The zero-length packet is the sendor tells the receiver that there
is no more data, so it is only needed at the TX side.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The system configuration API should be called before the controller
run, otherwise, undefined results may occur. So, we override hcd
reset API, and add system configuration API after controller reset.
Cc: Li Jun <peter.chen@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
If usbmisc hasn't probed yet, defer the probe.
It's not enough to check if the platform device for the OF node of the
usbmisc has been registered, but it also needs to have been probed
already before we can call imx_usbmisc_init().
This can happen if the order in which devices are probed change due to
async probing or on-demand probing of dependencies.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
This makes the function hw_alloc_repmap be declared to have a return
type of void now due to this particular function never returning
a error code to its caller due to this function always running
successfully to completion nor it's caller putting the return
value into a variable in order to check if a error code is passed
from the function hw_alloc_repmap when calling this function.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
The struct ci_hdrc is the drvdata for hcd device, so we don't
need to introduce extra ci_hdrc structure for ehci.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
It is used to configure controller parameters according to
platform data, like speed, stream mode, etc, both host and
device's initialization need it, most of code are the
same for both roles, with this new interface, it can reduce
the duplicated code and be easy to maintain in future.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
We can support USB OTG 1.3 USB_DEVICE_A_HNP_SUPPORT request when
the driver supports OTG FSM mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
For i.mx platform, set ttctrl.ttha with non-zero value only affects
sitd, and ehci core makes sure the schedule is not full when accepts
new request, so it will not occur the transaction which will acorss
the SoF.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Two small bug fixes for the code you pulled for 4.3:
- Used a SHIFT define instead of a MASK define to check if a bit is turned on
when destroying hqd. Luckily, this is in gfx7 interface file with amdgpu,
which was used only for bring-up purposes of amdgpu, so no real effect on
a running system
- Used a logical AND instead of a bitwise AND operator, when initializing
sdma virtual memory when using SDMA queues
* tag 'drm-amdkfd-next-fixes-2015-08-05' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: fix bug when initializing sdma vm
drm/amdgpu: fix bug when amdkfd destroys hqd
This serie of patches fix minor bugs around how driver sub-components are
bind and planes z-ordering.
The main part is about atomic support: using more atomic helpers allow us
to simplify the code (~300 lines removed) and to ahve a better match between
drm concepts (planes and crtc) and hardware split.
[airlied: fixed up conflict in atomic code]
* 'drm-sti-next-atomic-2015-08-11' of http://git.linaro.org/people/benjamin.gaignard/kernel:
drm/sti: atomic crtc/plane update
drm/sti: rename files and functions
drm/sti: code clean up
drm/sti: fix dynamic z-ordering
drm: sti: fix sub-components bind
The recent refactoring of the IGMP and MLD parsing code into
ipv6_mc_check_mld() / ip_mc_check_igmp() introduced a potential crash /
BUG() invocation for bridges:
I wrongly assumed that skb_get() could be used as a simple reference
counter for an skb which is not the case. skb_get() bears additional
semantics, a user count. This leads to a BUG() invocation in
pskb_expand_head() / kernel panic if pskb_may_pull() is called on an skb
with a user count greater than one - unfortunately the refactoring did
just that.
Fixing this by removing the skb_get() call and changing the API: The
caller of ipv6_mc_check_mld() / ip_mc_check_igmp() now needs to
additionally check whether the returned skb_trimmed is a clone.
Fixes: 9afd85c9e4 ("net: Export IGMP/MLD message validation code")
Reported-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rocker driver tracks arp_tbl neighs to resolve IPv4 route nexthops. The
driver uses NETEVENT_NEIGH_UPDATE for neigh adds and updates, but there is
no event when the neigh is removed from the device (such as when the device
goes admin down). This patches hooks ndo_neigh_destroy so the driver can
know when a neigh is removed from the device. In response, the driver will
purge the neigh entry from its internal tbl.
