CEA defines 64 modes, indexed from 1 to 64. modedb has cea_modes arrays,
which contains 64 entries. However, the code uses the CEA indices
directly, i.e. the first mode is at cea_modes[1]. This means the array
is one too short.
This does not cause references to uninitialized memory as the code in
fbmon only allows indexes up to 63, and the cea_modes does not contain
an entry for the mode 64 so it could not be used in any case.
However, the code contains a check 'if (idx > ARRAY_SIZE(cea_modes)',
and while that check is a no-op as at that point idx cannot be >= 63, it
upsets static checkers.
Fix this by increasing the cea_array size to be 65, and change the code
to allow mode 64.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Sparse reports the following with regard to locking in the
tegra_dma_global_pause() and tegra_dma_global_resume() functions:
drivers/dma/tegra20-apb-dma.c:362:9: warning: context imbalance in
'tegra_dma_global_pause' - wrong count at exit
drivers/dma/tegra20-apb-dma.c:366:13: warning: context imbalance in
'tegra_dma_global_resume' - unexpected unlock
The warning is caused because tegra_dma_global_pause() acquires a lock
but does not release it. However, the lock is released by
tegra_dma_global_resume(). These pause/resume functions are called in
pairs and so it does appear to work.
This global pause is used on early tegra devices that do not have an
individual pause for each channel. The lock appears to be used to ensure
that multiple channels do not attempt to assert/de-assert the global pause
at the same time which could cause the DMA controller to be in the wrong
paused state. Rather than locking around the entire code between the pause
and resume, employ a simple counter to keep track of the global pause
requests. By using a counter, it is only necessary to hold the lock when
pausing and unpausing the DMA controller and hence, fixes the sparse
warning.
Please note that for devices that support individual channel pausing, the
DMA controller lock is not held between pausing and unpausing the channel.
Hence, this change will make the devices that use the global pause behave
in the same way, with regard to locking, as those that don't.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some void functions have unnecessary return statements at the end
(reported by sparse) and so remove these. Also remove the return variables
from functions tegra_dma_prep_slave_sg() and tegra_dma_prep_slave_cyclic()
because the value is not used.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Everytime a DMA channel register is accessed, the channel base address
is calculated by adding the DMA base address and the channel register
offset. Avoid this calculation and simply calculate the channel base
address once at probe time for each DMA channel.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The callback and callback_param members of the tegra_dma_sg_req structure
are never used. The dma-engine structure, dma_async_tx_descriptor, defines
the same members and these are the ones used by the driver. Therefore,
remove the unused versions from the tegra_dma_sg_req structure.
The half_done member of tegra_dma_channel structure is configured but
never used and so remove it.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simplify a trivial if-return sequence by combining it with a preceding
function call.
The semantic patch that makes this change is available in
scripts/coccinelle/misc/simple_return.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lucas Stach <l.stach@pengutronix.de>
Use BUG_ON() instead of an if condition followed by BUG().
The semantic patch that makes this change is available in
scripts/coccinelle/misc/bugon.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
dma_request_slave_channel_compat() is meant for drivers that support
both DT and legacy platform device based probing: if DT channel DMA
setup fails, it will fall back to platform data based DMA channel setup,
using hardcoded DMA channel IDs and a filter function.
However, if the DTS doesn't provide a "dmas" property for the device,
the fallback is also used. If the legacy filter function is not
hardcoded in the DMA slave driver, but comes from platform data, it will
be NULL. Then dma_request_slave_channel_compat() will succeed
incorrectly, and return a DMA channel, as a NULL legacy filter function
actually means "all channels are OK", not "do not match".
Later, when trying to use that DMA channel, it will fail with:
rcar-dmac e6700000.dma-controller: rcar_dmac_prep_slave_sg: bad parameter: len=1, id=-22
To fix this, ensure that both the filter function and the DMA channel ID
are not NULL before using the legacy fallback.
Note that some DMA slave drivers can handle this failure, and will fall
back to PIO.
See also commit 056f6c8702 ("dmaengine: shdma: Make dummy
shdma_chan_filter() always return false"), which fixed the same issue
for the case where shdma_chan_filter() is hardcoded in a DMA slave
driver.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There is no need to use the IS_ERR_VALUE() macro for checking the return
value from pm_runtime_* functions.
