This seems to be a new revision of the device. RGB controls have changed,
but this driver doesn't touch them anyway.
Fan speed control reported to be working with existing userspace (hidraw)
software, so I assume it's compatible. Fan channel count is the same.
Recently added (0x1e71, 0x2019) seems to be the same device.
Discovered in liquidctl project:
https://github.com/liquidctl/liquidctl/issues/541
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Link: https://lore.kernel.org/r/20230219105924.333007-1-mezin.alexander@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/hwmon/gpio-fan.c:484:34: error: ‘of_gpio_fan_match’ defined but not used [-Werror=unused-const-variable=]
Note(groeck): The build error is only seen if Kconfig dependencies
are messed up. The driver depends on OF_GPIO which should depend
on OF. This was temporarily broken in linux-next, and it was
possible to select CONFIG_OF=n and CONFIG_SENSORS_GPIO_FAN=y.
Nevertheless, this is a sensible fix.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312193723.478032-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Store Queue code allocates a bitmap buffer with the size of
multiple of sizeof(long) in sq_api_init(). While the buffer size
is calculated correctly, the code uses the wrong element size to
allocate the buffer which results in the allocated bitmap buffer
being too small.
Fix this by allocating the buffer with kcalloc() with element size
sizeof(long) instead of kzalloc() whose elements size defaults to
sizeof(char).
Fixes: d7c30c682a ("sh: Store Queue API rework.")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230419114854.528677-1-glaubitz@physik.fu-berlin.de
Add reference count checking to make sure of good use of get and put.
Add and use accessors to reduce RC_CHK clutter.
The only significant issue was in tests/thread-maps-share.c where
reference counts were released in the reverse order to acquisition,
leading to a use after put. This was fixed by reversing the put order.
Committer notes:
Extracted from a larger patch removing bits that were covered by the use
of pre-existing maps__ accessors (e.g. maps__nr_maps()) and new ones
added (maps__refcnt()) to reduce RC_CHK_ACCESS(maps)-> source code
pollution.
Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Riccardo Mancini <rickyman7@gmail.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Link: https://lore.kernel.org/lkml/20230407230405.2931830-5-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To remove one more direct access to 'struct maps' so that we can
intercept accesses to its instantiations and refcount check it to catch
use after free, etc.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
James Clark noticed that the recent 63df0e4bc3 ("perf map: Add
accessor for dso") patch accessed map->dso before the 'map' variable was
NULL checked, which is a change in logic that leads to segmentation
faults, so comb thru that patch to fix similar cases.
Fixes: 63df0e4bc3 ("perf map: Add accessor for dso")
Acked-by: Ian Rogers <irogers@google.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Clark <james.clark@arm.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: John Garry <john.g.garry@oracle.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/lkml/ZD68RYCVT8hqPuxr@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The cache information can be extracted from either a Device Tree(DT),
the PPTT ACPI table, or arch registers (clidr_el1 for arm64).
When the DT is used but no cache properties are advertised, the current
code doesn't correctly fallback to using arch information. The changes
fixes the same and also assuse the that L1 data/instruction caches
are private and L2/higher caches are shared when the cache information
is missing in DT/ACPI and is derived form clidr_el1/arch registers.
Currently the cacheinfo is built from the primary CPU prior to secondary
CPUs boot, if the DT/ACPI description contains cache information.
However, if not present, it still reverts to the old behavior, which
allocates the cacheinfo memory on each secondary CPUs which causes
RT kernels to triggers a "BUG: sleeping function called from invalid
context".
The changes here attempts to enable automatic detection for RT kernels
when no DT/ACPI cache information is available, by pre-allocating
cacheinfo memory on the primary CPU.
-----BEGIN PGP SIGNATURE-----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=4hhJ
-----END PGP SIGNATURE-----
Merge tag 'cacheinfo-updates-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into driver-core-next
Sudeep writes:
cacheinfo and arch_topology updates for v6.4
The cache information can be extracted from either a Device Tree(DT),
the PPTT ACPI table, or arch registers (clidr_el1 for arm64).
