It's required for accessing trx header (usually re-calculating a
checksum) and for writing a new firmware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Add support for GigaDevice GD25Q32 32 Mbit (4 MB) SPI Flash (see datasheet:
http://www.gigadevice.com/UserFiles/GD25Q32_Rev0.2(1).pdf) used in Hame MPR-A1
and clones, and for GigaDevice GD25Q64 64 Mbit (8 MB) SPI Flash used in
Hame MPR-A2 devices (datasheet: http://www.gigadevice.com/UserFiles/GD25Q64.pdf).
Signed-off-by: Michel Stempin <michel.stempin@wanadoo.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
ELM module can be used for hardware error correction of BCH 4 & 8 bit.
ELM module functionality is verified by checking the availability of
handle for ELM module in device tree. Hence supporting
1. ELM module available, BCH error correction done by ELM module. Also
support read & write page in one shot by adding custom read_page and
write_page methods. This helps in optimizing code for NAND flashes with
page size less than 4 KB.
2. If ELM module not available fall back to software BCH error
correction support.
New structure member is added to omap_nand_info
1. "is_elm_used" to know the status of whether the ELM module is used for
error correction or not.
2. "elm_dev" device pointer to elm device on detection of ELM module.
Also being here update the device tree documentation of gpmc-nand for
adding optional property elm_id.
Note:
ECC layout uses 1 extra bytes for 512 byte of data to handle erased
pages. Extra byte programmed to zero for programmed pages. Also BCH8
requires 14 byte ecc to maintain compatibility with RBL ECC layout.
This results a common ecc layout across RBL, U-boot & Linux with BCH8.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme
error correction.
For now only 4 & 8 bit support is added
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Remove check of ecc bytes with 13, number of errors can directly update
from nand ecc strength. This will increase re-usability of the code.
Also add macro definitions BCH8_ERROR_MAX & BCH4_ERROR_MAX for better
readability and cleaner code.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Also compress the id in case of a v3 NAND flash controller (i.mx51, i.mx53)
and 16Bit buswidth.
Signed-off-by: Roman Schneider <schneider@at.festo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch adds generic support for flash protection on STmicro chips.
On chips with less than 3 protection bits, the unused bits are don't cares
and so can be written anyway. The lock function will only change the
protection bits if it would not unlock other areas. Similarly, the unlock
function will not lock currently unlocked areas. Tested on the m25p64.
Signed-off-by: Austin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use more preferable function name which implies using a pseudo-random
number generator.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
/proc/mtd doesn't contain the mtd-id of the device, but the part name from the
command line. This corrects what I believe is an obsolete comment from commit
a0ee24a03b.
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Cc: Philip Rakity <prakity@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The mtd documentation makes no mention of the useful feature whereby
partitions' logical ordering need not match their physical ordering.
Truncation of parts, skipping of zero sized parts, and handling of
overlapping parts are similarly not mentioned.
This updates the comments at the top of file describing the command
line parsing as currently implemented. I proposed this in
http://lists.infradead.org/pipermail/linux-mtd/2012-December/045314.html
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Perform flash size truncation before skipping zero sized partition
so that if the result is a zero sized, it will be skipped like the
others.
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Acked-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Decrement index i after skipping a zero sized partition. On next loop
iteration, the index will be the same as before, but the data will be
new as it was moved when earlier partition was skipped.
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Acked-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Always report corrected and failed ECC stats back up to the MTD layer. Also
return max_bitflips from read_page() as is expected from NAND drivers now.
Signed-off-by: Zach Sadecki <zsadecki@itwatchdogs.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Fix missing dependency which can cause a build error such
as: ERROR: "byte_rev_table" [drivers/mtd/devices/docg3.ko]
undefined!
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit cdeadd712f (mtd: nand: davinci: add OF
support for davinci nand controller) has never been really build tested with
the driver as a module. When the driver is built-in, the missing semicolon
after structure initializer is "compensated" by MODULE_DEVICE_TABLE() macro
being empty and so the initializer using the trailing semicolon on the next
line; when the driver is built as a module, compilation error ensues, and as
the 'davinci_all_defconfig' has the NAND driver modular, this error prevents
DaVinci family kernel from building...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org # 3.7
Pull powerpc update from Benjamin Herrenschmidt:
"Just so that you don't get too bored on your Island here's a patch for
3.8 fixing a nasty bug that affects the new 64T support that was
merged in 3.7. Please apply whenever you have a chance (and an
internet connection!)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix hash computation function
Pull radeon fixes from Dave Airlie:
"I got these late last week, the main chunks of these fix a rendering
regression since 3.7, and the settle ones all fix the issue where we
don't wait long enough for the memory controller to settle after
turning it off which causes bad memory reads, they all fix real users
bugs, and most of them are destined for stable.