I didn't find an in-tree users of ndo_neigh_destroy, so I'm not sure if
this ndo is vestigial or if there are out-of-tree users. In any case, it
does what I need here. An alternative design would be to generate
NETEVENT_NEIGH_UPDATE event when neigh is being destroyed, setting state to
NUD_NONE so driver knows neigh entry is dead.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sucessful probe, driver prints the switch ID. This patch changes the
format of the printed ID to match what's used in sysfs phys_switch_id node.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix minor typo so that can pass correct pointer variable for
container_of().
Signed-off-by: Leo Yan <leo.yan@linaro.org>
[jc: tweaked formatting]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Final drm-misc pull for 4.3:
- fbdev emulation Kconfig option for everyone thanks to Archit. It's not
everything yet bit this is fairly tricky since it spawns all drivers.
- vgaarb & vgaswitcheroo polish from Thierry
- some drm_irq.c cleanups (Thierry)
- struct_mutex crusade from me
- more fbdev panic handling removal
- various things all over in drm core&helpers
* tag 'topic/drm-misc-2015-08-13' of git://anongit.freedesktop.org/drm-intel: (65 commits)
drm/atomic: Use KMS VBLANK API
drm/irq: Document return values more consistently
drm/irq: Make pipe unsigned and name consistent
drm/irq: Check for valid VBLANK before dereference
drm/irq: Remove negative CRTC index special-case
drm/plane: Remove redundant extern
drm/plane: Use consistent data types for format count
vga_switcheroo: Remove unnecessary checks
vga_switcheroo: Wrap overly long lines
vga_switcheroo: Use pr_fmt()
vga_switcheroo: Cleanup header comment
vga_switcheroo: Use pr_*() instead of printk()
vgaarb: Fix a few checkpatch errors and warnings
vgaarb: Use vgaarb: prefix consistently in messages
vgaarb: Stop complaining about absent devices
drm/atomic: fix null pointer access to mode_fixup callback
drm/i915: Use CONFIG_DRM_FBDEV_EMULATION
drm/core: Set mode to NULL when connectors in a set drops to 0.
drm/atomic: Call ww_acquire_done after check phase is complete
drm/atomic: Paper over locking WARN in default_state_clear
...
Jeremy Linton says:
====================
Enable smsc911x for use with ACPI
This set of patches enables the front Ethernet port on the
ARM Juno development platform when used with an ACPI enabled kernel.
These patches covert the of_property* calls in the driver to the
DT/ACPI agnostic device_property* calls, and add the arm hardware
id to the acpi_match_table.
To support the above changes I copied a couple routines from
of_net into the properties.c file, and modified them to
be ACPI/DT agnostic. I'm not 100% sure this is the correct location
for these functions. But I think they are required to avoid having
a dozen different implementations scattered across assorted Ethernet
adapters that are being enabled to use ACPI properties.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACPI bindings for the smsc911x driver. Convert the DT specific calls
to nonspecific device* calls, This allows the driver to work
with both ACPI and DT configurations. Ethernet should now work when using
ACPI on ARM Juno.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
OF has some helper functions for parsing MAC and PHY settings.
In cases where the platform is providing this information rather
than the device itself, there needs to be similar functions for ACPI.
These functions are slightly modified versions of the ones in
of_net which can use information provided via DT or ACPI.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a document describing the process of adding a new system call,
including the need for a flags argument for future compatibility, and
covering 32-bit/64-bit concerns (albeit in an x86-centric way).
