Internal address mode (3- or 4-byte) affects to the address length in
Read Any Reg op. Read Any Reg op is used in SMPT parse and other setup
functions. Current driver assumes that address mode is factory default
but users can change it via volatile and non-volatile registers.
Current address mode can be checked by CFR2V[7] but Read Any Reg op is
needed to read CFR2V (chicken-and-egg).
Introduce a way to determine current address mode by comparing status
register 1 values read by different address length.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Link: https://lore.kernel.org/r/20230331074606.3559258-11-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Make the method public, as it will be used as a last resort to enable
4byte address mode when we can't determine the address mode at runtime.
Update the addr_nbytes and current address mode while exiting the 4byte
address mode too, as it may be used in the future by manufacturer
drivers. No functional change. spi_nor_restore didn't update the address
mode nbytes, but updating them now doesn't harm as the method is called
in the driver's remove and shutdown paths.
Link: https://lore.kernel.org/r/20230331074606.3559258-10-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
The bug was obswerved while reading code. There are not many users of
addr_mode_nbytes. Anyway, we should update the flash's current address
mode when changing the address mode, fix it. We don't care for now about
the set_4byte_addr_mode(nor, false) from spi_nor_restore(), as it is
used at driver remove and shutdown.
Fixes: d7931a2150 ("mtd: spi-nor: core: Track flash's internal address mode")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230331074606.3559258-9-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Some SPI NOR controllers that used this method were moved to
drivers/spi/. We don't accept new support for the existing SPI NOR
controllers drivers under drivers/mtd/spi-nor/controllers/ and we
encourage their owners to move the drivers under drivers/spi/.
Make spi_nor_restore() private as we're going to use it just in core.c.
Link: https://lore.kernel.org/r/20230331074606.3559258-8-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
JESD216 SFDP defines in BFPT methods to enter and exit the
4-Byte Address Mode. The flash parameters and settings that are
retrieved from SFDP have higher precedence than the static
initialized ones, because they should be more accurate and less
error prone than those initialized statically. Parse and favor the
BFPT-parsed set_4byte_addr_mode methods.
Some regressions may be introduced by this patch, because the
params->set_4byte_addr_mode method that was set either in
spi_nor_init_default_params() or later overwritten in default_init()
hooks, are now be overwritten with a different value based on the
BFPT data. If that's the case, the fix is to introduce a post_bfpt
fixup hook where one should fix the wrong BFPT info.
Link: https://lore.kernel.org/r/20230331074606.3559258-7-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
This method can be retrieved at BFPT parsing time. The method is
described in JESD216 BFPT[SFDP_DWORD(16)], BIT(28) and BIT(20).
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230331074606.3559258-6-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Rename method to spi_nor_set_4byte_addr_mode_en4b_ex4b and extend its
description. This method is described in JESD216 BFPT[SFDP_DWORD(16)],
BIT(31) and BIT(23).
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230331074606.3559258-5-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Rename method to spi_nor_set_4byte_addr_mode_brwr and extend its
description. This method is described in JESD216 BFPT[SFDP_DWORD(16)],
BIT(28) and BIT(20).
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230331074606.3559258-4-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Rename method to spi_nor_set_4byte_addr_mode_wren_en4b_ex4b and extend
its description. This method is described in JESD216 BFPT[SFDP_DWORD(16)],
BIT(30) and BIT(22).
Reviewed-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20230331074606.3559258-3-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Describe this new part and provide the RWW flag for it.
There is no public datasheet, but here are the sfdp tables plus base
testing to show it works.
