When send out skb data to mac80211, orignal code will cause mac80211
unaligned access, so modify code to make mac80211 can natural access.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put the assignment of header_length after pull out extra tx headroom
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800usb chips need to add 1~3 bytes zero padding after each 802.11 header & payload,
and at the end need to add 4 bytes zero padding whether doing TX bulk aggregation or not,
TXINFO_W0_USB_DMA_TX_PKT_LEN in TXINFO must include 1-3 bytes padding after 802.11 header & payload
but do not include 4 bytes end zero padding.
In rt2800usb_get_tx_data_len do not consider multiple of the USB packet size case, sometimes this will
cause USB DMA problem.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the code a bit more portable to architectures that do not support
KSEG1ADDR.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_RT2800PCI_PCI and CONFIG_RT2800PCI_SOC are strictly not needed
as we can check the dependent symbols directly in the rest of Kconfig
and the code, so clean up the Kconfig namespace a bit.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling of RT30xx devices via Kconfig variables was introduced when these
devices weren't properly supported yet.
Now that that they are properly supported and functional, we can remove these
Kconfig variables for RT30xx devices and simply enable them whenever rt2800pci
and/or rt2800usb is enabled.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
General clean up of the Kconfig part for RT28XX devices.
Also remove the indications of non functional support for rt27xx/rt28xx/rt30xx
devices, as this is no longer true. They just work fine.
Finally, remove the experimental indications for rt27xx/rt28xx/rt30xx devices
as that is no longer true. Keep the experimental indications for rt33xx/rt35xx
devices, though.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modified from Eddy's patch by adding the RT3370 USB support as well.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Eddy Tsai <Eddy_Tsai@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some hardware the REGISTER_BUSY_COUNT isn't sufficient,
increase the REGISTER_BUSY_COUNT to 100 to catch most
devices which have more problems with accessing the registers.
For normal operating devices nothing would change as they will
exit the loop early anyway.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the remaining bit of aava dependent and related bits from driver
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The spectra nand driver takes quite some time to initialize because
it needs to scan the whole nand disk to find the latest block table.
This patch initializes the spectra nand driver asynchronously so that
other things in the kernel can initialize in parallel to the scanning
operation.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently there are some driver initialization logic that
is not part of nand_pci_probe function. This will result in
that part of driver initialization code executing even on
platforms without the corresponding hardware which is always
dangerous.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
GCC complains that if (info->CardReady) is false we kfree() an
uninitialized pointer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Get rid of the private PCI access routines and replace with standard calls from linux/pci.h in nicpci.c
(The private versions are still used in siutils.c... for now)
Signed-off-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do the substitution (and then fix all the dang lines that were pushed past 80 columns.)
Some of the touched lines triggered checkpatch warnings for completely unrelated
reasons that were already there. Those will have to be addressed later.
Signed-off-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
irq_of_parse_and_map() has an unsigned return type.
Testing for a negative error value doesn't work here.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_init_one() should return negative value on error.
By mistake it returns ENODEV instead of -ENODEV.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I am not family with RealTek RTL-8139C+ series 10/100 PCI Ethernet driver.
I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(status & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If these are right, driver will set ip_summed with CHECKSUM_UNNECESSARY for other
upper protocol, e.g. sctp, igmp protocol. This will cause protocol stack ignores
checksum check for packets with invalid checksum.
This patch is only compile-test.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If r8196 received packets with invalid sctp/igmp(not tcp, udp) checksum, r8196 set skb->ip_summed
wit CHECKSUM_UNNECESSARY. This cause that upper protocol don't check checksum field.
I am not family with r8196 driver. I try to guess the meaning of RxProtoIP and IPFail.
RxProtoIP stands for received IPv4 packet that upper protocol is not tcp and udp.
!(opts1 & IPFail) is true means that driver correctly to check checksum in IPv4 header.
If it's right, I think we should not set ip_summed wit CHECKSUM_UNNECESSARY for my sctp packets
with invalid checksum.
If it's not right, please tell me.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
blk_queue_ordered() has been deprecated and replaced with
blk_queue_flush() by Tejun. However, use of blk_queue_ordered()
in spectra nand driver has not been converted yet and thus results
in the following build error.
drivers/staging/spectra/ffsport.c: In function SBD_setup_device:
drivers/staging/spectra/ffsport.c:659: error: implicit declaration of function blk_queue_ordered
drivers/staging/spectra/ffsport.c:659: error: QUEUE_ORDERED_DRAIN_FLUSH undeclared (first use in this function)
drivers/staging/spectra/ffsport.c:659: error: (Each undeclared identifier is reported only once
drivers/staging/spectra/ffsport.c:659: error: for each function it appears in.)
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Log LRO off message while disabling rx checksum only when
LRO is already enabled.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for CN1000Q adapter
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of kdump environment the function may be in unknown state.
Reset the function using PCI FLR before initializing it.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow minimum bandwidth to be set zero
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __attribute__((format... to several functins
Make formats and arguments match.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cmd->serial_number is never tested in any path we reach; therefore we may
remove the call to scsi_cmd_get_serial() inside DEF_SCSI_QCMD, the SCSI
host_lock acquisition surrounding it, and our own SCSI host_lock
unlock+relock cycle.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The stradis driver is on its way out, but it should still be marked
correctly as depending on the big kernel lock. It could easily be
changed to not require it if someone decides to revive the driver and
port it to v4l2 in the process.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Nathan Laredo <laredo@gnu.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Explain the reason for the apparently odd choice of year offset so we don't
get more questions about it.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
LKML-Reference: <20101117121050.9998.89348.stgit@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The recent patch to fix the removal of a non-existing proc
directory introduced this build problem for !CONFIG_PROC_FS:
drivers/block/cciss.c:4929: error: 'proc_cciss' undeclared (first use in this function)
Fix it by moving proc_cciss outside of the CONFIG_PROC_FS scope.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit b5c26f97ec introduced some breakage for the OLPC XO-1 laptop,
differences in the output video signal after the patch caused some problems
with the XO's display controller chip.
Reviewing of that commit against the AMD Geode LX Data Book, it seems
that these bits were being set inversely. In both cases, active high
output is denoted by a value of 0. See section 6.8.3.44 of the databook
from February 2009 (Publication ID: 33234H)
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is an integer overflow in fb_set_user_cmap() because cmap->len * 2
can wrap. It's basically harmless. Your terminal will be messed up
until you type reset.
This patch does three things to fix the bug.
First, it checks the return value of fb_copy_cmap() in fb_alloc_cmap().
That is enough to fix address the overflow.
Second it checks for the integer overflow in fb_set_user_cmap().
Lastly I wanted to cap "cmap->len" in fb_set_user_cmap() much lower
because it gets used to determine the size of allocation. Unfortunately
no one knows what the limit should be. Instead what this patch does
is makes the allocation happen with GFP_KERNEL instead of GFP_ATOMIC
and lets the kmalloc() decide what values of cmap->len are reasonable.
To do this, the patch introduces a function called fb_alloc_cmap_gfp()
which is like fb_alloc_cmap() except that it takes a GFP flag.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>