Signed-off-by: David Drysdale <drysdale@google.com>
Reviewed-by: Michael Kerrisk <mtk.manpages@gmail.com>
Reviewed-by: Eric B Munson <emunson@akamai.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Yuchung Cheng says:
====================
minor tail loss probe improvements
This patch series enhance the tail loss probe (TLP) on some error
conditions. When TLP fails to send a probe, it will no longer
extend the RTO. When it fails to send a new packet because of
receiver window limit, it'll try to retransmit the last packet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When TLP fails to send new packet because of receive window
limit, it should fall back to retransmit the last packet instead.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TLP was unable to send a probe, it extended the RTO to
now + icsk_rto. But extending the RTO makes little sense
if no TLP probe went out. With this commit, instead of
extending the RTO we re-arm it relative to the transmit time
of the write queue head.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mugunthan V N says:
====================
Add AM335x PG1.0 CPSW errata workaround
With commit 870915feab ("drivers: net: cpsw: remove
disable_irq/enable_irq as irq can be masked from cpsw itself"),
CPSW on AM335x beagle bone white is broken as there is a errata
for AM335x PG1.0. This patch series implements the workaround by
disabling the interrupts from ARM IRQ controller for AM335x SoC
in addition to the masking of interrupts in CPSW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver has been updated with compatibles for enabling errata
workarounds. So updating cpsw compatibles.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver has been updated with compatibles for enabling errata
workarounds. So updating cpsw compatibles.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Am335x Errata [1] Advisory 1.0.9, The CPSW C0_TX_PEND and
C0_RX_PEND interrupt outputs provide a single transmit interrupt
that combines transmit channel interrupts TXPEND[7:0] and a
single receive interrupt that combines receive channel interrupts
RXPEND[7:0]. The TXPEND[0] and RXPEND[0] interrupt outputs are
connected to the ARM Cortex-A8 interrupt controller (INTC) rather
than the C0_TX_PEND and C0_RX_PEND interrupt outputs. So even
though CPSW interrupt is cleared by writing appropriate values to
EOI register the interrupt is not cleared in IRQ controller. So
interrupt is still pending and CPU is struck in ISR, the
workaround is to disable the interrupts in ARM irq controller.
[1] http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1addc12648
This commit seems to cause crashes in gk104_fifo_intr_runlist() by
returning 0xbad0da00 when register 0x2a00 is read. Since this commit was
intended for GM20B which is not completely supported yet, let's revert
it for the time being.
Reported-by: Eric Biggers <ebiggers3@gmail.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This addresses two issues that cause problems with viewperf maya-03 in
situation with memory pressure.
The first issue causes attempts to unreserve buffers if batched
reservation fails due to, for example, a signal pending. While previously
the ttm_eu api was resistant against this type of error, it is no longer
and the lockdep code will complain about attempting to unreserve buffers
that are not reserved. The issue is resolved by avoid calling
ttm_eu_backoff_reservation in the buffer reserve error path.
The second issue is that the binding_mutex may be held when user-space
fence objects are created and hence during memory reclaims. This may cause
recursive attempts to grab the binding mutex. The issue is resolved by not
holding the binding mutex across fence creation and submission.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are some workqueue functions declared in workqueue.h, so include
that in the workqueue section of the DocBook docs.
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Pull ARM fixes from Russell King:
"Another few small ARM fixes, mostly addressing some VDSO issues"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8410/1: VDSO: fix coarse clock monotonicity regression
ARM: 8409/1: Mark ret_fast_syscall as a function
ARM: 8408/1: Fix the secondary_startup function in Big Endian case
ARM: 8405/1: VDSO: fix regression with toolchains lacking ld.bfd executable
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3f5159a922 ("x86/asm/entry/32: Update -ENOSYS handling to match
the 64-bit logic") broke the ENOSYS handling for the 32-bit compat case.
The proper error return value was never loaded into %rax, except if
things just happened to go through the audit paths, which ended up
reloading the return value.
This moves the loading or %rax into the normal system call path, just to
make sure the error case triggers it. It's kind of sad, since it adds a
useless instruction to reload the register to the fast path, but it's
not like that single load from the stack is going to be noticeable.
Reported-by: David Drysdale <drysdale@google.com>
Tested-by: Kees Cook <keescook@chromium.org>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flags are now mandatory for devm_gpiod_get(). So let's use proper flag
to configure gpio for output instead of doing this by hand.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[Dmitry: GPIOD_ASIS -> GPIOD_OUT_LOW]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove pci_ats_enabled(). There are no callers outside the ATS code
itself. We don't need to check ats_cap, because if we don't find an ATS
capability, we'll never set ats_enabled.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Stop caching the Invalidate Queue Depth in struct pci_dev.
pci_ats_queue_depth() is typically called only once per device, and it
returns a fixed value per-device, so callers who need the value frequently
can cache it themselves.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Move ATS declarations to linux/pci.h so they're all in one place.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
There's no need to BUG() if we enable ATS when it's already enabled. We
don't need to BUG() when disabling ATS on a device that doesn't support ATS
or if it's already disabled. If ATS is enabled, certainly we found an ATS
capability in the past, so it should still be there now.
