Florian Fainelli says:
====================
net: dsa: OF parsing fixes
This patch series fixes two small parsing issues, the first one was
reported by Dan, the second came after looking more closely at the
code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cd->sw_addr is used as a MDIO bus address, which cannot exceed
PHY_MAX_ADDR (32), our check was off-by-one.
Fixes: 5e95329b70 ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
port_index is used an index into an array, and this information comes
from Device Tree, make sure that port_index is not equal to the array
size before using it. Move the check against port_index earlier in the
loop.
Fixes: 5e95329b70: ("dsa: add device tree bindings to register DSA switches")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to abort attribute setting or object addition, if the
prepare phase returned operation not supported.
Thus, abort these two transactions only if the error is not -EOPNOTSUPP.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3cc4949269.
There is nothing wrong with coalescing during defragmentation, it
reduces truesize overhead and simplifies things for the receiving
socket (no fraglist walk needed).
However, it also destroys geometry of the original fragments.
While that doesn't cause any breakage (we make sure to not exceed largest
original size) ip_do_fragment contains a 'fastpath' that takes advantage
of a present frag list and results in fragments that (in most cases)
match what was received.
In case its needed the coalescing could be done later, when we're sure
the skb is not forwarded. But discussion during NFWS resulted in
'lets just remove this for now'.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet driver needs to separate packet drops from packet errors.
When the driver has to drop a *good* packet, due to lack of buffers or
replacement skbs, increment only dev->stats.[rx|tx]_dropped.
When the driver encounters a bad Rx packet or Tx error, increment only
dev->stats.[rx|tx]_errors + relevant detailed error counter.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update referenced specs link to reflect actual file version and location.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull libnvdimm fixes from Dan Williams:
"1) Fixes for a handful of smatch reports (Thanks Dan C.!) and minor
bug fixes (patches 1-6)
2) Correctness fixes to the BLK-mode nvdimm driver (patches 7-10).
Granted these are slightly large for a -rc update. They have been
out for review in one form or another since the end of May and were
deferred from the merge window while we settled on the "PMEM API"
for the PMEM-mode nvdimm driver (ie memremap_pmem, memcpy_to_pmem,
and wmb_pmem).
Now that those apis are merged we implement them in the BLK driver
to guarantee that mmio aperture moves stay ordered with respect to
incoming read/write requests, and that writes are flushed through
those mmio-windows and platform-buffers to be persistent on media.
These pass the sub-system unit tests with the updates to
tools/testing/nvdimm, and have received a successful build-report from
the kbuild robot (468 configs).
With acks from Rafael for the touches to drivers/acpi/"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm:
nfit: add support for NVDIMM "latch" flag
nfit: update block I/O path to use PMEM API
tools/testing/nvdimm: add mock acpi_nfit_flush_address entries to nfit_test
tools/testing/nvdimm: fix return code for unimplemented commands
tools/testing/nvdimm: mock ioremap_wt
pmem: add maintainer for include/linux/pmem.h
nfit: fix smatch "use after null check" report
nvdimm: Fix return value of nvdimm_bus_init() if class_create() fails
libnvdimm: smatch cleanups in __nd_ioctl
sparse: fix misplaced __pmem definition
With commit 02b4e2756e ("ARM: v7 setup
function should invalidate L1 cache"), the default secondary_startup
function for ARMv7 CPUs does invalidate the L1 cache, which was the sole
reason why BCM63xx had to have its own secondary_startup implementation.
Now that the secondary_startup takes care of this, we can completely
remove that code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
of_get_cpu_node provides the device node associated with the given
logical CPU and cpu_logical_map contains the physical id for each CPU
in the logical ordering. Passing cpu_logical_map(cpu) to of_get_cpu_node
is incorrect.
This patch fixes the issue by passing the logical CPU number to
of_get_cpu_node
Fixes: ed5cd8163d ("ARM: BCM63xx: Add SMP support for BCM63138")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Let's switch to using standard touchscreen device properties parsing module
instead of doing it by hand in the driver.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will perform necessary settings for performing
multi-touch to single-touch emulation, we do not need to do that ourselves.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller has a RESET pin which is usually controlled over
a GPIO line. If such a GPIO is provided, perform a RESET
during probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using threaded interrupt handler and thus are allowed to sleep.
