This reverts commit 25b8d31488.
While the commit fixes multiple init_module definition error with
module build, it breaks build when both imx-pcm-fiq and imx-pcm-dma
are built in as below.
LD sound/soc/fsl/snd-soc-fsl-ssi.o
LD sound/soc/fsl/snd-soc-fsl-utils.o
LD sound/soc/fsl/snd-soc-imx-ssi.o
LD sound/soc/fsl/snd-soc-imx-audmux.o
LD sound/soc/fsl/snd-soc-imx-pcm-fiq.o
LD sound/soc/fsl/snd-soc-imx-pcm-dma.o
LD sound/soc/fsl/snd-soc-eukrea-tlv320.o
LD sound/soc/fsl/snd-soc-imx-sgtl5000.o
LD sound/soc/fsl/snd-soc-imx-mc13783.o
LD sound/soc/fsl/built-in.o
sound/soc/fsl/snd-soc-imx-pcm-dma.o: In function `imx_pcm_free':
imx-pcm.c:(.text+0x464): multiple definition of `imx_pcm_free'
sound/soc/fsl/snd-soc-imx-pcm-fiq.o:imx-pcm-fiq.c:(.text+0x1a8): first defined here
sound/soc/fsl/snd-soc-imx-pcm-dma.o: In function `snd_imx_pcm_mmap':
imx-pcm.c:(.text+0x35c): multiple definition of `snd_imx_pcm_mmap'
sound/soc/fsl/snd-soc-imx-pcm-fiq.o:imx-pcm-fiq.c:(.text+0xa0): first defined here
sound/soc/fsl/snd-soc-imx-pcm-dma.o: In function `imx_pcm_new':
imx-pcm.c:(.text+0x3dc): multiple definition of `imx_pcm_new'
sound/soc/fsl/snd-soc-imx-pcm-fiq.o:imx-pcm-fiq.c:(.text+0x120): first defined here
make[4]: *** [sound/soc/fsl/built-in.o] Error 1
Let's revert the commit and find a proper fix for multiple init_module
definition error later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The largest jumbo frame supported by the 82579 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A couple of board updates for PXA, from Haojian Zhuang.
* 'armsoc/board' of git://github.com/hzhuang1/linux:
ARM: pxa: pxa27x.c: add dummy SA1100 rtc clock
ARM: palmtreo: replace #if defined with IF_ENABLED
ARM: palmtreo: add docg4 device initialization
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove the function e1000e_commit_phy() and replace the few calls to it
with the same function pointer that it would call. The function pointer is
almost always set for the devices that access these code paths so there is
no risk of a NULL pointer dereference; for the few instances where the
function pointer might not be set (i.e. can be called for the few devices
which do not have this function pointer set), check for a valid function
pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Non-critical fixes for PXA, from Haojian Zhuang.
* 'armsoc/fix' of git://github.com/hzhuang1/linux:
ARM: pxa: Minor naming fixes in spitz.c
ARM: PXA3xx: program the CSMSADRCFG register
ARM: palmtreo: fix #ifdefs for leds-gpio device
ARM: palmtreo: fix lcd initilialization on treo680
Signed-off-by: Olof Johansson <olof@lixom.net>
A couple of PXA fixes that aren't critical enough for 3.9. From Haojian
Zhuang.
* 'armsoc/fix' of git://github.com/hzhuang1/linux:
ARM: pxa: Minor naming fixes in spitz.c
ARM: PXA3xx: program the CSMSADRCFG register
ARM: palmtreo: fix #ifdefs for leds-gpio device
ARM: palmtreo: fix lcd initilialization on treo680
Signed-off-by: Olof Johansson <olof@lixom.net>
Remove the function e1000_get_cable_length() and replace the two calls
to it with the same function pointer that it would call.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_get_phy_cfg_done() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In keeping with the e1000e driver function naming convention, the subject
function is renamed to indicate it is generic, i.e. it is applicable to
more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_force_speed_duplex() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
- remove unneeded includes due to DT conversion
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ8epEAAoJEAi3KVZQDZAetCIH/3WHUybBeOBxhRJpQb5YAJSC
LB+wFE/8RcHa5fcWb7JrEdTGXXia8IleflQFt0mOOvygoevNP0B/h4qQlEI0zh2f
ZFnHz8CYKtm8N0lztns+pC786l8I+lTmbqUfh4dHYfsyCyoggTVnujYHVAVcC868
VmhkROqPfY1NoSK8GOCHEhmQWYH7EXSYmBtnEzv5ZINTddNYJlUbLF6dHhXpYnoj
qn6PaBnW66sJupMUNvA3w0rVZpT5z7tPXzVdVUL0NYFufA4cbT/av6IJpIlNRndb
5cKvd79faAuANSw9OgVnCgnmgn34fSLH5xki3W6edpdtJtI1+sTkcxd9M/9xIms=
=k7vV
-----END PGP SIGNATURE-----
Merge tag 'cleanup_for_v3.9' of git://git.infradead.org/users/jcooper/linux into next/cleanup
From Jason Cooper:
mvebu cleanup for v3.9
- remove unneeded includes due to DT conversion
* tag 'cleanup_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood: Cleanup unneeded include files
arm: kirkwood: dockstar: remove useless include of SDIO header
Signed-off-by: Olof Johansson <olof@lixom.net>
Replace the function e1000_set_d0_lplu_state() with the contents of it
coded in place of the single call to the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pravin Shelar mentioned that GSO could potentially generate
wrong TX checksum if skb has fragments that are overwritten
by the user between the checksum computation and transmit.
