If a mode set fails we may get a message from drm_crtc_helper if we're lucky,
but it won't tell us anything about *why* we failed to set a mode. So
add a few DRM_ERRORs for the cases that shouldn't happen so we can debug
things more easily.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Mainly for use in debugging and benchmarking, this file allows the user
to control the max frequency used by the GPU. Frequency may still vary
based on workload (if the frequency is set to higher than the minimum)
but won't go over the newly set value.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
The Dell OptiPlex FX170 claims to have LVDS, but doesn't.
Signed-off-by: Pieterjan Camerlynck <pieterjan.camerlynck@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Failing to pin a scanout buffer will most likely lead to a black
screen, so if the GPU is wedged, then just let the pin happen and hope
that things work out OK.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
There is no need to use dynamic initializaion, it just confuses the reader.
Switch to static initializers like its used in other files.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
[v2: Rebased on v3.0]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
On Ironlake and above, we have per-transcoder DIP registers, so use them
for sending DIPs like AVI infoframes on ILK and above.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
On a recent compile, I got this warning:
CC [M] drivers/net/pcmcia/smc91c92_cs.o
drivers/net/pcmcia/smc91c92_cs.c: In function ‘smc91c92_probe’:
drivers/net/pcmcia/smc91c92_cs.c:812:12: warning: ‘j’ may be used uninitialized in this function
However, "j" is only used in a branch which has the same condition as
a previous branch, where j is set, e.g.
int j;
if (CONDITION)
j = VALUE
...
if (CONDITION)
printk(j)
Still, avoid this warning, as it is easy to circumvent.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01"
as the third product ID. Those have Agere firmware.
With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be
assumed to have Intersil firmware. Cards with Agere firmware use
"Version 01.01".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Kill off the buff gpio as not used anywhere.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Now the are optional, let us get rid of the ones that don't have
any content.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
10 boards define these empty, probably indicating not everyone has a use for them.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: warning: function declaration isn't a prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/ov5642.c:985:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:985:1: warning: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/media/video/ov5642.c:985:1: warning: parameter names (without types) in function declaration
drivers/media/video/ov5642.c: In function 'ov5642_mod_init':
drivers/media/video/ov5642.c:998:9: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/media/video/ov5642.c:998:9: note: each undeclared identifier is reported only once for each function it appears in
drivers/media/video/ov5642.c: At top level:
drivers/media/video/ov5642.c:1009:20: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1009:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1009:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/media/video/ov5642.c:1009:20: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c:1010:15: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1010:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1010:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/media/video/ov5642.c:1010:15: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c:1011:16: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1011:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1011:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/media/video/ov5642.c:1011:16: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c: In function 'ov5642_mod_init':
drivers/media/video/ov5642.c:999:1: warning: control reaches end of non-void function
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only Sparc and PPC actually have the asm/prom.h include and as such they
can't be moved outside of the ifdefs.
Reported-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Several vendors implement a second configuration register, which we
check during device detection. Refactor the code to avoid duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
With a device ID register value of 0, the SA56004 detection is rather
weak. Check several other register too to confirm the detection, as we
do for other supported devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The optional extended local temperature register can never have
address 0, as this address is already used by another register. Thus
we can get rid of flag LM90_HAVE_LOCAL_EXT and simply rely on
reg_local_ext being non-zero to determine if a given chip has this
extension or not. This makes the code more simple.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
proc_fork_connector() uses ->real_parent lockless. This is not safe if
copy_process() was called with CLONE_THREAD or CLONE_PARENT, in this case
the parent != current can go away at any moment.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The D-Link DGE-530T rev C1 is a re-badged Realtek 8169 named DLG10028C,
unlike the previous revisions which were skge based. It is probably
the same as the discontinued DGE-528T (0x4300) other than the PCI ID.
The PCI ID is 0x1186:0x4302.
Adding it to r8169.c where 0x1186:0x4300 is already found makes the card
be detected and work.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=38862
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=34552
Signed-off-by: Klement Fish <klement2@azet.sk>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Most PMBus devices provide manufacturer specific commands to read low and/or
high peak values for some or all of its sensors.
To support providing those values as lowest/highest attributes to the user,
introduce virtual PMBus commands. Those commands reside outside the normal
command set and have to be implemented in device specific code, which map the
virtual commands to device specific commands.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
With virtual register page support, it is now possible that the status register
on virtual pages does not exist or is itself virtual. To take this into account
when creating alarm attributes, generate those attributes only if the status
register on the respective page is known to exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus chips have non-standard sensor registers. An easy way to
support such sensors is to introduce virtual pages and map the non-standard
registers into standard registers on an extra page.
For this to work, the code verifying if the configured number of pages exists
has to be removed. Since a wrong number of pages can only be configured in a
front-end driver, this should not have a practical impact since the resulting
errors should be found during development and testing.
