[ Upstream commit c73729b64b ]
The function i40e_pf_wait_queues_disabled() iterates all PF's VSIs
up to 'pf->hw.func_caps.num_vsis' but this is incorrect because
the real number of VSIs can be up to 'pf->num_alloc_vsi' that
can be higher. Fix this loop.
Fixes: 69129dc39f ("i40e: Modify Tx disable wait flow in case of DCB reconfiguration")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73d9629e1c ]
Currently when PF administratively sets VF's MAC address and the VF
is put down (VF tries to delete all MACs) then the MAC is removed
from MAC filters and primary VF MAC is zeroed.
Do not allow untrusted VF to remove primary MAC when it was set
administratively by PF.
Reproducer:
1) Create VF
2) Set VF interface up
3) Administratively set the VF's MAC
4) Put VF interface down
[root@host ~]# echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
[root@host ~]# ip link set enp2s0f0v0 up
[root@host ~]# ip link set enp2s0f0 vf 0 mac fe:6c:b5:da:c7:7d
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether fe:6c:b5:da:c7:7d brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
[root@host ~]# ip link set enp2s0f0v0 down
[root@host ~]# ip link show enp2s0f0
23: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether 3c:ec:ef:b7:dd:04 brd ff:ff:ff:ff:ff:ff
vf 0 link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff, spoof checking on, link-state auto, trust off
Fixes: 700bbf6c1f ("i40e: allow VF to remove any MAC filter")
Fixes: ceb29474bb ("i40e: Add support for VF to specify its primary MAC address")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240208180335.1844996-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15faa1f67a ]
There is a crash when adding one of the lan966x interfaces under a lag
interface. The issue can be reproduced like this:
ip link add name bond0 type bond miimon 100 mode balance-xor
ip link set dev eth0 master bond0
The reason is because when adding a interface under the lag it would go
through all the ports and try to figure out which other ports are under
that lag interface. And the issue is that lan966x can have ports that are
NULL pointer as they are not probed. So then iterating over these ports
it would just crash as they are NULL pointers.
The fix consists in actually checking for NULL pointers before accessing
something from the ports. Like we do in other places.
Fixes: cabc9d4933 ("net: lan966x: Add lag support for lan966x")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240206123054.3052966-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9b0ed890ac ]
Do not report the XDP capability NETDEV_XDP_ACT_XSK_ZEROCOPY as the
bonding driver does not support XDP and AF_XDP in zero-copy mode even
if the real NIC drivers do.
Note that the driver used to report everything as supported before a
device was bonded. Instead of just masking out the zero-copy support
from this, have the driver report that no XDP feature is supported
until a real device is bonded. This seems to be more truthful as it is
the real drivers that decide what XDP features are supported.
Fixes: cb9e6e584d ("bonding: add xdp_features support")
Reported-by: Prashant Batra <prbatra.mail@gmail.com>
Link: https://lore.kernel.org/all/CAJ8uoz2ieZCopgqTvQ9ZY6xQgTbujmC6XkMTamhp68O-h_-rLg@mail.gmail.com/T/
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20240207084737.20890-1-magnus.karlsson@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65c6ee9045 ]
This is an error path and Smatch complains that "tbl_rev" is uninitialized
on this path. All the other functions follow this same patter where they
set the error code and goto out_free so that's probably what was intended
here as well.
Fixes: e8e10a37c5 ("iwlwifi: acpi: move ppag code from mvm to fw/acpi")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://msgid.link/09900c01-6540-4a32-9451-563da0029cb6@moroto.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c6ebb5b676 ]
This saves the error as PTR_ERR(wifi_pkg). The problem is that
"wifi_pkg" is a valid pointer, not an error pointer. Set the error code
to -EINVAL instead.
Fixes: 2a8084147b ("iwlwifi: acpi: support reading and storing WRDS revision 1 and 2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://msgid.link/9620bb77-2d7c-4d76-b255-ad824ebf8e35@moroto.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3012477cd5 ]
Before sending a SESSION PROTECTION cmd the driver checks if
the link_id indicated in the time event (and for which the cmd will be
sent) is valid and exists.
