In videobuf_setup reject buffers that are too small for the configured
format. Fixes v4l2-compliance issue.
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
Reviewed-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adapt rcar_vin_querycap() so that cap->bus_info is populated with
something meaningful/unique.
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This adds V4L2_MBUS_FMT_RGB888_1X24 input format support
which is used by the ADV7612 chip.
Modified to use MEDIA_BUS_FMT_* constants
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commits moves the Intersil/Techwell PCI vendor ID, and
the device IDs for the TW68 PCI video capture cards.
This will allow to support future Intersil/Techwell devices
without duplicating the IDs.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On the place of the source entity name, the sink entity name was printed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platforms using the OMAP3 ISP have all switched to DT, drop platform
data support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert g2d_userptr_get_dma_addr() to pin pages using get_vaddr_frames().
This removes the knowledge about vmas and mmap_sem locking from exynos
driver. Also it fixes a problem that the function has been mapping user
provided address without holding mmap_sem.
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Conversion to the use of pinned pfns made some functions unused. Remove
them. Also there's no need to lock mmap_sem in __buf_prepare() anymore.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert vb2_dc_get_userptr() to use frame vector infrastructure. When we
are doing that there's no need to allocate page array and some code can
be simplified.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert vb2_vmalloc_get_userptr() to use frame vector infrastructure.
When we are doing that there's no need to allocate page array and some
code can be simplified.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide simple helper functions to map virtual address range into an
array of pfns / pages.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns() instead of
hand made mapping of virtual address to physical address. Also the
function leaked page reference from get_user_pages() so fix that by
properly release the reference when omap_vout_buffer_release() is
called.
Signed-off-by: Jan Kara <jack@suse.cz>
[hans.verkuil@cisco.com: remove unused variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide new function get_vaddr_frames(). This function maps virtual
addresses from given start and fills given array with page frame numbers of
the corresponding pages. If given start belongs to a normal vma, the function
grabs reference to each of the pages to pin them in memory. If start
belongs to VM_IO | VM_PFNMAP vma, we don't touch page structures. Caller
must make sure pfns aren't reused for anything else while he is using
them.
This function is created for various drivers to simplify handling of
their buffers.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently vb2 core acquires mmap_sem just around call to
__qbuf_userptr(). However since commit f035eb4e97 (videobuf2: fix
lockdep warning) it isn't necessary to acquire it so early as we no
longer have to drop queue mutex before acquiring mmap_sem. So push
acquisition of mmap_sem down into .get_userptr memop so that the
semaphore is acquired for a shorter time and it is clearer what it is
needed for.
Note that we also need mmap_sem in .put_userptr memop since that ends up
calling vb2_put_vma() which calls vma->vm_ops->close() which should be
called with mmap_sem held. However we didn't hold mmap_sem in some code
paths anyway (e.g. when called via vb2_ioctl_reqbufs() ->
__vb2_queue_free() -> vb2_dma_sg_put_userptr()) and getting mmap_sem in
put_userptr() introduces a lock inversion with queue->mmap_lock in the
above mentioned call path.
Luckily this whole locking mess will get resolved once we convert
videobuf2 core to the new mm helper which avoids the need for mmap_sem
in .put_userptr memop altogether.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
sr030pc30_get_fmt() can only succeed if both info->curr_win and
info->curr_fmt are not NULL.
If one of those vars are null, the curent code would call:
ret = sr030pc30_set_params(sd);
If the curr_win is null, it will return -EINVAL, as it would be
expected. However, if curr_fmt is NULL, the function won't
set it.
The code will then try to read from it:
mf->code = info->curr_fmt->code;
mf->colorspace = info->curr_fmt->colorspace;
with obviouly won't work.
This got reported by smatch:
drivers/media/i2c/sr030pc30.c:505 sr030pc30_get_fmt() error: we previously assumed 'info->curr_win' could be null (see line 499)
drivers/media/i2c/sr030pc30.c:507 sr030pc30_get_fmt() error: we previously assumed 'info->curr_fmt' could be null (see line 499)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Why to store the chosed values for prediv, postdiv and mult if
those won't be used?
drivers/media/i2c/ov2659.c: In function 'ov2659_pll_calc_params':
drivers/media/i2c/ov2659.c:912:35: warning: variable 's_mult' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:20: warning: variable 's_postdiv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:6: warning: variable 's_prediv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
This is likely some leftover from some past change.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/tc358743.c:148:19: warning: Variable length array is used.