Also, functions to read the chip status while checking if a command register
exists must be modified to no longer set the page register before reading the
status, since the physical page associated with the checked register may not
exist. This does not make a functional difference since the page was already set
when the attempt to read the register was made.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus devices use non-standard registers for some of the sensors and/or
limits. To support such devices, add code to support reading and writing of word
size registers in device specific code.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
CB tuning is needed to handle potential process variations that might
cause clock jitter for certain PLL settings. However, we were setting
it incorrectly since we were using the wrong M value as a check (M1 when
we needed to use the whole M value). Fix it up, making my HDMI
attached display a little prettier (used to have occasional dots crawl
across the display).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Writes to the plane control register are buffered in the chip until a
write to the DSPADDR (pre-965) or DSPSURF (post-965) register occurs.
This patch adds flushes in:
intel_enable_plane
gen6_init_clock_gating
ivybridge_init_clock_gating
Signed-off-by: Keith Packard <keithp@keithp.com>
After writing to the plane control reg we need to write to the surface
reg to trigger the double buffered register latch. On previous
chipsets, writing to DSPADDR was enough, but on ILK+ DSPSURF is the reg
that triggers the double buffer latch.
v2: write DSPADDR too to cover pre-965 chipsets
v3: use flush_display_plane instead, that's what it's for
v4: send the right patch
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
On CougarPoint and PantherPoint PCH chips, the timing generator may fail
to start after DP training completes. This is due to a bug in the
FDI autotraining detect logic (which will stall the timing generator and
re-enable it once training completes), so disable it to avoid silent DP
mode setting failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
This corrects the DPMS mode tracking so that the DPMS code will
actually turn the CRTC off the next time the screen saves.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 885a50147f.
We actually *do* need to track DPMS state so that on hotplug, we don't
retrain the link until DPMS is disabled.
However, that code had avery small bug -- it wouldn't set the
dpms_mode at mode set time, and so link retraining would not actually
occur on monitor hotplug until the monitor had gone through a DPMS
off/DPMS on cycle.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
Display port pipe selection on CPT is not done with a bit in the
output register, rather it is controlled by a couple of bits in the
separate transcoder register which indicate which display port output
is connected to the transcoder.
This patch replaces the simplistic macro DP_PIPE_ENABLED with the
rather more complicated function dp_pipe_enabled which checks the
output register to see if that is enabled, and then goes on to either
check the output register pipe selection bit (on non-CPT) or the
transcoder DP selection bits (on CPT).
Before this patch, any time the mode of pipe A was changed, any
display port outputs on pipe B would get disabled as
intel_disable_pch_ports would ensure that the mode setting operation
could occur on pipe A without interference from other outputs
connected to that pch port
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Eliminates an open-coded read and also gains the retry behaviour of
intel_dp_get_dpcd, which seems like a good idea.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
This describes the function better, allowing it to be used where the
DPCD value is relevant.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
This uses the common dpcd reading routine, i915_dp_detect_common,
instead of open-coding a call to intel_dp_aux_native_read. Besides
reducing duplicated code, this also gains the read retries which
may be necessary when a cable is first plugged back in and the link
needs to be retrained.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
drm_helper_hpd_irq_event queues another work proc to go and deliver
the user-space event, and that function also wants to hold the config
mutex, so we shouldn't hold the mutex across the
drm_helper_hpd_irq_event call.
Signed-off-by: Keith Packard <keithp@keithp.com>
Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.
This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Since 43cc71eed1 (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
This patch changes the MODULE_ALIAS to "platform:ab8500-gpio".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow GPIO drivers to use of_gpio_simple_xlate. This is useful for the
generic GPIO driver for example where gpio_chip is embedded in
bgpio_chip and doesn't need of_mm_gpio_chip but has a simple 1:1 GPIO
mapping.
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The logic at em28xx_isoc_dvb_max_packetsize() sucks, at least for newer
the needed packet size. Yet, it is better than nothing.
Rewrite the code in order to change the default to 752 for em2884 and
newer chips and provide a better way to handle per-chipset specifics.
For em2874, the current default should be enough, as the only em2874
board is currently a 1-seg ISDB-T board, so, it needs only a limited
amount of bandwidth.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the driver assumes that all QAM carriers are spaced with
8MHz. This is wrong, and may decrease QoS on Countries like Brazil,
that have DVB-C carriers with 6MHz-spaced.
Fortunately, both ITU-T J-83 and EN 300 429 specifies a way to
associate the symbol rate with the bandwidth needed for it.
For ITU-T J-83 2007 annex A, the maximum symbol rate for 6 MHz is:
6 MHz / 1.15 = 5217391 Bauds
For ITU-T J-83 2007 annex C, the maximum symbol rate for 6 MHz is:
6 MHz / 1.13 = 5309735 Bauds.
As this tuner is currently used only for DRX-K, and it is currently
hard-coded to annex A, I've opted to use the roll-off factor of 0.15,
instead of 0.13.
If we ever support annex C, the better would be to add a DVB S2API
call to allow changing between Annex A and C, and add the 0.13 roll-off
factor to it.
This code is currently being used on other frontends, so I think we
should later add a core function with this code, to warrant that
it will be properly implemented everywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