Clear the te_data::link_id when FW notifies that a session protection
ended, so the check will actually fail when it should.
Fixes: 1350658373 ("wifi: iwlwifi: support link_id in SESSION_PROTECTION cmd")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240204235836.c64a6b3606c2.I35cdc08e8a3be282563163690f8ca3edb51a3854@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1ce2654d87 upstream.
DDPP is copied from Synopsys Data book:
DDPP: Disable Data path Parity Protection.
When it is 0x0, Data path Parity Protection is enabled.
When it is 0x1, Data path Parity Protection is disabled.
The macro name should be XGMAC_DPP_DISABLE.
Fixes: 46eba193d0 ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20240203053133.1129236-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1692b9775e upstream.
The cited commit introduces and uses the string constants dpp_tx_err and
dpp_rx_err. These are assigned to constant fields of the array
dwxgmac3_error_desc.
It has been reported that on GCC 6 and 7.5.0 this results in warnings
such as:
.../dwxgmac2_core.c:836:20: error: initialiser element is not constant
{ true, "TDPES0", dpp_tx_err },
I have been able to reproduce this using: GCC 7.5.0, 8.4.0, 9.4.0 and 10.5.0.
But not GCC 13.2.0.
So it seems this effects older compilers but not newer ones.
As Jon points out in his report, the minimum compiler supported by
the kernel is GCC 5.1, so it does seem that this ought to be fixed.
It is not clear to me what combination of 'const', if any, would address
this problem. So this patch takes of using #defines for the string
constants
Compile tested only.
Fixes: 46eba193d0 ("net: stmmac: xgmac: fix handling of DPP safety error for DMA channels")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/netdev/c25eb595-8d91-40ea-9f52-efa15ebafdbc@nvidia.com/
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402081135.lAxxBXHk-lkp@intel.com/
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240208-xgmac-const-v1-1-e69a1eeabfc8@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b09b58e31b ]
When qmem_alloc and pfvf->hw_ops->sq_aq_init fails, sq->sg should be
freed to prevent memleak.
Fixes: c9c12d339d ("octeontx2-pf: Add support for PTP clock")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7f5fb33cf ]
For XDP_TX action xdp_buff is converted to xdp_frame. The conversion is
done by xdp_convert_buff_to_frame(). The memory type of the resulting
xdp_frame depends on the memory type of the xdp_buff. For page pool
based xdp_buff it produces xdp_frame with memory type
MEM_TYPE_PAGE_POOL. For zero copy XSK pool based xdp_buff it produces
xdp_frame with memory type MEM_TYPE_PAGE_ORDER0.
tsnep_xdp_xmit_back() is not prepared for that and uses always the page
pool buffer type TSNEP_TX_TYPE_XDP_TX. This leads to invalid mappings
and the transmission of undefined data.
Improve tsnep_xdp_xmit_back() to use the generic buffer type
TSNEP_TX_TYPE_XDP_NDO for zero copy XDP_TX.
Fixes: 3fc2333933 ("tsnep: Add XDP socket zero-copy RX support")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5bdda0048c ]
After commit e3eac9f32e ("wifi: cfg80211: Annotate struct
cfg80211_scan_request with __counted_by"), the compiler may enforce
dynamic array indexing of req->channels to stay below n_channels. As a
result, n_channels needs to be increased _before_ accessing the newly
added array index. Increment it first, then use "i" for the prior index.
Solves this warning in the coming GCC that has __counted_by support:
../drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function 'brcmf_internal_escan_add_info':
../drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:3783:46: warning: operation on 'req->
n_channels' may be undefined [-Wsequence-point]
3783 | req->channels[req->n_channels++] = chan;
| ~~~~~~~~~~~~~~~^~
Fixes: e3eac9f32e ("wifi: cfg80211: Annotate struct cfg80211_scan_request with __counted_by")
Cc: Arend van Spriel <aspriel@gmail.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Chi-hsien Lin <chi-hsien.lin@infineon.com>
Cc: Ian Lin <ian.lin@infineon.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Hector Martin <marcan@marcan.st>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240126223150.work.548-kees@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16867c38bc ]
Currently the driver exits eSR by calling
iwl_mvm_esr_mode_inactive() before updating the FW
(by deactivating one of the links), and therefore before
sending the EML frame notifying that we are no longer in eSR.