As the maximum size is 1026, we can't use dynamic var, as it
would otherwise spend 1056 bytes of the stack at i2c_wr() function.
So, allocate a buffer with the allowed maximum size together with
the state var.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 4c21b8fd8f ("MIPS: seccomp: Handle indirect system calls (o32)")
fixed indirect system calls on O32 but it also introduced a bug for MIPS64
where it erroneously modified the v0 (syscall) register with the assumption
that the sycall offset hasn't been taken into consideration. This breaks
seccomp on MIPS64 n64 and n32 ABIs. We fix this by replacing the addition
with a move instruction.
Fixes: 4c21b8fd8f ("MIPS: seccomp: Handle indirect system calls (o32)")
Cc: <stable@vger.kernel.org> # 3.15+
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently the driver disable power management on all low-latency
interfaces, while it should disable it on WiDi interfaces only.
Non-P2P interfaces that runs voice and video traffic should enable
power management.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TDLS support is declared by the FW, set the bit indicating wider-BW
support as well.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The &mvm->tof_data.range_req.ap[] array has IWL_MVM_TOF_MAX_APS elements
so the check should be >= instead of >. Also the test can underflow so
I have changed "i" to unsigned.
Fixes: ce7929186a ('wlwifi: mvm: add basic Time of Flight (802.11mc FTM) support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to use hex_dump_to_buffer() in the cases like this:
hexdump_to_buffer(buf, len, 16, 1, outbuf, outlen, false); /* len <= 16 */
sprintf("%s\n", outbuf);
since it maybe easily converted to simple:
sprintf("%*ph\n", len, buf);
Note: it seems in one case the output is groupped by 2 bytes and looks like a
typo. Thus, patch changes that to plain byte stream.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The mac80211 patch to pass the NAPI struct only changed iwlwifi to
store the NAPI struct, but we can do better: pass it directly from
the lower transport layer to the opmode during RX, and then on to
mac80211 from there.
When we add multiple RX queues, we can then pass the appropriate
NAPI struct properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' into next
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
Lmac sched scan supports partial scans, so we can set some channels to be
scanned on every scan iteration and others to be scanned only on some
iterations. Currently we set all channels to be scanned every iteration,
but still have some configuration of which iterations should be partial
and which should be full.
Remove all partial/full scan configuration to reduce confusions.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove timing values from iwl_mvm_scan_params and use defines and
arrays of values instead.
While at that fix few values and corner cases and align all OSs
to ChromeOS values.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We added calls to d3_suspend/resume trans ops during the
suspend/resume flow.
However, the wrapper code didn't verify the trans ops were
actually defined, resulting in panic when they were not
(such as in the case of sdio trans)
Fixes: 6dfb36c89d ("iwlwifi: call d3_suspend/resume in d0i3 case as well")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The M-Audio Transit exposes an interface with a SYNC_NONE attribute.
This is not a valid value according to the USB audio classspec. However
there is a sync endpoint associated to this record. Changing the logic to
try to use this sync endpoint allows for seamless transitions between
altset 2 and altset 3. If any errors happen, the behavior remains the same.
$ more /proc/asound/card1/stream0
M-Audio Transit USB at usb-0000:00:14.0-2, full speed : USB Audio
Playback:
Status: Stop
Interface 1
Altset 1
Format: S24_3LE
Channels: 2
Endpoint: 3 OUT (ADAPTIVE)
Rates: 48001 - 96000 (continuous)
Interface 1
Altset 2
Format: S24_3LE
Channels: 2
Endpoint: 3 OUT (NONE)
Rates: 8000 - 48000 (continuous)
Interface 1
Altset 3
Format: S16_LE
Channels: 2
Endpoint: 3 OUT (ASYNC)
Rates: 8000 - 48000 (continuous)
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a transition occurs between alternate settings that do not use the
same synchronization method, the substream pointers were not reset.
This prevents audio from being played during the second transition.
