probe routine could index into port[] with -ve index. The check in
arc_uart_init_one() was too late.
This came to light when trying to port driver to CONFIG_OF, where
bydefault of-core code sets -ve platform dev id and in absence of
DT serial aliases, driver would use the -ve index.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA's Tegra has multiple UART controller which supports:
- APB DMA based controller fifo read/write.
- End Of Data interrupt in incoming data to know whether end
of frame achieve or not.
- HW controlled RTS and CTS flow control to reduce SW overhead.
Add serial driver to use all above feature.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silences the following checkpatch error:
ERROR: that open brace { should be on the previous line
Cc: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This eliminates having an #ifdef returning NULL for the case
when OF is disabled.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The address S3C_VA_UART is a statically ioremapped address. The driver
should not be using this. Instead, the driver should setup a mapping
during probe.
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detected by cppcheck:
[others/linux/drivers/tty/serial/mxs-auart.c:553]: (style) Same expression on both sides of '||'.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that support for RM9000 and platforms based on it has been removed,
remove the serial driver for it as well. It's really only been a quirk
for an almost 8250 compatible UART anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/tty/serial/8250/8250.c | 70 +----------------------------------------
drivers/tty/serial/8250/Kconfig | 9 ------
include/linux/serial_core.h | 1 -
3 files changed, 1 insertion(+), 79 deletions(-)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
before goto out5, soft, control, serial are all assigned to idd
after finish call ioc4_serial_remove_one, all resources are released
we need return instead of go on, or double free
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the call to gsm->output should be in the tx_lock,
that could avoid potential race from MUX level. But
we have no tx_lock in gsm_send.
This patch is to add tx_lock in gsm_send.
Signed-off-by: xiaojin <jin.xiao@intel.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CSR SiRFmarco's UART IP is same with SiRFprimaII except that
it has two more uart ports.
this patch makes the old driver support new SiRFmarco as well:
1. add .compatible = "sirf,marco-uart" to OF match table
2. add two ports in the port table
3. take spin_lock in isr to avoid the conflict of threads opening
uart on CPU1 and isr running on CPU0.
For 3, we did see some problems on SiRFmarco as SiRFmarco is a
SMP SoC but the old SiRFprimaII is UP.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty: vt/Makefile: set the variables to static
In the file drivers/tty/vt/defkeymap.c generated by command
loadkeys --mktable defkeymap.map > defkeymap.c
the 6 variables: shift_map, altgr_map, ctrl_map, shift_ctrl_map, alt_map,
and ctrl_alt_map should be static because they are used only in this file.
There is no reason to remove the static by sed command.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial core is using power states lifted from ACPI for no
good reason. Remove this reference from the documentation and
alter all users to use an enum specific to the serial core
instead, and define it in <linux/serial_core.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some systems require the additional communication functionality of a
9-bit UART. For that we could use the "stick" (mark/space) parity
bit supported on omap serial device. When is set, if PARODD is set the
parity bit is always 1; if PARODD is not set, then the parity bit is
always 0.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix call to line discipline receive_buf by synclink drivers.
Dummy flag buffer argument is ignored by N_HDLC line discipline but might
be of insufficient size if accessed by a different line discipline
selected by mistake. flag buffer allocation now matches max size of data
buffer. Unused char_buf buffers are removed.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Extended Management Interface (EMI) registers are accessed by first
writing the EMI register offset to the EMI_ADDR regiter and then either
reading or writing the data to/from the EMI_DATA register. Add helper
functions for performing these steps and convert existing EMI register
accesses accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jonathan Woithe posted an out of tree enabler/control module for these
cards. Lift the relevant identifiers and put them in the 8250_pci driver
along with code used to control custom registers on these cards.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1def9238d4 (net_sched: more precise pkt_len computation)
does a wrong computation of mac + network headers length, as it includes
the padding before the frame.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has
changed from previous ICH/PCH LOMs. When validating the EEPROM checksum,
check the appropriate bit on different devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As protocol driver, IFX SPI driver initiate to setup SPI master with default
SPI word size as 16 bit/word, however, SPI master may not adopt this default
value due to SPI controller's capability, it might choose an available value by
itself and set it to spi_device.bits_per_word. In order to keep align with
Controller, IFX driver should make use of this value during SPI transfer,
but the default one.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The setting of uart line control configuration in s3c24xx_serial_resetport
is can be removed since the 'set_termios' call will overwrite any ULCON
register setting which s3c24xx_serial_resetport does.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When data blocks are written to the EEPROM, the HW/SW/FW semaphore must be
held for the duration. With large data blocks on 80003es2lan, 82571 and
82572, this can take too long and cause the firmware to take ownership of
the semaphore and consequently ownership of writes to the EEPROM.
Instead, acquire and release the semaphore for each page of the block
written.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enables flow control to be set in SerDes autoneg mode. This is what is
done for copper, but relies on a different set of register/bit checks
since this is all done within the Mac registers.
Remove inapplicable comment in defines.h
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 41bd956de3.
The fix is incorrect and not appropiate for the latest kernels.
In fact it _causes_ the BUG: scheduling while atomic while
doing vCPU hotplug.
Suggested-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When shut down SPI port, it's possible that MRDY has been asserted and a SPI
timer was activated waiting for SRDY assert, in the case, it needs to delete
this timer.
Signed-off-by: Chen Jun <jun.d.chen@intel.com>
Signed-off-by: channing <chao.bi@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The correct device id for this card is 0x0022
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty/8250: pbn_b0_8_1152000_200 is supposed to be an 8 port definition
Signed-off-by: Matt Schulte <matts@commtech-fastcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, function of_clk_get() returns ERR_PTR()
and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following warning when building with W=1 option:
drivers/tty/serial/mxs-auart.c: In function 'mxs_auart_tx_chars':
drivers/tty/serial/mxs-auart.c:272:10: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the patch "serial: mxs-auart: fix the wrong RTS hardware flow control" the
mainline mxs-uart driver now sets RTSEN only when hardware flow control is
enabled via software. It is not possible any longer to set RTS manually via
software. However, the manual modification is a valid operation.
Regain the possibility to set RTS via software and only set RTSEN when hardware
flow control is explicitly enabled via settermios cflag CRTSCTS.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need for spinlocks in this file, then removing its header.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
This patch changes the function thermal_generate_netlink_event
to receive a thermal zone device instead of a originator id.
This way, the messages will always be bound to a thermal zone.
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Added shutdown callback to disable RX and TX when there is no other client
accesing the device.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thus, we don't enable RX when a termios setup has been called, as it could be
disabled previously.
As the control registers (Rx, Tx flags specifically) cannot be read from the
device, we keep this info in rx_enable.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function is already called in ipoctal_irq_rx()
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We protect important data such as TX buffer pointer, nb_bytes counter and status
registers of the device, from accessing several times at the same time.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the IRQ processing, we can generate another IRQ that can come before we
end the previous one, so we lost it. E.g. when transmitting a character.
To allow the processing in SMP machines, we ack the IRQ at the beginning of the
IRQ handler.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RX is enabled when the tty port is open, so no need to do it in initialization
time: it can allow the device to receive characters but no TTY client is
listening to them.
It produced an infinite number of IRQ as RxFIFO is not read to clear that
IRQ in the device, so it is still pending.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending of the device, it disables the TX mode in different places when there
is no more data to transmit.
This patch reorder them and disable the TX mode in the same place.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of several characters present in RxFIFO, they will have the flag of the
previous one, no matter if the actual character was received properly or not.
This patch fixes this bug.
Signed-off-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