Test for a negative pm_runtime_get_sync() return value instead of using
IS_ERR_VALUE().
The semantic patch that makes this change is available in
scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
On powernv platform, IOV BAR would be shifted if necessary. While the log
message is not correct when disabling VFs.
This patch fixes this by print correct message based on the offset value.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If we open a context but do not start it (either because we do not attempt
to start it, or because it fails to start for some reason), we are left
with a context in state OPENED. Previously, cxl_release_context() only
allowed releasing contexts in state CLOSED, so attempting to release an
OPENED context would fail.
In particular, this bug causes available contexts to run out after some EEH
failures, where drivers attempt to release contexts that have failed to
start.
Allow releasing contexts in any state with a value lower than STARTED, i.e.
OPENED or CLOSED (we can't release a STARTED context as it's currently
using the hardware, and we assume that contexts in any new states which may
be added in future with a value higher than STARTED are also unsafe to
release).
Cc: stable@vger.kernel.org
Fixes: 6f7f0b3df6 ("cxl: Add AFU virtual PHB and kernel API")
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Daniel Axtens <dja@axtens.net>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
clk_enable() may fail, so we should better check the return value and
propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds support for the DMA engine present on Allwinner A10,
A13, A10S and A20 SoCs. This engine has two kinds of channels: normal
and dedicated. The main difference is in the mode of operation;
while a single normal channel may be operating at any given time,
dedicated channels may operate simultaneously provided there is no
overlap of source or destination.
Hardware documentation can be found on A10 User Manual (section 12), A13
User Manual (section 14) and A20 User Manual (section 1.12)
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Unlike the previous attempt, this takes into account the fact that
we may be calling it from the recovery thread itself. Detect this
by looking at what kind of open we're doing, and checking the state
of the NFS_DELEGATION_NEED_RECLAIM if it turns out we're doing a
reboot reclaim-type open.
Cc: Olga Kornievskaia <aglo@umich.edu>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Follow up to commit c4a7ca7749 ("SUNRPC: Allow waiting on memory
allocation"). Allows the RPC socket code to do non-IO blocking.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Add Alison and myself as maintainers of the Freescale DCU DRM driver.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
NEC represent NEC LCD Technologies, Ltd.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
This patch add support for Two Dimensional Animation and Compositing
Engine (2D-ACE) on the Freescale SoCs.
2D-ACE is a Freescale display controller. 2D-ACE describes
the functionality of the module extremely well its name is a value
that cannot be used as a token in programming languages.
Instead the valid token "DCU" is used to tag the register names and
function names.
The Display Controller Unit (DCU) module is a system master that
fetches graphics stored in internal or external memory and displays
them on a TFT LCD panel. A wide range of panel sizes is supported
and the timing of the interface signals is highly configurable.
Graphics are read directly from memory and then blended in real-time,
which allows for dynamic content creation with minimal CPU
intervention.
The features:
(1) Full RGB888 output to TFT LCD panel.
(2) Blending of each pixel using up to 4 source layers
dependent
on size of panel.
(3) Each graphic layer can be placed with one pixel resolution
in either axis.
(4) Each graphic layer support RGB565 and RGB888 direct colors
without alpha channel and BGRA8888 BGRA4444 ARGB1555 direct
colors
with an alpha channel and YUV422 format.
(5) Each graphic layer support alpha blending with 8-bit
resolution.
This is a simplified version, only one primary plane, one
framebuffer, one crtc, one connector and one encoder for TFT
LCD panel.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When CONFIG_LWTUNNEL config is not enabled, the lwtstate_free() is not
declared in lwtunnel.h at all. However, even in this case, the function
is still referenced in fib_semantics.c so that there appears the
following sparse warnings:
net/ipv4/fib_semantics.c:553:17: error: undefined identifier 'lwtstate_free'
CC net/ipv4/fib_semantics.o
net/ipv4/fib_semantics.c: In function ‘fib_encap_match’:
net/ipv4/fib_semantics.c:553:3: error: implicit declaration of function ‘lwtstate_free’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[1]: *** [net/ipv4/fib_semantics.o] Error 1
make: *** [net/ipv4/fib_semantics.o] Error 2
To eliminate the error, we define an empty function for lwtstate_free()
in lwtunnel.h when CONFIG_LWTUNNEL is disabled.
