On DSA/IAX 1.0, TC-A and TC-B in GRPCFG are set as 1 to have best
performance and cannot be changed through sysfs knobs unless override
option is given.
The same values should be set on DSA 2.0 as well.
Fixes: ea7c8f598c ("dmaengine: idxd: restore traffic class defaults after wq reset")
Fixes: ade8a86b51 ("dmaengine: idxd: Set defaults for GRPCFG traffic class")
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20221209172141.562648-1-fenghua.yu@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The function set_completion_address is defined in the dma.c file, but not
called elsewhere, so remove this unused function.
drivers/dma/idxd/dma.c:66:20: warning: unused function 'set_completion_address'.
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3416
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20221212033514.5831-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rx operation on SPI GSI DMA is currently not working.
As per GSI spec, link_rx bit is to be set on GO TRE on tx
channel whenever there is going to be a DMA TRE on rx
channel. This is currently set for duplex operation only.
Set the bit for rx operation as well.
This is part of changes required to bring up Rx.
Fixes: 94b8f0e58f ("dmaengine: qcom: gpi: set chain and link flag for duplex")
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/1671212293-14767-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
BCDMA CSI RX present on AM62Ax SoC is a dedicated DMA for servicing
Camera Serial Interface (CSI) IP. Add support for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221213164304.1126945-6-vigneshr@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AM62A SoC has a BCDMA and PKTDMA as systems DMAs for service various
peripherals similar to AM64 SoC. Add support for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221213164304.1126945-5-vigneshr@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reusing loop iterator fails if BCHAN is not present as iterator is
uninitialized
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221213164304.1126945-3-vigneshr@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
AM62A SoC has a dedicated BCDMA that serves Camera Serial Interface
(CSI) IP. Add new compatible for the same. Unlike system
BCDMA, this instance only has RX DMA channels and lack TX or block copy
channel. Thus make those properties optional. Additionally CSI RX has
independent power domain, add the binding for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20221213164304.1126945-2-vigneshr@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Convert the MXS DMA binding to DT schema format using json-schema.
Drop "interrupt-names" property, since it is broken. The drivers/dma/mxs-dma.c
in Linux kernel does not use it, the property contains duplicate array entries
in existing DTs, and even malformed entries (gmpi, should have been gpmi). Get
rid of that optional property altogether.
Update example node names to be standard dma-controller@ ,
add global interrupt-parent property into example.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221219093713.328776-1-marex@denx.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Document compatibility for this GPI DMA controller on SM6125.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
[Marijn: Move compatible to the list with qcom,sdm845-gpi-dma]
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221222194600.139854-2-marijn.suijten@somainline.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move the 'thermal-zones' node after the regulator nodes to restore the
root-node sort order (alphabetically by node name).
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221227170202.21618-1-johan+linaro@kernel.org
Add region for memory hole present on bullhead in order to
fix a reboot issue on recent kernels
Reported-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Dominik Kobinski <dominikkobinski314@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221211100501.82323-1-dominikkobinski314@gmail.com
On eMMC devices, the UFS clocks aren't started in the bootloader (or well,
at least it should not be, as that would just leak power..), which results
in platform reboots when trying to access the unclocked UFS hardware,
which unfortunately happens on each and every boot, as interconnect calls
sync_state and goes over each and every path.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> #db820c
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221210200353.418391-6-konrad.dybcio@linaro.org
The volume-up button on both kumanos (Xperia 1 and Xperia 5) are mapped
to resin.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221210142525.16974-3-konrad.dybcio@linaro.org
With the recent patch that allowed us to reset the SDHCI controller from
Linux, things started working properly. Enable SDHCI1, and by extension
eMMC. Also, remove the now-useless cmdline SDHCI quirks.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221210141000.14344-1-konrad.dybcio@linaro.org
The sound and codec nodes are not a property of a soc, but rather board
as it describes the sound configuration. It also does not have unit
address:
sm8250-hdk.dtb: soc@0: sound: {} should not be valid under {'type': 'object'}
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221210115704.97614-4-krzysztof.kozlowski@linaro.org
The sound node is not a property of a soc, but rather board as it
describes the sound configuration. It also does not have unit address:
sdm845-shift-axolotl.dtb: soc@0: sound: {} should not be valid under {'type': 'object'}
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221210115704.97614-3-krzysztof.kozlowski@linaro.org
The SoC node is a simple-bus and its schema expect to have nodes only
with unit addresses:
sdm850-lenovo-yoga-c630.dtb: soc@0: opp-table-qup: {'compatible': ['operating-points-v2'], 'phandle': [[60]], 'opp-50000000':
... 'required-opps': [[55]]}} should not be valid under {'type': 'object'}
Move to top-level OPP tables:
- DSI and QUP which are shared between multiple nodes,
- QSPI which cannot be placed in its node due to address/size cells.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221210115704.97614-2-krzysztof.kozlowski@linaro.org
The SoC node is a simple-bus and its schema expect to have nodes only
with unit addresses:
sc7180-trogdor-lazor-r3.dtb: soc@0: opp-table-qspi: {'compatible': ['operating-points-v2'], 'phandle': [[186]], 'opp-75000000':
... 'required-opps': [[47]]}} should not be valid under {'type': 'object'}
Move to top-level OPP tables:
- QUP which is shared between multiple nodes,
- QSPI which cannot be placed in its node due to address/size cells.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221210115704.97614-1-krzysztof.kozlowski@linaro.org
Fix up the ramoops node to make it match bindings and style:
- remove "removed-dma-pool"
- don't pad size to 8 hex digits
- change cc-size to ecc-size so that it's used
- increase ecc-size from to 16
- remove the zeroed ftrace-size
Fixes: 5f82b9cda6 ("arm64: dts: qcom: Add SM6350 device tree")
Reported-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221210102600.589028-1-konrad.dybcio@linaro.org
The gpio node in PMIC dts'es define access to multiple GPIOs. Most Qcom
PMICs were already using the plural _gpios label to point to this node,
but a few PMICs were left behind including the recently-pulled
pm(i)8950.