When the DT is used but no cache properties are advertised, the current
code doesn't correctly fallback to using arch information. The changes
fixes the same and also assuse the that L1 data/instruction caches
are private and L2/higher caches are shared when the cache information
is missing in DT/ACPI and is derived form clidr_el1/arch registers.
Currently the cacheinfo is built from the primary CPU prior to secondary
CPUs boot, if the DT/ACPI description contains cache information.
However, if not present, it still reverts to the old behavior, which
allocates the cacheinfo memory on each secondary CPUs which causes
RT kernels to triggers a "BUG: sleeping function called from invalid
context".
The changes here attempts to enable automatic detection for RT kernels
when no DT/ACPI cache information is available, by pre-allocating
cacheinfo memory on the primary CPU.
* tag 'cacheinfo-updates-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
Remove support for the already no more supported stih415 and stih416
platforms. Remove as well the stid127 platform which never made it
up to the kernel.
Signed-off-by: Alain Volmat <avolmat@me.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230416190501.18737-1-avolmat@me.com
This is a relatively smaller update for CoreSight tracing subsystem targeting
v6.4, with the following changes:
- Removing Mathieu Poirier as MAINTAINER for the subsystem, with updates to
CREDITS for his contributions.
- Fix CoreSight ETM PMU to set the module field
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
-----BEGIN PGP SIGNATURE-----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=YYDU
-----END PGP SIGNATURE-----
Merge tag 'coresight-next-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux into char-misc-next
Suzuki writes:
coresight: Updates for v6.4
This is a relatively smaller update for CoreSight tracing subsystem targeting
v6.4, with the following changes:
- Removing Mathieu Poirier as MAINTAINER for the subsystem, with updates to
CREDITS for his contributions.
- Fix CoreSight ETM PMU to set the module field
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
* tag 'coresight-next-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/coresight/linux:
coresight: etm_pmu: Set the module field
MAINTAINERS: Remove Mathieu Poirier as coresight maintainer
This pull request contains the interconnect changes for the 6.4-rc1 merge
window, which this time are mostly cleanups.
Core changes:
interconnect: Skip call into provider if initial bw is zero
interconnect: Use of_property_present() for testing DT property presence
interconnect: drop racy registration API
interconnect: drop unused icc_link_destroy() interface
Driver changes:
interconnect: qcom: Drop obsolete dependency on COMPILE_TEST
interconnect: qcom: drop obsolete OSM_L3/EPSS defines
interconnect: qcom: osm-l3: drop unuserd header inclusion
interconnect: qcom: rpm: drop bogus pm domain attach
interconnect: qcom: rpm: make QoS INVALID default
interconnect: qcom: rpm: Add support for specifying channel num
interconnect: qcom: Sort kerneldoc entries
dt-bindings: interconnect: OSM L3: Add SM6375 CPUCP compatible
dt-bindings: interconnect: qcom,msm8998-bwmon: Resolve MSM8998 support
Signed-off-by: Georgi Djakov <djakov@kernel.org>
-----BEGIN PGP SIGNATURE-----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=By6c
-----END PGP SIGNATURE-----
Merge tag 'icc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc into char-misc-next
Georgi writes:
interconnect changes for 6.4
This pull request contains the interconnect changes for the 6.4-rc1 merge
window, which this time are mostly cleanups.