Fixes: df383e6240 ("lwtunnel: fix memory leak")
Cc: Jiri Benc <jbenc@redhat.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following PR add support for 3 more atmel SoCs and for some missing
features (new input formats and PRIME support).
* 'drm-atmel-hlcdc-devel' of https://github.com/bbrezillon/linux-at91:
drm: atmel-hlcdc: add support for sama5d4 SoCs
drm: atmel-hlcdc: add support for at91sam9n12 SoC
drm: atmel-hlcdc: add support for at91sam9x5 SoCs
drm: atmel-hlcdc: add RGB565 and RGB444 output support
drm: atmel-hlcdc: add the missing DRM_ATOMIC flag
drm: atmel-hlcdc: add PRIME support
Add a function to find the start of the SADs in the ELD. This
complements the helper to retrieve the SAD count.
[airlied: this fixes a build problem with the alsa eld helper
which required this].
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
amdgpu and radeon changes for 4.3. Highlights:
- Fiji support for amdgpu.
- CGS support for amdgpu. This is a new driver
internal cross-component API.
- Initial GPU scheduler for amdgpu. Still disabled
by default.
- Lots of bug fixes and optimizations
* 'drm-next-4.3' of git://people.freedesktop.org/~agd5f/linux: (130 commits)
drm/amdgpu: wait on page directory changes. v2
drm/amdgpu: Select BACKLIGHT_LCD_SUPPORT
drm/radeon: Select BACKLIGHT_LCD_SUPPORT
drm/amdgpu: cleanup sheduler rq handling v2
drm/amdgpu: move prepare work out of scheduler to cs_ioctl
drm/amdgpu: fix unnecessary wake up
drm/amdgpu: fix duplicated mapping invoke bug
drm/amdgpu: drop bo_list_clone when no scheduler
drm/amdgpu: disable GPU reset by default
drm/amdgpu: fix type mismatch error
drm/amdgpu: add reference for **fence
drm/amdgpu: fix waiting for all fences before flipping
drm/amdgpu: fix UVD return code checking
drm/amdgpu: remove scheduler fence list v2
drm/amdgpu: remove amd_sched_wait_emit v2
drm/amdgpu: remove unecessary scheduler fence callbacks
drm/amdgpu: fix scheduler fence implementation
drm/amdgpu: don't grab dev->struct_mutex in pm functions
drm/amdgpu: Don't take dev->struct_mutex in bo_force_delete
drm/radeon: Don't take dev->struct_mutex in pm functions
...
Fix CONFIG_LOCKDEP=n build, because asserts I put in to ensure we
aren't overrunning lockdep subclasses in commit 0952c81 ("xfs:
clean up inode lockdep annotations") use a define that doesn't
exist when CONFIG_LOCKDEP=n
Only check the subclass limits when lockdep is actually enabled.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Dave Chinner <david@fromorbit.com>
The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read after
an erase.
The issue is that in the interrupt handler, the status bits are cleared
after the new command is issued. There is a small temporal window where
this happens :
- the previous command has set the command done bit
- the ready for a command bit is set
- the handler submits the next command
- just then, the command completes, and the command done bit is still
set
- the handler clears the "previous" command done bit
- the handler exits
In this flow, the "command done" of the next command will never trigger
a new interrupt to finish the status command, as it was cleared for both
commands.
Fix this by clearing the status bit before submitting a new command.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The TI crossbar irqchip doesn't provides any facility to configure the
wakeup sources, but the conversion to hierarchical irqdomains set the
irq_set_wake callback to irq_chip_set_wake_parent. The parent chip
(OMAP wakeupgen) has no irq_set_wake function either so the call will
fail with -ENOSYS. As a result the irq_set_wake() call in the resume
path will trigger an 'Unbalanced wake disable' warning.
Before the conversion the GIC irqchip was the top level irqchip and
correctly flagged with IRQCHIP_SKIP_SET_WAKE.
