TI shared transport driver previously intended to expose rfkill
entries for each of the protocol gpio that the chip would have.
However now in case such gpios exist, which requires to be enabled
for a specific protocol, the responsibility lay on protocol driver.
This patch removes the request/free of multiple gpios, rfkill struct
references and also removes the chip_toggle function.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Where file-transfer stops/pauses in between, is
result of a HCI-LL anamoly in ST LL driver.
ST LL did not copy the contents of WaitQ into the TxQ, when a WAKEUP_IND
collision happened.
Make also sure, that the copying mechanism is safe, by wrapping it around
spin locks inside st_int_recv().
This was easily reproduced when the sleep timeout was reduced to 100ms
for HCI-LL.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To fasten the process of firmware download, the chip allows
disabling of the command complete event generation from host.
In these cases, only few very essential commands would have
the command complete events and hence the wait associated with
them.
So now the driver would wait for a command complete event, only
when it comes across a wait event during firmware parsing.
This would also mean we need to skip not just the change baud
rate command but also the wait for it.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pr_debug-ing few pr_infos from the data paths such as tty receive and
write so as to reduce debugs when we have higher logging levels enabled
undef VERBOSE in receive to avoid huge logs when log level 8 is set.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
set-right the error codes that the shared transport driver
returns.
Instead of magic numbers like -1, return relevant codes such as
ETIMEDOUT or EIO, EAGAIN when wait times out or uart write bytes don't
match expected value or when registration fails and needs to be
attempted again.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The communication between ST KIM and UIM was interfaced
over the /dev/rfkill device node.
Move the interface to a simpler less abusive sysfs entry
mechanism and document it in Documentation/ABI/testing/
under sysfs-platform-kim.
Shared transport driver would now read the UART details
originally received by bootloader or firmware as platform
data.
The data read will be shared over sysfs entries for the user-space
UIM or other n/w manager/plugins to be read, and assist the driver
by opening up the UART, setting the baud-rate and installing the
line discipline.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The architecture of shared transport had begun with individual
protocols like bluetooth, fm and gps telling the shared transport
what sort of protocol they are and then expecting the ST driver
to parse the incoming data from chip and forward data only
relevant to the protocol drivers.
This change would mean each protocol drivers would also send
information to ST driver as to how to intrepret their protocol
data coming out of the chip.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the N8 to the list of devices in cdc-acm, in order to get the
secondary ACM device exposed.
In the spirit of:
http://kerneltrap.org/mailarchive/linux-usb/2010/9/4/6264554
Signed-off-by: Arvid Ephraim Picciani <arvid.picciani@nokia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying to compile drivers/usb/gadget/f_mass_storage.o currently fails and
spews a ton of warnings :
CC drivers/usb/gadget/f_mass_storage.o
drivers/usb/gadget/f_mass_storage.c:436:22: error: field ‘function’ has incomplete type
drivers/usb/gadget/f_mass_storage.c: In function ‘fsg_from_func’:
drivers/usb/gadget/f_mass_storage.c:466:9: warning: type defaults to ‘int’ in declaration of ‘__mptr’
drivers/usb/gadget/f_mass_storage.c:466:9: warning: initialization from incompatible pointer type
drivers/usb/gadget/f_mass_storage.c: At top level:
drivers/usb/gadget/f_mass_storage.c:2743:15: warning: ‘struct usb_composite_dev’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c:2743:15: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/usb/gadget/f_mass_storage.c: In function ‘fsg_common_init’:
drivers/usb/gadget/f_mass_storage.c:2745:34: error: dereferencing pointer to incomplete type
drivers/usb/gadget/f_mass_storage.c:2775:23: error: dereferencing pointer to incomplete type
drivers/usb/gadget/f_mass_storage.c:2779:3: error: implicit declaration of function ‘usb_string_id’
drivers/usb/gadget/f_mass_storage.c: At top level:
drivers/usb/gadget/f_mass_storage.c:2984:60: warning: ‘struct usb_configuration’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c:3003:57: warning: ‘struct usb_configuration’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c: In function ‘fsg_bind’:
drivers/usb/gadget/f_mass_storage.c:3006:31: error: dereferencing pointer to incomplete type
drivers/usb/gadget/f_mass_storage.c:3013:2: error: implicit declaration of function ‘usb_interface_id’
drivers/usb/gadget/f_mass_storage.c:3033:3: error: dereferencing pointer to incomplete type
drivers/usb/gadget/f_mass_storage.c:3034:6: error: dereferencing pointer to incomplete type
drivers/usb/gadget/f_mass_storage.c:3043:4: error: dereferencing pointer to incomplete type
