This affects the get/set of the current Ambient Light Zone. Reading
should return an integer between 1..3 (1 = Daylight, 2 = office, 3 =
dark). Writing a value between 1..3 forces the backlight controller to
enter the corresponding Ambient Light Zone. Writing 0 returns to normal
operation.
Fix valid range checking so we don't write invalid values to the
controller, and make sure we subtract 1, since this is what the register
definition (CFGR:BLV) requires. Otherwise the values written don't work
correctly.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The intensity of the backlight can be varied from a range of
max_brightness to zero. Though most, if not all the pwm based backlight
devices start flickering at lower brightness value. And also for each
device there exists a brightness value below which the backlight appears
to be turned off though the value is not equal to zero.
If the range of brightness for a device is from zero to max_brightness. A
graph is plotted for brightness Vs intensity for the pwm based backlight
device has to be a linear graph.
intensity
| /
| /
| /
|/
---------
0 max_brightness
But pratically on measuring the above we note that the intensity of
backlight goes to zero(OFF) when the value in not zero almost nearing to
zero(some x%). so the graph looks like
intensity
| /
| /
| /
| |
------------
0 x max_brightness
In order to overcome this drawback knowing this x% i.e nothing but the low
threshold beyond which the backlight is off and will have no effect, the
brightness value is being offset by the low threshold value(retaining the
linearity of the graph). Now the graph becomes
intensity
| /
| /
| /
| /
-------------
0 max_brightness
With this for each and every digit increment in the brightness from zero
there is a change in the intensity of backlight. Devices having this
behaviour can set the low threshold brightness(lth_brightness) and pass
the same as platform data else can have it as zero.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Arun Murthy <arun.murthy@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eliminate section mismatch warning by marking s6e63m0_probe() as __devinit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Cc: InKi Dae <inki.dae@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LCD was turned on if the variable power was > 0, but that was
incorrect. The LCD has to be turned on in NORMAL and UNBLANK case.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LCD was turned on if the variable power was > 0, but that was
incorrect. The LCD has to be turned on in NORMAL and UNBLANK case.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gamma_table is not writable, so set permissions to 0444.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the event that none of the configs are set (CONFIG_LEDS_GPIO_PLATFORM,
CONFIG_LEDS_GPIO_OF, CONFIG_LEDS_GPIO_PLATFORM), we will return a bogus
value when initializing the module.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide configuration and compilation support for LP5521 and LP5523
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LP5523 chip is nine channel led driver with programmable engines. Driver
provides support for that chip for direct access via led class or via
programmable engines.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patchset provides support for LP5521 and LP5523 LED driver chips from
National Semicondutor. Both drivers supports programmable engines and
naturally LED class features.
Documentation is provided as a part of the patchset. I created "leds"
subdirectory under Documentation. Perhaps the rest of the leds*
documentation should be moved there.
Datasheets are freely available at National Semiconductor www pages.
This patch:
LP5521 chip is three channel led driver with programmable engines. Driver
provides support for that chip for direct access via led class or via
programmable engines.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, blinking LEDs can be awkward because it is not guaranteed that
all LEDs implement blinking. The trigger that wants it to blink then
needs to implement its own timer solution.
Rather than require that, add led_blink_set() API that triggers can use.
This function will attempt to use hw blinking, but if that fails
implements a timer for it. To stop blinking again, brightness_set() also
needs to be wrapped into API that will stop the software blink.
As a result of this, the timer trigger becomes a very trivial one, and
hopefully we can finally see triggers using blinking as well because it's
always easy to use.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a signedness bug so "ret" was never less than zero and that
breaks the error handling. Also in the original code it would overwrite
ret and the result is still negative but it's bogus number instead of the
correct error code.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i2c_smbus_read_byte_data() may return negative error code. This is not
seen to als_sensing_range_store() as the result is stored in unsigned int.
Made it signed.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Cc: Hong Liu <hong.liu@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Anantha Narayanan <anantha.narayanan@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"ret_val" is supposed to be signed here or the error handling breaks.