Core changes:
interconnect: Skip call into provider if initial bw is zero
interconnect: Use of_property_present() for testing DT property presence
interconnect: drop racy registration API
interconnect: drop unused icc_link_destroy() interface
Driver changes:
interconnect: qcom: Drop obsolete dependency on COMPILE_TEST
interconnect: qcom: drop obsolete OSM_L3/EPSS defines
interconnect: qcom: osm-l3: drop unuserd header inclusion
interconnect: qcom: rpm: drop bogus pm domain attach
interconnect: qcom: rpm: make QoS INVALID default
interconnect: qcom: rpm: Add support for specifying channel num
interconnect: qcom: Sort kerneldoc entries
dt-bindings: interconnect: OSM L3: Add SM6375 CPUCP compatible
dt-bindings: interconnect: qcom,msm8998-bwmon: Resolve MSM8998 support
Signed-off-by: Georgi Djakov <djakov@kernel.org>
* tag 'icc-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/djakov/icc:
dt-bindings: interconnect: qcom,msm8998-bwmon: Resolve MSM8998 support
dt-bindings: interconnect: OSM L3: Add SM6375 CPUCP compatible
interconnect: qcom: Sort kerneldoc entries
interconnect: qcom: rpm: Add support for specifying channel num
interconnect: qcom: rpm: make QoS INVALID default
interconnect: qcom: rpm: drop bogus pm domain attach
interconnect: drop unused icc_link_destroy() interface
interconnect: drop racy registration API
interconnect: Use of_property_present() for testing DT property presence
interconnect: qcom: osm-l3: drop unuserd header inclusion
interconnect: qcom: drop obsolete OSM_L3/EPSS defines
interconnect: Skip call into provider if initial bw is zero
interconnect: qcom: Drop obsolete dependency on COMPILE_TEST
========
Core
----
- Removed the "mhi_poll()" API as there are no in-kernel users available at the
moment.
- Added range check for the CHDBOFF and ERDBOFF registers in case the device
reports bad values.
- Fixed the errno for the rest of the range checks to use -ERANGE.
- Modified the event ring handlers to ring the doorbell only if there are
any pending elements in the ring to process for the device.
- Removed the check for EE (Execution Environment) while processing the SYS_ERR
transition as it creates device recovery issues when SBL (Secondary
Bootloader) crashes early.
- Used mhi_tryset_pm_state() API to set the error state instead of open coding
if the firmware loading fails. This avoids the race with other pm_state
updates.
pci_generic
-----------
- Dropped the dedundant pci_{enable/disable}_pcie_error_reporting() calls from
driver probe's error path as the PCI core itself takes care of that now.
- Revered the commit 2d5253a096 ("bus: mhi: host: pci_generic: Add a secondary
AT port to Telit FN990") as it turned out to be erroneous. This happened due
to the patch adding secondary AT port for FN990 getting applied through NET
and MHI trees and this caused two commits for the same functionality but one
of them ended up wrong.
- Added support for Foxconn T99W510 modem based on SDX24 chipset from Qualcomm.
MHI Endpoint
============
- Demoted the channel not supported error log to debug as not all devices will
support all channels defined in MHI spec and this may spam users.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZ6VDKoFIy9ikWCeXVZ8R5v6RzvUFAmQ9B84ACgkQVZ8R5v6R
zvWiXQf/dCw6Y4AZpCJOynhm7yuD2iZF7hgZ5KtMkopndWdmLb+Rrn0tPi5Lufkq
/pbq1t0L09jPF2Bb9cvntnUSWW+YNww7TH6CtFn39StgYdkNGdyu3JS1AZai+0gl
5UHw3zUNLFC9StnNykoo+kgu8O5cmnwyQ4vfH/yJkkWqQFyHs7mZh1dcl1ej3ElF
/ETE3D51N9EQYHcE21p90oP7NSedb0/LhmtsUvS96ToB11DauoJGxrp/6bInBzgr
AnX/0i84KmzKg1EJpxIyrzeFzFYwt5wq0R9M7Bco0r77inxhXYmFYauf5ekZEY4M
I0SuIuIMkW4QpYYk1vx8niR8jQmVJw==
=pmPF
-----END PGP SIGNATURE-----
Merge tag 'mhi-for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi into char-misc-next
Manivannan writes:
MHI Host
========
Core
----
- Removed the "mhi_poll()" API as there are no in-kernel users available at the
moment.
- Added range check for the CHDBOFF and ERDBOFF registers in case the device
reports bad values.
- Fixed the errno for the rest of the range checks to use -ERANGE.
