Beacon transmission is now handled through a slot mechanism.
This allows multiple beaconing interfaces to be be present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Match the beacon header with that of the firmware.
Also, the firmware reports the TSF for an SWBA, so
store it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, update the wiphy information and use the correct
device pointer when registering. This would fix ethtool.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the new FW requires backward incompatible host driver changes,
rename the FW to allow older driver versions to work with the
older FW.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the AR7010 devices supoprted by ath9k_htc are based
on version v1.1, so remove support for v1.0.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, ampdu stream is created on the first qos packet to an
HT sta. The overhead of setting up the BA session may not be
justified if the outgoing packet rate is minimal (e.g., ping). So
we only allow ampdu streams after seeing a critical number of
packets in an arbitrary one-second interval.
Based on work by Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently ath9k only available in menuconfig if PCI bus
support is enabled. However the driver is required for
the built-in wireless MACs of the Atheros AR9130/AR9132
SoCs. These SoCs have no PCI controller, the wireless
MAC is connected to the AHB bus on them.
Introduce separated config options for the supported
buses, in order to allow building of ath9h without PCI
bus support.
As a bonus, this patch removes the cross-reference of
the ATHEROS_AR71XX option which is not present in the
kernel.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not need to enable all the interrupts in mwl8k_probe_hw.
We need to enable only MWL8K_A2H_INT_OPC_DONE interrupt for sending
commands to the firmware. Keep the other interrupts masked in
mwl8k_probe_hw. Also, in mwl8k_start, where we expect other interrupts,
enable only those interrupts we are interested in.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was done to handle a number of conflicts, the majority of which
were caused by the big "fix spelling issues" patch.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
priv->tx_power_next is not initialized to max supported power,
but instead default value is used, what cause errors like
[ 58.597834] iwl3945 0000:03:00.0: Requested user TXPOWER 15 above upper limit 14.
[ 58.597839] iwl3945 0000:03:00.0: Error setting Tx power (-22).
if maximum tx power read from the eeprom is smaller than default.
In consequence card is unable to initialize properly. Fix the problem
and cleanup tx power initialization.
Reported-and-tested-by: Robin Dong <hao.bigrat@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Machines are getting deadlock in four node cluster environment.
All nodes are accessing (find /gfs2 -depth -print|cpio -ocv > /dev/null)
200 GB storage on a GFS2 filesystem.
This result in memory fragmentation and driver receives 18 frags for
1448 byte packets.
For non tso packet, fw drops the tx request, if it has >14 frags.
Fixing it by pulling extra frags.
Cc: stable@kernel.org
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 74888760d4
"dt/net: Eliminate users of of_platform_{,un}register_driver"
broke building mscan driver. Fix it.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using uninitialised watermarks values for disabled pipes which
were combined into a single WM register and so corrupting the values for
the enabled pipe and upsetting the display hardware.
Reported-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (22 commits)
Revert "i915: restore only the mode of this driver on lastclose"
Revert "ttm: Utilize the DMA API for pages that have TTM_PAGE_FLAG_DMA32 set."
i915: select VIDEO_OUTPUT_CONTROL for ACPI_VIDEO
drm/radeon/kms: properly program vddci on evergreen+
drm/radeon/kms: add voltage type to atom set voltage function
drm/radeon/kms: fix pcie_p callbacks on btc and cayman
drm/radeon/kms: fix suspend on rv530 asics
drm/radeon/kms: clean up gart dummy page handling
drm/radeon/kms: make radeon i2c put/get bytes less noisy
drm/radeon/kms: pll tweaks for rv6xx
drm/radeon: Fix KMS legacy backlight support if CONFIG_BACKLIGHT_CLASS_DEVICE=m.
radeon: Fix KMS CP writeback on big endian machines.
i915: restore only the mode of this driver on lastclose
drm/nvc0: improve vm flush function
drm/nv50-nvc0: remove some code that doesn't belong here
drm/nv50: use "nv86" tlb flush method on everything except 0x50/0xac
drm/nouveau: quirk for XFX GT-240X-YA
drm/nv50-nvc0: work around an evo channel hang that some people see
drm/nouveau: implement init table opcode 0x5c
drm/nouveau: fix oops on unload with disabled LVDS panel
...
The SD8787 firmware image is shared with mwifiex driver.
Whoever gets loaded first will be responsible for firmware
downloading.
Signed-off-by: Kevin Gan <ganhy@marvell.com>
Signed-off-by: Tristan Xu <xurf@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Check the return value of hu->proto->recv() in hci_uart_tty_receive()
the recv() may return error, check it, not add this to statistics.
Signed-off-by: Jiejing Zhang <jiejing.zhang@freescale.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When the crop rectangle needs to be modified to match hardware
requirements, center the resulting rectangle on the requested rectangle
instead of removing pixels from the right and bottom sides only.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit
379fa5d ([media] V4L: mx3_camera: convert to videobuf2)
mx3_camera uses videobuf2, but that commit didn't upgrade the select
resulting in the following build failure:
drivers/built-in.o: In function `mx3_camera_init_videobuf':
clkdev.c:(.text+0x86580): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `mx3_camera_probe':
clkdev.c:(.devinit.text+0x3548): undefined reference to `vb2_dma_contig_init_ctx'
clkdev.c:(.devinit.text+0x3578): undefined reference to `vb2_dma_contig_cleanup_ctx'
drivers/built-in.o: In function `mx3_camera_remove':
clkdev.c:(.devexit.text+0x674): undefined reference to `vb2_dma_contig_cleanup_ctx'
make[2]: *** [.tmp_vmlinux1] Error 1
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the camera host driver (sh_mobile_ceu_camera.c) is unloaded and then
reloaded, probe will fail, because camera client .set_bus_param() and
.query_bus_param() methods have been set to NULL. Fix this by caching
the original pointers and restoring them on driver-unbind.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i2c_unregister_device() frees the I2C client, so, dereferencing it
afterwards is a bug, that leads to Oopses.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the introduction of CSI2 support on sh-mobile, the host driver
switched to using v4l2_device_call_until_err() with grp_id == 0 to
call subdev operations on the sensor and the CSI2 subdev. However,
this has broken multi-client set ups like the one on migor, because
that way all operations get called on both clients. To fix this add
a grp_id and set it to the client private context.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
buf->size is not yet initialised in videobuf2-dma-contig at the time of
the error message, use "size."
