There is currently no return check for writing an authentication
type (HERMES_AUTH_SHARED_KEY or HERMES_AUTH_OPEN). It looks like
it was accidentally skipped.
This patch adds a return check similar to the other checks in
__orinoco_hw_setup_enc() for hermes_write_wordrec().
Detected using the static analysis tool - Svace.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221227133306.201356-1-aleksei.kodanev@bell-sw.com
The wifi + bluetooth combo chip RTL8723BU can leak memory (especially?)
when it's connected to a bluetooth audio device. The busy bluetooth
traffic generates lots of C2H (card to host) messages, which are not
freed correctly.
To fix this, move the dev_kfree_skb() call in rtl8xxxu_c2hcmd_callback()
inside the loop where skb_dequeue() is called.
The RTL8192EU leaks memory because the C2H messages are added to the
queue and left there forever. (This was fine in the past because it
probably wasn't sending any C2H messages until commit e542e66b7c
("wifi: rtl8xxxu: gen2: Turn on the rate control"). Since that commit
it sends a C2H message when the TX rate changes.)
To fix this, delete the check for rf_paths > 1 and the goto. Let the
function process the C2H messages from RTL8192EU like the ones from
the other chips.
Theoretically the RTL8188FU could also leak like RTL8723BU, but it
most likely doesn't send C2H messages frequently enough.
This change was tested with RTL8723BU by Erhard F. I tested it with
RTL8188FU and RTL8192EU.
Reported-by: Erhard F. <erhard_f@mailbox.org>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215197
Fixes: e542e66b7c ("rtl8xxxu: add bluetooth co-existence support for single antenna")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/03b099c1-c671-d252-36f4-57b70d721f9d@gmail.com
The last_pg is wrong, it is actually the first page of the last
scatterlist element. To get the last page of the last scatterlist element
we have to add prv->length. So it is checking mergability against the
wrong page, Further, a SG element is not guaranteed to end on a page
boundary, so we have to check the sub page location also for merge
eligibility.
Fix the above by checking physical contiguity based on PFNs, compute the
actual last page and then call pages_are_mergable().
Fixes: 1567b49d1a ("lib/scatterlist: add check when merging zone device pages")
Link: https://lore.kernel.org/r/20230111101054.188136-1-yishaih@nvidia.com
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Fix W=1 kernel-doc warning:
kernel/printk/printk.c:
- Include function parameter in console_lock_spinning_disable_and_check()
Signed-off-by: Anuradha Weeraman <anuradha@debian.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230116125635.374567-1-anuradha@debian.org
The revert of the removal of this driver happened after we fixed up
the split limits for NOWAIT issue, hence it got missed. Ensure that
we check for a NULL bio after splitting, in case it should be retried.
Marking this as fixing both commits, so that stable backport will do
this correctly.
Cc: stable@vger.kernel.org
Fixes: 9cea62b2cb ("block: don't allow splitting of a REQ_NOWAIT bio")
Fixes: 4b83e99ee7 ("Revert "pktcdvd: remove driver."")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Several mutexes are taken while setting up console serial ports. In
particular, the tty_port->mutex and @console_mutex are taken:
serial_pnp_probe
serial8250_register_8250_port
uart_add_one_port (locks tty_port->mutex)
uart_configure_port
register_console (locks @console_mutex)
In order to synchronize kgdb's tty_find_polling_driver() with
register_console(), commit 6193bc9084 ("tty: serial: kgdboc:
synchronize tty_find_polling_driver() and register_console()") takes
the @console_mutex. However, this leads to the following call chain
(with locking):
platform_probe
kgdboc_probe
configure_kgdboc (locks @console_mutex)
tty_find_polling_driver
uart_poll_init (locks tty_port->mutex)
uart_set_options
This is clearly deadlock potential due to the reverse lock ordering.
Since uart_set_options() requires holding @console_mutex in order to
serialize early initialization of the serial-console lock, take the
@console_mutex in uart_poll_init() instead of configure_kgdboc().
Since configure_kgdboc() was using @console_mutex for safe traversal
of the console list, change it to use the SRCU iterator instead.