$ cat /sys/bus/spi/devices/spi0.0/spi-nor/partname
mx25uw51245g
$ cat /sys/bus/spi/devices/spi0.0/spi-nor/jedec_id
c2813a
$ cat /sys/bus/spi/devices/spi0.0/spi-nor/manufacturer
macronix
$ xxd -p /sys/bus/spi/devices/spi0.0/spi-nor/sfdp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$ md5sum /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
047a884cf44d9ffc2a94d3ab37b48c63 /sys/bus/spi/devices/spi0.0/spi-nor/sfdp
$ dd if=/dev/urandom of=./qspi_test bs=1M count=6
6+0 records in
6+0 records out
$ mtd_debug write /dev/mtd1 0 6291456 qspi_test
Copied 6291456 bytes from qspi_test to address 0x00000000 in flash
$ mtd_debug erase /dev/mtd1 0 6291456
Erased 6291456 bytes from address 0x00000000 in flash
$ mtd_debug read /dev/mtd1 0 6291456 qspi_read
Copied 6291456 bytes from address 0x00000000 in flash to qspi_read
$ hexdump qspi_read
0000000 ffff ffff ffff ffff ffff ffff ffff ffff
*
0600000
$ mtd_debug write /dev/mtd1 0 6291456 qspi_test
Copied 6291456 bytes from qspi_test to address 0x00000000 in flash
$ mtd_debug read /dev/mtd1 0 6291456 qspi_read
Copied 6291456 bytes from address 0x00000000 in flash to qspi_read
$ sha1sum qspi_test qspi_read
d24a9523db829a0df688f34b8dc76a1383b74024 qspi_test
d24a9523db829a0df688f34b8dc76a1383b74024 qspi_read
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230331194620.839899-2-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Bank size is derived from the chip's size, which in
spi_nor_init_default_params() can still be zero if the flash size is
not specified at flash declaration. Let the flash size be updated
by parsing SFDP and do the initialization of the bank size in
spi_nor_late_init_params(). Flashes that don't define the SFDP tables
must specify the flash size at declaration.
Fixes: 9d6c5d64f0 ("mtd: spi-nor: Introduce the concept of bank")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230331194620.839899-1-miquel.raynal@bootlin.com
[ta: drop superfluous initialization in spi_nor_init_default_params(),
reword commit message, add Fixes tag.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Use the new TLV APIs for existing slow path commands. The TLV
APIs will be used to populate extended headers for some of the
Firmware commands, which will be introduced in the patches that
follow.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1680169540-10029-7-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reducing the number of arguments to bnxt_qplib_rcfw_send_message
by enclosing all its arguments into a command message structure.
Use the same struct while passing the command information to
send_message.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1680169540-10029-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Updating the HW structures to the latest version.
This is copied from the code maintained internally. No functionality
changes in this patch. Code is re-organized to match the file maintained
in the internal tree. Also, New HW interface structures are added, which
will be used by the drivers in future.
CC: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://lore.kernel.org/r/1680169540-10029-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Íñigo Huguet says:
====================
sfc: support unicast PTP
Unicast PTP was not working with sfc NICs.
The reason was that these NICs don't timestamp all incoming packets,
but instead they only timestamp packets of the queues that are selected
for that. Currently, only one RX queue is configured for timestamp: the
RX queue of the PTP channel. The packets that are put in the PTP RX
queue are selected according to firmware filters configured from the
driver.
Multicast PTP was already working because the needed filters are known
in advance, so they're inserted when PTP is enabled. This patches
add the ability to dynamically add filters for unicast addresses,
extracted from the TX PTP-event packets.
Since we don't know in advance how many filters we'll need, some info
about the filters need to be saved. This will allow to check if a filter
already exists or if a filter is too old and should be removed.
Note that the previous point is unnecessary for multicast filters, but
I've opted to change how they're handled to match the new unicast's
filters to avoid having duplicate insert/remove_filters functions,
once for each type of filter.
Tested: With ptp4l, all combinations of IPv4/IPv6, master/slave and
unicast/multicast
Reported-by: Yalin Li <yalli@redhat.com>
====================
Link: https://lore.kernel.org/r/20230331111404.17256-1-ihuguet@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Filters inserted to support unicast PTP mode might become unused after
some time, so we need to remove them to avoid accumulating many of them.
Refresh the expiration time of a filter each time it's used. Then check
periodically if any filter hasn't been used for a long time (30s) and
remove it.
Reported-by: Yalin Li <yalli@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When sending a PTP event packet, add the correct filters that will make
that future incoming unicast PTP event packets will be timestamped.
The unicast address for the filter is gotten from the outgoing skb
before sending it.
