rc1 release would be nice to have. They both deal with syscall
tracepoints.
It also includes a patch to introduce a new macro for the TRACE_EVENT()
format called __field_struct(). Originally, __field() was used to record
any variable into a trace event, but with the addition of setting the
"is signed" attribute, the check causes anything but a primitive variable
to fail to compile. That is, structs and unions can't be used as they
once were. When the "is signed" check was introduce there were only
primitive variables being recorded. But that will change soon and it
was reported that __field() causes build failures.
To solve the __field() issue, __field_struct() is introduced to allow
trace_events to be able to record complex types too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTpxx+AAoJEKQekfcNnQGu8dQH/RWwKuq/SDqdqFrYM3y0MGtU
GpWTzaTYfhoO7FE2zNx3JQtfu5Zg+KPzavecEQqYJGdUvd5lopo+GR4TYQ2GIDdA
O4gBgXkxJjYCQ4x9INXf/U8Afd4tfCYSWik2zzWUZaJSLd6pMV/4XbqqZItZ7aqt
bxWa7CgmSMHmfsO5a3xWzX0ybPCmYw/+G15CZDGguoazO1FU6oFAnKnr86PGhquH
eIHzGAO7ka6k+hQwM1gzUi5vIN+OGBZ4HuJCFu/jqaJHMxW0lomL93Gruifk3l4v
r2ierd0FjMSrV1BzCWRR+diWq8W0xwOUutFd1eG3fKlKHZJn4oZfiUHsZw65PFQ=
=Idsk
-----END PGP SIGNATURE-----
Merge tag 'trace-fixes-v3.16-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing cleanups and fixes from Steven Rostedt:
"This includes three patches from Oleg Nesterov. The first is a fix to
a race condition that happens between enabling/disabling syscall
tracepoints and new process creations (the check to go into the ptrace
path for a process can be set when it shouldn't, or not set when it
should). Not a major bug but one that should be fixed and even
applied to stable.
The other two patches are cleanup/fixes that are not that critical,
but for an -rc1 release would be nice to have. They both deal with
syscall tracepoints.
It also includes a patch to introduce a new macro for the
TRACE_EVENT() format called __field_struct(). Originally, __field()
was used to record any variable into a trace event, but with the
addition of setting the "is signed" attribute, the check causes
anything but a primitive variable to fail to compile. That is,
structs and unions can't be used as they once were. When the "is
signed" check was introduce there were only primitive variables being
recorded. But that will change soon and it was reported that
__field() causes build failures.
To solve the __field() issue, __field_struct() is introduced to allow
trace_events to be able to record complex types too"
* tag 'trace-fixes-v3.16-rc1-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add __field_struct macro for TRACE_EVENT()
tracing: syscall_regfunc() should not skip kernel threads
tracing: Change syscall_*regfunc() to check PF_KTHREAD and use for_each_process_thread()
tracing: Fix syscall_*regfunc() vs copy_process() race
Another restriction inherited for NVMe - those devices don't support
SG lists that have "gaps" in them. Gaps refers to cases where the
previous SG entry doesn't end on a page boundary. For NVMe, all SG
entries must start at offset 0 (except the first) and end on a page
boundary (except the last).
Signed-off-by: Jens Axboe <axboe@fb.com>