Add comments to uart_set_options() kerneldoc mentioning that it
requires holding @console_mutex (aka the console_list_lock).
Fixes: 6193bc9084 ("tty: serial: kgdboc: synchronize tty_find_polling_driver() and register_console()")
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>
[pmladek@suse.com: Export console_srcu_read_lock_is_held() to fix build kgdboc as a module.]
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20230112161213.1434854-1-john.ogness@linutronix.de
Take into account possible error conditions of mt76_rx_token_consume
routine in mt7915_mmio_wed_init_rx_buf() and mt76_dma_add_buf()
Fixes: cd372b8c99 ("wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf")
Fixes: 4f831d18d1 ("wifi: mt76: mt7915: enable WED RX support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 96f134dc19)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113105848.34642-2-nbd@nbd.name
Do not increment queue head if mt76_dma_add_buf fails for Wireless
Ethernet Dispatcher rx queues.
Fixes: cd372b8c99 ("wifi: mt76: add WED RX support to mt76_dma_{add,get}_buf")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit fe13dad899)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113105848.34642-1-nbd@nbd.name
... to avoid the mess of conditional preprocessing as we are continually
adding fscache related mount options.
Reviewd-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230112065431.124926-3-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Since the EROFS share domain feature for fscache mode has been available
since Linux v6.1, let's add documentation for 'domain_id' mount option.
Cc: linux-doc@vger.kernel.org
Reviewed-by: Jia Zhu <zhujia.zj@bytedance.com>
Signed-off-by: Jingbo Xu <jefflexu@linux.alibaba.com>
Reviewed-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Reviewed-by: Chao Yu <chao@kernel.org>
Link: https://lore.kernel.org/r/20230112065431.124926-2-jefflexu@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
The EFI runtime services run from a dedicated stack now, and so the
stack unwinder needs to be informed about this.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Comparing current_work() against efi_rts_work.work is sufficient to
decide whether current is currently running EFI runtime services code at
any level in its call stack.
However, there are other potential users of the EFI runtime stack, such
as the ACPI subsystem, which may invoke efi_call_virt_pointer()
directly, and so any sync exceptions occurring in firmware during those
calls are currently misidentified.
So instead, let's check whether the stashed value of the thread stack
pointer points into current's thread stack. This can only be the case if
current was interrupted while running EFI runtime code. Note that this
implies that we should clear the stashed value after switching back, to
avoid false positives.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The driver doesn't depend on the OF to be complied. Hence
the proper header to use is mod_devicetable.h. Replace of*.h with
the above mentioned and drop redundant dependency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/20230113143640.24302-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The of_gpio_n_cells default is 2 when ->of_xlate() callback is
not defined. No need to assign it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Link: https://lore.kernel.org/r/20230113143640.24302-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The of_gpio_n_cells default is 2 when ->of_xlate() callback is
not defined. No need to assign it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230112185122.45216-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The of_gpio_n_cells default is 2 when ->of_xlate() callback is
not defined. No need to assign it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230112184923.80442-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The of_gpio_n_cells default is 2 when ->of_xlate() callback is
not defined. No need to assign it explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230112184340.79606-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not every function can be muxed to a group. Add proper binding which
documents which function can be muxed to a group or set of groups.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20221231160849.40544-7-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not every function can be muxed to a group. Add proper binding which
documents which function can be muxed to a group or set of groups.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20221231160849.40544-6-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not every function can be muxed to a group. Add proper binding which
documents which function can be muxed to a group or set of groups.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20221231160849.40544-5-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not every function can be muxed to a group. Add proper binding which
documents which function can be muxed to a group or set of groups.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20221231160849.40544-4-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not every function can be muxed to a group. Add proper binding which
documents which function can be muxed to a group or set of groups.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20221231160849.40544-3-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These variables define a list of functions which can be muxed to the pin
group which the name of the pin group was originally intended to be pointed
out on the name of the said variables.
Therefore, rename "func" to "grp" across all subdrivers where this applies.