Restore the correct behaviour by removing the irq_set_type callback
from the crossbar irqchip and set the IRQCHIP_SKIP_SET_WAKE flag which
lets the irq_set_irq_wake() call from the driver succeed.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-7-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ARM GIC requires that all interrupts which are not used as a
wakeup source have to be masked during suspend.
The conversion of the crossbar irqchip to hierarchical irq domains
failed to mark the crossbar irqchip with the IRQCHIP_MASK_ON_SUSPEND
flag and therefor broke the suspend requirement of the GIC.
Before the conversion the flags were visible because the GIC was the
top level irqchip. After the conversion the crossbar irqchip is the
top level irq chip whose flags are evaluated in suspend_device_irq().
As the flag is not set the masking of the non-wakeup irqs is not
invoked which breaks suspend.
Add the IRQCHIP_MASK_ON_SUSPEND flag to the crossbar irqchip, so the
GIC interrupts get masked properly.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-6-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The conversion of the wakeupgen irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The wakeupgen irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the wakeupgen irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 7136d457f3 ('ARM: omap: convert wakeupgen to stacked domains')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-5-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The conversion of the crossbar irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The crossbar irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the crossbar irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-4-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This helper is required for irq chips which do not implement a
irq_set_type callback and need to call down the irq domain hierarchy
for the actual trigger type change.
This helper is required to fix further wreckage caused by the
conversion of TI OMAP to hierarchical irq domains and therefor tagged
for stable.
[ tglx: Massaged changelog ]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-3-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_chip_retrigger_hierarchy() returns -ENOSYS if it was not able to
find at least one .irq_retrigger() callback implemented in the IRQ
domain hierarchy.
That's wrong, because check_irq_resend() expects a 0 return value from
the callback in case that the hardware assisted resend was not
possible. If the return value is non zero the core code assumes
hardware resend success and the software resend is not invoked.
This results in lost interrupts on platforms where none of the parent
irq chips in the hierarchy implements the retrigger callback.
This is observable on TI OMAP, where the hierarchy is:
ARM GIC <- OMAP wakeupgen <- TI Crossbar
Return 0 instead so the software resend mechanism gets invoked.
[ tglx: Massaged changelog ]
Fixes: 85f08c17de ('genirq: Introduce helper functions...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-2-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.
The bug is tricky : if the bootloader left a status bit set, the
unmasking of interrupts does trigger the interrupt handler before the
first command is issued, blocking the good behavior of the nand.
The same would happen if in pxa3xx_nand code flow a status bit is left,
and then a command is started.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We should not assume any particular hardware topology. Commit d0751b98df
("PCI: Add dev->has_secondary_link to track downstream PCIe links") relied
on the assumption that every PCIe hierarchy is rooted at a Root Port. But
we can't rely on any assumption about what hardware we will find; we just
have to deal with the world as it is.
On some platforms, PCIe devices (endpoints, switch upstream ports, etc.)
appear directly on the root bus, and there is no Root Port in the PCI bus
hierarchy. For example, Meelis observed these top-level devices on a
Sparc V245:
0000:02:00.0 PCI bridge to [bus 03-0d] Switch Upstream Port
0001:02:00.0 PCI bridge to [bus 03] PCIe to PCI/PCI-X Bridge
These devices *look* like they have links going upstream, but there really
are no upstream devices.
In set_pcie_port_type(), we used the parent device to figure out which side
of a switch port has a link, so if the parent device did not exist, we
dereferenced a NULL parent pointer.
Check whether the parent device exists before dereferencing it.
Meelis observed this oops on Sparc V245 and T2000. Ben Herrenschmidt says
this is also possible on IBM PowerVM guests on PowerPC.
[bhelgaas: changelog, comment]
Link: http://lkml.kernel.org/r/alpine.LRH.2.20.1508122118210.18637@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Removing unreachable code from nvme_abort_req as nvme_submit_cmd has no
failure status to return.
Signed-off-by: Sunad Bhandary <sunad.s@samsung.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
After enhancing arm64 FP/SIMD exit handling, ARMv7 VFP exit branch is moved
to guest trap handling. This allows us to keep exit handling flow between both
architectures consistent.