This is wrong for several reasons:
1. The driver sends SMPS activation frames when we are still in eSR
and SMPS should be disabled when in eSR
2. The driver restores RLC configuration as it was before eSR
entering, and RLC command shouldn't be sent in eSR
Fix this by calling iwl_mvm_esr_mode_inactive() after FW update
Fixes: 12bacfc2c0 ("wifi: iwlwifi: handle eSR transitions")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240201155157.d8d9dc277d4e.Ib5aee0fd05e35b1da7f18753eb3c8fa0a3f872f3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46eba193d0 ]
Commit 56e58d6c8a ("net: stmmac: Implement Safety Features in
XGMAC core") checks and reports safety errors, but leaves the
Data Path Parity Errors for each channel in DMA unhandled at all, lead to
a storm of interrupt.
Fix it by checking and clearing the DMA_DPP_Interrupt_Status register.
Fixes: 56e58d6c8a ("net: stmmac: Implement Safety Features in XGMAC core")
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a3ef39407 ]
The function to add an interface may be called without a previous
removal if the HW is being reconfigured. As such, only add the symlink
if the hardware is not being reconfigured due to a HW_RESTART.
Fixes: c36235acb3 ("wifi: iwlwifi: mvm: rework debugfs handling")
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.314395eacda4.I5823e962c3c3674b942383733debd10b3fe903e2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 486058f42a upstream.
As suggested by Paolo in link[1], if the memory allocation fails, the mm
layer will emit a lot warning comprising the backtrace, so remove the
print.
[1] https://lore.kernel.org/all/20231118081653.1481260-1-shaozhengchao@huawei.com/
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f0588b157f ]
In the arm random config file, kconfig option 'CONFIG_AEABI' is
disabled which results in adding the compiler flag '-mabi=apcs-gnu'.
This causes the compiler to add padding in virtchnl2_ptype
structure to align it to 8 bytes, resulting in the following
size check failure:
include/linux/build_bug.h:78:41: error: static assertion failed: "(6) == sizeof(struct virtchnl2_ptype)"
78 | #define __static_assert(expr, msg, ...) _Static_assert(expr, msg)
| ^~~~~~~~~~~~~~
include/linux/build_bug.h:77:34: note: in expansion of macro '__static_assert'
77 | #define static_assert(expr, ...) __static_assert(expr, ##__VA_ARGS__, #expr)
| ^~~~~~~~~~~~~~~
drivers/net/ethernet/intel/idpf/virtchnl2.h:26:9: note: in expansion of macro 'static_assert'
26 | static_assert((n) == sizeof(struct X))
| ^~~~~~~~~~~~~
drivers/net/ethernet/intel/idpf/virtchnl2.h:982:1: note: in expansion of macro 'VIRTCHNL2_CHECK_STRUCT_LEN'
982 | VIRTCHNL2_CHECK_STRUCT_LEN(6, virtchnl2_ptype);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Avoid the compiler padding by using "__packed" structure
attribute for the virtchnl2_ptype struct. Also align the
structure by using "__aligned(2)" for better code optimization.
Fixes: 0d7502a9b4 ("virtchnl: add virtchnl version 2 ops")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312220250.ufEm8doQ-lkp@intel.com
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240131222241.2087516-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04f647c8e4 ]
XDP queues are created/destroyed when a XDP program
is attached/detached. In current driver xdp_queues are not
getting destroyed on program exit due to incorrect xdp_queue
and tot_tx_queue count values.
This patch fixes the issue by setting tot_tx_queue and xdp_queue
count to correct values. It also fixes xdp.data_hard_start address.
Fixes: 06059a1a9a ("octeontx2-pf: Add XDP support to netdev PF")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20240130120610.16673-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc90fbe0c3 ]
Currently the teardown/setup flow for driver probe/remove is quite
a bit different from the reset flows in pdsc_fw_down()/pdsc_fw_up().