Let's switch over to gpiod_get_value_cansleep() so that we do not get
ugly warnings in case GPIO controller might sleep when accessing GPIO.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows uniform parsing on legacy, DT and ACPI systems.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's move driver's platform data definitions from include/linux/input/
into include/linux/platform_data/ so that it stays with the rest of
platform data definitions.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch form OF to device properties so that common parsing code could
work not only on device tree but also on ACPI-based platforms.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The binding specification says that "touchscreen-size-x" and "-y" specify
horizontal and vertical resolution of the touchscreen and therefore maximum
absolute coordinates should be reduced by 1 since we are starting with 0.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do issue warning about axis that is present in device tree but not specified
by the driver even in case of multi-touch axis as callers now tell us if they
expect multi-touch data or not.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When we have an extent that got N references removed and N new references
added in the same transaction, we must run the insertion of the references
first because otherwise the last removed reference will remove the extent
item from the extent tree, resulting in a failure for the insertions.
This is a regression introduced in the 4.2-rc1 release and this fix just
brings back the behaviour of selecting reference additions before any
reference removals.
The following test case for fstests reproduces the issue:
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
tmp=/tmp/$$
status=1 # failure is the default!
trap "_cleanup; exit \$status" 0 1 2 3 15
_cleanup()
{
_cleanup_flakey
rm -f $tmp.*
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
. ./common/dmflakey
# real QA test starts here
_need_to_be_root
_supported_fs btrfs
_supported_os Linux
_require_scratch
_require_dm_flakey
_require_cloner
_require_metadata_journaling $SCRATCH_DEV
rm -f $seqres.full
_scratch_mkfs >>$seqres.full 2>&1
_init_flakey
_mount_flakey
# Create prealloc extent covering range [160K, 620K[
$XFS_IO_PROG -f -c "falloc 160K 460K" $SCRATCH_MNT/foo
# Now write to the last 80K of the prealloc extent plus 40K to the unallocated
# space that immediately follows it. This creates a new extent of 40K that spans
# the range [620K, 660K[.
$XFS_IO_PROG -c "pwrite -S 0xaa 540K 120K" $SCRATCH_MNT/foo | _filter_xfs_io
# At this point, there are now 2 back references to the prealloc extent in our
# extent tree. Both are for our file offset 160K and one relates to a file
# extent item with a data offset of 0 and a length of 380K, while the other
# relates to a file extent item with a data offset of 380K and a length of 80K.
# Make sure everything done so far is durably persisted (all back references are
# in the extent tree, etc).
sync
# Now clone all extents of our file that cover the offset 160K up to its eof
# (660K at this point) into itself at offset 2M. This leaves a hole in the file
# covering the range [660K, 2M[. The prealloc extent will now be referenced by
# the file twice, once for offset 160K and once for offset 2M. The 40K extent
# that follows the prealloc extent will also be referenced twice by our file,
# once for offset 620K and once for offset 2M + 460K.
$CLONER_PROG -s $((160 * 1024)) -d $((2 * 1024 * 1024)) -l 0 $SCRATCH_MNT/foo \
$SCRATCH_MNT/foo
# Now create one new extent in our file with a size of 100Kb. It will span the
# range [3M, 3M + 100K[. It also will cause creation of a hole spanning the
# range [2M + 460K, 3M[. Our new file size is 3M + 100K.
$XFS_IO_PROG -c "pwrite -S 0xbb 3M 100K" $SCRATCH_MNT/foo | _filter_xfs_io
# At this point, there are now (in memory) 4 back references to the prealloc
# extent.
#
# Two of them are for file offset 160K, related to file extent items
# matching the file offsets 160K and 540K respectively, with data offsets of
# 0 and 380K respectively, and with lengths of 380K and 80K respectively.
#
# The other two references are for file offset 2M, related to file extent items
# matching the file offsets 2M and 2M + 380K respectively, with data offsets of
# 0 and 380K respectively, and with lengths of 389K and 80K respectively.
#
# The 40K extent has 2 back references, one for file offset 620K and the other
# for file offset 2M + 460K.
#
# The 100K extent has a single back reference and it relates to file offset 3M.
# Now clone our 100K extent into offset 600K. That offset covers the last 20K
# of the prealloc extent, the whole 40K extent and 40K of the hole starting at
# offset 660K.
$CLONER_PROG -s $((3 * 1024 * 1024)) -d $((600 * 1024)) -l $((100 * 1024)) \