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
If we partially clone one extent of a file into a lower offset of the
file, fsync the file, power fail and then mount the fs to trigger log
replay, we can get multiple checksum items in the csum tree that overlap
each other and result in checksum lookup failures later. Those failures
can make file data read requests assume a checksum value of 0, but they
will not return an error (-EIO for example) to userspace exactly because
the expected checksum value 0 is a special value that makes the read bio
endio callback return success and set all the bytes of the corresponding
page with the value 0x01 (at fs/btrfs/inode.c:__readpage_endio_check()).
From a userspace perspective this is equivalent to file corruption
because we are not returning what was written to the file.
Details about how this can happen, and why, are included inline in the
following reproducer test case for fstests and the comment added to
tree-log.c.
seq=`basename $0`
seqres=$RESULT_DIR/$seq
echo "QA output created by $seq"
tmp=/tmp/$$
status=1 # failure is the default!
trap "_cleanup; exit \$status" 0 1 2 3 15
_cleanup()
{
_cleanup_flakey
rm -f $tmp.*
}
# get standard environment, filters and checks
. ./common/rc
. ./common/filter
. ./common/dmflakey
# real QA test starts here
_need_to_be_root
_supported_fs btrfs
_supported_os Linux
_require_scratch
_require_dm_flakey
_require_cloner
_require_metadata_journaling $SCRATCH_DEV
rm -f $seqres.full
_scratch_mkfs >>$seqres.full 2>&1
_init_flakey
_mount_flakey
# Create our test file with a single 100K extent starting at file
# offset 800K. We fsync the file here to make the fsync log tree gets
# a single csum item that covers the whole 100K extent, which causes
# the second fsync, done after the cloning operation below, to not
# leave in the log tree two csum items covering two sub-ranges
# ([0, 20K[ and [20K, 100K[)) of our extent.
$XFS_IO_PROG -f -c "pwrite -S 0xaa 800K 100K" \
-c "fsync" \
$SCRATCH_MNT/foo | _filter_xfs_io
# Now clone part of our extent into file offset 400K. This adds a file
# extent item to our inode's metadata that points to the 100K extent
# we created before, using a data offset of 20K and a data length of
# 20K, so that it refers to the sub-range [20K, 40K[ of our original
# extent.
$CLONER_PROG -s $((800 * 1024 + 20 * 1024)) -d $((400 * 1024)) \
-l $((20 * 1024)) $SCRATCH_MNT/foo $SCRATCH_MNT/foo
# Now fsync our file to make sure the extent cloning is durably
# persisted. This fsync will not add a second csum item to the log
# tree containing the checksums for the blocks in the sub-range
# [20K, 40K[ of our extent, because there was already a csum item in
# the log tree covering the whole extent, added by the first fsync
# we did before.
$XFS_IO_PROG -c "fsync" $SCRATCH_MNT/foo
echo "File digest before power failure:"
md5sum $SCRATCH_MNT/foo | _filter_scratch
# Silently drop all writes and ummount to simulate a crash/power
# failure.
_load_flakey_table $FLAKEY_DROP_WRITES
_unmount_flakey
# Allow writes again, mount to trigger log replay and validate file
# contents.
# The fsync log replay first processes the file extent item
# corresponding to the file offset 400K (the one which refers to the
# [20K, 40K[ sub-range of our 100K extent) and then processes the file
# extent item for file offset 800K. It used to happen that when
# processing the later, it erroneously left in the csum tree 2 csum
# items that overlapped each other, 1 for the sub-range [20K, 40K[ and
# 1 for the whole range of our extent. This introduced a problem where
# subsequent lookups for the checksums of blocks within the range
# [40K, 100K[ of our extent would not find anything because lookups in
# the csum tree ended up looking only at the smaller csum item, the
# one covering the subrange [20K, 40K[. This made read requests assume
# an expected checksum with a value of 0 for those blocks, which caused
# checksum verification failure when the read operations finished.
# However those checksum failure did not result in read requests
# returning an error to user space (like -EIO for e.g.) because the
# expected checksum value had the special value 0, and in that case
# btrfs set all bytes of the corresponding pages with the value 0x01
# and produce the following warning in dmesg/syslog:
#
# "BTRFS warning (device dm-0): csum failed ino 257 off 917504 csum\
# 1322675045 expected csum 0"
#
_load_flakey_table $FLAKEY_ALLOW_WRITES
_mount_flakey
echo "File digest after log replay:"
# Must match the same digest he had after cloning the extent and
# before the power failure happened.
md5sum $SCRATCH_MNT/foo | _filter_scratch
_unmount_flakey
status=0
exit
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
While we are committing a transaction, it's possible the previous one is
still finishing its commit and therefore we wait for it to finish first.
