Commit graph

1,185,212 commits

Author SHA1 Message Date
Nathan Lynch
5d08633e5f powerpc/pseries/lparcfg: add missing RTAS retry status handling
The ibm,get-system-parameter RTAS function may return -2 or 990x,
which indicate that the caller should try again.

lparcfg's parse_system_parameter_string() ignores this, making it
possible to intermittently report incorrect SPLPAR characteristics.

Move the RTAS call into a coventional rtas_busy_delay()-based loop.

Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230125-b4-powerpc-rtas-queue-v3-4-26929c8cce78@linux.ibm.com
2023-02-13 22:35:01 +11:00
Nathan Lynch
daa8ab5904 powerpc/pseries/lpar: add missing RTAS retry status handling
The ibm,get-system-parameter RTAS function may return -2 or 990x,
which indicate that the caller should try again.

pseries_lpar_read_hblkrm_characteristics() ignores this, making it
possible to incorrectly detect TLB block invalidation characteristics
at boot.

Move the RTAS call into a coventional rtas_busy_delay()-based loop.

Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Fixes: 1211ee61b4 ("powerpc/pseries: Read TLB Block Invalidate Characteristics")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230125-b4-powerpc-rtas-queue-v3-3-26929c8cce78@linux.ibm.com
2023-02-13 22:35:01 +11:00
Nathan Lynch
cc4b26eab1 powerpc/perf/hv-24x7: add missing RTAS retry status handling
The ibm,get-system-parameter RTAS function may return -2 or 990x,
which indicate that the caller should try again. read_24x7_sys_info()
ignores this, allowing transient failures in reporting processor
module information.

Move the RTAS call into a coventional rtas_busy_delay()-based loop,
along with the parsing of results on success.

Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Fixes: 8ba2142673 ("powerpc/hv-24x7: Add rtas call in hv-24x7 driver to get processor details")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230125-b4-powerpc-rtas-queue-v3-2-26929c8cce78@linux.ibm.com
2023-02-13 22:35:01 +11:00
Nathan Lynch
09d1ea72c8 powerpc/rtas: handle extended delays safely in early boot
Some code that runs early in boot calls RTAS functions that can return
-2 or 990x statuses, which mean the caller should retry. An example is
pSeries_cmo_feature_init(), which invokes ibm,get-system-parameter but
treats these benign statuses as errors instead of retrying.

pSeries_cmo_feature_init() and similar code should be made to retry
until they succeed or receive a real error, using the usual pattern:

	do {
		rc = rtas_call(token, etc...);
	} while (rtas_busy_delay(rc));

But rtas_busy_delay() will perform a timed sleep on any 990x
status. This isn't safe so early in boot, before the CPU scheduler and
timer subsystem have initialized.

The -2 RTAS status is much more likely to occur during single-threaded
boot than 990x in practice, at least on PowerVM. This is because -2
usually means that RTAS made progress but exhausted its self-imposed
timeslice, while 990x is associated with concurrent requests from the
OS causing internal contention. Regardless, according to the language
in PAPR, the OS should be prepared to handle either type of status at
any time.

Add a fallback path to rtas_busy_delay() to handle this as safely as
possible, performing a small delay on 990x. Include a counter to
detect retry loops that aren't making progress and bail out. Add __ref
to rtas_busy_delay() since it now conditionally calls an __init
function.

This was found by inspection and I'm not aware of any real
failures. However, the implementation of rtas_busy_delay() before
commit 38f7b7067d ("powerpc/rtas: rtas_busy_delay() improvements")
was not susceptible to this problem, so let's treat this as a
regression.

Signed-off-by: Nathan Lynch <nathanl@linux.ibm.com>
Fixes: 38f7b7067d ("powerpc/rtas: rtas_busy_delay() improvements")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230125-b4-powerpc-rtas-queue-v3-1-26929c8cce78@linux.ibm.com
2023-02-13 22:35:01 +11:00
Russell Currey
4b3e71e9a3 integrity/powerpc: Support loading keys from PLPKS
Add support for loading keys from the PLPKS on pseries machines, with the
"ibm,plpks-sb-v1" format.

