In the case when an ep_connect request is interrupted due to route
request stall, if the iSCSI daemon is terminated by the user, the chip
will be left in a state which will not get cleaned up upon module
removal. Upon module reload, when the same context id is used for a
new connection, chip panic would occur.
This patch adds chip cleanup in the module removal path.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Specific to the Broadcom 10g chipset, the CFC delete operation must be
coupled with the cm_abort/close with does the SRC delete/terminate offload
operation prior.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Acked-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Expanded the TMF request routine to support other TMFs such as LUN
RESET, etc.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
According to RFC3720, nopout packet sent in response to unsolicited
nopin packet requesting a response must retain the TTT of the requester.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes a resource address formatting problem where the first byte
was being zeroed out.
Also, the device ID is now made available as a sysfs attribute.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added cxgb4i iSCSI driver.
This patch implements the cxgb4i iscsi connection acceleration for the
open-iscsi initiator.
The cxgb4i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[PATCH v5 1/3] libcxgbi: common library for cxgb3i and cxgb4i
From: Karen Xie <kxie@chelsio.com>
Extracts common functions to libcxgbi.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In lpfc_cleanup_pending_mbox() we already have IRQs disabled so we don't
need to disable them again.
Also in lpfc_sli_intr_handler() there is a typo where it has
spin_unlock_irq() instead of just spin_unlock().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Patch has only been compile tested.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Patch has only been compile tested.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds a fc_host setting to store the
default dev_loss_tmo. It is used if the driver
has a callack to get the value from the LLD. If
the callback is not set, then we use the fc class
module default value.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is one of those paranoid checks which should at least tell
us that something is about to go haywire after we've disabled
GART table walk probes which is done by default now on AMD.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <1283531981-7495-4-git-send-email-bp@amd64.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Current code tramples over bit F3x90[6] which can be used to
disable GART table walk probes. However, this bit should be set
for performance reasons (speed up GART table walks). We are
allowed to do that since we put GART tables in UC memory later
anyway. Make it so.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <1283531981-7495-3-git-send-email-bp@amd64.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is a GARTEN so use that and drop the duplicate.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <1283531981-7495-2-git-send-email-bp@amd64.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
selector is used as array index of info->supported_voltages
Thus the valid value range should be 0 .. info->voltages_len -1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In choose_voltage(), we use i as array index of info->vol_table.
The valid value range for i should be 0 .. ARRAY_SIZE(info->vol_table) - 1.
Take LDO1 as example, ARRAY_SIZE(LDO1_table) is 4, vol_nbits of LDO1 is 2.
for (i = 0; i < (2 << info->vol_nbits); i++) is equivalent to
for (i = 0; i < 8; i++)
which is wrong.
The same value range checking also applies for index in pm8607_list_voltage().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@openource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
We must reduce our own mtu when we reduce the mtu of any device we use
to transfer our packets. Otherwise we may accept to large packets which
gets dropped by the actual device.
Reported-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Information about dropped packets are usually only interesting for
debugging purposes and otherwise open the possibility to flood the logs
of the target machine with useless information.
pr_debug will not output those information on a nodebug kernel.
Reported-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
batman_if has the name of the net_dev as extra string in its own
structure, but also holds a reference to the actual net_device structure
which always has the current name of the device. This makes it
unneccessary and also more complex because we must update the name in
situations when we receive a NETDEV_CHANGENAME event.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes all remaining global variables and includes the
necessary bits into the bat_priv structure. It is the last
remaining piece to allow multiple concurrent mesh clouds on the
same device.
A few global variables have been rendered obsolete during the process
and have been removed entirely.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch replaces the static bat0 interface with a dynamic/abstracted
approach. It is now possible to create multiple batX interfaces by
assigning hard interfaces to them. Each batX interface acts as an
independent mesh network. A soft interface is removed once no hard
interface references it any longer.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We must ensure that all interesting data is linear and not paged out to
access all information in a header or a full batman-adv related packet.
Otherwise we may drop packets which have non-linear headers but which
hold valid data.
This doesn't affect non-linear skbs which have all headers in a linear
head unless we must process the whole packet like in ogms or vis
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can use skb_cow instead of a handwritten function to test and create
a writable skb buffer. This also allows us to pre-allocate headroom to
be able to send the data without re-allocating the buffer again to add
the ethernet header.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The vis information structure is used in a way that it can be transfered
directly as packet. It still had to be copied into a skb because of an
extra buffer used for the actual preparation of the data. This is
unnecessary and can be replaced by a simple clone instead of an full
copy before each send.
This makes also the send_raw_packet function obsolete.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All originator messages are send through aggregation buffers. Those
buffers can directly be allocated as skb to reduce the cost of
allocation an extra buffer and copying them to a new allocated skb
directly before it gets send.