$SCRATCH_MNT/foo $SCRATCH_MNT/foo
# At this point there's only one reference to the 40K extent, at file offset
# 2M + 460K, we have 4 references for the prealloc extent (2 for file offset
# 160K and 2 for file offset 2M) and 2 references for the 100K extent (1 for
# file offset 3M and a new one for file offset 600K).
# Now fsync our file to make all its new data and metadata updates are durably
# persisted and present if a power failure/crash happens after a successful
# fsync and before the next transaction commit.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
echo "File digest before power failure:"
md5sum $SCRATCH_MNT/foo | _filter_scratch
# Silently drop all writes and ummount to simulate a crash/power failure.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
# Allow writes again, mount to trigger log replay and validate file contents.
# During log replay, the btrfs delayed references implementation used to run the
# deletion of back references before the addition of new back references, which
# made the addition fail as it didn't find the key in the extent tree that it
# was looking for. The failure triggered by this test was related to the 40K
# extent, which got 1 reference dropped and 1 reference added during the fsync
# log replay - when running the delayed references at transaction commit time,
# btrfs was applying the deletion before the insertion, resulting in a failure
# of the insertion that ended up turning the fs into read-only mode.
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
echo "File digest after log replay:"
md5sum $SCRATCH_MNT/foo | _filter_scratch
_unmount_flakey
status=0
exit
This issue turned the filesystem into read-only mode (current transaction
aborted) and produced the following traces:
[ 8247.578385] ------------[ cut here ]------------
[ 8247.579947] WARNING: CPU: 0 PID: 11341 at fs/btrfs/extent-tree.c:1547 lookup_inline_extent_backref+0x17d/0x45d [btrfs]()
(...)
[ 8247.601697] Call Trace:
[ 8247.602222] [<ffffffff8145f077>] dump_stack+0x4f/0x7b
[ 8247.604320] [<ffffffff8104b3b0>] warn_slowpath_common+0xa1/0xbb
[ 8247.605488] [<ffffffffa0506c8d>] ? lookup_inline_extent_backref+0x17d/0x45d [btrfs]
[ 8247.608226] [<ffffffffa0506c8d>] lookup_inline_extent_backref+0x17d/0x45d [btrfs]
[ 8247.617061] [<ffffffffa0507957>] insert_inline_extent_backref+0x41/0xb2 [btrfs]
[ 8247.621856] [<ffffffffa0507c4f>] __btrfs_inc_extent_ref+0x8c/0x20a [btrfs]
[ 8247.624366] [<ffffffffa050ee60>] __btrfs_run_delayed_refs+0xb0c/0xd49 [btrfs]
[ 8247.626176] [<ffffffffa0510dcd>] btrfs_run_delayed_refs+0x6d/0x1d4 [btrfs]
[ 8247.627435] [<ffffffff81155c9b>] ? __cache_free+0x4a7/0x4b6
[ 8247.628531] [<ffffffffa0520482>] btrfs_commit_transaction+0x4c/0xa20 [btrfs]
(...)
[ 8247.648430] ---[ end trace 2461e55f92c2ac2d ]---
[ 8247.727263] WARNING: CPU: 3 PID: 11341 at fs/btrfs/extent-tree.c:2771 btrfs_run_delayed_refs+0xa4/0x1d4 [btrfs]()
[ 8247.728954] BTRFS: Transaction aborted (error -5)
(...)
[ 8247.760866] Call Trace:
[ 8247.761534] [<ffffffff8145f077>] dump_stack+0x4f/0x7b
[ 8247.764271] [<ffffffff8104b3b0>] warn_slowpath_common+0xa1/0xbb
[ 8247.767582] [<ffffffffa0510e04>] ? btrfs_run_delayed_refs+0xa4/0x1d4 [btrfs]
[ 8247.769373] [<ffffffff8104b410>] warn_slowpath_fmt+0x46/0x48
[ 8247.770836] [<ffffffffa0510e04>] btrfs_run_delayed_refs+0xa4/0x1d4 [btrfs]
[ 8247.772532] [<ffffffff81155c9b>] ? __cache_free+0x4a7/0x4b6
[ 8247.773664] [<ffffffffa0520482>] btrfs_commit_transaction+0x4c/0xa20 [btrfs]
[ 8247.775047] [<ffffffff81087310>] ? trace_hardirqs_on+0xd/0xf
[ 8247.776176] [<ffffffff81155dd5>] ? kmem_cache_free+0x12b/0x189
[ 8247.777427] [<ffffffffa055a920>] btrfs_recover_log_trees+0x2da/0x33d [btrfs]
[ 8247.778575] [<ffffffffa055898e>] ? replay_one_extent+0x4fc/0x4fc [btrfs]
[ 8247.779838] [<ffffffffa051e265>] open_ctree+0x1cc0/0x201a [btrfs]
[ 8247.781020] [<ffffffff81120f48>] ? register_shrinker+0x56/0x81
[ 8247.782285] [<ffffffffa04fb12c>] btrfs_mount+0x5f0/0x734 [btrfs]
(...)