One key piece that's missing are the calls to pci_alloc_irq_vectors()
and pci_free_irq_vectors(). The pcie reset case is calling
pci_free_irq_vectors() on reset_prepare, but not calling the
corresponding pci_alloc_irq_vectors() on reset_done. This is causing
unexpected/unwanted interrupt behavior due to the adminq interrupt
being accidentally put into legacy interrupt mode. Also, the
pci_alloc_irq_vectors()/pci_free_irq_vectors() functions are being
called directly in probe/remove respectively.
Fix this inconsistency by making the following changes:
1. Always call pdsc_dev_init() in pdsc_setup(), which calls
pci_alloc_irq_vectors() and get rid of the now unused
pds_dev_reinit().
2. Always free/clear the pdsc->intr_info in pdsc_teardown()
since this structure will get re-alloced in pdsc_setup().
3. Move the calls of pci_free_irq_vectors() to pdsc_teardown()
since pci_alloc_irq_vectors() will always be called in
pdsc_setup()->pdsc_dev_init() for both the probe/remove and
reset flows.
4. Make sure to only create the debugfs "identity" entry when it
doesn't already exist, which it will in the reset case because
it's already been created in the initial call to pdsc_dev_init().
Fixes: ffa5585833 ("pds_core: implement pci reset handlers")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240129234035.69802-7-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e96094c1d1 ]
During reset the BARs might be accessed when they are
unmapped. This can cause unexpected issues, so fix it by
clearing the cached BAR values so they are not accessed
until they are re-mapped.
Also, make sure any places that can access the BARs
when they are NULL are prevented.
Fixes: 49ce92fbee ("pds_core: add FW update feature to devlink")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20240129234035.69802-6-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e82a8745b ]
There are multiple paths that can result in using the pdsc's
adminq.
[1] pdsc_adminq_isr and the resulting work from queue_work(),
i.e. pdsc_work_thread()->pdsc_process_adminq()
[2] pdsc_adminq_post()
When the device goes through reset via PCIe reset and/or
a fw_down/fw_up cycle due to bad PCIe state or bad device
state the adminq is destroyed and recreated.
A NULL pointer dereference can happen if [1] or [2] happens
after the adminq is already destroyed.
In order to fix this, add some further state checks and
implement reference counting for adminq uses. Reference
counting was used because multiple threads can attempt to
access the adminq at the same time via [1] or [2]. Additionally,
multiple clients (i.e. pds-vfio-pci) can be using [2]
at the same time.
The adminq_refcnt is initialized to 1 when the adminq has been
allocated and is ready to use. Users/clients of the adminq
(i.e. [1] and [2]) will increment the refcnt when they are using
the adminq. When the driver goes into a fw_down cycle it will
set the PDSC_S_FW_DEAD bit and then wait for the adminq_refcnt
to hit 1. Setting the PDSC_S_FW_DEAD before waiting will prevent
any further adminq_refcnt increments. Waiting for the
adminq_refcnt to hit 1 allows for any current users of the adminq
to finish before the driver frees the adminq. Once the
adminq_refcnt hits 1 the driver clears the refcnt to signify that
the adminq is deleted and cannot be used. On the fw_up cycle the
driver will once again initialize the adminq_refcnt to 1 allowing
the adminq to be used again.
Fixes: 01ba61b55b ("pds_core: Add adminq processing and commands")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20240129234035.69802-5-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 951705151e ]
The initial design for the adminq interrupt was done based
on client drivers having their own adminq and adminq
interrupt. So, each client driver's adminq isr would use
their specific adminqcq for the private data struct. For the
time being the design has changed to only use a single
adminq for all clients. So, instead use the struct pdsc for
the private data to simplify things a bit.
This also has the benefit of not dereferencing the adminqcq
to access the pdsc struct when the PDSC_S_STOPPING_DRIVER bit
is set and the adminqcq has actually been cleared/freed.