Can't remember if you had net connection on that island :-)"
I don't know if the "two tin-cans and a string" thing here on "that
island" can really be considered internet, but I guess I can pull
things. Barely.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: switch back to the CP ring for VM PT updates
drm/radeon: prevent crash in the ring space allocation
drm/radeon: Calling object_unrefer() when creating fb failure
drm/radeon/r5xx-r7xx: wait for the MC to settle after MC blackout
drm/radeon/evergreen+: wait for the MC to settle after MC blackout
drm/radeon: protect against div by 0 in backend setup
drm/radeon: fix backend map setup on 1 RB sumo boards
drm/radeon: add quirk for RV100 board
drm/radeon: add WAIT_UNTIL to the non-VM safe regs list for cayman/TN
drm/radeon: fix MC blackout on evergreen+
The ASM version of hash computation function was truncating the upper bit.
Make the ASM version similar to hpt_hash function. Remove masking vsid bits.
Without this patch, we observed hang during bootup due to not satisfying page
fault request correctly. The fault handler used wrong hash values to update
the HPTE. Hence we kept looping with page fault.
hash_page(ea=000001003e260008, access=203, trap=300 ip=3fff91787134 dsisr 42000000
The computed value of hash 000000000f22f390
update: avpnv=4003e46054003e00, hash=000000000722f390, f=80000006, psize: 2 ...
BenH: The over-masking has been there for ever but only hurts with the
new 64T support introduced in 3.7
Reported-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Tested-by: Mike Qiu <qiudayu@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.7]
note that due to historical accident we do *not* directly take
generic versions - need to check and invert the sign of signal
number first.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
note that while struct compat_sigaction is the generic one, syscall
itself *isn't* - different arguments. IOW, CONFIG_ODD_RT_SIGACTION
stays.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
FW_STATUS_ABORT can be set only during the user-helper invocation,
thus we can ignore the check when CONFIG_HW_LOADER_USER_HELPER is
disabled.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By shuffling the code, reduce a few ifdefs in firmware_class.c.
Also, firmware_buf fmt field is changed to is_pages_buf boolean for
simplification.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new kconfig, CONFIG_FW_LOADER_USER_HELPER, and
guards the user-helper codes in firmware_class.c with ifdefs.
Yeah, yeah, there are lots of ifdefs in this patch. The further
clean-up with code shuffling follows in the next.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 3.7 kernel, the firmware loader can read the firmware files
directly, and the traditional user-mode helper is invoked only as a
fallback. This seems working pretty well, and the next step would be
to reduce the redundant user-mode helper stuff in future.
This patch is a preparation for that: refactor the code for splitting
user-mode helper stuff more easily. No functional change.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bus_type has a list of devices (klist_devices), but the list and the
subsys_private structure that contains it are not initialized until the
bus_type is registered with bus_register().
The panic/reboot path has fixups that look up devices in pci_bus_type. If
we panic before registering pci_bus_type, the bus_type exists but the list
does not, so mach_reboot_fixups() trips over a null pointer and panics
again:
mach_reboot_fixups
pci_get_device
..
bus_find_device(&pci_bus_type, ...)
bus->p is NULL
Joonsoo reported a problem when panicking before PCI was initialized.
I think this patch should be sufficient to replace the patch he posted
here: https://lkml.org/lkml/2012/12/28/75 ("[PATCH] x86, reboot: skip
reboot_fixups in early boot phase")
Reported-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) User of zram normally do mkfs.xxx or mkswap before using
the zram block device(ex, normally, do it at booting time)
It ends up allocating such metadata of zram before real usage so
benefit of lazy initialzation would be mitigated.
2) Some user want to use zram when memory pressure is high.(ie, load zram
dynamically, NOT booting time). It does make sense because people don't
want to waste memory until memory pressure is high(ie, where zram is really
helpful time). In this case, lazy initialzation could be failed easily
because we will use GFP_NOIO instead of GFP_KERNEL for avoiding deadlock.
So the benefit of lazy initialzation would be mitigated, too.
3) Metadata overhead is not critical and Nitin has a plan to diet it.
4K : 12 byte(64bit machine) -> 64G : 192M so 0.3% isn't big overhead
If insane user use such big zram device up to 20, it could consume 6% of ram
but efficieny of zram will cover the waste.
So this patch gives up lazy initialization and instead we initialize metadata
at disksize setting time.
Acked-by: Jerome Marchand <jmarchand@redhat.com>
Acked-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now zram document syas "set disksize is optional"
but partly it's wrong. When you try to use zram firstly after
booting, you must set disksize, otherwise zram can't work because
zram gendisk's size is 0. But once you do it, you can use zram freely
after reset because reset doesn't reset to zero paradoxically.
So in this time, disksize setting is optional.:(
It's inconsitent for user behavior and not straightforward.
This patch forces always setting disksize firstly before using zram.
Yes. It changes current behavior so someone could complain when
he upgrades zram. Apparently it could be a problem if zram is mainline
but it still lives in staging so behavior could be changed for right
way to go. Let them excuse.
Acked-by: Jerome Marchand <jmarchand@redhat.com>
Acked-by: Nitin Gupta <ngupta@vflare.org>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now zram allocates new page with GFP_KERNEL in zram I/O path
if IO is partial. Unfortunately, It may cause deadlock with
reclaim path like below.
write_page from fs
fs_lock
allocation(GFP_KERNEL)
reclaim
pageout
write_page from fs
fs_lock <-- deadlock
This patch fixes it by using GFP_NOIO. In read path, we
reorganize code flow so that kmap_atomic is called after the
GFP_NOIO allocation.