However we were not checking if that previous transaction ended up getting
aborted after we waited for it to commit, so we ended up committing the
current transaction which can lead to fs corruption because the new
superblock can point to trees that have had one or more nodes/leafs that
were never durably persisted.
The following sequence diagram exemplifies how this is possible:
CPU 0 CPU 1
transaction N starts
(...)
btrfs_commit_transaction(N)
cur_trans->state = TRANS_STATE_COMMIT_START;
(...)
cur_trans->state = TRANS_STATE_COMMIT_DOING;
(...)
cur_trans->state = TRANS_STATE_UNBLOCKED;
root->fs_info->running_transaction = NULL;
btrfs_start_transaction()
--> starts transaction N + 1
btrfs_write_and_wait_transaction(trans, root);
--> starts writing all new or COWed ebs created
at transaction N
creates some new ebs, COWs some
existing ebs but doesn't COW or
deletes eb X
btrfs_commit_transaction(N + 1)
(...)
cur_trans->state = TRANS_STATE_COMMIT_START;
(...)
wait_for_commit(root, prev_trans);
--> prev_trans == transaction N
btrfs_write_and_wait_transaction() continues
writing ebs
--> fails writing eb X, we abort transaction N
and set bit BTRFS_FS_STATE_ERROR on
fs_info->fs_state, so no new transactions
can start after setting that bit
cleanup_transaction()
btrfs_cleanup_one_transaction()
wakes up task at CPU 1
continues, doesn't abort because
cur_trans->aborted (transaction N + 1)
is zero, and no checks for bit
BTRFS_FS_STATE_ERROR in fs_info->fs_state
are made
btrfs_write_and_wait_transaction(trans, root);
--> succeeds, no errors during writeback
write_ctree_super(trans, root, 0);
--> succeeds
--> we have now a superblock that points us
to some root that uses eb X, which was
never written to disk
In this scenario future attempts to read eb X from disk results in an
error message like "parent transid verify failed on X wanted Y found Z".
So fix this by aborting the current transaction if after waiting for the
previous transaction we verify that it was aborted.
Cc: stable@vger.kernel.org
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <clm@fb.com>
The SG_GAPS queue flag caused checks for bio vector alignment against
PAGE_SIZE, but the device may have different constraints. This patch
adds a queue limits so a driver with such constraints can set to allow
requests that would have been unnecessarily split. The new gaps check
takes the request_queue as a parameter to simplify the logic around
invoking this function.
This new limit makes the queue flag redundant, so removing it and
all usage. Device-mappers will inherit the correct settings through
blk_stack_limits().
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch only saves and restores FP/SIMD registers on Guest access. To do
this cptr_el2 FP/SIMD trap is set on Guest entry and later checked on exit.
lmbench, hackbench show significant improvements, for 30-50% exits FP/SIMD
context is not saved/restored
[chazy/maz: fixed save/restore logic for 32bit guests]
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
alloc_btrfs_bio relies on GFP_NOFS allocation when committing the
transaction but this allocation context is rather weak wrt. reclaim
capabilities. The page allocator currently tries hard to not fail these
allocations if they are small (<=PAGE_ALLOC_COSTLY_ORDER) but it can
still fail if the _current_ process is the OOM killer victim. Moreover
there is an attempt to move away from the default no-fail behavior and
allow these allocation to fail more eagerly. This would lead to:
[ 37.928625] kernel BUG at fs/btrfs/extent_io.c:4045
which is clearly undesirable and the nofail behavior should be explicit
if the allocation failure cannot be tolerated.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Chris Mason <clm@fb.com>
Following arguments are not used in tree-log.c:
insert_one_name(): path, type
wait_log_commit(): trans
wait_for_writer(): trans
This patch remove them.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
