The UniPhier on-chip UART driver was merged into the mainline by
commit 1a8d2903cb ("serial: 8250_uniphier: add UniPhier serial
driver").
Add device nodes to make it really available.
We no longer have to depend on the on-board UART device (16550A),
so let's change the chosen and aliases to point to the on-chip ones.
Also, turn on the on-board Ethernet device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The 'digicolor' regexp doesn't cover the dts files. Add a glob pattern for
them.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
Ux500 is regressing due to commit
a21763a0b1
"pinctrl: nomadik: activate strict mux mode" which disallows
Nomadik GPIO 5 to be muxed in as a level shifter voltage select
pin, as it is currently described as being used for RX on UART1.
The behaviour is correct, instead the hardware config has been
incorrecly specified: UART1 is indeed unused on HREFv60plus and
Snowball and that is why HREFv60plus can use the pins it would
normally occupy as the voltage select line for the MMC/SD
levelshifter (Snowball uses it for I2C4).
The reason UART1 was anyway enabled on these platforms was
probably to secure the port enumeration to userspace. This
can be solved by using aliases (done in a separate patch) so
we can now deactivate UART1 and let MMC/SD use it properly
on HREFv60plus. We explicitly activate it only for the
older HREFprev60 board.
To complete, we set up the pin configuration for these pins
properly in the sdi0 node.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The control_data field of the snd_soc_codec struct is no longer used by
ASoC drivers using standard regmap IO.
There is no need to initialize the field to point to the drivers regmap
struct, so drop that.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mixer control for widgets can't be created if the info is NULL. So assign
the correct info for this.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Previously only core DRM ioctls under the DRM_COMMAND_BASE were being
forwarded, but the drm.h header suggests (and reality confirms) ones
after (and including) DRM_COMMAND_END should be forwarded as well.
We need this to correctly forward the compat ioctl for the botched-up
addfb2.1 extension.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: stable@vger.kernel.org # 4.1+
[danvet: Explain why this is suddenly needed and add cc: stable.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix crash in 3.5+ if FTP is used after switching
sync_version to 0.
Fixes: 749c42b620 ("ipvs: reduce sync rate with time thresholds")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
It is possible that we bind against a local socket in early_demux when we
are actually going to want to forward it. In this case, the socket serves
no purpose and only serves to confuse things (particularly functions which
implicitly expect sk_fullsock to be true, like ip_local_out).
Additionally, skb_set_owner_w is totally broken for non full-socks.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Fixes: 41063e9dd1 ("ipv4: Early TCP socket demux.")
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
I overlooked the svc->sched_data usage from schedulers
when the services were converted to RCU in 3.10. Now
the rare ipvsadm -E command can change the scheduler
but due to the reverse order of ip_vs_bind_scheduler
and ip_vs_unbind_scheduler we provide new sched_data
to the old scheduler resulting in a crash.
To fix it without changing the scheduler methods we
have to use synchronize_rcu() only for the editing case.
It means all svc->scheduler readers should expect a
NULL value. To avoid breakage for the service listing
and ipvsadm -R we can use the "none" name to indicate
that scheduler is not assigned, a state when we drop
new connections.
Reported-by: Alexander Vasiliev <a.vasylev@404-group.com>
Fixes: ceec4c3816 ("ipvs: convert services to rcu")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Michael Vallaly reports about wrong source address used
in rare cases for tunneled traffic. Looks like
__ip_vs_get_out_rt in 3.10+ is providing uninitialized
dest_dst->dst_saddr.ip because ip_vs_dest_dst_alloc uses
kmalloc. While we retry after seeing EINVAL from routing
for data that does not look like valid local address, it
still succeeded when this memory was previously used from
other dests and with different local addresses. As result,
we can use valid local address that is not suitable for
our real server.
Fix it by providing 0.0.0.0 every time our cache is refreshed.
By this way we will get preferred source address from routing.
Reported-by: Michael Vallaly <lvs@nolatency.com>
Fixes: 026ace060d ("ipvs: optimize dst usage for real server")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Previously there was a trivial panic
unshare -n /bin/bash <<EOF
ip addr add dev lo face::1/128
ipvsadm -A -t [face::1]:15213
ipvsadm -a -t [face::1]:15213 -r b00c::1
echo boom | nc face::1 15213
EOF
This patch allows us to replicate the net logic above and simply capture
the skb_dst(skb)->dev and use that for the purpose of the invocation.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
With shmobile_defconfig but SMP=n && SUSPEND=n, I get:
arch/arm/mach-shmobile/platsmp-apmu.c:49:12: warning: 'apmu_power_off' defined but not used [-Wunused-function]
arch/arm/mach-shmobile/platsmp-apmu.c:70:12: warning: 'apmu_wrap' defined but not used [-Wunused-function]
Annotate those functions like the functions around it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
build in snvs powerkey
build in syscon power off support
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable low-level debug support for i.MX6UL by adding the
debug port definitions for the SoC.