Now only the skb must be cloned in case of send_packet_to_if as it gets
called by send_packet for each interface. Non-primary ogms must not
cloned at all because they will only send once and the forward_packet
structure is freed by send_outstanding_bat_packet afterwards.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
batman-adv tries to resend broadcasts on all interfaces up to three
times. For each round and each interface it must provide a skb which
gets consumed by the sending function.
It is unnecessary to copy the data of each broadcast because the actual
data is either not shared or already copied by add_bcast_packet_to_list.
So it is enough to just copy the skb control data
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
my_skb_push provided an easy way to allocate enough headroom in
situation were we don't have enough space left and move the data pointer
to the new position, but we didn't checked wether we are allowed to
write to the new pushed header. This is for example a problem when the
skb was cloned and thus doesn't have a private data part.
my_skb_head_push now replaces my_skb_push by using skb_cow_head to
provide only a large enough, writable header without testing for the
rest of the (maybe shared) data. It will also move the data pointer
using skb_push when skb_cow_head doesn't fail.
This should give us enough flexibility in situation were skbs will be
queued by underlying layers and still doesn't unnecessarily copy the
data in situations when the skb was consumed right away during
dev_queue_xmit.
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Batman-adv globally registered the batman-adv packet type and installed
a hook to batman_skb_recv(). Each interface receiving a packet with that
type would end up in this function which then had to loop through all
batman-adv internal interface structures to find the its meta data. The
more interfaces a system had the longer the loops might take. Each and
every packet goes through this function making it a performance critical
loop.
This patch installs the hook for each activated interface. The called
batman_skb_recv() can distinguish these calls, therefore avoiding the
loop through the interface structures.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is unnecessary to generate an icmp packet in an extra memory region
and than copying it to a new allocated skb.
This also resolved the problem that we do inform the user that we
couldn't send the packet because we couldn't allocate the socket buffer.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements a simple layer2 fragmentation to allow traffic
exchange over network interfaces with a MTU smaller than 1500 bytes. The
fragmentation splits the big packets into two parts and marks the frames
accordingly. The receiving end buffers the packets to reassemble the
orignal packet before passing it to the higher layers. This feature
makes it necessary to modify the batman-adv encapsulation for unicast
packets by adding a sequence number, flags and the originator address.
This modifcation is part of a seperate packet type for fragemented
packets to keep the original overhead as low as possible. This patch
enables the feature by default to ensure the data traffic can travel
through the network. But it also prints a warning to notify the user
about the performance implications.
Note: Fragmentation should be avoided at all costs since it has a
dramatic impact on the performance, especially when it comes wifi
networks. Instead of a single packet, 2 packets have to be sent! Not
only valuable airtime is wasted but also packetloss decreases the
throughput. A link with 50% packetloss and fragmentation enabled is
pretty much unusable.
Signed-off-by: Andreas Langer <an.langer@gmx.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
to support multiple mesh devices later, we need to move global variables
like the queues into corresponding private structs bat_priv of the soft
devices.
Note that this patch still has a lot of FIXMEs and depends on the global
soft_device variable. This should be resolved later, e.g. by referencing
the parent soft device in batman_if.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
[sven.eckelmann@gmx.de: Rework on top of current version]
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Kernighan algorithm is not able to calculate the number of set bits
in parallel and the compiler cannot replace it with optimized
instructions.
The kernel provides specialised functions for each cpu which can either
use a software implementation or hardware instruction depending on the
target cpu.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Ethernet header is counted when transmitting a packet, so it should also
be counted when receiving a packet. With this patch, the rx_bytes and tx_bytes
statistics behave like an ordinary Ethernet interface.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Version 2010.1.0 of the extra kernel module was released and thus the
documentation should be updated and everything prepared for the the
upcoming patchset.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The changelog is only generated on standalone releases. Thus it has no
real value for the in-kernel version of batman-adv.
Reported-by: Abraham Arce <abraham.arce.moreno@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 96d592ed59.
The netfilter hook seems to be misused and may leak skbs in situations
when NF_HOOK returns NF_STOLEN. It may not filter everything as
expected. Also the ethernet bridge tables are not yet capable to
understand batman-adv packet correctly.
It was only added for testing purposes and can be removed again.
Reported-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the vb_util.c file that fixes many style
issues found by the checkpatch.pl tool.
- extra spaces
- invalid code indent
- extra braces
- invalid comment style
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the vb_init.c file that fixes many style
issues found by the checkpatch.pl tool.
- extra spaces
- invalid code indent
- extra braces
- invalid comment style
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the vb_setmode.c file that fixes many style
issues found by the checkpatch.pl tool.
- extra spaces
- invalid code indent
- extra braces
- invalid comment style
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a patch to the vb_ext.c file that fixes many style
issues found by the checkpatch.pl tool.
- extra spaces
- invalid code indent
- extra braces
- invalid comment style
Signed-off-by: Prashant P. Shah <pshah.mumbai@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes a duplicate include directive in
drivers/staging/rtl8187se/ieee80211/ieee80211.h.
Signed-off-by: Andre Nogueira <andre.neo.net@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>