- Modified the event ring handlers to ring the doorbell only if there are
any pending elements in the ring to process for the device.
- Removed the check for EE (Execution Environment) while processing the SYS_ERR
transition as it creates device recovery issues when SBL (Secondary
Bootloader) crashes early.
- Used mhi_tryset_pm_state() API to set the error state instead of open coding
if the firmware loading fails. This avoids the race with other pm_state
updates.
pci_generic
-----------
- Dropped the dedundant pci_{enable/disable}_pcie_error_reporting() calls from
driver probe's error path as the PCI core itself takes care of that now.
- Revered the commit 2d5253a096 ("bus: mhi: host: pci_generic: Add a secondary
AT port to Telit FN990") as it turned out to be erroneous. This happened due
to the patch adding secondary AT port for FN990 getting applied through NET
and MHI trees and this caused two commits for the same functionality but one
of them ended up wrong.
- Added support for Foxconn T99W510 modem based on SDX24 chipset from Qualcomm.
MHI Endpoint
============
- Demoted the channel not supported error log to debug as not all devices will
support all channels defined in MHI spec and this may spam users.
* tag 'mhi-for-v6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mani/mhi:
bus: mhi: host: Use mhi_tryset_pm_state() for setting fw error state
bus: mhi: host: Remove duplicate ee check for syserr
bus: mhi: host: Avoid ringing EV DB if there are no elements to process
bus: mhi: pci_generic: Add Foxconn T99W510
bus: mhi: host: Use ERANGE for BHIOFF/BHIEOFF range check
bus: mhi: host: Range check CHDBOFF and ERDBOFF
bus: mhi: host: pci_generic: Revert "Add a secondary AT port to Telit FN990"
bus: mhi: host: pci_generic: Drop redundant pci_enable_pcie_error_reporting()
bus: mhi: ep: Demote unsupported channel error log to debug
bus: mhi: host: Remove mhi_poll() API
dev_err_probe() already display the error code. There is no need to
duplicate it explicitly in the error message.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/c167c16a535049d56f817bbede9c9f6f0a0f4c68.1681626553.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
If devm_request_irq() fails, then we are directly return 'ret' without
clk_disable_unprepare(sfc->clk) and clk_disable_unprepare(sfc->hclk).
Fix this by changing direct return to a goto 'err_irq'.
Fixes: 0b89fc0a36 ("spi: rockchip-sfc: add rockchip serial flash controller")
Signed-off-by: Li Lanzhe <u202212060@hust.edu.cn>
Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn>
Link: https://lore.kernel.org/r/20230419115030.6029-1-u202212060@hust.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
dma_request_slave_channel() may return NULL which will lead to
NULL pointer dereference error in 'tmp_chan->private'.
Correct this behaviour by, first, switching from deprecated function
dma_request_slave_channel() to dma_request_chan(). Secondly, enable
sanity check for the resuling value of dma_request_chan().
Also, fix description that follows the enacted changes and that
concerns the use of dma_request_slave_channel().
Fixes: 706e2c8811 ("ASoC: fsl_asrc_dma: Reuse the dma channel if available in Back-End")
Co-developed-by: Natalia Petrova <n.petrova@fintech.ru>
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230417133242.53339-1-n.zhandarovich@fintech.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
SAI on i.MX8QM platform supports the data lines up to 4. So the pins
setting should be corrected to 4.
Fixes: eba0f00775 ("ASoC: fsl_sai: Enable combine mode soft")
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Reviewed-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Link: https://lore.kernel.org/r/20230418094259.4150771-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Without the IFF_LIVE_ADDR_CHANGE flag being set, the network code
disallows changing the mac address while the interface is UP.
Consequences are, for instance, that the interface can't be used
in a failover bond.
Add the missing flag to net_device priv_flags.
Tested on Intel Elkhart Lake with default settings, as well as with
failover and alb mode bonds.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like the dependency got added accidentally in commit a553260618
("[PATCH] ISA DMA Kconfig fixes - part 3"). Unlike the previously removed
dmascc driver, the scc driver never used DMA.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization the driver issues a reset command via its command
interface in order to remove previous configuration from the device.
