Broken in "[PATCH] ufs: truncate should allocate block for last byte";
all way back in 2006. ufs_setattr() hadn't been the only user of
vmtruncate() and eliminating ->truncate() method required corrections
in a bunch of places. Eventually those places had migrated into
->write_begin() failure exit and ->write_end() after short copy...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
a) move it inside ufs_truncate()
b) ufs_free_inode() doesn't need it - it's serialized on ->s_lock
c) ufs_write_inode() doesn't need it either (and can be called without
it anyway).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Its not a good idea to keep target specific definition of
the same t10-pi tuple.
(Fix v4.2-rc1 patch fuzz - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We should use "HiFi Playback" and "HiFi Capture".it will fix below err
cht-bsw-max98090: ASoC: no sink widget found for AIF1 Playback
cht-bsw-max98090: ASoC: Failed to add route ssp2 Tx -> direct ->
AIF1 Playback
cht-bsw-max98090: ASoC: no source widget found for AIF1 Capture
cht-bsw-max98090: ASoC: Failed to add route AIF1 Capture -> direct ->
ssp2 Rx
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add lockdep_assert_held_once() to functions explicitly mentioning that
rdev or regulator_list mutex must be held. Using WARN_ONCE shouldn't
pollute the dmesg to much.
The patch (if CONFIG_LOCKDEP enabled) will show warnings in certain
regulators calling regulator_notifier_call_chain() without rdev->mutex
held.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RCU_USER_QS Kconfig parameter is now just a synonym for NO_HZ_FULL,
so this commit eliminates RCU_USER_QS, replacing all uses with NO_HZ_FULL.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Add myself as maintainer of the NAND based MSystems DiskOnChip G3
driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
dmi_check_system() takes "const struct dmi_system_id *", so make the
dmi_system_id table const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it obvious that unexpected value read from ID register is printed in
hexadecimal.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it obvious that unexpected value read from ID register is printed in
hexadecimal.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it obvious that unexpected value read from ID register is printed in
hexadecimal.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it obvious that unexpected value read from ID register is printed in
hexadecimal.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it obvious that unexpected value read from ID register is printed in
hexadecimal.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it obvious that unexpected value read from ID register is printed in
hexadecimal.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MODULE_ALIAS needs to match the driver name to make module auto-loading
work. Also move MODULE_ALIAS close to other MODULE_* macro.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sound/soc/codecs/gtm601.c:86:4-9: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Marek Belisko <marek@goldelico.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add option to vendor-prefixes file which will be used for Option NV company.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver add PCM interface to a GTM601 UMTS modem chip.
There is no configuration interface.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Follow the correct pipe vs port disable sequence for the PCH LVDS
ports, ie. disable the port after the pipe.
Other PCH port were already converted in the following commits:
1ea56e269e drm/i915: Disable CRT port after pipe on PCH platforms
3c65d1d1bb drm/i915: Disable SDVO port after the pipe on PCH platforms
a4790cec3a drm/i915: Disable HDMI port after the pipe on PCH platforms
08aff3fe26 drm/i915: Move DP port disable to post_disable for pch platforms
but LVDS was forgotten.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DAPM lock must be held when accessing the DAPM graph status through
sysfs or debugfs, otherwise concurrent changes to the graph can result in
undefined behaviour.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch fixes the mux bit-setting for ClockgenA9.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Fixes: 13e6f2da1d ("clk: st: STiH407: Support for A9 MUX Clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the CLK_GET_RATE_NOCACHE flag to all the clocks with recalc ops,