Fixes: 01ba61b55b ("pds_core: Add adminq processing and commands")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20240129234035.69802-4-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d321067e2c ]
There is a small window where pdsc_work_thread()
calls pdsc_process_adminq() and pdsc_process_adminq()
passes the PDSC_S_STOPPING_DRIVER check and starts
to process adminq/notifyq work and then the driver
starts a fw_down cycle. This could cause some
undefined behavior if the notifyqcq/adminqcq are
free'd while pdsc_process_adminq() is running. Use
cancel_work_sync() on the adminqcq's work struct
to make sure any pending work items are cancelled
and any in progress work items are completed.
Also, make sure to not call cancel_work_sync() if
the work item has not be initialized. Without this,
traces will happen in cases where a reset fails and
teardown is called again or if reset fails and the
driver is removed.
Fixes: 01ba61b55b ("pds_core: Add adminq processing and commands")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20240129234035.69802-3-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9407ff118 ]
The PCIe reset handlers can run at the same time as the
health thread. This can cause the health thread to
stomp on the PCIe reset. Fix this by preventing the
health thread from running while a PCIe reset is happening.
As part of this use timer_shutdown_sync() during reset and
remove to make sure the timer doesn't ever get rearmed.
Fixes: ffa5585833 ("pds_core: implement pci reset handlers")
Signed-off-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20240129234035.69802-2-brett.creeley@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c44fc98f0a ]
When working with GPIO, its direction must be set either when the GPIO is
requested by gpiod_get*() or later on by one of the gpiod_direction_*()
functions. Neither of this is done here which results in undefined
behavior on some systems.
As the reset GPIO is used right after it is requested here, it makes sense
to configure it as GPIOD_OUT_HIGH right away. With that, the following
gpiod_set_value_cansleep(1) becomes redundant and can be safely
removed.
Fixes: a653f2f538 ("net: dsa: qca8k: introduce reset via gpio feature")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1706266175-3408-1-git-send-email-michal.vokac@ysoft.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbc404d20d ]
All error handling paths, except this one, go to 'out' where
release_swfw_sync() is called.
This call balances the acquire_swfw_sync() call done at the beginning of
the function.
Branch to the error handling path in order to correctly release some
resources in case of error.
Fixes: ae14a1d8e1 ("ixgbe: Fix IOSF SB access issues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c1b4af8c1 ]
Currently ixgbe driver is notified of overheating events
via internal IXGBE_ERR_OVERTEMP error code.
Change the approach for handle_lasi() to use freshly introduced
is_overtemp function parameter which set when such event occurs.
Change check_overtemp() to bool and return true if overtemp
event occurs.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5795f533f3 ]
Change returning codes to the kernel ones instead of
the internal ones for the entire ixgbe driver.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: bbc404d20d ("ixgbe: Fix an error handling path in ixgbe_read_iosf_sb_reg_x550()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1f6a6b183 ]
The e1000e driver supports hardware with a variety of different clock
speeds, and thus a variety of different increment values used for
programming its PTP hardware clock.
The values currently programmed in e1000e_ptp_init are incorrect. In
particular, only two maximum adjustments are used: 24000000 - 1, and
600000000 - 1. These were originally intended to be used with the 96 MHz
clock and the 25 MHz clock.
Both of these values are actually slightly too high. For the 96 MHz clock,
the actual maximum value that can safely be programmed is 23,999,938. For
the 25 MHz clock, the maximum value is 599,999,904.
Worse, several devices use a 24 MHz clock or a 38.4 MHz clock. These parts
are incorrectly assigned one of either the 24million or 600million values.
For the 24 MHz clock, this is not a significant issue: its current
increment value can support an adjustment up to 7billion in the positive
direction. However, the 38.4 KHz clock uses an increment value which can
only support up to 230,769,157 before it starts overflowing.
To understand where these values come from, consider that frequency
adjustments have the form of:
new_incval = base_incval + (base_incval * adjustment) / (unit of adjustment)
The maximum adjustment is reported in terms of parts per billion:
new_incval = base_incval + (base_incval * adjustment) / 1 billion
The largest possible adjustment is thus given by the following:
max_incval = base_incval + (base_incval * max_adj) / 1 billion
Re-arranging to solve for max_adj:
max_adj = (max_incval - base_incval) * 1 billion / base_incval
We also need to ensure that negative adjustments cannot underflow. This can
be achieved simply by ensuring max_adj is always less than 1 billion.