He suggested to linearize skbs but this extra copy can be
avoided for normal tcp skbs cooked by tcp_sendmsg().
This patch introduces a new SKB_GSO_SHARED_FRAG flag, set
in skb_shinfo(skb)->gso_type if at least one frag can be
modified by the user.
Typical sources of such possible overwrites are {vm}splice(),
sendfile(), and macvtap/tun/virtio_net drivers.
Tested:
$ netperf -H 7.7.8.84
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
7.7.8.84 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3959.52
$ netperf -H 7.7.8.84 -t TCP_SENDFILE
TCP SENDFILE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.8.84 ()
port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3216.80
Performance of the SENDFILE is impacted by the extra allocation and
copy, and because we use order-0 pages, while the TCP_STREAM uses
bigger pages.
Reported-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull-request for net-next/master. There is are 9 patches by
Fabio Baltieri and Kurt Van Dijck which add LED infrastructure and
support for CAN devices. Bernd Krumboeck adds a driver for the USB CAN
adapter from 8 devices. Oliver Hartkopp improves the CAN gateway
functionality. There are 4 patches by me, which clean up the CAN's
Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.
This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.
Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock->sk_dst_cache is protected by RCU.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock->sk_dst_cache is protected by RCU, therefore we should
use __sk_dst_get() to deref it once we lock the sock.
This fixes several sparse warnings.
Cc: linux-decnet-user@lists.sourceforge.net
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
filters_lock might have been used while it was re-initialized.
Moved filters_lock and filters_list initialization to init_netdev instead of
alloc_resources which is called every time the device is configured.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible race where the TX completion handler can clean the
entire TX queue between the decision that the queue is full and actually
closing it. To avoid this situation, check again if the queue is really
full, if not, reopen the transmit and continue with sending the packet.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 (success) when in fact we are aborting the load, leads to kernel
panic when unloading the module. Fix that by returning the actual error code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device multicast list is protected by netif_addr_lock_bh in the networking core, we should
use this locking practice in mlx4_en too.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is stopped and flow steering mode is not device managed: promisc QP
rule wasn't removed from MCG table.
Added code to remove it in all flow steering modes.
In addition, promsic rule removal should be in stop port and not in start
port - moved it accordingly.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing the DUMP_ETH_STATS firmware command outside the lock leads to kernel
panic when data structures such as RX/TX rings are freed in parallel, e.g when
one changes the mtu or ring sizes.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to IP_GRE GSO support, GRE can recieve non linear skb which
results in panic in case of GRE_CSUM. Following patch fixes it by
using correct csum API.
Bug introduced in commit 6b78f16e4b (gre: add GSO support)
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the PIO mode and mixed PIO/DMA mode support. The mixed
PIO/DMA is the default mode of operation. This shall leverage overhead
that the driver creates due to setting up DMA descriptors even for very
short transfers.
The current boundary between PIO/DMA 8 bytes, transfers shorter than 8
bytes are transfered by PIO, longer transfers use DMA. The performance
of write transfers remains unchanged, while there is a minor improvement
of read performance. Reading 16KB EEPROM with DMA-only operations gives
a read speed of 39.5KB/s, while with then new mixed-mode the speed is
blazing 40.6KB/s.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
err_cpufreq label is now used only once. It can be removed and related
code can be moved to the caller location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In i2c-s3c2410 driver probe, only s3c24xx_i2c_init() needs the I2C clock
to be enabled. Moving clk_prepare_enable() and clk_disable_unprepare()
calls to around this function simplifies the return path of probe call.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
i2c-s3c2410 driver is modified to use devm_clk_get()
and devm_request_irq(). This also simplifies the
return path in driver's probe.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
err_noclk label redirects to a simple return statement. Move the
return statement to the caller location and remove the label.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
cppcheck rightfully reports those as "reassigned a value before the old
one has been used."
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Amend the I2C nomadik pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an i2c transfer
- "idle" after initial default, after resume default, and after each
i2c xfer
- "sleep" on suspend()
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle, and for runtime cases inbetween
I2C transfers.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[wsa: fixed braces on one else-branch]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
NVIDIA's Tegra114 has following enhanced feature in i2c controller:
- Enable/disable control for per packet transfer complete interrupt.