Rename it from *_gpio to *_gpios for pm6125, pm6150(l), pm8005,
pm(i)8950, and pm(i)8998.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209220450.1793421-1-marijn.suijten@somainline.org
This patch does following:
1. Adds a new cros-ec-uart driver. This driver can send EC requests on
UART and process response packets received on UART transport.
2. Once probed, this driver will initialize the serdev device based on
the underlying information in the ACPI resource. After serdev device
properties are set, this driver will register itself cros-ec.
3. High level driver can use this implementation to talk to ChromeOS
Embedded Controller device in case it supports UART as transport.
4. When cros-ec driver initiates a request packet, outgoing message is
processed in buffer and sent via serdev. Once bytes are sent, driver
enables a wait_queue.
5. Since ChromeOS EC device sends response asynchronously, AP's TTY
driver accumulates response bytes and calls the registered callback.
TTY driver can send multiple callback for bytes ranging from 1 to MAX
bytes supported by EC device.
6. Driver waits for EC_MSG_DEADLINE_MS to collect and process received
bytes. It wakes wait_queue if expected bytes are received or else
wait_queue timeout. Based on the error condition, driver returns
data_len or error to cros_ec.
Signed-off-by: Bhanu Prakash Maiya <bhanumaiya@chromium.org>
Co-developed-by: Mark Hasemeyer <markhas@chromium.org>
Signed-off-by: Mark Hasemeyer <markhas@chromium.org>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20221227123212.v13.1.If7926fcbad397bc6990dd725690229bed403948c@changeid
This was pointed out in review but never followed up on thanks to
sidetracked discussions about labels vs node names.
Fixes: 0d97fdf380 ("arm64: dts: qcom: Add configuration for PMI8950 peripheral")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209215437.1783067-1-marijn.suijten@somainline.org
The framebuffer configuration for kumano griffin, written in kumano dtsi
(which is overwritten in bahamut dts for its smaller panel) has to use a
1096x2560 configuration as this is what the panel (and framebuffer area)
has been initialized to. Downstream userspace also has access to (and
uses) this 2.5k mode by default, and only switches the panel to 4k when
requested.
Fixes: d0a6ce59ea ("arm64: dts: qcom: sm8150: Add support for SONY Xperia 1 / 5 (Kumano platform)")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209191733.1458031-1-marijn.suijten@somainline.org
Now that we've added the `off-on-delay-us` for the touchpanel
regulator, we can see that we're actually hitting that delay at
bootup. I saw about 200 ms of delay.
Let's avoid that delay by starting the regulator on. We'll only do
this for eDP devices for the time being.
NOTE: we _won't_ do this for homestar. Homestar's panel really likes
to be power cycled. It's why the Linux driver for this panel has a
pm_runtime_put_sync_suspend() when the panel is being unprepared but
the normal panel-edp driver doesn't. It's also why this hardware has a
separate power rail for eDP vs. touchscreen, unlike all the other
trogdor boards. We won't start homestar's regulator on. While this
could mean a slight delay on homestar, it is probably a _correct_
delay. The bootloader might have left the regulator on (it does so in
dev and recovery modes), so if we turned the regulator off at probe
time and we actually hit the delay then we were probably violating T12
in the panel spec.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209091234.v3.3.I7050a61ba3a48e44b86053f265265b5e3c0cee31@changeid
In general, the timing diagrams for components specify a minimum time
for power cycling the component. When we remove power from a device we
need to let the device fully discharge and get to a quiescent state
before applying power again. If we power a device on too soon then it
might not have fully powered off and might be in a weird in-between /
invalid state.
eDP panels typically have a time that's at least 500 ms here. You can
see that in Linux's panel-edp driver nearly every device specifies a
"unprepare" time of at least 500 ms. This is a common minimum and the
500 ms is even in the example in the eDP spec.