Introduce new macros in e1000.h codifying the maximum adjustment in PPB for
each frequency given its associated increment values. Also clarify where
these values come from by commenting about the above equations.
Replace the switch statement in e1000e_ptp_init with one which mirrors the
increment value switch statement from e1000e_get_base_timinica. For each
device, assign the appropriate maximum adjustment based on its frequency.
Some parts can have one of two frequency modes as determined by
E1000_TSYNCRXCTL_SYSCFI.
Since the new flow directly matches the assignments in
e1000e_get_base_timinca, and uses well defined macro names, it is much
easier to verify that the resulting maximum adjustments are correct. It
also avoids difficult to parse construction such as the "hw->mac.type <
e1000_phc_lpt", and the use of fallthrough which was especially confusing
when combined with a conditional block.
Note that I believe the current increment value configuration used for
24MHz clocks is sub-par, as it leaves at least 3 extra bits available in
the INCVALUE register. However, fixing that requires more careful review of
the clock rate and associated values.
Reported-by: Trey Harrison <harrisondigitalmedia@gmail.com>
Fixes: 68fe1d5da5 ("e1000e: Add Support for 38.4MHZ frequency")
Fixes: d89777bf0e ("e1000e: add support for IEEE-1588 PTP")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62b4248105 ]
In case the interface between the MAC and the PHY is SGMII, then the bit
GIGA_MODE on the MAC side needs to be set regardless of the speed at
which it is running.
Fixes: d28d6d2e37 ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dfa988b4c7 ]
Setup PMCR port register for actual speed and duplex on internally
connected PHYs of the MT7988 built-in switch. This fixes links with
speeds other than 1000M.
Fixes: 110c18bfed ("net: dsa: mt7530: introduce driver for MT7988 built-in switch")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/a5b04dfa8256d8302f402545a51ac4c626fdba25.1706071272.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cae1f1c366 ]
Set DMA coherent mask to 32-bit which makes PPE offloading engine start
working on BPi-R4 which got 4 GiB of RAM.
Fixes: 2d75891ebc ("net: ethernet: mtk_eth_soc: support 36-bit DMA addressing on MT7988")
Suggested-by: Elad Yifee <eladwf@users.github.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/97e90925368b405f0974b9b15f1b7377c4a329ad.1706113251.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5343267110 ]
For a skb frag with a newly allocated copy page, the true size is
incorrectly set to packet buffer size. It should be set to PAGE_SIZE
instead.
Fixes: 82fd151d38 ("gve: Reduce alloc and copy costs in the GQ rx path")
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Link: https://lore.kernel.org/r/20240124161025.1819836-1-pkaligineedi@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3fe8d28c6 ]
Fix the warnings when building virtio_net driver.
"
drivers/net/virtio_net.c: In function ‘init_vqs’:
drivers/net/virtio_net.c:4551:48: warning: ‘%d’ directive writing between 1 and 11 bytes into a region of size 10 [-Wformat-overflow=]
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~
In function ‘virtnet_find_vqs’,
inlined from ‘init_vqs’ at drivers/net/virtio_net.c:4645:8:
drivers/net/virtio_net.c:4551:41: note: directive argument in the range [-2147483643, 65534]
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~~~~~~~~~
drivers/net/virtio_net.c:4551:17: note: ‘sprintf’ output between 8 and 18 bytes into a destination of size 16
4551 | sprintf(vi->rq[i].name, "input.%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/virtio_net.c: In function ‘init_vqs’:
drivers/net/virtio_net.c:4552:49: warning: ‘%d’ directive writing between 1 and 11 bytes into a region of size 9 [-Wformat-overflow=]
4552 | sprintf(vi->sq[i].name, "output.%d", i);
| ^~
In function ‘virtnet_find_vqs’,
inlined from ‘init_vqs’ at drivers/net/virtio_net.c:4645:8:
drivers/net/virtio_net.c:4552:41: note: directive argument in the range [-2147483643, 65534]
4552 | sprintf(vi->sq[i].name, "output.%d", i);
| ^~~~~~~~~~~
drivers/net/virtio_net.c:4552:17: note: ‘sprintf’ output between 9 and 19 bytes into a destination of size 16
4552 | sprintf(vi->sq[i].name, "output.%d", i);
"
Reviewed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Link: https://lore.kernel.org/r/20240104020902.2753599-1-yanjun.zhu@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68e1010cda ]
of_get_child_by_name() gives us an OF node with an elevated refcount,
which should be dropped when we're done with it. This is so that,
if (of_node_check_flag(node, OF_DYNAMIC)) is true, the node's memory can
eventually be freed.