Fixes: 18653d4bd8 ("pinctrl: ralink: rename variable names for functions on MT7620 and MT7621")
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20221231160849.40544-2-arinc.unal@arinc9.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Steen Hegelund says:
====================
net: microchip: Add support for two classes of VCAP rules
This adds support for two classes of VCAP rules:
- Permanent rules (added e.g. for PTP support)
- TC user rules (added by the TC userspace tool)
For this to work the VCAP Loopups must be enabled from boot, so that the
"internal" clients like PTP can add rules that are always active.
When the TC tool add a flower filter the VCAP rule corresponding to this
filter will be disabled (kept in memory) until a TC matchall filter creates
a link from chain 0 to the chain (lookup) where the flower filter was
added.
When the flower filter is enabled it will be written to the appropriate
VCAP lookup and become active in HW.
Likewise the flower filter will be disabled if there is no link from chain
0 to the chain of the filter (lookup), and when that happens the
corresponding VCAP rule will be read from the VCAP instance and stored in
memory until it is deleted or enabled again.
Version History:
================
v4 Removed a leftover 'Fixes' tag from v2. No functional changes.
v3 Removed the change that allowed rules to always be added in the
LAN996x even though the lookups are not enabled (Horatiu Vultur).
This was sent separately to net instead.
Removed the 'Fixes' tags due to the patch sent to net by Horatiu
Vultur.
Added a check for validity of the chain source when enabling a
lookup.
v2 Adding a missing goto exit in vcap_add_rule (Dan Carpenter).
Added missing checks for error returns in vcap_enable_rule.
v1 Initial version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This supports that individual rules are enabled and disabled via chain
information.
This is done by keeping disabled rules in the VCAP list (cached) until they
are enabled, and only at this time are the rules written to the VCAP HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a VCAP rule to be in one of 3 states:
- permanently stored in the VCAP HW (for rules that must always be present)
- enabled (stored in HW) when the corresponding lookup has been enabled
- disabled (stored in SW) when the lookup is disabled
This way important VCAP rules can be added even before the user enables the
VCAP lookups using a TC matchall filter.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the way the chain information verified when adding a new tc
flower filter.
When adding a flower filter it is now checked that the filter contains a
goto action to one of the IS2 VCAP lookups, except for the last lookup
which may omit this goto action.
It is also checked if you attempt to add multiple matchall filters to
enable the same VCAP lookup. This will be rejected.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds both the source and destination chain id to the information kept
for enabled port lookups.
This allows enabling and disabling a chain of lookups by walking the chain
information for a port.
This changes the way that VCAP lookups are enabled from userspace: instead
of one matchall rule that enables all the 4 Sparx5 IS2 lookups, you need a
matchall rule per lookup.
In practice that is done by adding one matchall rule in chain 0 to goto IS2
Lookup 0, and then for each lookup you add a rule per lookup (low priority)
that does a goto to the next lookup chain.
Examples:
If you want IS2 Lookup 0 to be enabled you add the same matchall filter as
before:
tc filter add dev eth12 ingress chain 0 prio 1000 handle 1000 matchall \
skip_sw action goto chain 8000000
If you also want to enable lookup 1 to 3 in IS2 and chain them you need
to add the following matchall filters:
tc filter add dev eth12 ingress chain 8000000 prio 1000 handle 1000 \
matchall skip_sw action goto chain 8100000
tc filter add dev eth12 ingress chain 8100000 prio 1000 handle 1000 \
matchall skip_sw action goto chain 8200000
tc filter add dev eth12 ingress chain 8200000 prio 1000 handle 1000 \
matchall skip_sw action goto chain 8300000
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion to the platform specific multi-word format is moved from the
key/action add functions to the encoding key/action.
This allows rules that are disabled (not in VCAP HW) to use the same format
for keys/actions as rules that have just been read from VCAP HW.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes the VCAP lookups state to always be enabled so that it is
possible to add "internal" VCAP rules that must be available even though
the user has not yet enabled the VCAP chains via a TC matchall filter.