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The videobuf2-dma-contig allocator returns an ERR_PTR() on failure, not
a NULL like all other allocators. Fix videobuf2-core to also correctly
recognise those failures.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Comment the use of local variables to reduce the number of load/store
operations on uncached memory, in hopes of not losing this optimization
accidentally in the future.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If allocating stream buffers for one of the primary streams (e.g. YUV)
failed during card probe, the error path clean up would try to manipulate
the yet unitialized IDX stream structures. This caused a BUG due to
unitialized list heads.
Detect that case and ignore the uninitialized IDX stream.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a partial revert of 6eab04a876 ("treewide: remove extra
semicolons"). Wireless tree removes the code in question, so
drop the hunk to avoid conflict.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
DMA mode 1 data corruption anomaly on Blackfin systems. This issue is
specific to the Blackfin silicon as the bug appears to be related to the
connection of the musb ip to the bus/dma fabric.
Data corruption when using USB DMA mode 1. (Issue manager 17-01-0105)
DMA mode 1 allows large size transfers to generate a single interrupt
at the end of the entire transfer. The transfer is split up in packets
of length specified in the Maximum Packet Size field for that endpoint.
If the transfer size is not an integer multiple of the Maximum Packet
Size, a short packet will be present at the end of the transfer.
Under certain conditions this packet may be corrupted in the USB FIFO.
Workaround:
Use DMA mode 1 to transfer (n* Maximum Packet Size) and schedule DMA
mode 0 to transfer the short packet.
As an example if your transfer size is 33168 bytes and Maximum Packet
Size equals 512, schedule [33168 - (33168 mod 512)] in DMA mode 1 and
the remainder (33168 mod 512) in DMA mode 0.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We are now using our own list_head, so we should
be checking against that, not the gadget driver's
list_head.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Due to the recent changes to musb's glue layers,
we can't compile musb-hdrc as a module - compilation
will break due to undefined symbol musb_debug. In
order to fix that, we need a big re-work of the
debug support on the MUSB driver.
Because that would mean a lot of new code coming
into the -rc series, it's best to defer that to
next merge window and for now just disable module
support for MUSB.
Once we get the refactor of the debugging support
done, we can simply revert this patch and things
will go back to normal again.
Cc: stable@kernel.org # v2.6.38
Signed-off-by: Felipe Balbi <balbi@ti.com>
"tx_ram" points to io memory. We can't dereference it directly. Sparse
complains about this: "drivers/usb/musb/cppi_dma.c:1205:25: warning:
dereference of noderef expression"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Gcc gives the following warnings:
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_tx_segment’:
drivers/usb/musb/cppi_dma.c:600: warning: format ‘%x’ expects type ‘unsigned int’, but argument 8 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_next_rx_segment’:
drivers/usb/musb/cppi_dma.c:822: warning: format ‘%x’ expects type ‘unsigned int’, but argument 9 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c: In function ‘cppi_rx_scan’:
drivers/usb/musb/cppi_dma.c:1042: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 4 has type ‘dma_addr_t’
drivers/usb/musb/cppi_dma.c:1114: warning: format ‘%08x’ expects type ‘unsigned int’, but argument 7 has type ‘dma_addr_t’
dma_addr_t is sometimes 32 bit and sometimes 64. We normally cast them
to unsigned long long for printk().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On the completion of tx dma, dma is disabled by clearing MUSB_TXCSR_DMAENAB in
TXCSR. If MUSB_TXCSR_AUTOSET was set in txstate() it will remain set although
it is not needed in PIO mode. Clear it as soon as it is not needed.
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a new EV_SYN code, SYN_DROPPED, to inform the client when input
events have been dropped from the evdev input buffer due to a
buffer overrun. The client should use this event as a hint to
reset its state or ignore all following events until the next
packet begins.
Signed-off-by: Jeff Brown <jeffbrown@android.com>
[dtor@mail.ru: Implement Henrik's suggestion and drop old events in
case of overflow.]
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Atmel touchscreen chips can use MT protocol B because they can assign
unique id to ABS_MT_TRACKING_ID from finger id provided by hardware.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Make the CHG line (interrupt line) go high after the interrupts have been
enabled to make sure we don't miss the falling edge.
Signed-off-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Atmel touchscreen chip can support 12bit resolution and this patch
modifies to get maximum x and y size from platform data.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Iiro Valkonen <iiro.valkonen@atmel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This fixes the failure to register the IRQ_RTCAlrm alarm as a wakeup
event. It is misinterpreted as a gpio irq not a PWER bitmask. Fixed
this by converting the incorrect IRQ_TO_IRQ() to a correct version of
irq_to_gpio().
Reported-by: Nick Bane <nickbane1@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