Also we should check the return value from i2c_smbus_read_byte_data().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The size calculation is done incorrectly here because it should include
both the start and end (end - start + 1). It's easiest to just use
resource_size() which does the right thing.
I was worried there was something non-standard going on because the
printk() subtracts "end - 1", but the rest of the file uses the normal
resource size calculations. This function is only called from
fsl_rio_setup() in arch/powerpc/sysdev/fsl_rio.c and the calculation
there is also:
port->iores.start = law_start;
port->iores.end = law_start + law_size - 1;
So I think this is the correct fix.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix these warnings:
drivers/macintosh/adb-iop.c: In function `adb_iop_complete':
drivers/macintosh/adb-iop.c:85: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c:92: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c: In function ¡adb_iop_listen¢:
drivers/macintosh/adb-iop.c:111: warning: comparison of distinct pointer types lacks a cast
drivers/macintosh/adb-iop.c:151: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to add appropriate locking when toggling mac mouse emulation
on and off to ensure that input device and handler are in consistent
state.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In addition to forcing recalibrations upon detection of cursor jumps (and
performing them quicker than before), detect and discard errant 'jump'
packets caused by a firmware bug, which are then repeated with each one
being approximately half the delta of the one previously (as if it is
averaging out)
Based on original work by Paul Fox.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The old implementation of spew detection simply tracked the overall
position delta of the cursor over every 100 packets. We found that
this causes occasional false positives in spew detection, and also
that the conditions of the spewy packets are perhaps more fixed than
we once thought.
Rework the spew detection to look for packets of specific small
delta, and only recalibrating if the overall movement delta stays
within expected bounds.
Also discard duplicate packets in the advanced mode, which appear
to be very common. If we don't, the spew detection kicks in far
too early. If we get a large spew of duplicates, request a
recalibration straight up.
Based on earlier work by Paul Fox.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a "hgpk_mode" sysfs attribute that allows selection between 3 options:
Mouse (the existing option), GlideSensor and PenTablet.
GlideSensor is an enhanced protocol for the regular touchpad mode that
additionally reports pressure and uses absolute coordinates. We suspect
that it may be more reliable than mouse mode in some environments.
PenTablet mode puts the touchpad into resistive mode, you must then use
a stylus as an input. We suspect this is the most reliable way to drive
the touchpad.
The GlideSensor and PenTablet devices expose themselves with the
intention of being combined with the synaptics X11 input driver.
Based on earlier work by Paul Fox.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ixpad can never be NULL here; if it is NULL we would not have been bound to
the interface and then why would we be called?
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Properly free the resources in error path by the reverse order of resource
allocation.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In xpad_led_disconnect(), what we really want is to kfree(xpad_led).
In xpad_disconnect(), add a missing kfree(xpad->bdata) to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In current implementation, xpad_probe return 0 when
usb_alloc_urb failed for xpad->bulk_out and kzalloc failed for xpad->bdata.
This patch removes the initialization for error variable,
assign the error code at the place the error happens instead.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
MMC hosts that poll for card detection by defining the MMC_CAP_NEEDS_POLL
flag have a race on rmmod, where the delayed work is cancelled without
waiting for completed polling. To prevent this a _sync version of the work
cancellation has to be used.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Set VM_PFNMAP in the privcmd mmap file_op, rather than later in
xen_remap_domain_mfn_range when it is too late because
vma_wants_writenotify has already been called and vm_page_prot has
already been modified.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Setting Rx FIFO size to 1 reduces reader process wakeup latency up to
20x for baud rates <= 9600. This patch sets the Rx FIFO size to 1 for
baud rates <= 9600 or if low latency has been requested for the tty.
Signed-off-by: Michael Trimarchi <michael@gandalf.sssup.it>
Signed-off-by: Bruno Morelli <bruno@evidence.eu.com>
Signed-off-by: Baurzhan Ismagulov <ibr@radix50.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[Original From Ken Mills but I redid it using pr_ helpers instead]
Also fix up coding style, there are two warnings left but that is where
the CodingStyle tools blow up because they cannot handle
if (blah) {
foo
} else switch (x) {
case 1:
}
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mux supports several encoding schemes. Encoding 0 is a "not
recommended" mode still sometimes used. This has now been tested with
hardware that supports this mode, and found wanting.