The object format is expected to be the same, so there shouldn't be any
functional differences between objects retrieved on powernv or pseries.

Unlike on powernv, on pseries the format string isn't contained in the
device tree. Use secvar_ops->format() to fetch the format string in a
generic manner, rather than searching the device tree ourselves.

(The current code searches the device tree for a node compatible with
"ibm,edk2-compat-v1". This patch switches to calling secvar_ops->format(),
which in the case of OPAL/powernv means opal_secvar_format(), which
searches the device tree for a node compatible with "ibm,secvar-backend"
and checks its "format" property. These are equivalent, as skiboot creates
a node with both "ibm,edk2-compat-v1" and "ibm,secvar-backend" as
compatible strings.)

Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230210080401.345462-27-ajd@linux.ibm.com
2023-02-13 22:34:44 +11:00
Russell Currey
3c8069b0c3 integrity/powerpc: Improve error handling & reporting when loading certs
A few improvements to load_powerpc.c:

 - include integrity.h for the pr_fmt()
 - move all error reporting out of get_cert_list()
 - use ERR_PTR() to better preserve error detail
 - don't use pr_err() for missing keys

Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230210080401.345462-26-ajd@linux.ibm.com
2023-02-13 22:34:44 +11:00
Russell Currey
ccadf154cb powerpc/pseries: Implement secvars for dynamic secure boot
The pseries platform can support dynamic secure boot (i.e. secure boot
using user-defined keys) using variables contained with the PowerVM LPAR
Platform KeyStore (PLPKS).  Using the powerpc secvar API, expose the
relevant variables for pseries dynamic secure boot through the existing
secvar filesystem layout.

The relevant variables for dynamic secure boot are signed in the
keystore, and can only be modified using the H_PKS_SIGNED_UPDATE hcall.
Object labels in the keystore are encoded using ucs2 format.  With our
fixed variable names we don't have to care about encoding outside of the
necessary byte padding.

When a user writes to a variable, the first 8 bytes of data must contain
the signed update flags as defined by the hypervisor.

When a user reads a variable, the first 4 bytes of data contain the
policies defined for the object.

Limitations exist due to the underlying implementation of sysfs binary
attributes, as is the case for the OPAL secvar implementation -
partial writes are unsupported and writes cannot be larger than PAGE_SIZE.
(Even when using bin_attributes, which can be larger than a single page,
sysfs only gives us one page's worth of write buffer at a time, and the
hypervisor does not expose an interface for partial writes.)

Co-developed-by: Nayna Jain <nayna@linux.ibm.com>
Signed-off-by: Nayna Jain <nayna@linux.ibm.com>
Co-developed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Add NLS dependency to fix build errors, squash fix from ajd]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20230210080401.345462-25-ajd@linux.ibm.com
2023-02-13 22:34:33 +11:00
Reinette Chatre
2b129f0b24 PCI/MSI: Provide missing stubs for CONFIG_PCI_MSI=n
pci_msix_alloc_irq_at() and pci_msix_free_irq() are not declared when
CONFIG_PCI_MSI is disabled.

Users of these two calls do not yet exist but when users do appear (shown
below is an attempt to use the new API in vfio-pci) the following errors
will be encountered when compiling with CONFIG_PCI_MSI disabled:

drivers/vfio/pci/vfio_pci_intrs.c:461:4: error: implicit declaration of\
        function 'pci_msix_free_irq' is invalid in C99\
        [-Werror,-Wimplicit-function-declaration]
                           pci_msix_free_irq(pdev, msix_map);
                           ^
drivers/vfio/pci/vfio_pci_intrs.c:511:15: error: implicit declaration of\
        function 'pci_msix_alloc_irq_at' is invalid in C99\
        [-Werror,-Wimplicit-function-declaration]
                   msix_map = pci_msix_alloc_irq_at(pdev, vector, NULL);

Provide definitions for pci_msix_alloc_irq_at() and pci_msix_free_irq() in
preparation for users that need to compile when CONFIG_PCI_MSI is
disabled.