drivers/usb/gadget/f_mass_storage.c:3044:7: error: dereferencing pointer to incomplete type
drivers/usb/gadget/f_mass_storage.c:3045:26: error: dereferencing pointer to incomplete type
drivers/usb/gadget/f_mass_storage.c: At top level:
drivers/usb/gadget/f_mass_storage.c:3067:14: warning: ‘struct usb_configuration’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c:3067:14: warning: ‘struct usb_composite_dev’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c: In function ‘fsg_bind_config’:
drivers/usb/gadget/f_mass_storage.c:3093:2: error: implicit declaration of function ‘usb_add_function’
drivers/usb/gadget/f_mass_storage.c: At top level:
drivers/usb/gadget/f_mass_storage.c:3103:9: warning: ‘struct usb_configuration’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c:3103:9: warning: ‘struct usb_composite_dev’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c: In function ‘fsg_add’:
drivers/usb/gadget/f_mass_storage.c:3105:2: warning: passing argument 1 of ‘fsg_bind_config’ from incompatible pointer type
drivers/usb/gadget/f_mass_storage.c:3065:12: note: expected ‘struct usb_composite_dev *’ but argument is of type ‘struct usb_composite_dev *’
drivers/usb/gadget/f_mass_storage.c:3105:2: warning: passing argument 2 of ‘fsg_bind_config’ from incompatible pointer type
drivers/usb/gadget/f_mass_storage.c:3065:12: note: expected ‘struct usb_configuration *’ but argument is of type ‘struct usb_configuration *’
drivers/usb/gadget/f_mass_storage.c: At top level:
drivers/usb/gadget/f_mass_storage.c:3190:23: warning: ‘struct usb_composite_dev’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c:3195:23: warning: ‘struct usb_composite_dev’ declared inside parameter list
drivers/usb/gadget/f_mass_storage.c:3193:1: error: conflicting types for ‘fsg_common_from_params’
drivers/usb/gadget/f_mass_storage.c:3188:1: note: previous declaration of ‘fsg_common_from_params’ was here
drivers/usb/gadget/f_mass_storage.c: In function ‘fsg_common_from_params’:
drivers/usb/gadget/f_mass_storage.c:3199:2: warning: passing argument 2 of ‘fsg_common_init’ from incompatible pointer type
drivers/usb/gadget/f_mass_storage.c:2741:27: note: expected ‘struct usb_composite_dev *’ but argument is of type ‘struct usb_composite_dev *’
make[1]: *** [drivers/usb/gadget/f_mass_storage.o] Error 1
make: *** [drivers/usb/gadget/f_mass_storage.o] Error 2
This is due to the missing include of linux/usb/composite.h - this patch
adds the missing include.
In addition there's also a problem in fsg_common_init() where we memset
'common', but we use the size of a pointer to 'struct fsg_common' as the
size argument to memset(), not the actual size of the struct. This patch
fixes the sizeof so we zero the entire struct as intended.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the below compilation errors.
CC drivers/usb/gadget/ci13xxx_msm.o
CC net/mac80211/led.o
drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event':
drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function)
drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once
drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.)
drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function)
make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1
make[3]: *** [drivers/usb/gadget] Error 2
MSM USB driver is not supported on boards like trout (MSM7201) which
has an external PHY.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some UDC drivers fails to queue a request if req->buf == NULL even for
ZLP requests. This patch adds a poisoned pointer instead of NULL to
make the code compliant with the gadget specification and catches
possible bug in the UDC driver if it tries to dereference buffer pointer
on ZLP request.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide optional hooks for the host controller driver to override the
default DMA mapping and unmapping routines. In general, these shouldn't
be necessary unless the host controller has special DMA requirements,
such as alignment contraints. If these are not specified, the
general usb_hcd_(un)?map_urb_for_dma functions will be used instead.
Also, pass the status to unmap_urb_for_dma so it can know whether the
DMA buffer has been overwritten.
Finally, add a flag to be used by these implementations if they
allocated a temporary buffer so it can be freed properly when unmapping.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The convention is to prefix symbols exported from the USB HCD core with
"usb_hcd". This change makes unmap_urb_setup_for_dma() and
unmap_urb_for_dma() consistent with that.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is based on a patch that Alan Stern wrote. It did the same simple
thing in both text and binary cases. In the same time, Marton and I
fixed the binary side properly, but this leaves the text to be fixed.
It is not very important due to low maxium data size of text, but
let's add it just for extra correctness.
The pseudocode is too much to keep fixed up, and we have real code
to be used as examples now, so let's drop it too.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In create_companion_file() there is a bogus assignemt to i created for
the express purpose of avoiding an ignored return value warning.
With pre-release GCC-4.6, this causes a 'set but not used' warning.