Cc: stable@vger.kernel.org
Acked-by: Jerome Marchand <jmarchand@redhat.com>
Acked-by: Nitin Gupta <ngupta@vflare.org>
[ penberg@kernel.org: don't use GFP_ATOMIC ]
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a number of pci vendor ids that are used in multiple
drivers in the comedi subsystem. Move these ids to pci_ids.h.
This also fixes some build warnings reported by the kbuild test
robot about PCI_VENDOR_ID_AMPLICON being undeclared.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting
meaningful output from a Lab-PC+ in differential mode for AI cmds, but
AI insn reads gave correct readings. He tracked it down to two
problems, one of which is addressed by this patch.
It seems the setting of the channel bits for particular scanning modes
was incorrect for differential mode. (Only half the number of channels
are available in differential mode; comedi refers to them as channels 0,
1, 2 and 3, but the hardware documentation refers to them as channels 0,
2, 4 and 6.) In differential mode, the setting of the channel enable
bits in the command1 register should depend on whether the scan enable
bit is set. Effectively, we need to double the comedi channel number
when the scan enable bit is not set in differential mode. The scan
enable bit gets set when the AI scan mode is `MODE_MULT_CHAN_UP` or
`MODE_MULT_CHAN_DOWN`, and gets cleared when the AI scan mode is
`MODE_SINGLE_CHAN` or `MODE_SINGLE_CHAN_INTERVAL`. The existing test
for whether the comedi channel number needs to be doubled in
differential mode is incorrect in `labpc_ai_cmd()`. This patch corrects
the test.
Thanks to Tuomas for suggesting the fix.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: <stable@vger.kernel.org> # 3.7.x, 3.8.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tuomas <tvainikk _at_ gmail _dot_ com> reported problems getting
meaningful output from a Lab-PC+ in differential mode for AI cmds, but
AI insn reads gave correct readings. He tracked it down to two
problems, one of which is addressed by this patch.
It seems that writing to the command3 register after writing to the
command4 register in `labpc_ai_cmd()` messes up the differential
reference bit setting in the command4 register. Set up the command4
register after the command3 register (as in `labpc_ai_rinsn()`) to avoid
the problem.
Thanks to Tuomas for suggesting the fix.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: <stable@vger.kernel.org> # 3.7.x, 3.8.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't allow comedi drivers to change `dev->hw_dev` using
`comedi_set_hw_dev()` if it's already been set. Return `-EEXIST` in
that case.
`dev->hw_dev` needs to be set to NULL by the core during clean-up of the
comedi device, so add a local function `comedi_clear_hw_dev()` to do
that.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chnage the inline `comedi_set_hw_dev()` to an exported function and
change it's return type from `void` to `int` so we can impose some
restrictions (in a later patch) and return an error if necessary.
Only a few comedi drivers call this, although they don't need to if the
hardware device has been attached automatically via
`comedi_auto_config()` and the comedi driver's `auto_attach()` method.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
`comedi_alloc_subdevice_minor()` doesn't really need a parameter
pointing to a `struct comedi_device` as it can get this information from
the parameter pointing to a `struct comedi_subdevice`. Just pass the
subdevice parameter.
Signed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the declarations of `comedi_alloc_subdevice_minor()` and
`comedi_free_subdevice_minor()` from "comedidev.h" to
"comedi_internal.h" since they are only of interest to the comedi core,
and are not exported to the low-level comedi drivers.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix all 'please, no space before tabs' warning found by checkpatch.pl
Signed-off-by: Garrick He <garrickhe@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split the bus specific ISA/PC-104 and PCI code out of this driver
and create two new drivers, das08_isa and das08_pci.
This allows removing all the #ifdef'ery in the das08 driver that
handled if the CONFIG_COMEDI_DAS08_{ISA,PCI} options were enabled.
It also makes the PCI driver cleanly Plug-and-Play since the comedi
driver only has an auto_attach callback. Previously it also had an
attach callback in order to handle the ISA cards.
Since the PCMCIA support was already split out, we can also remove
the now unused enum das08_bustype and it's use in the boardinfo.
The bus specific code deals with the bustype automatically before
it calls the common attach function in das08.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resolved 'do not use C99 // comments' checkpatch errors.
Many warnings about odd indentation were left.
Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleared 'do not use C99 // comments' checkpatch error in device.h and
device_cfg.h
Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleared 'do not use C99 // comments' checkpatch error, several warnings
about code indentation and camel casing were not resolved.
Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleared 'do not use C99 // comments' checkpatch errors in two headers.
Several obvious comments were removed.
Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switched // comments into respective /**/ ones
Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
switched all // comments on file to respective /**/
Signed-off-by: Andres More <more.andres@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert this pcmcia driver to the comedi auto attach mechanism.
This allows getting rid of the "hack" needed to pass the pcmcia_device
pointer from the pcmcia_driver to the comedi_driver.
We still need the boardinfo because ni_mio_common.c uses it. Cleanup
ni_getboardtype() so it returns a pointer to the boardinto instead
of the index.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
