Commit 46034dca51 (USB: musb_gadget_ep0: stop
abusing musb_gadget_set_halt()) forgot to restart a queued request after
clearing the endpoint halt feature. This results in a couple of USB resets
while enumerating the file-backed storage gadget due to CSW packet not being
sent for the MODE SENSE(10) command.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the issue which was observed while transfering
a large file ( > 20MB) over USB (OMAP MUSB controller acts as USB host)
to an attached USB thumb drive.
It was found that CDB field of CBW packet was set to 0x0. This was
due to missing a barrier before DMA engine starts transfer.
This buffer is allocated using dma_alloc_coherent which gives
non-cacheble but bufferable memory and hence needed a write
memory barrier to flush the write buffer.
More info on this thread is here:
http://www.spinics.net/lists/linux-omap/msg33987.html
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space
of request buffer, so fix it.
Also set max_len of cppi dma channel as max size of
int type, so make musb dma handling happier.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Complete the current request only if the data transfer is over.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
DMA length should not go beyond the availabe space of request buffer,
so fix it.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one bugs of OUT transfer in double buffer case:
-the current code only enable autoclear for dma mode 1, and not
for dma mode 0
Without this patch, test #5 of usbtest can't be passed if we
configure musb as g_zero and use fifo mode 3 to enable double
buffer mode.
With this patch and the following patch(fix dma length),
on my beagle B5, test#5(queued bulk out) may go beyond
18Mbyte/s(seems dma mode 0 is quicker in double buffer case)
if musb is configured as g_zero and fifo mode 3 is taken, follows
the test command:
#./testusb -D DEV_NAME -c 1024 -t 5 -s 32768 -g 8 [1]
Also I have tested this patch can't make g_ether broken.
[1],source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes one infinite hang of bulk IN transfer in double buffer
case, the hang can be observed easily by test #6 of usbtest if musb is
configured as g_zero and fifo mode 3 is taken to enable double fifo.
In fact, the patch only removes the check for non-empty fifo before
loading data from new request into fifo since the check is not correct:
-in double buffer case, fifo may accommodate more than one packet,
even though it has contained one packet already and is non-empty
-since last DMA is completed before calling musb_g_tx, it is sure
that fifo may accommodate at least one packet
Without applying the patch, new requst enqueued from .complte may not
have a chance to be loaded into fifo, then will never be completed and
cause infinite hangs.
With the patch, on my beagle B5, test#6(queued bulk in) can be passed and
test result may go beyond 33Mbyte/s if musb is configured as g_zero and
fifo mode 3 is taken, follows the test command:
#testusb -D DEV_NAME -c 1024 -t 6 -s 32768 -g 8 [1]
[1],
-source of testusb : tools/usb/testusb.c under linux kernel;
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent changes in the usbhid layer exposed a bug in usbcore. If
CONFIG_USB_DYNAMIC_MINORS is enabled then an interface may be assigned
a minor number of 0. However interfaces that aren't registered as USB
class devices also have their minor number set to 0, during
initialization. As a result usb_find_interface() may return the
wrong interface, leading to a crash.
This patch (as1418) fixes the problem by initializing every
interface's minor number to -1. It also cleans up the
usb_register_dev() function, which besides being somewhat awkwardly
written, does not unwind completely on all its error paths.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Philip J. Turmel <philip@turmel.org>
Tested-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Matthias Bayer <jackdachef@gmail.com>
CC: Jiri Kosina <jkosina@suse.cz>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In order to support multiple ST platform devices, a new symbol
'st_get_plat_device' earlier needed to be exported by the arch/XX/brd-XX.c
file which intends to add the ST platform device.
On removing this dependency, now inside ST driver maintain the array of
ST platform devices that would be registered.
As of now let id=0, as and when we end up having such platforms
where mutliple ST devices can exist, id would come from
protocol drivers (BT, FM and GPS) as to on which platform device
they want to register to.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Anca Emanuel <anca.emanuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to the current edac-core limits, we cannot represent a per-channel
memory size, for FB-DIMM drivers. So, we need to sum-up all values
for each slot, in order to properly represent the total amount of
memory found by the i7300 driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is still somewhat fake, as the pages may not be on this exact order,
and may even be used in mirror mode, but this is a best guess than the
other random fake values.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Having switched over to the newly introduced cpdma layer, this patch now
removes a whole bunch of code that is now unused. This patch has been
maintained separate strictly for reasons of readability.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch hooks up the emac driver with the newly separated cpdma driver.
