Setup pin muxing and properties for the debug console on uart0.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Hook up LEDs on the outputs from the D-type flip-flop found on
the address/data bus.
Note that the LEDx label in the schematics is reversed in regard
to the bits on the data bus. Hence the reverse ordering used here.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Setup the emc pins used by external memory devices and add
configuration for the devices found on the EA4357 devkit.
The EA4357 devkit has a NOR Flash attached to chip select 0
and a D-type flip-flop used for LEDs on chip select 2.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enable USB0 on the EA4357 devkit and setup the required USB0
control pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
All devices in the LPC18xx/43xx familiy contain a ARM PL172
MultiPort Memory Controller (MPMC).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
NXP LPC185x and LPC435x/70 devices contain a ARM PL111 lcd controller.
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the USB OTG phy under the CREG syscon node and attach it to
the USB0 EHCI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
get_maintainers.pl would list linux-arm-kernel for most bcm2835
changes because it's under arch/arm, but might not for other bcm2835
drivers. Most ARM architectures appear to list linux-arm-kernel as an
appropriate list as well.
Signed-off-by: Eric Anholt <eric@anholt.net>
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The current maintainers have limited free time to work on the
architecture, and I'm motivated to do so for my work on graphics for
Broadcom. Arnd and Florian suggested to me that this might be the way
forward.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
*) Fix compiler error when sun4i usb phy driver is built as module
*) Fix SATA Lockup issue in dra7 SoC
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=j6wu
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.2-rc6
*) Fix compiler error when sun4i usb phy driver is built as module
*) Fix SATA Lockup issue in dra7 SoC
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The PMU device contains an interrupt controller, power control and
resets. The interrupt controller is a little sub-standard in that
there is no race free way to clear down pending interrupts, so we try
to avoid problems by reducing the window as much as possible, and
clearing as infrequently as possible.
The interrupt support is implemented using an IRQ domain, and the
parent interrupt referenced in the standard DT way.
The power domains and reset support is closely related - there is a
defined sequence for powering down a domain which is tightly coupled
with asserting the reset. Hence, it makes sense to group these two
together, and in order to avoid any locking contention disrupting this
sequence, we avoid the use of syscon or regmap.
This patch adds the core PMU driver: power domains must be defined in
the DT file in order to make use of them. The reset controller can
be referenced in the standard way for reset controllers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the description of the GPU power domain to the PMU DT entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the description of the video decoder power domain to the PMU DT
entry.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Now that we have a PMU driver, we can wire up the RTC interrupt in the
DT description for Dove.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the PMU node, and move the child devices of the PMU node beneath
this new node, giving it a "simple-bus" so that the OF platform
device creator will create these child devices. No functional change
from this is expected.
The PMU provides multiple features, including an interrupt, reset,
power and isolation controller.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patchkit adds the ability to turn off time stamps per event.
One usaful case for partial time is to work with per-event callgraph to
enable "PEBS threshold > 1" (https://lkml.org/lkml/2015/5/10/196), which
can significantly reduce the sampling overhead.