Clean up these error paths.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Use the pci_physfn() helper rather than looking up physfn by hand.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The ATS setup code in ats_alloc_one() is only used by pci_ats_init(), so
inline it there. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
We previously returned -ENODEV for devices that don't support ATS (except
that we always returned 0 for VFs, whether or not they support ATS).
For consistency, always return -EINVAL (not -ENODEV) if the device doesn't
support ATS. Return zero for VFs that support ATS.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The extended capabilities list is linked with 12-bit pointers, and the ATS
Smallest Translation Unit and Invalidate Queue Depth fields are both 5
bits.
Use u16 and u8 to hold the extended capability address and the stu and qdep
values. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The pci_ats struct is small and will get smaller, so I don't think it's
worth allocating it separately from the pci_dev struct.
Embed the ATS fields directly into struct pci_dev.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Previously, we allocated pci_ats structures when an IOMMU driver called
pci_enable_ats(). An SR-IOV VF shares the STU setting with its PF, so when
enabling ATS on the VF, we allocated a pci_ats struct for the PF if it
didn't already have one. We held the sriov->lock to serialize threads
concurrently enabling ATS on several VFS so only one would allocate the PF
pci_ats.
Gregor reported a deadlock here:
pci_enable_sriov
sriov_enable
virtfn_add
mutex_lock(dev->sriov->lock) # acquire sriov->lock
pci_device_add
device_add
BUS_NOTIFY_ADD_DEVICE notifier chain
iommu_bus_notifier
amd_iommu_add_device # iommu_ops.add_device
init_iommu_group
iommu_group_get_for_dev
iommu_group_add_device
__iommu_attach_device
amd_iommu_attach_device # iommu_ops.attach_device
attach_device
pci_enable_ats
mutex_lock(dev->sriov->lock) # deadlock
There's no reason to delay allocating the pci_ats struct, and if we
allocate it for each device at enumeration-time, there's no need for
locking in pci_enable_ats().
Allocate pci_ats struct during enumeration, when we initialize other
capabilities.
Note that this implementation requires ATS to be enabled on the PF first,
before on any of the VFs because the PF controls the STU for all the VFs.
Link: http://permalink.gmane.org/gmane.linux.kernel.iommu/9433
Reported-by: Gregor Dick <gdick@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
metadata snapshots aren't widely used but help provide a consistent
view of the metadata associated with an active thin-pool.
- a dm-cache fix for the 4.2 "default" policy switch from "mq" to "smq"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVzPl/AAoJEMUj8QotnQNa2MUH/24BKs8WYNy79B9pr6H41ouQ
LAXFVfx3Vy7n3U1KrZcPylXb7R0feXphUrSXJ6ZlKz/Df+AhG5ycUOCfSZxSDpA9
pX5rtWFSWLXGF3wRf0GXqB3CXkrMKlNWVAUlzge39TpIzpdkbh9reM9He4yQphl9
u0QVvIOTQsUrtN9htnQb7Dgmm7qD6NinrebOrWTiOqBdCh3Iw4J48RsYggYOG0ZP
fbMnpZlH537vgLyKaz72Xh+kMrYmP5DBd1f+iAUBVKk12HQVQNMzEwOgkEB0M+4l
EG3c4O3zMVrBxXdxsI2srFZfLX2XeUYAuMx8cfVSSCDEzQwjC0kmXVdkCYuAjAk=
=r/53
-----END PGP SIGNATURE-----
Merge tag 'dm-4.2-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- two stable fixes for corruption seen in a snapshot of thinp metadata;
metadata snapshots aren't widely used but help provide a consistent
view of the metadata associated with an active thin-pool.
- a dm-cache fix for the 4.2 "default" policy switch from "mq" to "smq"
* tag 'dm-4.2-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache policy smq: move 'dm-cache-default' module alias to SMQ
dm btree: add ref counting ops for the leaves of top level btrees
dm thin metadata: delete btrees when releasing metadata snapshot