Key differences introduced here:
- The old buffer list scheme is no longer required
- The original code maintained mac address per rx channel, even if only one
rx channel was being used. With this change, mac address is maintained
device wide. If support for multiple rx channels is added in future, this
will need to be reworked a bit.
- The new CPDMA code handles short packets better than before. The
earlier code was adjusting the length up, without ensuring that the tail
end of the padding was cleared - a possible security issue. This has been
fixed to use skb_padto().
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In addition to being embedded into the EMAC controller, the CPDMA hardware
block is used in TI's CPSW switch controller. Fortunately, the programming
interface to this hardware block remains pretty nicely consistent across these
devices.
This patch adds a new CPDMA services layer, which can then be reused across
EMAC and CPSW drivers.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes code that has been rendered useless by the previous patches
in this series.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch switches the emac implementation over to the newly separated
MDIO driver.
With this, the mdio bus frequency defaults to a safe 2.2MHz. Boards may
optionally specify a bus frequency via platform data.
The phy identification scheme has been modified to use a phy bus id instead
of a mask. This largely serves to eliminate the "phy search" code in emac
init.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Davinci's MDIO controller is present on other TI devices, without an
accompanying EMAC. For example, on tnetv107x, the same MDIO module is used in
conjunction with a 3-port switch hardware.
By separating the MDIO controller code into its own platform driver, this
patch allows common logic to be reused on such platforms.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the DaVinci NAND driver to use the
new AEMIF timing setup API to configure the NAND access
timings.
Earlier, AEMIF configuration was being done as a special
case for DM644x board, but now more boards emerge which have
capability to boot for other media (SPI flash, NOR flash) and
have the kernel access NAND flash. This means that kernel cannot
always depend on the bootloader to setup the NAND.
Also, on platforms such as da850/omap-l138, the aemif input
frequency changes as cpu frequency changes; necessiating
re-calculation of timimg values as part of cpufreq transtitions.
This patch forms the basis for adding that support.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds support to configure the AEMIF interface
with supplied timing values.
Since this capability is useful both from NOR and NAND
flashes, it is provided as a new interface and in a file
of its own.
AEMIF timing configuration is required in cases:
1) Where the AEMIF clock rate can change at runtime (a side
affect of cpu frequency change).
2) Where U-Boot does not support NAND/NOR but supports other
media like SPI Flash or MMC/SD and thus does not care about
setting up the AEMIF timing for kernel to use.
3) Where U-Boot just hasn't configured the timing values and
cannot be upgraded because the box is already in the field.
Since there is now a header file for AEMIF interface, the
common (non-NAND specific) defines for AEMIF registers have
been moved from nand.h into the newly created aemif.h
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes the black screen bug on Dell e6510, by
adding two delays to give the eDP panel time to turn on before we
continue with the next write.
300ms is rather arbitray and a rather long sleep, we need to find a way
of refining this value.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29278
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In commit e517a5e970 the call to
map_page_into_agp() got removed from intel_i830_setup_flush(), but the
counterpart call from intel_i830_fini_flush() to unmap_page_from_agp()
was left in place.
Additionally, the page allocated here never gets its physical address
used for sending to hardware, so there's no need to allocate it with
GFP_DMA32. Nor is __GFP_ZERO really necessary, as the page is used
only to store data to force flushing of some internal processor state.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
First step, lets have a look at the values for troublesome panels and
see if they may be used to improve our link training.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to drain the pending flips prior to disabling the pipe during
modeset, and these need to be done in an uninterruptible fashion.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As we presume space is signed when computing and looking for wrap along,
make it so.
Reported-by: Owain G. Ainsworth <zerooa@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This is a partial revert of 0b1974de66 ("Fix typo: configuation
=> configuration") as this hunk is removed in net-next.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that hiddev_driver isn't being used for anything, there's no
reason to keep it around. This patch (as1419) gets rid of it
entirely.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Let the HID core handle input device setup and HID-compliant reports.
This driver then only has to worry about the non-standard reports.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just in case someone, somewhere, does something difficult. This also
removes one path that was different between fermi and non-fermi.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francesco Marella <fmarl@paranoici.org>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_bios_fp_mode() zeroes the mode struct before filling in relevant
entries. This nukes the mode id initialised by drm_mode_create(), and
causes warnings from idr when we try to remove the mode.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>