Reported-by: kernel test robot <lkp@intel.com>
Fixes: 34026364df ("PCI/MSI: Provide post-enable dynamic allocation interfaces for MSI-X")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/158e40e1cfcfc58ae30ecb2bbfaf86e5bba7a1ef.1675978686.git.reinette.chatre@intel.com
2023-02-13 12:17:20 +01:00
David S. Miller
9b0bf4f771 Merge branch 'ksz9477-eee-support'
Oleksij Rempel says:

====================
net: add EEE support for KSZ9477 switch family

changes v8:
- fix comment for linkmode_to_mii_eee_cap1_t() function
- add Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
- add Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>

changes v7:
- update documentation for genphy_c45_eee_is_active()
- address review comments on "net: dsa: microchip: enable EEE support"
  patch

changes v6:
- split patch set and send only first 9 patches
- Add Reviewed-by: Andrew Lunn <andrew@lunn.ch>
- use 0xffff instead of GENMASK
- Document @supported_eee
- use "()" with function name in comments

changes v5:
- spell fixes
- move part of genphy_c45_read_eee_abilities() to
  genphy_c45_read_eee_cap1()
- validate MDIO_PCS_EEE_ABLE register against 0xffff val.
- rename *eee_100_10000* to *eee_cap1*
- use linkmode_intersects(phydev->supported, PHY_EEE_CAP1_FEATURES)
  instead of !linkmode_empty()
- add documentation to linkmode/register helpers

changes v4:
- remove following helpers:
  mmd_eee_cap_to_ethtool_sup_t
  mmd_eee_adv_to_ethtool_adv_t
  ethtool_adv_to_mmd_eee_adv_t
  and port drivers from this helpers to linkmode helpers.
- rebase against latest net-next
- port phy_init_eee() to genphy_c45_eee_is_active()

changes v3:
- rework some parts of EEE infrastructure and move it to c45 code.
- add supported_eee storage and start using it in EEE code and by the
  micrel driver.
- add EEE support for ar8035 PHY
- add SmartEEE support to FEC i.MX series.

changes v2:
- use phydev->supported instead of reading MII_BMSR regiaster
- fix @get_eee > @set_eee

With this patch series we provide EEE control for KSZ9477 family of
switches and
AR8035 with i.MX6 configuration.
According to my tests, on a system with KSZ8563 switch and 100Mbit idle
link,
we consume 0,192W less power per port if EEE is enabled.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
8b68710a31 net: phy: start using genphy_c45_ethtool_get/set_eee()
All preparations are done. Now we can start using new functions and remove
the old code.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
6340f9fd43 net: phy: migrate phy_init_eee() to genphy_c45_eee_is_active()
Reduce code duplicated by migrating phy_init_eee() to
genphy_c45_eee_is_active().

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
5827b16812 net: phy: c45: migrate to genphy_c45_write_eee_adv()
Migrate from genphy_config_eee_advert() to genphy_c45_write_eee_adv().

It should work as before except write operation to the EEE adv registers
will be done only if some EEE abilities was detected.

If some driver will have a regression, related driver should provide own
.get_features callback. See micrel.c:ksz9477_get_features() as example.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
9b01c885be net: phy: c22: migrate to genphy_c45_write_eee_adv()
Migrate from genphy_config_eee_advert() to genphy_c45_write_eee_adv().

It should work as before except write operation to the EEE adv registers
will be done only if some EEE abilities was detected.

If some driver will have a regression, related driver should provide own
.get_features callback. See micrel.c:ksz9477_get_features() as example.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
022c3f87f8 net: phy: add genphy_c45_ethtool_get/set_eee() support
Add replacement for phy_ethtool_get/set_eee() functions.

Current phy_ethtool_get/set_eee() implementation is great and it is
possible to make it even better:
- this functionality is for devices implementing parts of IEEE 802.3
  specification beyond Clause 22. The better place for this code is
  phy-c45.c
- currently it is able to do read/write operations on PHYs with
  different abilities to not existing registers. It is better to
  use stored supported_eee abilities to avoid false read/write
  operations.
- the eee_active detection will provide wrong results on not supported
  link modes. It is better to validate speed/duplex properties against
  supported EEE link modes.
- it is able to support only limited amount of link modes. We have more
  EEE link modes...