Earlier SoCs could not disable this.
- Single clock source for standard/fast and HS mode clock speed.
The clock divisor for fast/standard mode is added into the i2c
controller to meet the HS and standard/fast mode of clock speed
from single source.
Add support for the above feature to make it functional on T114 SOCs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Intel Lynxpoint has two I2C controllers. These controllers are enumerated
from ACPI namespace with IDs INT33C2 and INT33C3. Add support for these to
the I2C DesignWare platform driver.
This is based on the work of Dirk Brandewie.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In order to save power the device should be put to low power states
whenever it is not being used. We implement this by enabling minimal
runtime PM support.
There isn't much to do for the device itself as it is disabled once the
last transfer is completed but subsystem/domain runtime PM hooks can save
more power by power gating the device etc.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
If IC_EMPTYFIFO_HOLD_MASTER_EN is set to one, the DesignWare I2C controller
doesn't generate STOP on the bus when the FIFO is empty. This violates the
rules of Linux I2C stack as it requires that the STOP is issued once the
i2c_transfer() is finished.
However, there is no way to detect this from the hardware registers, so we
must make sure that the STOP bit is always set once the last byte of the
last message is transferred.
This patch is based on the work of Dirk Brandewie.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
avoid these checkpatch.pl issues :
- ERROR: "foo * bar" should be "foo *bar"
- ERROR: switch and case should be at the same indent
- ERROR: "(foo*)" should be "(foo *)"
- ERROR: do not use assignment in if condition
- ERROR: space required before the open parenthesis '('
- WARNING: suspect code indent for conditional statements
- WARNING: quoted string split across lines
- WARNING: space prohibited between function name and open parenthesis '('
- WARNING: line over 80 characters
also add spaces around some "+", "=", "*"
Signed-off-by: Laurent Navet <laurent.navet@gmail.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
As the at24 driver is able handle a bunch of serial storage chips other than
EEPROMs this is now mentioned in Kconfig.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
i2c_smbus_process_call has no users in the kernel, so this can be
removed. Documentation for the same has been updated accordingly.
Fixes following sparse warning.
drivers/i2c/i2c-core.c:1871:5: warning: symbol 'i2c_smbus_process_call'
was not declared. Should it be static?
[wsa: updated the documentation]
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
We have historically hard-coded entry points in head.S just so it's easy
to build the executable/bzImage headers with references to them.
Unfortunately, this leads to boot loaders abusing these "known" addresses
even when they are *explicitly* told that they "should look at the ELF
header to find this address, as it may change in the future". And even
when the address in question *has* actually been changed in the past,
without fanfare or thought to compatibility.
Thus we have bootloaders doing stunningly broken things like jumping
to offset 0x200 in the kernel startup code in 64-bit mode, *hoping*
that startup_64 is still there (it has moved at least once
before). And hoping that it's actually a 64-bit kernel despite the
fact that we don't give them any indication of that fact.
This patch should hopefully remove the temptation to abuse internal
addresses in future, where sternly worded comments have not sufficed.
Instead of having hard-coded addresses and saying "please don't abuse
these", we actually pull the addresses out of the ELF payload into
zoffset.h, and make build.c shove them back into the right places in
the bzImage header.
Rather than including zoffset.h into build.c and thus having to rebuild
the tool for every kernel build, we parse it instead. The parsing code
is small and simple.
This patch doesn't actually move any of the interesting entry points, so
any offending bootloader will still continue to "work" after this patch
is applied. For some version of "work" which includes jumping into the
compressed payload and crashing, if the bzImage it's given is a 32-bit
kernel. No change there then.
[ hpa: some of the issues in the description are addressed or
retconned by the 2.12 boot protocol. This patch has been edited to
only remove fixed addresses that were *not* thus retconned. ]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
The 'Attributes' argument to pci->Attributes() function is 64-bit. So
when invoking in 32-bit mode it takes two registers, not just one.
This fixes memory corruption when booting via the 32-bit EFI boot stub.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
If the bootloader calls the EFI handover entry point as a standard function
call, then it'll have a return address on the stack. We need to pop that
before calling efi_main(), or the arguments will all be out of position on
the stack.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
When booting under OVMF we have precisely one GOP device, and it
implements the ConOut protocol.
We break out of the loop when we look at it... and then promptly abort
because 'first_gop' never gets set. We should set first_gop *before*
breaking out of the loop. Yes, it doesn't really mean "first" any more,
but that doesn't matter. It's only a flag to indicate that a suitable
GOP was found.
In fact, we'd do just as well to initialise 'width' to zero in this
function, then just check *that* instead of first_gop. But I'll do the
minimal fix for now (and for stable@).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