[ 8247.793394] ---[ end trace 2461e55f92c2ac2e ]---
[ 8247.794276] BTRFS: error (device dm-0) in btrfs_run_delayed_refs:2771: errno=-5 IO failure
[ 8247.797335] BTRFS: error (device dm-0) in btrfs_replay_log:2375: errno=-5 IO failure (Failed to recover log tree)
Fixes: c6fc245499 ("btrfs: delayed-ref: Use list to replace the ref_root in ref_head.")
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Acked-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
When we call btrfs_commit_transaction(), we splice the list "ordered"
of our transaction handle into the transaction's "pending_ordered"
list, but we don't re-initialize the "ordered" list of our transaction
handle, this means it still points to the same elements it used to
before the splice. Then we check if the current transaction's state is
>= TRANS_STATE_COMMIT_START and if it is we end up calling
btrfs_end_transaction() which simply splices again the "ordered" list
of our handle into the transaction's "pending_ordered" list, leaving
multiple pointers to the same ordered extents which results in list
corruption when we are iterating, removing and freeing ordered extents
at btrfs_wait_pending_ordered(), resulting in access to dangling
pointers / use-after-free issues.
Similarly, btrfs_end_transaction() can end up in some cases calling
btrfs_commit_transaction(), and both did a list splice of the transaction
handle's "ordered" list into the transaction's "pending_ordered" without
re-initializing the handle's "ordered" list, resulting in exactly the
same problem.
This produces the following warning on a kernel with linked list
debugging enabled:
[109749.265416] ------------[ cut here ]------------
[109749.266410] WARNING: CPU: 7 PID: 324 at lib/list_debug.c:59 __list_del_entry+0x5a/0x98()
[109749.267969] list_del corruption. prev->next should be ffff8800ba087e20, but was fffffff8c1f7c35d
(...)
[109749.287505] Call Trace:
[109749.288135] [<ffffffff8145f077>] dump_stack+0x4f/0x7b
[109749.298080] [<ffffffff81095de5>] ? console_unlock+0x356/0x3a2
[109749.331605] [<ffffffff8104b3b0>] warn_slowpath_common+0xa1/0xbb
[109749.334849] [<ffffffff81260642>] ? __list_del_entry+0x5a/0x98
[109749.337093] [<ffffffff8104b410>] warn_slowpath_fmt+0x46/0x48
[109749.337847] [<ffffffff81260642>] __list_del_entry+0x5a/0x98
[109749.338678] [<ffffffffa053e8bf>] btrfs_wait_pending_ordered+0x46/0xdb [btrfs]
[109749.340145] [<ffffffffa058a65f>] ? __btrfs_run_delayed_items+0x149/0x163 [btrfs]
[109749.348313] [<ffffffffa054077d>] btrfs_commit_transaction+0x36b/0xa10 [btrfs]
[109749.349745] [<ffffffff81087310>] ? trace_hardirqs_on+0xd/0xf
[109749.350819] [<ffffffffa055370d>] btrfs_sync_file+0x36f/0x3fc [btrfs]
[109749.351976] [<ffffffff8118ec98>] vfs_fsync_range+0x8f/0x9e
[109749.360341] [<ffffffff8118ecc3>] vfs_fsync+0x1c/0x1e
[109749.368828] [<ffffffff8118ee1d>] do_fsync+0x34/0x4e
[109749.369790] [<ffffffff8118f045>] SyS_fsync+0x10/0x14
[109749.370925] [<ffffffff81465197>] system_call_fastpath+0x12/0x6f
[109749.382274] ---[ end trace 48e0d07f7c03d95a ]---
On a non-debug kernel this leads to invalid memory accesses, causing a
crash. Fix this by using list_splice_init() instead of list_splice() in
btrfs_commit_transaction() and btrfs_end_transaction().
Cc: stable@vger.kernel.org
Fixes: 50d9aa99bd ("Btrfs: make sure logged extents complete in the current transaction V3"
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
We were allocating memory with memdup_user() but we were never releasing
that memory. This affected pretty much every call to the ioctl, whether
it deduplicated extents or not.
This issue was reported on IRC by Julian Taylor and on the mailing list
by Marcel Ritter, credit goes to them for finding the issue.
Reported-by: Julian Taylor <jtaylor.debian@googlemail.com>
Reported-by: Marcel Ritter <ritter.marcel@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
If the no_holes feature is enabled, we attempt to shrink a file to a size
that ends up in the middle of a hole and we don't have any file extent
items in the fs/subvol tree that go beyond the new file size (or any
ordered extents that will insert such file extent items), we end up not
updating the inode's disk_i_size, we only update the inode's i_size.