By refactoring this code I address most of this point except of the last
one. Adding additional EEE link modes will need more work.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
cf9f607969 net: phy: export phy_check_valid() function
This function will be needed for genphy_c45_ethtool_get_eee() provided
by next patch.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
48fb19940f net: phy: micrel: add ksz9477_get_features()
KSZ8563R, which has same PHYID as KSZ9477 family, will change "EEE control
and capability 1" (Register 3.20) content depending on configuration of
"EEE advertisement 1" (Register 7.60). Changes on the 7.60 will affect
3.20 register.

So, instead of depending on register 3.20, driver should set supported_eee.

Proper supported_eee configuration is needed to make use of generic
PHY c45 set/get_eee functions provided by next patches.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
14e47d1fb8 net: phy: add genphy_c45_read_eee_abilities() function
Add generic function for EEE abilities defined by IEEE 802.3
specification. For now following registers are supported:
- IEEE 802.3-2018 45.2.3.10 EEE control and capability 1 (Register 3.20)
- IEEE 802.3cg-2019 45.2.1.186b 10BASE-T1L PMA status register
  (Register 1.2295)

Since I was not able to find any flag signaling support of these
registers, we should detect link mode abilities first and then based on
these abilities doing EEE link modes detection.

Results of EEE ability detection will be stored into new variable
phydev->supported_eee.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Oleksij Rempel
69d3b36ca0 net: dsa: microchip: enable EEE support
Some of KSZ9477 family switches provides EEE support. To enable it, we
just need to register set_mac_eee/set_mac_eee handlers and validate
supported chip version and port.

Currently supported chip variants are: KSZ8563, KSZ9477, KSZ9563,
KSZ9567, KSZ9893, KSZ9896, KSZ9897. KSZ8563 supports EEE only with
100BaseTX/Full.  Other chips support 100BaseTX/Full and 1000BaseTX/Full.
Low Power Idle configuration is not supported and currently not
documented in the datasheets.

EEE PHY specific tunings are not documented in the switch datasheets, but can
overlap with KSZ9131 specification.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:12:31 +00:00
Armin Wolf
6113bd5244 platform/x86: dell-ddv: Prefer asynchronous probing
During probe, both sensor buffers need to be queried to
initialize the hwmon channels. This might be slow on some
machines, causing a unnecessary delay during boot.
Mark the driver with PROBE_PREFER_ASYNCHRONOUS so that it
can be probed asynchronously.

Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20230209211503.2739-3-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:50 +01:00
Armin Wolf
3b7eeff93d platform/x86: dell-ddv: Add hwmon support
Thanks to bugreport 216655 on bugzilla triggered by the
dell-smm-hwmon driver, the contents of the sensor buffers
could be almost completely decoded.
Add an hwmon interface for exposing the fan and thermal
sensor values. Since the WMI interface can be quite slow
on some machines, the sensor buffers are cached for 1 second
to lessen the performance impact.
The debugfs interface remains in place to aid in reverse-engineering
of unknown sensor types and the thermal buffer.

Tested-by: Antonín Skala <skala.antonin@gmail.com>
Tested-by: Gustavo Walbon <gustavowalbon@gmail.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230209211503.2739-2-W_Armin@gmx.de
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:50 +01:00
Vadim Pasternak
e721056343 Documentation/ABI: Add new attribute for mlxreg-io sysfs interfaces
Add description for new attributes added for rack manager switch and
NG800 family systems.