so that they reflect Hw rate after CPS wake-up when a clk_get_rate()
is called
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
While proving lock, the following warning happens
and it is fixed after initializing lock in the setup
function
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.27-02861-g39df285-dirty #33
[<c00154ac>] (unwind_backtrace+0x0/0xf4) from [<c0011b50>] (show_stack+0x10/0x14)
[<c0011b50>] (show_stack+0x10/0x14) from [<c00689ac>] (__lock_acquire+0x900/0xb14)
[<c00689ac>] (__lock_acquire+0x900/0xb14) from [<c0069394>] (lock_acquire+0x68/0x7c)
[<c0069394>] (lock_acquire+0x68/0x7c) from [<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c)
[<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c) from [<c0381e6c>] (clk_gate_endisable+0x28/0x88)
[<c0381e6c>] (clk_gate_endisable+0x28/0x88) from [<c0381ee0>] (clk_gate_enable+0xc/0x14)
[<c0381ee0>] (clk_gate_enable+0xc/0x14) from [<c0386c68>] (flexgen_enable+0x28/0x40)
[<c0386c68>] (flexgen_enable+0x28/0x40) from [<c037f260>] (__clk_enable+0x5c/0x9c)
[<c037f260>] (__clk_enable+0x5c/0x9c) from [<c037f558>] (clk_enable+0x18/0x2c)
[<c037f558>] (clk_enable+0x18/0x2c) from [<c064a1dc>] (st_lpc_of_register+0xc0/0x248)
[<c064a1dc>] (st_lpc_of_register+0xc0/0x248) from [<c0649e44>] (clocksource_of_init+0x34/0x58)
[<c0649e44>] (clocksource_of_init+0x34/0x58) from [<c0637ddc>] (sti_timer_init+0x10/0x18)
[<c0637ddc>] (sti_timer_init+0x10/0x18) from [<c06343f8>] (time_init+0x20/0x30)
[<c06343f8>] (time_init+0x20/0x30) from [<c0632984>] (start_kernel+0x20c/0x2e8)
[<c0632984>] (start_kernel+0x20c/0x2e8) from [<40008074>] (0x40008074)
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Fixes: b116517055 ("clk: st: STiH407: Support for Flexgen Clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch fixes the value for disabling the FSYN channel clock.
The 'is_enabled' returned value is also fixed.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Remove this duplicated code due to a bad copy / paste.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since the parent rate has been recalculated, pixel RCG clock
should rely on it to find the correct M/N values during set_rate,
instead of calling __clk_round_rate() to its parent again.
Signed-off-by: Hai Li <hali@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Fixes: 99cbd064b0 ("clk: qcom: Support display RCG clocks")
[sboyd@codeaurora.org: Silenced unused parent variable warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
intel_atomic_setup_scalers() dereferences 'plane' before the plane has
been assigned. The plane ID assignment doing this dereference is only
needed for debugging messages later in the function, so just move the
assignment farther down the function to a point where plane will no
longer be NULL.
This was introduced in:
commit 133b0d128b
Author: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Date: Mon Jun 15 12:33:39 2015 +0200
drm/i915: Clean up intel_atomic_setup_scalers slightly.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Reported-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Avoid casting variables to different sizes due to different
compilers and settings.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: qipeng.zha <qipeng.zha@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
In case kstrdup() fails the resources to release are
midi->in_port[] and midi. No cards have been registered,
so no need to unregister any.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Triggering suspend to RAM via sysfs on a i.MX28 causes a NULL pointer
dereference. This patch avoids the oops in mxs_phy_get_vbus_status()
by aborting since there is no syscon available.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: efdbd3a5d6 ("usb: phy: mxs: do not set PWD.RXPWD1PT1 for low speed connection")
CC: <stable@vger.kernel.org> # 4.0
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
My static checker detected the mistake. I fix this by changing "goto
err_irq" to "goto err_req". The label err_irq is not used now
so this patch also removes it.
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit f563d23090 ("usb: gadget: composite: add req_match method
to usb_function") accesses cdev->config even before set config
is invoked causing a NULL pointer dereferencing error while running
Lecroy Mass Storage Compliance test.
Fix it here by accessing cdev->config only if it is non NULL.
Fixes: commit f563d23090 ("usb: gadget: composite: add req_match
method to usb_function").