After issuing the reset, the driver waits for 200ms before polling on
the "system_status" register using memory-mapped IO until the device
reaches a ready state (0x5E). The wait is necessary because the reset
command only triggers the reset, but the reset itself happens
asynchronously. If the driver starts polling too soon, the read of the
"system_status" register will never return and the system will crash
[1].
The issue was discovered when the device was flashed with a development
firmware version where the reset routine took longer to complete. The
issue was fixed in the firmware, but it exposed the fact that the
current wait time is borderline.
Fix by increasing the wait time from 200ms to 400ms. With this patch and
the buggy firmware version, the issue did not reproduce in 10 reboots
whereas without the patch the issue is reproduced quite consistently.
[1]
mce: CPUs not responding to MCE broadcast (may include false positives): 0,4
mce: CPUs not responding to MCE broadcast (may include false positives): 0,4
Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler
Shutting down cpus with NMI
Kernel Offset: 0x12000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffbfffffff)
Fixes: ac004e8416 ("mlxsw: pci: Wait longer before accessing the device after reset")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
net: skbuff: hide some bitfield members
There is a number of protocol or subsystem specific fields
in struct sk_buff which are only accessed by one subsystem.
We can wrap them in ifdefs with minimal code impact.
This gives us a better chance to save a 2B and a 4B holes
resulting with the following savings (assuming a lucky
kernel config):
- /* size: 232, cachelines: 4, members: 28 */
- /* sum members: 227, holes: 1, sum holes: 4 */
- /* sum bitfield members: 8 bits (1 bytes) */
+ /* size: 224, cachelines: 4, members: 28 */
/* forced alignments: 2 */
- /* last cacheline: 40 bytes */
+ /* last cacheline: 32 bytes */
I think that the changes shouldn't be too controversial.
The only one I'm not 100% sure of is the SCTP one,
12 extra LoC for one bit.. But it did fit squarely
in the "this bit has only one user" category.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Simon Horman <horms@kernel.org>
Accesses to nf_trace and ipvs_property are already wrapped
by ifdefs where necessary. Don't allocate the bits for those
fields at all if possible.
Acked-by: Florian Westphal <fw@strlen.de>
Acked-by: Simon Horman <horms@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_trace is a debug feature, AFAIU, and yet it sits oddly
high in the sk_buff bitfield. Move it down, pushing up
dst_pending_confirm and inner_protocol_type.
Next change will make nf_trace optional (under Kconfig)
and all optional fields should be placed after 2b fields
to avoid 2b fields straddling bytes.
dst_pending_confirm is L3, so it makes sense next to ignore_df.
inner_protocol_type goes up just to keep the balance.
Acked-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_cpu is currently between 4 byte fields, so it's almost
guaranteed to create a 2B hole. It has a knock on effect of
creating a 4B hole after @end (and @end and @tail being in
different cachelines).
None of this matters hugely, but for kernel configs which
don't enable all the features there may well be a 2B hole
after the bitfield. Move alloc_cpu there.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP is not universally deployed, allow hiding its bit
from the skb.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datacenter kernel builds will very likely not include WIRELESS,
so let them shave 2 bits off the skb by hiding the wifi fields.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Marangi says:
====================
net: Add basic LED support for switch/phy
This is a continue of [1]. It was decided to take a more gradual
approach to implement LEDs support for switch and phy starting with
basic support and then implementing the hw control part when we have all
the prereq done.
This series implements only the brightness_set() and blink_set() ops.
An example of switch implementation is done with qca8k.
For PHY a more generic approach is used with implementing the LED
support in PHY core and with the user (in this case marvell) adding all
the required functions.
Currently we set the default-state as "keep" to not change the default
configuration of the declared LEDs since almost every switch have a
default configuration.