Identified and tested with M-Audio Transit device
(0763:2006 Midiman M-Audio Transit)
Details of the issue:
First playback to adaptive endpoint:
$ aplay -Dhw:1,0 ~/24_96.wav
Playing WAVE '/home/plb/24_96.wav' : Signed 24 bit Little Endian in 3bytes,
Rate 96000 Hz, Stereo
[ 3169.297556] usb 1-2: setting usb interface 1:1
[ 3169.297568] usb 1-2: Creating new playback data endpoint #3
[ 3169.298563] usb 1-2: Setting params for ep #3 (type 0, 3 urbs), ret=0
[ 3169.298574] usb 1-2: Starting data EP @ffff880035fc8000
first playback to asynchronous endpoint:
$ aplay -Dhw:1,0 ~/16_48.wav
Playing WAVE '/home/plb/16_48.wav' : Signed 16 bit Little Endian,
Rate 48000 Hz, Stereo
[ 3204.520251] usb 1-2: setting usb interface 1:3
[ 3204.520264] usb 1-2: Creating new playback data endpoint #3
[ 3204.520272] usb 1-2: Creating new capture sync endpoint #83
[ 3204.521162] usb 1-2: Setting params for ep #3 (type 0, 4 urbs), ret=0
[ 3204.521177] usb 1-2: Setting params for ep #83 (type 1, 4 urbs), ret=0
[ 3204.521182] usb 1-2: Starting data EP @ffff880035fce000
[ 3204.521204] usb 1-2: Starting sync EP @ffff8800bd616000
second playback to adaptive endpoint: no audio and error on terminal:
$ aplay -Dhw:1,0 ~/24_96.wav
Playing WAVE '/home/plb/24_96.wav' : Signed 24 bit Little Endian in 3bytes,
Rate 96000 Hz, Stereo
aplay: pcm_write:1939: write error: Input/output error
[ 3239.483589] usb 1-2: setting usb interface 1:1
[ 3239.483601] usb 1-2: Re-using EP 3 in iface 1,1 @ffff880035fc8000
[ 3239.484590] usb 1-2: Setting params for ep #3 (type 0, 4 urbs), ret=0
[ 3239.484606] usb 1-2: Setting params for ep #83 (type 1, 4 urbs), ret=0
This last line shows that a sync endpoint is used when it shouldn't.
The sync endpoint is no longer valid and the pointers are corrupted
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The struct exynos_drm_gem_obj can have fields of the struct
exynos_drm_gem_buf then don't need to use exynos_drm_buf.c file.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The dma-buf codes of exynos drm is almost same with prime helpers. A
difference is that consider DMA_NONE when import dma-buf, but it's wrong
and we don't consider it any more, so we can use prime interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function roundup_gem_size can be merged in exynos_drm_gem_create.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function update_vm_cache_attr can be merged in exynos_drm_gem_mmap.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The function check_gem_flags is too simple, so it's better to move codes
in each consumer functions.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The userptr, write and pfnmap of struct exynos_drm_gem_buf are not used
anywhere.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already struct exynos_drm_gem_buf has pages of the buffer, so we don't
need to copy from sg table of the buffer to sg table of dma-buf
attachment, just can make sg table from pages of the buffer.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The exynos_drm_gem_map_buf can be merged in exynos_drm_gem_fault.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no reason to use mutex locking in pagefault handler.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The convert_to_vm_err_msg is called just once by exynos_drm_gem_fault,
so it's simple not to use the function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Already struct exynos_drm_gem_buf has pages of the buffer when buffer is
created, so just can use pages in page fault handler, we don't have to
make sgtable of the buffer. But this needs to construct pages of the
buffer that is imported from dma-buf prime.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Skylake Client CPU idle Power states (C-states)
are similar to the previous generation, Broadwell.
However, Skylake does get its own table with updated
worst-case latency and average energy-break-even residency values.
Signed-off-by: Len Brown <len.brown@intel.com>
struct exynos_drm_encoder was justing wrapping struct drm_encoder, it had
only a drm_encoder member and the internal exynos_drm_encoders ops that
was directly mapped to the drm_encoder helper funcs.
So now exynos DRM uses struct drm_encoder directly, this removes
completely the struct exynos_drm_encoder.
v2: add empty .mode_fixup() and .mode_set() to DSI and DPI to avoid null
pointer.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
As we are removing the exynos encoder move the encoder setup operation
directly inside the exynos_drm_load()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This functions was just hiding the encoder and connector creation in
a way that was less clean than if we get rid of it. For example,
exynos_encoder ops had .create_connector() defined only because we were
handing off the encoder and connector creation to
exynos_drm_create_enc_conn(). Without this function we can directly call
the create_connector function internally in the code, without the need of
any vtable access.
It also does some refactoring in the code like creating a bind function
for dpi devices.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
