Pull s390 fixes from Martin Schwidefsky:
"Two bug fixes:
- fix a crash on pre-z10 hardware due to cache-info
- fix an issue with classic BPF programs in the eBPF JIT"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/cachinfo: add missing facility check to init_cache_level()
s390/bpf: clear correct BPF accumulator register
This resulted in the use of polling mode when other approaches
(dma or interrupts) would have been more appropriate.
Happened for transfers longer than 477 bytes.
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using reverse polarity for clock (spi-cpol) on a device
the clock line gets altered after chip-select has been asserted
resulting in an additional clock beat, which confuses hardware.
This did not show when using native-CS, as the same register
is used to control cs as well as polarity, so the changes came
into effect at the same time. Unfortunately this is not true
with gpio-cs.
To avoid this situation this patch moves the setup of polarity
(spi-cpol and spi-cpha) outside of the chip-select into
prepare_message, which is run prior to asserting chip-select.
Also fixes resetting 3-wire mode after use of rx-mode, so that
a 3-Wire sequence TX, RX, TX works as well (right now it runs
TX, RX, RX instead)
Reported-by: Noralf Tronnes <noralf@tronnes.org>
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since keypad-core header is not used, this patch removes it.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves watchdog-reset header file into mach-s3c64xx.
Because it is not used for others except mach-s3c64xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves onenand-core header file into mach-s3c64xx.
Because it is not used for others except mach-s3c64xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves irq-uart header file into mach-s3c64xx.
Because it is not used for others except mach-s3c64xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves backlight header file into mach-s3c64xx.
Because it is not used for others except mach-s3c64xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves ata-core header file into mach-s3c64xx.
Because it is not used for others except mach-s3c64xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves regs-usb-hsotg-phy header file into mach-s3c64xx.
Because it is not used for others except mach-s3c64xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves spi-core header file into mach-s3c24xx.
Because it is not used for others except mach-s3c24xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves nand-core header file into mach-s3c24xx.
Because it is not used for others except mach-s3c24xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves fb-core header file into mach-s3c24xx.
Because it is not used for others except mach-s3c24xx.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves regs-srom header file into mach-exynos.
Because it is not used for others except mach-exynos.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Pull SCSI target fixes from Nicholas Bellinger:
"This series is larger than what I'd normally be conformable with
sending for a -rc5 PULL request..
However, the bulk of the series is localized to qla2xxx target
specific fixes that address a number of real-world correctness issues,
that have been outstanding on the list for ~6 weeks now. They where
submitted + verified + acked by the HW LLD vendor, contributed by a
major production customer of the code, and are marked for v3.18.y
stable code.
That said, I don't see a good reason to wait another month to get
these fixes into mainline.
Beyond the qla2xx specific fixes, this series also includes:
- bugfix for a long standing use-after-free in iscsi-target during
TPG shutdown + demo-mode sessions.
- bugfix for a >= v4.0 regression OOPs in iscsi-target during a
iscsi_start_kthreads() failure.
- bugfix for a >= v4.0 regression hang in iscsi-target for iser
explicit session/connection logout.
- bugfix for a iser-target bug where a early CMA REJECTED status
during login triggers a NULL pointer dereference OOPs.
- bugfixes for a handful of v4.2-rc1 specific regressions related to
the larger set of recent backend configfs attribute changes.
A big thanks to QLogic + Pure Storage for the qla2xxx target bugfixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
Documentation/target: Fix tcm_mod_builder.py build breakage
iser-target: Fix REJECT CM event use-after-free OOPs
iscsi-target: Fix iser explicit logout TX kthread leak
iscsi-target: Fix iscsit_start_kthreads failure OOPs
iscsi-target: Fix use-after-free during TPG session shutdown
qla2xxx: terminate exchange when command is aborted by LIO
qla2xxx: drop cmds/tmrs arrived while session is being deleted
qla2xxx: disable scsi_transport_fc registration in target mode
qla2xxx: added sess generations to detect RSCN update races
qla2xxx: Abort stale cmds on qla_tgt_wq when plogi arrives
qla2xxx: delay plogi/prli ack until existing sessions are deleted
qla2xxx: cleanup cmd in qla workqueue before processing TMR
qla2xxx: kill sessions/log out initiator on RSCN and port down events
qla2xxx: fix command initialization in target mode.
qla2xxx: Remove msleep in qlt_send_term_exchange
qla2xxx: adjust debug flags
qla2xxx: release request queue reservation.
qla2xxx: Add flush after updating ATIOQ consumer index.
qla2xxx: Enable target mode for ISP27XX
qla2xxx: Fix hardware lock/unlock issue causing kernel panic.
...
This patch moves s5p-dev-mfc from plat-samsung into mach-exynos
because it is used for only exynos no other platforms.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves dev-backlight from plat-samsung into mach-s3c64xx
because it is used for only s3c64xx no other platforms.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch moves setup-camif from plat-samsung into mach-s3c24xx
because it can be used only for s3c24xx no other platforms.
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The semantic associated in tools/perf/ with foo__delete(instance) is to
release all resources referenced by 'instance' members and then release
the memory for 'instance' itself.
The perf_session_env__delete() function isn't doing this, it just does
the first part, but the space used by 'instance' itself isn't freed, as
it is embedded in a larger structure, that will be freed at other stage.