Attributes related to power converter board:
- reset_pwr_converter_fail;
- pwr_converter_prog_en;
Attributes related to External Root of Trust (EROT) devices recovery:
- erot1_ap_reset;
- erot2_ap_reset;
- erot1_recovery;
- erot2_recovery;
- erot1_reset;
- erot2_reset;
- erot1_wp;
- erot2_wp;
- spi_chnl_select;
Attributes related to clock board failures and recovery:
- clk_brd1_boot_fail;
- clk_brd2_boot_fail;
- clk_brd_fail;
- clk_brd_prog_en;
Attributes related to power failures:
- reset_ac_ok_fail;
- asic_pg_fail;

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230208063331.15560-14-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:50 +01:00
Vadim Pasternak
50b823fdd3 platform: mellanox: mlx-platform: Move bus shift assignment out of the loop
Move assignment of bus shift setting out of the loop to avoid redundant
operation.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230208063331.15560-13-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:50 +01:00
Vadim Pasternak
cefdbc7815 platform: mellanox: mlx-platform: Add mux selection register to regmap
Extend writeable, readable, volatile registers of the 'regmap' object
with for I2C mux selector registers.

The motivation is to pass this object extended with selector registers
to I2C mux driver working over ‘regmap’.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230208063331.15560-12-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:50 +01:00
Vadim Pasternak
26917eab14 platform_data/mlxreg: Add field with mapped resource address
Add field with PCIe remapped based address for passing it across
relevant platform drivers sharing common system resources.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230208063331.15560-11-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:50 +01:00
Vadim Pasternak
26e118ea98 platform/mellanox: mlxreg-hotplug: Allow more flexible hotplug events configuration
Currently hotplug configuration in logic device assumes that all items
are provided with no holes.
Thus, any group of hotplug events, associated with the specific
status/event/mask registers is configured in those registers
successively from bit zero to bit #n (#n < 8).

This logic is changed int order to allow non-successive definition to
support configuration with the skipped bits – for example bits 3, 5, 7
in status/event/mask registers can be associated with hotplug events,
while others can be skipped.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230208063331.15560-10-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:50 +01:00
Vadim Pasternak
233fd7e44c platform: mellanox: Extend all systems with I2C notification callback
Motivation is to provide synchronization between I2C main bus and other
platform drivers using this notification callback.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230208063331.15560-9-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:50 +01:00
Vadim Pasternak
158cd83207 platform: mellanox: Split logic in init and exit flow
Split logic in mlxplat_init()/mlxplat_exit() routines.
Separate initialization of I2C infrastructure and others platform
drivers.

Motivation is to provide synchronization between I2C bus and mux
drivers and other drivers using this infrastructure.
I2C main bus and MUX busses are implemented in FPGA logic. On some new
systems the numbers allocated for these busses could be variable
depending on order of initialization of I2C native busses. Since bus
numbers are passed to some other platform drivers during initialization
flow, it is necessary to synchronize completion of I2C infrastructure
drivers and activation of rest of drivers.

Thus initialization flow will be performed in synchronized order.

Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Michael Shych <michaelsh@nvidia.com>
Link: https://lore.kernel.org/r/20230208063331.15560-8-vadimp@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2023-02-13 12:07:49 +01:00
David S. Miller
79cdf17e51 Merge branch 'ionic-on-chip-desc'
Shannon Nelson says:

====================
ionic: on-chip descriptors

We start with a couple of house-keeping patches that were originally
presented for 'net', then we add support for on-chip descriptor rings
for tx-push, as well as adding support for rx-push.

I have a patch for the ethtool userland utility that I can send out
once this has been accepted.

v4: added rx-push attributes to ethtool netlink
    converted CMB feature from using a priv-flag to using ethtool tx/rx-push

v3: edited commit message to describe interface-down limitation
    added warn msg if cmb_inuse alloc fails
    removed unnecessary clearing of phy_cmb_pages and cmb_npages
    changed cmb_rings_toggle to use cmb_inuse
    removed unrelated pci_set_drvdata()
    removed unnecessary (u32) cast
    added static inline func for writing CMB descriptors

v2: dropped the rx buffers patch
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:05:12 +00:00
Shannon Nelson
40bc471dc7 ionic: add tx/rx-push support with device Component Memory Buffers
The ionic device has on-board memory (CMB) that can be used
for descriptors as a way to speed descriptor access for faster
packet processing.  It is rumored to improve latency and/or
packets-per-second for some profiles of small packet traffic,
although your mileage may vary.

Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:05:12 +00:00
Shannon Nelson
5b4e9a7a71 net: ethtool: extend ringparam set/get APIs for rx_push
Similar to what was done for TX_PUSH, add an RX_PUSH concept
to the ethtool interfaces.

Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:05:12 +00:00
Shannon Nelson
896de449f8 ionic: remove unnecessary void casts
Minor Code cleanup details.

Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:05:11 +00:00
Shannon Nelson
7bb990097d ionic: remove unnecessary indirection
We have the pointer already, don't need to go through the
lif struct for it.

Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2023-02-13 11:05:11 +00:00
Herbert Xu
d3777ceaad tls: Pass rec instead of aead_req into tls_encrypt_done
The function tls_encrypt_done only uses aead_req to get ahold of
the tls_rec object.  So we could pass that in instead of aead_req
to simplify the code.

Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:15 +08:00
Herbert Xu
846366b0df crypto: api - Remove completion function scaffolding
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:15 +08:00
Herbert Xu
8580e55aa8 tls: Remove completion function scaffolding
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:15 +08:00
Herbert Xu
65cb4657ba tipc: Remove completion function scaffolding
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:15 +08:00
Herbert Xu
6002e20dd0 net: ipv6: Remove completion function scaffolding
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:15 +08:00
Herbert Xu
fd5dabf764 net: ipv4: Remove completion function scaffolding
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:15 +08:00
Herbert Xu
23b8b93ba9 net: macsec: Remove completion function scaffolding
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:15 +08:00
Herbert Xu
dcfe653d7c dm: Remove completion function scaffolding
This patch removes the temporary scaffolding now that the comletion
function signature has been converted.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:15 +08:00
Herbert Xu
255e48eb17 crypto: api - Use data directly in completion function
This patch does the final flag day conversion of all completion
functions which are now all contained in the Crypto API.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:14 +08:00
Herbert Xu
234650bd22 crypto: talitos - Use request_complete helpers
Use the request_complete helpers instead of calling the completion
function directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:14 +08:00
Herbert Xu
555c566131 crypto: sahara - Use request_complete helpers
Use the request_complete helpers instead of calling the completion
function directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:14 +08:00
Herbert Xu
e94c1c9b43 crypto: s5p-sss - Use request_complete helpers
Use the request_complete helpers instead of calling the completion
function directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:14 +08:00
Herbert Xu
0cbe89d5d1 crypto: qce - Use request_complete helpers
Use the request_complete helpers instead of calling the completion
function directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:14 +08:00
Herbert Xu
6c62186455 crypto: qat - Use request_complete helpers
Use the request_complete helpers instead of calling the completion
function directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:35:14 +08:00
Randy Dunlap
1e5b5df65a m68k: /proc/hardware should depend on PROC_FS
When CONFIG_PROC_FS is not set, there is a build error for an unused
function. Make PROC_HARDWARE depend on PROC_FS to prevent this error.

In file included from ../arch/m68k/kernel/setup.c:3:
../arch/m68k/kernel/setup_mm.c:477:12: error: 'hardware_proc_show' defined but not used [-Werror=unused-function]
  477 | static int hardware_proc_show(struct seq_file *m, void *v)
      |            ^~~~~~~~~~~~~~~~~~

Fixes: 66d857b08b ("m68k: merge m68k and m68knommu arch directories") # v3.0
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20230209010825.24136-1-rdunlap@infradead.org
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2023-02-13 11:34:49 +01:00
Herbert Xu
25c9d2c358 crypto: mxs-dcp - Use request_complete helpers
Use the request_complete helpers instead of calling the completion
function directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:34:49 +08:00
Herbert Xu
25085ba5a7 crypto: octeontx2 - Use request_complete helpers
Use the request_complete helpers instead of calling the completion
function directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:34:49 +08:00
Herbert Xu
d80bcdf297 crypto: octeontx - Use request_complete helpers
Use the request_complete helpers instead of calling the completion
function directly.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
2023-02-13 18:34:49 +08:00