Fix the FCS handling in this mode and correct the state machine.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a driver for the serial ports found in VIA and WonderMedia
Systems-on-Chip. Interrupt-driven FIFO operation is implemented.
The hardware also supports pure register-based operation (which is
slower) and DMA-based FIFO operation. As the FIFOs are only 16 bytes
long, DMA operation is probably not worth the hassle.
Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prototype driver for the IFX6x60 series of SPI attached modems by Jim
Stanley and Russ Gorby
Signed-off-by: Russ Gorby <richardx.r.gorby@intel.com>
[Some reworking and a major cleanup]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the mux is configured with a large mru/mtu the existing code gets the
byte ordering wrong for the header.
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The n2 field is settable but didn't get propogated
Signed-off-by: Ken Mills <ken.k.mills@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The port lock exists to protect these resources, so we need to grab it
before making changes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we are using early serial, don't let the normal console rewind
the log buffer, since that causes things to be printed multiple times.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't need to force a SSYNC here as the LSR register will already
be updated by the time we get back to reading it. This speeds up TX
throughput and lowers general system overhead (since SSYNC is system
wide, not peripheral-specific).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Blackfin systems, peripherals that have optional DMA support always
route their interrupts through the corresponding DMA channel -- even
when DMA is not being used. So in PIO mode, we still need to request
the DMA channel (so interrupts are delivered) which means we need to
always include the DMA header for the DMA defines/functions.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kay Sievers pointed out that usage of POLLIN is well defined by POSIX,
and the current usage here doesn't follow that definition. So let's
duplicate the same semantics as implemented by sysfs_poll() instead.
Signed-off-by: Nicolas Pitre <nicolas.pitre@canonical.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
drivers/char/amiserial.c: In function ?rs_ioctl?:
drivers/char/amiserial.c:1302: warning: unused variable ?icount?
commit 0587102cf9 ("tty: icount changeover for
other main devices") removed the users, but not the actual variable.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB2.0 spec 9.6.6 says: For all endpoints, bit 10..0 specify the maximum
packet size(in bytes).
So the wMaxPacketSize mask should be 0x7ff rather than 0x3ff.
This patch should be queued for the stable tree. The bug in
xhci_endpoint_init() was present as far back as 2.6.31, and the bug in
xhci_get_max_esit_payload() was present when the function was introduced
in 2.6.34.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Jiri Slaby reports spinlock is held while calling kmalloc(GFP_KERNEL)
and request_irq() in xhci_resume().
Release the spinlock when setup interrupt.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
If the xHCI host controller shares an interrupt line with another device,
the xHCI driver needs to check if the interrupt was generated by its
hardware. Unfortunately, the user will see a ton of "Spurious interrupt."
lines if the other hardware interrupts often. Lawrence found his dmesg
output cluttered with this output when the xHCI host shared an interrupt
with his i915 hardware.
Remove the warning, as sharing an interrupt is a normal thing.
This should be applied to the 2.6.36 stable tree.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Lawrence Rust <lvr@softsystem.co.uk>
Cc: stable@kernel.org
It seems idev field in struct rtable has no special purpose, but adding
extra atomic ops.
We hold refcounts on the device itself (using percpu data, so pretty
cheap in current kernel).
infiniband case is solved using dst.dev instead of idev->dev
Removal of this field means routing without route cache is now using
shared data, percpu data, and only potential contention is a pair of
atomic ops on struct neighbour per forwarded packet.
About 5% speedup on routing test.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only ever used the PRB0, neglecting the secondary ring buffers, and
now with the advent of multiple engines with separate ring buffers we
need to excise the anachronisms from our code (and be explicit about
which ring we mean where). This is doubly important in light of the
FORCEWAKE required to read ring buffer registers on SandyBridge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>