[1] https://lore.kernel.org/lkml/20230216013230.22978-1-ansuelsmth@gmail.com/
Changes in new series v7:
- Drop ethernet-leds schema and add unevaluatedProperties to
ethernet-controller and ethernet-phy schema
- Drop function-enumerator binding from schema example and DT
- Set devname_mandatory for qca8k leds and assign better name to LEDs
using the format {slave_mii_bus id}:0{port number}:{color}:{function}
- Add Documentation patch for Correct LEDs naming from Andrew
- Changes in Andrew patch:
- net: phy: Add a binding for PHY LEDs
- Convert index from u32 to u8
- net: phy: phy_device: Call into the PHY driver to set LED brightness
- Fixup kernel doc
- Convert index from u32 to u8
- net: phy: marvell: Add software control of the LEDs
- Convert index from u32 to u8
- net: phy: phy_device: Call into the PHY driver to set LED blinking
- Kernel doc fix
- Convert index from u32 to u8
- net: phy: marvell: Implement led_blink_set()
- Convert index from u32 to u8
Changes in new series v6:
- Add leds-ethernet.yaml to document reg in led node
- Update ethernet-controller and ethernet-phy to follow new leds-ethernet schema
- Fix comments in qca8k-leds.c (at least -> at most)
(wrong GENMASK for led phy 0 and 4)
- Add review and ack tag from Pavel Machek
- Changes in Andrew patch:
- leds: Provide stubs for when CLASS_LED & NEW_LEDS are disabled
- Change LED_CLASS to NEW_LEDS for led_init_default_state_get()
- net: phy: Add a binding for PHY LEDs
- Add dependency on LED_CLASS
- Drop review tag from Michal Kubiak (patch modified)
Changes in new series v5:
- Rebase everything on top of net-next/main
- Add more info on LED probe fail for qca8k
- Drop some additional raw number and move to define in qca8k header
- Add additional info on LED mapping on qca8k regs
- Checks port number in qca8k switch port parse
- Changes in Andrew patch:
- Add additional patch for stubs when CLASS_LED disabled
- Drop CLASS_LED dependency for PHYLIB (to fix kbot errors reported)
Changes in new series v4:
- Changes in Andrew patch:
- net: phy: Add a binding for PHY LEDs:
- Rename phy_led: led_list to list
- Rename phy_device: led_list to leds
- Remove phy_leds_remove() since devm_ should do what is needed
- Fixup documentation for struct phy_led
- Fail probe on LED errors
- net: phy: phy_device: Call into the PHY driver to set LED brightness
- Moved phy_led::phydev from previous patch to here since it is first
used here.
- net: phy: marvell: Implement led_blink_set()
- Use int instead of unsigned
- net: phy: marvell: Add software control of the LEDs
- Use int instead of unsigned
- Add depends on LED_CLASS for qca8k Kconfig
- Fix Makefile for qca8k as suggested
- Move qca8k_setup_led_ctrl to separate header
- Move Documentation from dsa-port to ethernet-controller
- Drop trailing . from Andrew patch fro consistency
Changes in new series v3:
- Move QCA8K_LEDS Kconfig option from tristate to bool
- Use new helper led_init_default_state_get for default-state in qca8k
- Drop cled_qca8k_brightness_get() as there isn't a good way to describe
the mode the led is currently in
- Rework qca8k_led_brightness_get() to return true only when LED is set
to always ON
Changes in new series v2:
- Add LEDs node for rb3011
- Fix rb3011 switch node unevaluated properties while running
make dtbs_check
- Fix a copypaste error in qca8k-leds.c for port 4 required shift
- Drop phy-handle usage for qca8k and use qca8k_port_to_phy()
- Add review tag from Andrew
- Add Christian Marangi SOB in each Andrew patch
- Add extra description for dsa-port stressing that PHY have no access
and LED are controlled by the related MAC
- Add missing additionalProperties for dsa-port.yaml and ethernet-phy.yaml
Changes from the old v8 series:
- Drop linux,default-trigger set to netdev.