There are 2 distinct paths to be considered in qca8k_mdio_register():
- devm_of_mdiobus_register() succeeds: since commit 3b73a7b8ec ("net:
mdio_bus: add refcounting for fwnodes to mdiobus"), the MDIO core
treats this well.
- devm_of_mdiobus_register() or anything up to that point fails: it is
the duty of the qca8k driver to release the OF node.
This change addresses the second case by making sure that the OF node
reference is not leaked.
The "mdio" node may be NULL, but of_node_put(NULL) is safe.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ebb1f95e0 ]
As of today, the last MCAM entry was not getting allocated because of
a <= check with the max_bmap count. This patch modifies that and if the
requested entry is greater than the available entries then set it to the
max value.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20240101145042.419697-1-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31deb12e85 ]
Currently, if a VF is disabled using the
'ip link set dev $ETHX vf $VF_NUM state disable' command, the VF is still
able to receive traffic.
Fix the behavior of the 'ip link set dev $ETHX vf $VF_NUM state disable'
to completely shutdown the VF's queues making it entirely disabled and
not able to receive or send any traffic.
Modify the behavior of the 'ip link set $ETHX vf $VF_NUM state enable'
command to make a VF do reinitialization bringing the queues back up.
Co-developed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c16618bc0 ]
Using calculate_bit_shift() to replace rtl8723_phy_calculate_bit_shift().
And fix an undefined bitwise shift behavior problem.
Signed-off-by: Su Hui <suhui@nfschina.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231219065739.1895666-12-suhui@nfschina.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit acc55d7dd4 ]
The Wi-Fi firmware 29.29.X should use version 2 role info format. FDDT
mechanism version 5 use the same cell members to judge traffic situation,
don't need to add another new format.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231218061341.51255-2-pkshih@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7173be21ae ]
While converting to FIELD_PREP() and FIELD_GET(), it was noticed that
some of the RSS defines had *included* the shift in their definitions.
This is completely outside of normal, such that a developer could easily
make a mistake and shift at the usage site (like when using
FIELD_PREP()).
Rename the defines and set them to the "pre-shifted values" so they
match the template the driver normally uses for masks and the member
bits of the mask, which also allows the driver to use FIELD_PREP
correctly with these values. Use GENMASK() for this changed MASK value.
Do the same for the VLAN EMODE defines as well.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3314f2097d ]
This series is introducing the use of FIELD_GET and FIELD_PREP which
requires bitfield.h to be included. Fix all the includes in this one
change, and rearrange includes into alphabetical order to ease
readability and future maintenance.
virtchnl.h and it's usage was modified to have it's own includes as it
should. This required including bits.h for virtchnl.h.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc82a08ae7 ]
mv88e6xxx_get_stats, which collects stats from various sources,
expects all callees to return the number of stats read. If an error
occurs, 0 should be returned.
Prevent future mishaps of this kind by updating the return type to
reflect this contract.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3cb7a830a ]
Driver has a logic leak in ring data allocation/free,
where aq_ring_free could be called multiple times on same ring,
if system is under stress and got memory allocation error.
Ring pointer was used as an indicator of failure, but this is
not correct since only ring data is allocated/deallocated.
Ring itself is an array member.
Changing ring allocation functions to return error code directly.
This simplifies error handling and eliminates aq_ring_free
on higher layer.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Link: https://lore.kernel.org/r/20231213095044.23146-1-irusskikh@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