Until now they were not timestamped because only filters that match with
the PTP multicast addressed were being configured into the NIC for the
PTP special channel. Packets received through different channels are not
timestamped, getting "received SYNC without timestamp" error in ptp4l.
Note that the inserted filters are never removed unless the NIC is stopped
or reconfigured, so efx_ptp_stop is called. Removal of old filters will
be handled by the next patch.
Additionally, cleanup a bit efx_ptp_xmit_skb_mc to use the reverse xmas
tree convention and remove an unnecessary assignment to rc variable in
void function.
Reported-by: Yalin Li <yalli@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a second list for unicast filters and generalize the
efx_ptp_insert/remove_filters functions to allow acting in any of the 2
lists.
No filters for unicast are inserted yet. That will be done in the next
patch.
The reason to use 2 different lists instead of a single one is that, in
next patches, we will want to check if unicast filters are already added
and if they're expired. We don't need that for multicast filters.
Reported-by: Yalin Li <yalli@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of using a fixed sized array for the PTP filters, use a list.
This is not actually necessary at this point because the filters for
multicast PTP are a fixed number, but this is a preparation for the
following patches adding support for unicast PTP.
To avoid confusion with the new struct type efx_ptp_rxfilter, change the
name of some local variables from rxfilter to spec, given they're of the
type efx_filter_spec.
Reported-by: Yalin Li <yalli@redhat.com>
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After a pci_doe_task completes, its work_struct needs to be destroyed
to avoid a memory leak with CONFIG_DEBUG_OBJECTS=y.
Fixes: 9d24322e88 ("PCI/DOE: Add DOE mailbox support functions")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: stable@vger.kernel.org # v6.0+
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/775768b4912531c3b887d405fc51a50e465e1bf9.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Gregory Price reports a WARN splat with CONFIG_DEBUG_OBJECTS=y upon CXL
probing because pci_doe_submit_task() invokes INIT_WORK() instead of
INIT_WORK_ONSTACK() for a work_struct that was allocated on the stack.
All callers of pci_doe_submit_task() allocate the work_struct on the
stack, so replace INIT_WORK() with INIT_WORK_ONSTACK() as a backportable
short-term fix.
The long-term fix implemented by a subsequent commit is to move to a
synchronous API which allocates the work_struct internally in the DOE
library.
Stacktrace for posterity:
WARNING: CPU: 0 PID: 23 at lib/debugobjects.c:545 __debug_object_init.cold+0x18/0x183
CPU: 0 PID: 23 Comm: kworker/u2:1 Not tainted 6.1.0-0.rc1.20221019gitaae703b02f92.17.fc38.x86_64 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Call Trace:
pci_doe_submit_task+0x5d/0xd0
pci_doe_discovery+0xb4/0x100
pcim_doe_create_mb+0x219/0x290
cxl_pci_probe+0x192/0x430
local_pci_probe+0x41/0x80
pci_device_probe+0xb3/0x220
really_probe+0xde/0x380
__driver_probe_device+0x78/0x170
driver_probe_device+0x1f/0x90
__driver_attach_async_helper+0x5c/0xe0
async_run_entry_fn+0x30/0x130
process_one_work+0x294/0x5b0
Fixes: 9d24322e88 ("PCI/DOE: Add DOE mailbox support functions")
Link: https://lore.kernel.org/linux-cxl/Y1bOniJliOFszvIK@memverge.com/
Reported-by: Gregory Price <gregory.price@memverge.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Tested-by: Gregory Price <gregory.price@memverge.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Gregory Price <gregory.price@memverge.com>
Cc: stable@vger.kernel.org # v6.0+
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/67a9117f463ecdb38a2dbca6a20391ce2f1e7a06.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If the length in the CDAT header is larger than the concatenation of the
header and all table entries, then the CDAT exposed to user space
contains trailing null bytes.
Not every consumer may be able to handle that. Per Postel's robustness
principle, "be liberal in what you accept" and silently reduce the
cached length to avoid exposing those null bytes.
Fixes: c97006046c ("cxl/port: Read CDAT table")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: stable@vger.kernel.org # v6.0+
Link: https://lore.kernel.org/r/6d98b3c7da5343172bd3ccabfabbc1f31c079d74.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If truncated CDAT entries are received from a device, the concatenation
of those entries constitutes a corrupt CDAT, yet is happily exposed to
user space.