- Dropped every hw control related patch and implement only
blink_set and brightness_set
- Add default-state to "keep" for each LED node example
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Network LEDs can exist in both the MAC and the PHY. Naming is
difficult because the netdev name is neither stable or unique, do to
commands like ip link set name eth42 dev eth0, and network
namesspaces.
Give some example names where the MAC and the PHY have unique names
based on device tree nodes, or PCI bus addresses.
Since the LED can be used for anything which Linux supports for LEDs,
avoid using names like activity or link, rather describe the location
on the RJ-45, of what the RJ-45 is expected to be used for, WAN/LAN
etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WAN port of the 370-RD has a Marvell PHY, with one LED on
the front panel.y List this LED in the device tree.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document support for LEDs node in phy and add an example for it.
PHY LED will have to match led pattern and should be treated as a
generic led.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Switch LED for each port for MikroTik RB3011UiAS-RM.
MikroTik RB3011UiAS-RM is a 10 port device with 2 qca8337 switch chips
connected.
It was discovered that in the hardware design all 3 Switch LED trace of
the related port is connected to the same LED. This was discovered by
setting to 'always on' the related led in the switch regs and noticing
that all 3 LED for the specific port (for example for port 1) cause the
connected LED for port 1 to turn on. As an extra test we tried enabling
2 different LED for the port resulting in the LED turned off only if
every led in the reg was off.
Aside from this funny and strange hardware implementation, the device
itself have one green LED for each port, resulting in 10 green LED one
for each of the 10 supported port.
Cc: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPQ8064 MikroTik RB3011UiAS-RM DT have currently unevaluted properties
in the 2 switch nodes. The bindings #address-cells and #size-cells are
redundant and cause warning for 'Unevaluated properties are not
allowed'.
Drop these bindings to mute these warning as they should not be there
from the start.
Cc: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Jonathan McDowell <noodles@earth.li>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs definition example for qca8k Switch Family to describe how they
should be defined for a correct usage.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document support for LEDs node in ethernet-controller.
Ethernet Controller may support different LEDs that can be configured
for different operation like blinking on traffic event or port link.
Also add some Documentation to describe the difference of these nodes
compared to PHY LEDs, since ethernet-controller LEDs are controllable
by the ethernet controller regs and the possible intergated PHY doesn't
have control on them.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell PHY can blink the LEDs, simple on/off. All LEDs blink at
the same rate, and the reset default is 84ms per blink, which is
around 12Hz.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be requested to perform hardware accelerated
blinking. Pass this to the PHY driver, if it implements the op.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a brightness function, so the LEDs can be controlled from
software using the standard Linux LED infrastructure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux LEDs can be software controlled via the brightness file in /sys.
LED drivers need to implement a brightness_set function which the core
will call. Implement an intermediary in phy_device, which will call
into the phy driver if it implements the necessary function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define common binding parsing for all PHY drivers with LEDs using
phylib. Parse the DT as part of the phy_probe and add LEDs to the
linux LED class infrastructure. For the moment, provide a dummy
brightness function, which will later be replaced with a call into the
PHY driver. This allows testing since the LED core might otherwise
reject an LED whose brightness cannot be set.
Add a dependency on LED_CLASS. It either needs to be built in, or not
enabled, since a modular build can result in linker errors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide stubs for devm_led_classdev_register_ext() and
led_init_default_state_get() so that LED drivers embedded within other
drivers such as PHYs and Ethernet switches still build when LEDS_CLASS
or NEW_LEDS are disabled. This also helps with Kconfig dependencies,
which are somewhat hairy for phylib and mdio and only get worse when
adding a dependency on LED_CLASS.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs blink_set() support to qca8k Switch Family.
These LEDs support hw accellerated blinking at a fixed rate
of 4Hz.
Reject any other value since not supported by the LEDs switch.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add LEDs basic support for qca8k Switch Family by adding basic
brightness_set() support.
Since these LEDs refelect port status, the default label is set to
":port". DT binding should describe the color and function of the
LEDs using standard LEDs api.