The event samples with time stamps off will not be ordered.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1438677022-34296-2-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVwhncAAoJEL/70l94x66Dy7IIAJXfraikJQ9ghhLhjrP+5f5H
MNBL+e3jKGmGVgItrtOMcLlJJvPkFNBkFMmYRJtdawezu46eFBLnIoTp8ZcG6cvu
5Gjs1PNfq1nP5IzWsYYbohlaf1xkij+Jm2JZ/fxuEGC6xM91WVGV7YENt87S7O16
ZdfhhEFHTTe+Fg86QwDGZ2bOhTBwZEAaVFM6siCml/WiqYtecwzEn19OiP6XeVbO
FczG7CUXumrPnEohYrAVrCtIIb5dGzUCstQGlo3bC7CJ/G6CjaBl4cSd6Y/BHkhD
KV6M7VJxjJ84HAKy9PMhC2iPC7H7Vfjg1iq6czHWu/Tida0d6dBiVzLVKcz2jj4=
=SYMM
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Just two very small & simple patches"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MTRR: Use default type for non-MTRR-covered gfn before WARN_ON
KVM: s390: Fix hang VCPU hang/loop regression
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
CPU fan speed going up and down on Dell Studio XPS 8100 for
unknown reasons. Without further debugging on the affected
machine, it is not possible to find the problem.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100121
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Jan C Peters <jcpeters89@gmail.com>
Cc: stable@vger.kernel.org # v4.0+, will need backport
[groeck: cleaned up description, comments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Merge "ARM: Interrupt cleanups and API change preparation" from Thomas
Gleixner:
The following patch series contains the following changes:
- Consolidation of chained interrupt handler setup/removal
- Switch to functions which avoid a redundant interrupt
descriptor lookup
- Preparation of interrupt flow handlers for the 'irq' argument
removal
* 'queue/irq/arm' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ARM/orion/gpio: Prepare gpio_irq_handler for irq argument removal
ARM/pxa: Prepare balloon3_irq_handler for irq argument removal
ARM/pxa: Prepare *_irq_handler for irq argument removal
ARM/dove: Prepare pmu_irq_handler for irq argument removal
ARM/sa1111: Prepare sa1111_irq_handler for irq argument removal
ARM/locomo: Prepare locomo_handler for irq argument removal
ARM, irq: Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc
ARM/LPC32xx: Use irq_set_handler_locked()
ARM/irq: Use access helper irq_data_get_affinity_mask()
ARM/locomo: Consolidate chained IRQ handler install/remove
ARM/orion: Consolidate chained IRQ handler install/remove
Signed-off-by: Olof Johansson <olof@lixom.net>
As reported by the 0-Day testing service:
kernel/auditfilter.c: In function 'audit_rule_change':
>> kernel/auditfilter.c:864:6: warning: 'err' may be used uninit...
int err;
Cc: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
To avoid meeting garbage data in next free node block at the end of warm
node chain when doing recovery, we will try to zero out that invalid block.
If the device is not support discard, our way for zeroing out block is:
grabbing a temporary zeroed page in meta inode, then, issue write request
with this page.
But, we forget to release that temporary page, so our memory usage will
increase without gaining any hit ratio benefit, so it's better to free it
for saving memory.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In following call path, we will pass a locked and referenced ipage
pointer to get_new_data_page:
- init_inode_metadata
- make_empty_dir
- get_new_data_page
There are two exit paths in get_new_data_page when error occurs:
1) grab_cache_page fails, ipage will not be released;
2) f2fs_reserve_block fails, ipage will be released in callee.
So, it's not consistent for error handling in get_new_data_page.
For f2fs_reserve_block, it's not very easy to change the rule
of error handling, since it's already complicated.
Here we deside to choose an easy way to fix this issue:
If any error occur in get_new_data_page, we will ensure releasing
ipage in this function.
The same issue is in f2fs_convert_inline_dir, fix that too.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Replace BUG_ON with f2fs_bug_on to deal with
block and segment validity check failed.
Signed-off-by: Xue Liu <liuxueliu.liu@huawei.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In get_meta_page, we guarantee no failure for the returned page,
but sometimes, IO error from device will incur returning an
non-updated page.
Then, we still use this page as updated one, exception could happen
when using this kind of page.
So in this condition, we'd better freeze fs by making fs readonly and
and stop doing checkpoint.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
some backing devices need pages to be stable during writeback. It doesn't
matter if
the page is completely overwritten or already uptodate, it needs to wait
before write.
Signed-off-by: Fan li <fanofcode.li@samsung.com>
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds to handle error cases in commit_inmem_pages.
If an error occurs, it stops to write the pages and return the error right
away.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When there is no enough free nids in free nid cache, we will try to
readahead FREE_NID_PAGES:4 nat pages into page cache of meta_inode,
then, reading nat entries in nat page for adding free nids to free nid
cache.
But when traversing all nat pages we readaheaded in a circulation,
our exit condition is not set right, one more nat page will be scanned
without readaheading, resulting worse read performance.
This patch fixes to read the correct number nat pages to avoid bad
performance.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If we clear inline data/dentry flag in handle_failed_inode, we will fail
to decline the stat count of inline data/dentry in f2fs_evict_inode due
to no flag in inode. So remove the wrong clearing.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In f2fs_ioc_start_{atomic,volatile}_write, if we failed in converting
inline data, we will report error to user, but still remain atomic/volatile
flag in inode, it will impact further writes for this file. Fix it.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch fixes the incorrect range (0, LONG_MAX) which is used
in ranged fsync. If we use LONG_MAX as the parameter for indicating
the end of file we want to synchronize, in 32-bits architecture
machine, these datas after 4GB offset may not be persisted in
storage after ->fsync returned.