In Linux, the "panel-edp" driver enforces this delay for its own
control of the regulator, but the "panel-edp" driver can't do anything
about other control of the regulator (for instance, by the touchpanel
driver).
Let's add 500 ms as a board constraint for the regulator that's used
for eDP/touchpanel on trogdor boards. If a given trogdor board stuffs
only panels that can use a shorter time or stuff some panels that need
a larger time then they can manually adjust this timing.
We'll only do this minimum delay for trogdor devices with eDP (ones
that use either bridge chip), not for devices with MIPI panels. MIPI
panels could have similar constraints but the 500 ms isn't necessarily
as standard and there are no known cases where this delay is needed.
For most trogdor boards, this doesn't actually seem to affect anything
when testing against shipping Linux. However, with pazqel360 it seems
that this does make a difference. It seems that the touchscreen on
this board _also_ needs some time for the regulator to discharge. That
time is much less than 500 ms, so we'll just put the eDP panel 500 ms
in there since the board constraint should be the "max" of the
components.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209091234.v3.2.I65ac577411b017eff50e7a4fda254e5583ccdc48@changeid
On at least one board (pazquel360) the reset line for the touchscreen
was scoped and found to take almost 2 ms to fall when we drove it
low. This wasn't great because the Linux driver for the touchscreen
(the elants_i2c driver) thinks it can do a 500 us reset pulse. If we
bump the drive strength to 8 mA then the reset line went down in ~421
us.
NOTE: we could apply this fix just for pazquel360, but:
* Probably other trogdor devices have similar timings and it's just
that nobody has noticed it before.
* There are other trogdor boards using the same elan driver that tries
to do 500 us reset pulses.
* Bumping the drive strength to 8mA across the board won't hurt. This
isn't a high speed signal or anything.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209091234.v3.1.I39c387f1e3176fcf340039ec12d54047de9f8526@changeid
Add a node describing the flash block found on pm6150l.
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209-fp4-pm6150l-flash-v1-2-531521eb2a72@fairphone.com
Just like in case of other SoCs change SDCC1/SDCC2 ops
to floor to avoid overclocking the controller.
Fixes: cbe63bfdc5 ("clk: qcom: Add Global Clock controller (GCC) driver for SM6115")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Iskren Chernev <me@iskren.info>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221209123910.178609-1-konrad.dybcio@linaro.org
Add an initial device tree for the Lenovo Tab P11. Currently it
enables:
- simplefb
- SD Card slot via SDHCI2
- gpio-keys & PON keys
- UFS
- RPM regulators
- USB2
This has been validated with a rev (62) device. You can check yours
next to the serial no. on the sticker in the lower portion of the
back side of your tablet.
To get a successful boot run:
cat arch/arm64/boot/Image.gz arch/arm64/boot/dts/qcom/\
sm6115p-lenovo-j606f.dtb > .Image.gz-dtb
~/mkbootimg/mkbootimg.py \
--kernel .Image.gz-dtb \
--ramdisk some/initrd.img \
--pagesize 4096 \
--base 0x0 \
--kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 \
--tags_offset 0x100 \
--cmdline 'SOME_CMDLINE' \
--dtb_offset 0x1f00000 \
--header_version 1 \
--os_version 11 \
--os_patch_level 2022-11 \
-o j606f.img
fastboot flash boot j606f.img
fastboot flash dtbo empty.img
fastboot flash recovery empty.img
fastboot reboot
Where empty.img is 2 zero-bytes.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221208201401.530555-5-konrad.dybcio@linaro.org
Document SM6115P, an APQ version of SM6115.
Document Lenovo Tab P11 (J606F) as a SM6115P device.
Add SM6115 to the msm-id list of shame.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221208201401.530555-4-konrad.dybcio@linaro.org
Since we have a functioning RPM clock driver, let's make use of it
and provide the real XO clock to clients, instead of the fixed-clock
stub.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221208201401.530555-3-konrad.dybcio@linaro.org
rpmcc used to rely on global clock lookup (and still does so for
backwards compat reasons) of "xo_board", which was common back
when we did not care about things like underscores in node names.
Nowadays it expects to be fed a reference to the fixed clock.
Satisfy that requirement to make sure rpm clock rates are not all
stuck at zero.
Fixes: 97e563bf5b ("arm64: dts: qcom: sm6115: Add basic soc dtsi")
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221208201401.530555-2-konrad.dybcio@linaro.org