Kick the problem further down the road by just returning i. All the
callers of create_companion_file() ignore its return value, so all is
good:
o No warnings are issued.
o We still subvert the desires of the authors of device_create_file()
by ignorning error conditions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With pre-release GCC-4.6, we get a 'set but not used' warning when
EHCI_URB_TRACE is not set because we set the qtd variable without
using it.
Rearrange the statements so that we only set qtd if it will be used.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vdbg macro is not used anywhere so it can be removed.
With pre-release GCC-4.6, there are several complaints of variables
that are 'set but not used' caused by the ehci_vdbg() macro expanding
to something that does not contain any of its arguments. We can quiet
this warning by rewriting ehci_vdbg() as a variadic static inline that
does nothing.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pre-release GCC-4.6 now correctly flags this code as dead.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch moves the AMD PLL quirk code in OHCI/EHCI driver to pci-quirks.c,
and exports the functions to be used by xHCI driver later.
AMD PLL quirk disable the optional PM feature inside specific
SB700/SB800/Hudson-2/3 platforms under the following conditions:
1. If an isochronous device is connected to OHCI/EHCI/xHCI port and is active;
2. Optional PM feature that powers down the internal Bus PLL when the link is
in low power state is enabled.
Without AMD PLL quirk, USB isochronous stream may stutter or have breaks
occasionally, which greatly impair the performance of audio/video streams.
Currently AMD PLL quirk is implemented in OHCI and EHCI driver, and will be
added to xHCI driver too. They are doing similar things actually, so move
the quirk code to pci-quirks.c, which has several advantages:
1. Remove duplicate defines and functions in OHCI/EHCI (and xHCI) driver and
make them cleaner;
2. AMD chipset information will be probed only once and then stored.
Currently they're probed during every OHCI/EHCI initialization, move
the detect code to pci-quirks.c saves the repeat detect cost;
3. Build up synchronization among OHCI/EHCI/xHCI driver. In current
code, every host controller enable/disable PLL only according to
its own status, and may enable PLL while there is still isoc transfer on
other HCs. Move the quirk to pci-quirks.c prevents this issue.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alex He <alex.he@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sure we are running on a MX35 processor.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, for ISO and INT, a protocol driver must chose the value for
wMaxPacketSize arbitrarily. The value may be too low, resulting in lesser
than efficient operation or high enough to not work with all UDC drivers.
Take un-initialized wMaxPacketSize as a hint to provide maximum
possible packetsize for the selected endpoint. The protocol may
then choose a value not bigger than that.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added mct_u232_ioctl (implements TIOCMIWAIT command),
mct_u232_get_icount (implements TIOCGICOUNT command) and
mct_u232_msr_to_icount functions. MCT U232 P9 is one of a few usb to
serail adapters which converts USB +/-5v voltage levels to COM +/-15
voltages. So it can also power COM interfaced devices. This makes it
very usable for legacy COM interfaced data-acquisition hardware. I
tested new implementation with AWARE Electronics RM-60 radiation meter,
which sends pulse via RNG COM line whenever new particle is registered.
Signed-off-by: Vadim Tsozik <tsozik@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a tiny difference between PPC32 and PPC64. Microblaze uses the
PPC32 variant.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
[grant.likely@secretlab.ca: Added comment to #endif, moved documentation
block to function implementation, fixed for non ppc and microblaze
compiles]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
gpu/stub: fix acpi_video build error, fix stub kconfig dependencies
drm/radeon/kms: dynamically allocate power state space
drm/radeon/kms: fix s/r issues with bios scratch regs
agp: ensure GART has an address before enabling it
Revert "agp: AMD AGP is used on UP1100 & UP1500 alpha boxen"
amd-k7-agp: remove non-x86 code
drm/radeon/kms/evergreen: always set certain VGT regs at CP init
drm/radeon/kms: add updated ib_execute function for evergreen
drm/radeon: remove 0x4243 pci id
drm/radeon/kms: Enable new pll calculation for avivo+ asics
drm/radeon/kms: add new pll algo for avivo asics
drm/radeon/kms: add pll debugging output
drm/radeon/kms: switch back to min->max pll post divider iteration
drm/radeon/kms: rv6xx+ thermal sensor fixes
drm/nv50: fix display on 0x50
drm/nouveau: correctly pair hwmon_init and hwmon_fini
drm/i915: Only bind to function 0 of the PCI device
drm/i915: Suppress spurious vblank interrupts
drm: Avoid leak of adjusted mode along quick set_mode paths
drm: Simplify and defend later checks when disabling a crtc
...
In drm_crtc_helper_set_config, instead of always forcing all outputs
to DRM_MODE_DPMS_ON, only set them if the CRTC is actually getting a
mode set, as any mode set will turn all outputs on.