The API callback to enable and disable VCAP lookups is therefore removed.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a rule counter is external to the VCAP such as the Sparx5 IS2 counters
are, then this counter must be reset when a new rule is created.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency the VCAP cache area is erased just before the new rule is
being encoded.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang says:
====================
l2tp: fix race conditions in l2tp_tunnel_register()
This patchset contains two patches, the first one is a preparation for
the second one which is the actual fix. Please find more details in
each patch description.
I have ran the l2tp test (https://github.com/katalix/l2tp-ktest),
all test cases are passed.
v3: preserve EEXIST errno for user-space
v2: move IDR allocation to l2tp_tunnel_register()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code in l2tp_tunnel_register() is racy in several ways:
1. It modifies the tunnel socket _after_ publishing it.
2. It calls setup_udp_tunnel_sock() on an existing socket without
locking.
3. It changes sock lock class on fly, which triggers many syzbot
reports.
This patch amends all of them by moving socket initialization code
before publishing and under sock lock. As suggested by Jakub, the
l2tp lockdep class is not necessary as we can just switch to
bh_lock_sock_nested().
Fixes: 37159ef2c1 ("l2tp: fix a lockdep splat")
Fixes: 6b9f34239b ("l2tp: fix races in tunnel creation")
Reported-by: syzbot+52866e24647f9a23403f@syzkaller.appspotmail.com
Reported-by: syzbot+94cc2a66fc228b23f360@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Guillaume Nault <gnault@redhat.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Parkin <tparkin@katalix.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp uses l2tp_tunnel_list to track all registered tunnels and
to allocate tunnel ID's. IDR can do the same job.
More importantly, with IDR we can hold the ID before a successful
registration so that we don't need to worry about late error
handling, it is not easy to rollback socket changes.
This is a preparation for the following fix.
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Guillaume Nault <gnault@redhat.com>
Cc: Jakub Sitnicki <jakub@cloudflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tom Parkin <tparkin@katalix.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ASPM issues may result in the NIC not being accessible any longer.
In this case disabling ASPM may not work. Therefore detect this case
by checking whether register reads return ~0, and try to make the
NIC accessible again by resetting the secondary bus.
v2:
- add exception handling for the case that pci_reset_bus() fails
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurations, wde_qempty_acq_num and wde_qempty_mgq_sel, are used
when MAC checks if TX queues are empty. Fill the corresponding setting
for 8852B.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-5-pkshih@realtek.com
TX BD's RAM table describes how HW allocates usable buffer section
for each TX channel at fetch time. The total RAM size for TX BD is
chip-dependent. For 8852BE, it has only half size (32) for TX channels
of single band. Original table arrange total size (64) for dual band.
It will overflow on 8852BE circuit and cause section conflicts between
different TX channels.
So, we do the changes below.
* add another table for single band chip and export both kind of tables
* point to the expected one in rtw89_pci_info by chip
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-4-pkshih@realtek.com
Some hardware modules don't have good RF characteristic as regular.
It could get ADC abnormal in low temperature, and it causes bad RX
performance and affects calibration result of DPK.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-3-pkshih@realtek.com
This change fixes the precision of CFO and TX EVM, and it could imporve
performance in some cases. Also, use the correctted definition for 8852A.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230113090632.60957-2-pkshih@realtek.com
The mac_id of management frames should follow rtwvif->mac_id or
rtwsta->mac_id. Add this patch to set the correct mac_id and
prevent unexpected behavior.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106121517.19841-2-pkshih@realtek.com
When transmitting a packet that gets from ieee80211_nullfunc_get(),
the vif in tx_info->control was no assigned, which will cause
dereferencing a null pointer.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106121517.19841-1-pkshih@realtek.com
The Wi-Fi role info structure will need to H2C to firmware, firmware
need these information to do some multi-role operation. v1 add DBCC
and NOA information in the structure. And driver side also need to
put/get values at the corresponding version of structure.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-8-pkshih@realtek.com
RTL8852B support the new features like TDMA instant (Change TDMA mechanism
immediately), Co-RX feature (Wi-Fi/Bluetooth can RX in the same time) and
so on. The v1 TDMA policy will enable those newer mechanism. It will have
a better coexistence performance.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230106120844.17441-7-pkshih@realtek.com