Here, we alter LONG_MAX to LLONG_MAX to fix this issue.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
When flushing comes from background, if there is no dirty page in the
mapping of inode, we'd better to skip seeking dirty page from mapping
for writebacking.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
The if statement "goto continue_unlock" is exactly the same when
each if condition is true that is depended on the value of both
"step" and "is_cold_data(page)" are 0 or 1. That means when the
value of "step" equals to "is_cold_data(page)", the if condition
is true and the if statement "goto continue_unlock" appears only
once, so it can be optimized to reduce the duplicated code.
Signed-off-by: Tiezhu Yang <kernelpatch@126.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In handle_failed_inode, there is a potential deadlock which can happen
in below call path:
- f2fs_create
- f2fs_lock_op down_read(cp_rwsem)
- f2fs_add_link
- __f2fs_add_link
- init_inode_metadata
- f2fs_init_security failed
- truncate_blocks failed
- handle_failed_inode
- f2fs_truncate
- truncate_blocks(..,true)
- write_checkpoint
- block_operations
- f2fs_lock_all down_write(cp_rwsem)
- f2fs_lock_op down_read(cp_rwsem)
So in this path, we pass parameter to f2fs_truncate to make sure
cp_rwsem in truncate_blocks will not be locked again.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
In f2fs_do_collapse, region cp_rwsem covered is large, since it will be
held until all blocks are left shifted, so if we try to collapse small
area at the beginning of large file, checkpoint who want to grab writer's
lock of cp_rwsem will be delayed for long time.
In order to avoid this condition, altering to lock/unlock cp_rwsem each
shift operation.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Add a lookup and a insertion interface for extent tree.
The new lookup return the insert position and the prev/next
extents closest to the offset we lookup when find no match.
The new insertion uses above parameters to improve performance.
There are three possible insertions after the lookup in
f2fs_update_extent_tree, two of them insert parts of removed extent
back to tree, since no merge happens during this process, new insertion
skips the merge check in this scanario; the another insertion inserts a
new extent to tree, new insertion uses prev/next extent and insert
position to insert this extent directly, and save the time of searching
down the tree.
As long as tree remains unchanged between lookup and insertion, this
would work fine. And the new lookup would be useful when add
multi-blocks extent support for insertion interface.
Signed-off-by: Fan li <fanofcode.li@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch changes for a caller to handle the page after its bio gets an error.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Variables for recording extent cache ratio info were updated without
protection, this patch tries to alter them to atomic_t type for more
accurate stat.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch adds to stat the number of inline xattr inode for
showing in debugfs.
Signed-off-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
That encrypted page is used temporarily, so we don't need to mark it accessed.
Reviewed-by: Chao Yu <chao2.yu@samsung.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Update the aoa-soundbus framework to use dev_pm_ops rather than the
deprecated legacy suspend and resume callbacks.
Since there isn't anything special to do at the bus level the bus driver
does not have to implement any callbacks. The device driver core will
automatically pick up and execute the device's PM ops.
As there is only a single aoa-soundbus driver implementing suspend and
resume, update both the core and driver at the same time to avoid
unnecessary code churn.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Nand controller often share some pins with sd/mmc controller on
atlas and prima series, nand node can be disabled if the pins are
used by sd/mmc controller.
Signed-off-by: Huayi Li <huayi.li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds SDR(software digital raio) nodes and the DMA channels
for it.
Signed-off-by: Yonghui Zhang <yonghui.zhang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds lost PWM node, and also fixes the ranges of its
parent node.
Signed-off-by: Guo Zeng <guo.zeng@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds lost G2D node, and also fixes the range of its
parent node.
Signed-off-by: Dongli Li <Kasin.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
this patch adds multimedia video codec node, and also fixes the
ranges of its parent node.
Signed-off-by: Xiaofeng Fei <xiaofeng.fei@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
spi framework can use alias name of spi device to retrieve the bus id,
so bus id will not be dynamical but statical and it will be easier for
test for a specified spi device with a fixed name like use spidev.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