This fixes https://lkml.org/lkml/2011/1/24/457
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org (2.6.37)
Reported-and-tested-by: Carlos R. Mafra <crmafra2@gmail.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on a patch from Linus Walleij.
Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface. The changes over Linus' driver are:
- rename txsize_threshold to dmasize_threshold, as this reflects the
purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer. Some DMA controllers
(eg, PL08x) are unable to be configured for scatter DMA and also listen
to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the
final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
its own restrictions on buffer alignment, not the individual DMA engine
users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
causes LBREQ to be asserted for the last seven transfers, rather than
six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
transfer size required to complete the DMA operation.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to store the number of bytes transferred in our host
structure - we can store this directly in data->bytes_xfered.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to switch to data available interrupts if there's at
least half a FIFO depth worth of data remaining, as we'll still get
the FIFO half full interrupt. Keep this interrupt masked off until
we have less than half the FIFO depth worth of data remaining.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sg_miter API provides the required cache maintainence, so we don't
need to do that ourselves. Remove the unnecessary additional cache
maintainence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The data counter counts the number of bytes transferred on the MMC bus.
When a FIFO overrun occurs, we will not have transferred a FIFOs-worth
of data to memory, and so the data counter will be a FIFOs-worth ahead.
If this occurs on a block boundary, we will report one too many sectors
as successful. Fix this.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While the RxFIFO interruption is masked for most 8168, nothing prevents
it to appear in the irq status word. This is no excuse to crash.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>
Some experiment-based action to prevent my 8168 chipsets locking-up hard
in the irq handler under load (pktgen ~1Mpps). Apparently a reset is not
always mandatory (is it at all ?).
- RTL_GIGA_MAC_VER_12
- RTL_GIGA_MAC_VER_25
Missed ~55% packets. Note:
- this is an old SiS 965L motherboard
- the 8168 chipset emits (lots of) control frames towards the sender
- RTL_GIGA_MAC_VER_26
The chipset does not go into a frenzy of mac control pause when it
crashes yet but it can still be crashed. It needs more work.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: Hayes <hayeswang@realtek.com>
I found that one of the 8168c chipsets (concretely XID 1c4000c0) starts
generating RxFIFO overflow errors. The result is an infinite loop in
interrupt handler as the RxFIFOOver is handled only for ...MAC_VER_11.
With the workaround everything goes fine.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Use DMA API as PCI equivalents will be deprecated.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments under "config STUB_POULSBO" are close to correct,
but they are not being followed. This patch updates them to reflect
the requirements for THERMAL.
This build error is caused by STUB_POULSBO selecting ACPI_VIDEO
when ACPI_VIDEO's config requirements are not met.
ERROR: "thermal_cooling_device_register" [drivers/acpi/video.ko] undefined!
ERROR: "thermal_cooling_device_unregister" [drivers/acpi/video.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-greg' of git://gitorious.org/usb/usb:
usb: ehci-omap: Show fatal probing time errors to end user
usb: musb: introduce api for dma code to check compatibility with usb request
usb: musb: maintain three states for buffer mappings instead of two
usb: musb: disable double buffering when it's broken
usb: musb: hsdma: change back to use musb_read/writew
usb: musb: core: fix IRQ check
usb: musb: fix kernel panic during s2ram(v2)
This patch (as1444) adds an unusual_devs entry for an MP3 player from
Coby electronics. The device has two nasty bugs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Jasper Mackenzie <scarletpimpernal@hotmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB Vendor ID and Product ID for a Acton Research Corp.
spectrograph device with a FTDI chip for serial I/O.
Signed-off-by: Michael H Williamson <michael.h.williamson@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB core keeps track of pending resume requests for root hubs, in
order to resolve races between wakeup requests and suspends. However
the code that does this is subject to another race (between wakeup
requests and resumes) because the WAKEUP_PENDING flag is cleared
before the resume occurs, leaving a window in which another wakeup
request might arrive.
This patch (as1447) fixes the problem by clearing the WAKEUP_PENDING
flag after the resume instead of before it.
This fixes Bugzilla #24952.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Paul Bender <pebender@san.rr.com>
Tested-by: warpme <warpme@o2.pl>
Cc: stable <stable@kernel.org> [.36+]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If anyone comes across a high-speed hub that (by mistake or by design)
claims to have no Transaction Translators, plugging a full- or
low-speed device into it will cause the USB stack to crash. This
patch (as1446) prevents the problem by ignoring such devices, since
the kernel has no way to communicate with them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Perry Neben <neben@vmware.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
on ST Micro Connect Lite we have 4 port
Part A and B for the JTAG
Port C Uart
Port D for PIO
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