Avoid by verifying response lengths and erroring out if truncation is
detected.
The last CDAT entry may still be truncated despite the checks introduced
herein if the length in the CDAT header is too small. However, that is
easily detectable by user space because it reaches EOF prematurely.
A subsequent commit which rightsizes the CDAT response allocation closes
that remaining loophole.
The two lines introduced here which exceed 80 chars are shortened to
less than 80 chars by a subsequent commit which migrates to a
synchronous DOE API and replaces "t.task.rv" by "rc".
The existing acpi_cdat_header and acpi_table_cdat struct definitions
provided by ACPICA cannot be used because they do not employ __le16 or
__le32 types. I believe that cannot be changed because those types are
Linux-specific and ACPI is specified for little endian platforms only,
hence doesn't care about endianness. So duplicate the structs.
Fixes: c97006046c ("cxl/port: Read CDAT table")
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: stable@vger.kernel.org # v6.0+
Link: https://lore.kernel.org/r/bce3aebc0e8e18a1173425a7a865b232c3912963.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
cxl_cdat_get_length() only checks whether the DOE response size is
sufficient for the Table Access response header (1 dword), but not the
succeeding CDAT header (1 dword length plus other fields).
It thus returns whatever uninitialized memory happens to be on the stack
if a truncated DOE response with only 1 dword was received. Fix it.
Fixes: c97006046c ("cxl/port: Read CDAT table")
Reported-by: Ming Li <ming4.li@intel.com>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Ming Li <ming4.li@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: stable@vger.kernel.org # v6.0+
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: https://lore.kernel.org/r/000e69cd163461c8b1bc2cf4155b6e25402c29c7.1678543498.git.lukas@wunner.de
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Replace the hardcoded final numbers in the AUX SYNC/precharge
setup, and derive those from numbers from the (e)DP specs.
The new functions can serve as the single point of truth for
the number of SYNC pulses we use.
Cc: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230329172434.18744-2-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Fast wake should use 8 SYNC pulses for the preamble
and 10-16 SYNC pulses for the precharge. Reduce our
fast wake SYNC count to match the maximum value.
We also use the maximum precharge length for normal
AUX transactions.
Cc: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230329172434.18744-1-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
bpf_obj_drop_impl has a void return type. In check_kfunc_call, the "else
if" which sets insn_aux->kptr_struct_meta for bpf_obj_drop_impl is
surrounded by a larger if statement which checks btf_type_is_ptr. As a
result:
* The bpf_obj_drop_impl-specific code will never execute
* The btf_struct_meta input to bpf_obj_drop is always NULL
* __bpf_obj_drop_impl will always see a NULL btf_record when called
from BPF program, and won't call bpf_obj_free_fields
* program-allocated kptrs which have fields that should be cleaned up
by bpf_obj_free_fields may instead leak resources
This patch adds a btf_type_is_void branch to the larger if and moves
special handling for bpf_obj_drop_impl there, fixing the issue.
Fixes: ac9f06050a ("bpf: Introduce bpf_obj_drop")
Cc: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Link: https://lore.kernel.org/r/20230403200027.2271029-1-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Smatch reports:
drivers/soc/bcm/brcmstb/biuctrl.c:291 setup_hifcpubiuctrl_regs() warn:
'cpubiuctrl_base' from of_iomap() not released on lines: 291.
This is because in setup_hifcpubiuctrl_regs(),
cpubiuctrl_base is not released when handle error, which may cause a leak.
To fix this, iounmap is added when handle error.
Fixes: 22f7a9116e ("soc: brcmstb: Correct CPU_CREDIT_REG offset for Brahma-B53 CPUs")
Signed-off-by: Zhaoyang Li <lizhaoyang04@hust.edu.cn>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230327115422.1536615-1-lizhaoyang04@hust.edu.cn
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-25-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-24-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-23-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-22-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-19-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-18-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230403154014.2564054-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver core allows for struct class to be in read-only
memory, move the tty_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/2023040250-landowner-unfitted-11f4@gregkh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