Singed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP5 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP4 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The device tree for Gumstix Pepper has DCDC2 and
DCDC3 correctly labelled but the upper limit values
are wrong. The confusion is due to the hardware
quirk where the DCDC2 and DCDC3 wires are flipped
in Pepper.
Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
Tested-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boot process is halting in midway because some of the necessary voltage
regulators are deemed unused and subsequently powered off, leading to
a completely unresponsive system.
Most of the device nodes had correct voltage regulator attachments.
Yet these nodes had to set stricter enforcement on them through
'regulator-boot-on' and 'regulator-always-on' to function correctly.
The consumers of the regulators this commit affect are the followings:
DCDC1: vdd_1v8 system supply, USB-PHY, and ADC
DCDC2: Core domain
DCDC3: MPU core domain
LDO1: RTC
LDO2: 3v3 IO domain
LDO3: USB-PHY; not a boot-time requirement
LDO4: LCD [16:23]
All but LDO3 need to be always-on for the system to be functional.
Additionally regulator-name properties have been added for the kernel to
display the name from the schematic. This will improve diagnostics.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For Gumstix Overo COMs, the u-boot bootloader typically passes an
argument specifying the default display via the omapdss.def_disp
parameter. When a default display is specified, DSS2 tries to match
this name with either the device tree label (e.g. label=dvi) or,
failing this, the device tree alias (e.g. label=display0). Update the
panel names for the 'lcd43' and 'lcd35' displays in the device tree
such that they match the names passed by u-boot.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
vmx-crypto driver make use of some VSX instructions which are
only available if VSX is enabled. Running in cases where VSX
are not enabled vmx-crypto fails in a VSX exception.
In order to fix this enable_kernel_vsx() was added to turn on
VSX instructions for vmx-crypto.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
enable_kernel_vsx() function was commented since anything was using
it. However, vmx-crypto driver uses VSX instructions which are
only available if VSX is enable. Otherwise it rises an exception oops.
This patch uncomment enable_kernel_vsx() routine and makes it available.
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts rfc4106 to the new calling convention where
the IV is now part of the AD and needs to be skipped.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts rfc4106 to the new calling convention where
the IV is now part of the AD and needs to be skipped. This patch
also makes use of type-safe AEAD functions where possible.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts rfc4106 to the new calling convention where
the IV is now part of the AD and needs to be skipped. This patch
also makes use of the new type-safe way of freeing instances.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts rfc4106 to the new calling convention where
the IV is now in the AD and needs to be skipped.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch allows the AEAD speed tests to cope with the new seqiv
calling convention as well as the old one.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch disables the rfc4106 test while the conversion to the
new seqiv calling convention takes place. It also converts the
rfc4106 test vectors to the new format.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch replaces the seqniv generator with seqiv when the
underlying algorithm understands the new calling convention.
This not only makes more sense as now seqiv is solely responsible
for IV generation rather than also determining how the IV is going
to be used, it also allows for optimisations in the underlying
implementation. For example, the space for the IV could be used
to add padding for authentication.
This patch also removes the unnecessary copying of IV to dst
during seqiv decryption as the IV is part of the AD and not cipher
text.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a bug where we were incorrectly including the
IV in the AD during encryption. The IV must remain in the plain
text for it to be encrypted.
During decryption there is no need to copy the IV to dst because
it's now part of the AD.
This patch removes an unncessary check on authsize which would be
performed by the underlying decrypt call.
Finally this patch makes use of the type-safe init/exit functions.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch allows the CRYPTO_ALG_AEAD_NEW flag to be propagated.
It also restores the ASYNC bit that went missing during the AEAD
conversion.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a type-safe function for freeing AEAD instances
to struct aead_instance. This replaces the existing free function
in struct crypto_template which does not know the type of the
instance that it's freeing.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently the task of freeing an instance is given to the crypto
template. However, it has no type information on the instance so
we have to resort to checking type information at runtime.
This patch introduces a free function to crypto_type that will be
used to free an instance. This can then be used to free an instance
in a type-safe manner.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The transform context is shared memory and must not be written
to without locking. This patch adds locking to nx-842 to prevent
context corruption.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