This means that after unmounting and mounting the filesystem, or after
the inode is evicted and reloaded, its i_size ends up being incorrect
(an inode's i_size is set to the disk_i_size field when an inode is
loaded). This happens when btrfs_truncate_inode_items() doesn't find
any file extent items to drop - in this case it never makes a call to
btrfs_ordered_update_i_size() in order to update the inode's disk_i_size.
Example reproducer:
$ mkfs.btrfs -O no-holes -f /dev/sdd
$ mount /dev/sdd /mnt
# Create our test file with some data and durably persist it.
$ xfs_io -f -c "pwrite -S 0xaa 0 128K" /mnt/foo
$ sync
# Append some data to the file, increasing its size, and leave a hole
# between the old size and the start offset if the following write. So
# our file gets a hole in the range [128Kb, 256Kb[.
$ xfs_io -c "truncate 160K" /mnt/foo
# We expect to see our file with a size of 160Kb, with the first 128Kb
# of data all having the value 0xaa and the remaining 32Kb of data all
# having the value 0x00.
$ od -t x1 /mnt/foo
0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
*
0400000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
*
0500000
# Now cleanly unmount and mount again the filesystem.
$ umount /mnt
$ mount /dev/sdd /mnt
# We expect to get the same result as before, a file with a size of
# 160Kb, with the first 128Kb of data all having the value 0xaa and the
# remaining 32Kb of data all having the value 0x00.
$ od -t x1 /mnt/foo
0000000 aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa aa
*
0400000
In the example above the file size/data do not match what they were before
the remount.
Fix this by always calling btrfs_ordered_update_i_size() with a size
matching the size the file was truncated to if btrfs_truncate_inode_items()
is not called for a log tree and no file extent items were dropped. This
ensures the same behaviour as when the no_holes feature is not enabled.
A test case for fstests follows soon.
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/1433391238-19471-11-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use access helper irq_data_get_affinity_mask() to hide implementation
details of struct irq_desc.
[ tglx: Verified with coccinelle ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1433145945-789-30-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: linux-arm-kernel@lists.infradead.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-metag@vger.kernel.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
|
-irq_set_handler_data(E1, E2);
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_handler_data(E1, E2) != 0)
- BUG();
...
|
-irq_set_handler_data(E1, E2);
...
)
-irq_set_chained_handler(E1, E3);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Unused except for the alpha wrapper, which can retrieve if from the
irq descriptor.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1433391238-19471-21-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provide a irq_desc based variant of irq_can_set_affinity() to avoid a
redundant lookup for the core code users.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Only required for the slow path. Retrieve it from irq descriptor if
necessary.
[ tglx: Split out from combo patch. Left [try_]misrouted_irq()
untouched as there is no win in the slow path ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/1433391238-19471-19-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unused argument.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Not really a hotpath, so __report_bad_irq() can retrieve the irq
number from the irq descriptor.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unused argument in both functions.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Solely used for debug output. Can be retrieved from irq descriptor if
necessary.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It's only required for debug output and can be retrieved from the irq
descriptor if necessary.
[ tglx: Split out from combo patch ]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It's only used in the software resend case and can be retrieved from
irq_desc if necessary.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1433391238-19471-18-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The first parameter 'irq' is never used by
kstat_incr_irqs_this_cpu(). Remove it.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/1433391238-19471-16-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_alloc_domain_generic_chips() can only be called once for an
irqdomain. The sirfsoc init calls it twice and because the return
value is not checked it does not notice the wreckage.
The code works by chance because the first call already allocates two
chips and therefor the second call to sirfsoc_alloc_gc() operates on
the proper generic chip instance.
Use a single call and setup the two chips in the obvious correct way.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Olof Johansson <olof@lixom.net>
Link: http://lkml.kernel.org/r/20150706101543.470696950@linutronix.de
The num_ct argument of irq_alloc_domain_generic_chips() tells the core
code how many chip types (for different control flows,
e.g. edge/level) should be allocated. It does not control how many
generic chip instances are created because that's determined from the
irq domain size and the number of interrupts per chip.
The dw-apb init abuses the num_ct argument for allocating one or two
chip types depending on the number of interrupts. That's completely
wrong because the alternate type is never used.
This code was obviously never tested on a system which has more than
32 interrupts as that would have never worked due to the unitialized
second generic chip instance.
Hand in the proper num_ct=1 and fixup the chip initialization along
with the interrupt handler.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/20150706101543.373582262@linutronix.de