For these cases we se foo__exit(), i.e. the usage is:
void foo__delete(foo)
{
if (foo) {
foo__exit(foo);
free(foo);
}
}
But when we have something like:
struct bar {
struct foo foo;
. . .
}
Then we can't really call foo__delete(&bar.foo), we must have this
instead:
void bar__exit(bar)
{
foo__exit(&bar.foo);
/* free other bar-> resources */
}
void bar__delete(bar)
{
if (bar) {
bar__exit(bar);
free(bar);
}
}
So just rename perf_session_env__delete() to perf_session_env__exit().
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-djbgpcfo5udqptx3q0flwtmk@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When we clear the dirty bits in btrfs_delete_unused_bgs for extents
in the empty block group, it results in btrfs_finish_extent_commit being
unable to discard the freed extents.
The block group removal patch added an alternate path to forget extents
other than btrfs_finish_extent_commit. As a result, any extents that
would be freed when the block group is removed aren't discarded. In my
test run, with a large copy of mixed sized files followed by removal, it
left nearly 2/3 of extents undiscarded.
To clean up the block groups, we add the removed block group onto a list
that will be discarded after transaction commit.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
The cleaner thread may already be sleeping by the time we enter
close_ctree. If that's the case, we'll skip removing any unused
block groups queued for removal, even during a normal umount.
They'll be cleaned up automatically at next mount, but users
expect a umount to be a clean synchronization point, especially
when used on thin-provisioned storage with -odiscard. We also
explicitly remove unused block groups in the ro-remount path
for the same reason.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Since we now clean up block groups automatically as they become
empty, iterating over block groups is no longer sufficient to discard
unused space.
This patch iterates over the unused chunk space and discards any regions
that are unallocated, regardless of whether they were ever used. This is
a change for btrfs but is consistent with other file systems.
We do this in a transactionless manner since the discard process can take
a substantial amount of time and a transaction would need to be started
before the acquisition of the device list lock. That would mean a
transaction would be held open across /all/ of the discards collectively.
In order to prevent other threads from allocating or freeing chunks, we
hold the chunks lock across the search and discard calls. We release it
between searches to allow the file system to perform more-or-less
normally. Since the running transaction can commit and disappear while
we're using the transaction pointer, we take a reference to it and
release it after the search. This is safe since it would happen normally
at the end of the transaction commit after any locks are released anyway.
We also take the commit_root_sem to protect against a transaction starting
and committing while we're running.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Btrfs doesn't track superblocks with extent records so there is nothing
persistent on-disk to indicate that those blocks are in use. We track
the superblocks in memory to ensure they don't get used by removing them
from the free space cache when we load a block group from disk. Prior
to 47ab2a6c6a (Btrfs: remove empty block groups automatically), that
was fine since the block group would never be reclaimed so the superblock
was always safe. Once we started removing the empty block groups, we
were protected by the fact that discards weren't being properly issued
for unused space either via FITRIM or -odiscard. The block groups were
still being released, but the blocks remained on disk.
In order to properly discard unused block groups, we need to filter out
the superblocks from the discard range. Superblocks are located at fixed
locations on each device, so it makes sense to filter them out in
btrfs_issue_discard, which is used by both -odiscard and FITRIM.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
It's possible, though unexpected, to pass unaligned offsets and lengths
to btrfs_issue_discard. We then shift the offset/length values to sector
units. If an unaligned offset has been passed, it will result in the
entire sector being discarded, possibly losing data. An unaligned
length is safe but we'll end up returning an inaccurate number of
discarded bytes.
This patch aligns the offset to the 512B boundary, adjusts the length,
and warns, since we shouldn't be discarding on an offset that isn't
aligned with our sector size.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Initially this will just be the length argument passed to it,
but the following patches will adjust that to reflect re-alignment
and skipped blocks.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Tested-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
These changes allow a PHY driver to trigger a VBUS interrupt and
to provide the value of VBUS.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
ether unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
composite unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate usb otg descriptor and initialize it according to gadget's otg
capabilities, if usb_otg_caps is not set, keep settings as current gadget
drivers. With this 2 new interfaces, gadget can use usb_otg_descriptor
for OTG 1.x, and usb_otg20_descriptor for OTG 2.0 or above, and otg
features can be decided by the combination of usb hardware property
and driver config.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After introduce usb otg properties, update ci_otg_is_fsm_mode conditions
to be depending on both usb hardware properties and usb driver config,
also resolve a compile issue in debug.c after the API change.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Init and update otg capabilities by DT, set gadget's otg capabilities
accordingly.
Acked-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Check property of usb hardware to update otg version and disable SRP, HNP
and ADP if its disable flag is present.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add otg version, srp, hnp and adp support for usb OTG port, then those OTG
features don't have to be decided by usb gadget drivers.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Copy usb_otg_descriptor from config's descriptor if host requests
USB_DT_OTG.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add usb_otg_caps pointer to usb_gadget structure to indicate its
otg capabilities.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds a structure usb_otg_caps to cover all otg related
capabilities of the device, including otg revision, and if hnp/srp/adp
is supported.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add USB_OTG_ADP definition for usb_otg_descriptor.bmAttributes.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
OTG 2.0 introduces bcdOTG in otg descriptor to identify the OTG and EH
supplement release number with which the OTG device is compliant, this
patch adds structure usb_otg20_descriptor for OTG 2.0 and above.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