Each LED always have the device name as prefix. The device name is
composed from the mii bus id and the PHY addr resulting in example
names like:
- qca8k-0.0:00:amber:lan
- qca8k-0.0:00:white:lan
- qca8k-0.0:01:amber:lan
- qca8k-0.0:01:white:lan
These LEDs supports only blocking variant of the brightness_set()
function since they can sleep during access of the switch leds to set
the brightness.
While at it add to the qca8k header file each mode defined by the Switch
Documentation for future use.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move qca8k_port_to_phy() to qca8k header as it's useful for future
reference in Switch LEDs module since the same logic is applied to get
the right index of the switch port.
Make it inline as it's simple function that just decrease the port.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our use-case needs two AT ports available:
One for running a ppp daemon, and another one for management
This patch enables a second AT port on DATA1
Signed-off-by: Jaime Breva <jbreva@nayarsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(struct nf_conn)->timeout is an interval before the conntrack
confirmed. After confirmed, it becomes a timestamp.
It is observed that timeout of an unconfirmed conntrack:
- Set by calling ctnetlink_change_timeout(). As a result,
`nfct_time_stamp` was wrongly added to `ct->timeout` twice.
- Get by calling ctnetlink_dump_timeout(). As a result,
`nfct_time_stamp` was wrongly subtracted.
Call Trace:
<TASK>
dump_stack_lvl
ctnetlink_dump_timeout
__ctnetlink_glue_build
ctnetlink_glue_build
__nfqnl_enqueue_packet
nf_queue
nf_hook_slow
ip_mc_output
? __pfx_ip_finish_output
ip_send_skb
? __pfx_dst_output
udp_send_skb
udp_sendmsg
? __pfx_ip_generic_getfrag
sock_sendmsg
Separate the 2 cases in:
- Setting `ct->timeout` in __nf_ct_set_timeout().
- Getting `ct->timeout` in ctnetlink_dump_timeout().
Pablo appends:
Update ctnetlink to set up the timeout _after_ the IPS_CONFIRMED flag is
set on, otherwise conntrack creation via ctnetlink breaks.
Note that the problem described in this patch occurs since the
introduction of the nfnetlink_queue conntrack support, select a
sufficiently old Fixes: tag for -stable kernel to pick up this fix.
Fixes: a4b4766c3c ("netfilter: nfnetlink_queue: rename related to nfqueue attaching conntrack info")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----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=IcG3
-----END PGP SIGNATURE-----
Merge tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Mika writes:
thunderbolt: Changes for v6.4 merge window
This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:
- Refactoring of DROM read code paths
- Convert to use SI units from units.h
- A couple of cleanups
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Introduce usb4_port_sb_opcode_err_to_errno() helper
thunderbolt: Make use of SI units from units.h
thunderbolt: Get rid of redundant 'else'
thunderbolt: Refactor DROM reading
thunderbolt: use `tb_eeprom_get_drom_offset` to discover DROM offset
Addresses the following warning when building sdk7786_defconfig:
arch/sh/drivers/pci/pcie-sh7786.c:34:22: warning: 'dma_pfn_offset' defined but not used [-Wunused-variable]
34 | static unsigned long dma_pfn_offset;
| ^~~~~~~~~~~~~~
Fixes: e0d072782c ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230419070934.422997-1-glaubitz@physik.fu-berlin.de
Unfortunately, the tester gave a weak feedback (working/non-working) for
this case. After the double confirmation, this change is not really required.
The standard code with alc269_fallback_pin_fixup_tbl should work on this
hardware.
Fixes: 5911d78fab ("ALSA: hda/realtek: Improve support for Dell Precision 3260")
Fixes: 5f4efc9dfc ("ALSA: hda/realtek: Fix support for Dell Precision 3260")
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230419081121.304846-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware SDO has issue to fill txd for the moment, so fallback to
driver filling method.
Fixes: 98686cd216 (wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices)
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