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
do not try to set cancel function in synchronous operations in
ffs_epfile_{read,write}_iter.
Cc: <stable@vger.kernel.org> # v4.0+
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Mass storage function created via configfs always reports eight LUNs
to the hosts even if only one LUN has been configured. Adjust the
number when the USB function is allocated based on LUNs that user
has created.
Cc: <stable@vger.kernel.org>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 3e10a2ce98 ("usb: dwc3: add hsphy_interface
property") introduced a possible NULL pointer
dereference because dwc->hsphy_interface can be
NULL.
In order to fix it, all we have to do is guard
strncmp() against a NULL argument.
Fixes: 3e10a2ce98 ("usb: dwc3: add hsphy_interface property")
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Register backup function can be called from atomic context. Instead
of using atomic memory pool, embed backup storage space in
struct dwc2_hsotg.
Also add a valid flag in each struct as NULL pointer can't be used as
the content validity check any more.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To avoid sleep while atomic bugs, allocate qtd before calling
dwc2_hcd_urb_enqueue. No need to pass mem_flags to
dwc2_hcd_urb_enqueue any more as no memory allocations are done in it.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
To avoid sleep while atomic bugs, allocate qh before calling
dwc2_hcd_urb_enqueue. qh pointer can be used directly now instead of
passing ep->hcpriv as double pointer.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, we're calling musb_start() twice for DRD ports
in some situations. This has been observed to cause enumeration
issues after suspend/resume cycles with AM335x.
In order to fix the problem, we just have to fix the check
on musb_has_gadget() so that it only returns true if
current mode is Host and ignore the fact that we have or
not a gadget driver loaded.
Fixes: ae44df2e21 (usb: musb: call musb_start() only once in OTG mode)
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org> # v3.11+
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Building allmodconfig for arch/cris currently fails with:
drivers/built-in.o: In function `board_staging_register_clock':
drivers/staging/board/board.c:131: undefined reference to `clk_add_alias'
make: *** [vmlinux] Error 1
The clk_add_alias lives in drivers/clk/clkdev.c and that file
is only compiled for CONFIG_CLKDEV_LOOKUP, so it would seem
we need to add a dependency on that.
Geert also reported seeing this in his build coverage:
There seems to be another missing dependency on OF_IRQ:
drivers/built-in.o: In function `board_staging_gic_fixup_resources':
(.init.text+0x21c2): undefined reference to `irq_create_of_mapping'
so we might as well fix that at the same time since it is
on the same line.
Cc: Magnus Damm <damm+renesas@opensource.se>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is specific driver for Intel Atom SoCs like BayTrail and
Braswell. Let's move it to dedicated folder and alleviate a
arch/x86/kernel burden.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Kumar P Mahesh <mahesh.kumar.p@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1436192944-56496-6-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The patch adds CHT PMC interface. This exposes all the South IP
device power states and S0ix states for CHT. The bit map of
FUNC_DIS and D3_STS_0 registers for SoCs are consistent. The
D3_STS_1 and FUNC_DIS_2 registers, however, are not aligned.
This is fixed by splitting a common mapping on per register basis.
(Originally based on code from Kumar P Mahesh.)
Originally-from: Kumar P Mahesh <mahesh.kumar.p@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Aubrey Li <aubrey.li@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rafael J . Wysocki <rafael.j.wysocki@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1436192944-56496-5-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This adds a power domain driver for the Mediatek SCPSYS unit.
The System Control Processor System (SCPSYS) has several power
management related tasks in the system. The tasks include thermal
measurement, dynamic voltage frequency scaling (DVFS), interrupt
filter and lowlevel sleep control. The System Power Manager (SPM)
inside the SCPSYS is for the MTCMOS power domain control.
For now this driver only adds power domain support, the more
advanced features are not yet supported. The driver implements
the generic PM domain device tree bindings, the first user will
most likely be the Mediatek AFE audio driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This adds documentation for the MediaTek SCPSYS unit found in MT8173 SoCs.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
