This patch re-enables Energy Detect Power Down (EDPD) mode for the
LAN8710/LAN8720. EDPD mode was disabled in a previous commit,
(b629820d18), because it was causing the
PHY to not be able to detect a link when cold started without a cable
connected.
The LAN8710/LAN8720 requires a minimum of 2 link pulses within 64ms of
each other in order to set the ENERGYON bit and exit EDPD mode. If a
link partner does send the pulses within this interval, the PHY will
remained powered down.
This workaround will manually toggle the PHY on/off upon calls to
read_status in order to generate link test pulses if the link is down.
If a link partner is present, it will respond to the pulses, which will
cause the ENERGYON bit to be set and will cause the EDPD mode to be
exited.
Signed-off-by: Patrick Trantham <patrick.trantham@fuel7.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if a socket was repaired with a few packet in a write queue,
a kernel bug may be triggered:
kernel BUG at net/ipv4/tcp_output.c:2330!
RIP: 0010:[<ffffffff8155784f>] tcp_retransmit_skb+0x5ff/0x610
According to the initial realization v3.4-rc2-963-gc0e88ff,
all skb-s should look like already posted. This patch fixes code
according with this sentence.
Here are three points, which were not done in the initial patch:
1. A tcp send head should not be changed
2. Initialize TSO state of a skb
3. Reset the retransmission time
This patch moves logic from tcp_sendmsg to tcp_write_xmit. A packet
passes the ussual way, but isn't sent to network. This patch solves
all described problems and handles tcp_sendpages.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the offload callbacks into its own structure.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sing GSO support is now separate, pull it out of the module
and make it its own init call.
Remove the cleanup functions as they are no longer called.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since GSO/GRO support is now separated, make IPv4 GSO a
stand-alone init call and not part of inet_init().
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP offload needs some additional functions to be in the static kernel
for it work correclty. Move those functions into the core.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the exthdr offload functionality into a separeate
file in preparate for moving it out of the module
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull UDP GSO code into a separate file in preparation for moving
the code out of the module.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull TCPv6 offload functionality into its won file in preparation
for moving it out of the module.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate IPv6 offload functionality into its own file
in preparation for the move out of the module
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch IPv6 protocol to using the new GRO/GSO calls and data.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch IPv4 code base to using the new GRO/GSO calls and data.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new data structure for IPv6 protocols that holds GRO/GSO
callbacks and a new array to track the protocols that register GRO/GSO.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new data structure for IPv4 protocols that holds GRO/GSO
callbacks and a new array to track the protocols that register GRO/GSO.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to using the new GSO/GRO registration mechanism and new
packet offload structure.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new data structure to contain the GRO/GSO callbacks and add
a new registration mechanism.
Singed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New options enabled:
* BRCMFMAC: wlan driver, enable as module.
* MTD, MTD_CHAR, MTD_M25P80, SPI_TEGRA20_SLINK, CONFIG_SPI_TEGRA20_SFLASH
to enable serial flash on Cardhu and TrimSlice.
* PWM/backlight features for use with tegradrm.
* tegradrm; Tegra's new display driver.
* CMA, so that tegradrm can allocate large buffers.
* SquashFS, which is used as the root filesystem on boards based on
the Tamonten processor module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Trace buffer size is now per-cpu, so that there are the following two
patterns in resizing of buffers.
(1) resize per-cpu buffers to same given size
(2) resize per-cpu buffers to another trace_array's buffer size
for each CPU (such as preparing the max_tr which is equivalent
to the global_trace's size)
__tracing_resize_ring_buffer() can be used for (1), and had
implemented (2) inside it for resetting the global_trace to the
original size.
(2) was also implemented in another place. So this patch assembles
them in a new function - resize_buffer_duplicate_size().
Link: http://lkml.kernel.org/r/20121017025616.2627.91226.stgit@falsita
Signed-off-by: Hiraku Toyooka <hiraku.toyooka.gu@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The L2 RAM is in different power domain from the CPU cluster. So the
L2 content can be retained over CPU suspend/resume. To do that, we
need to disable L2 after the MMU is disabled, and enable L2 before
the MMU is enabled. But the L2 controller is in the same power domain
with the CPU cluster. We need to restore it's settings and re-enable
it after the power be resumed.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is a power gating idle mode. It support power gating vdd_cpu rail
after all cpu cores in "powered-down" status. For Tegra30, the CPU0 can
enter this state only when all secondary CPU is offline. We need to take
care and make sure whole secondary CPUs were offline and checking the
CPU power gate status. After that, the CPU0 can go into "powered-down"
state safely. Then shut off the CPU rail.
Be aware of that, you may see the legacy power state "LP2" in the code
which is exactly the same meaning of "CPU power down".
Base on the work by:
Scott Williams <scwilliams@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The flow controller can help CPU to go into suspend mode (powered-down
state). When CPU go into powered-down state, it needs some careful
settings before getting into and after leaving. The enter and exit
functions do that by configuring appropriate mode for flow controller.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add suspend, resume and rail_off_ready API into tegra_cpu_car_ops. These
functions were used for CPU powered-down state maintenance. One thing
needs to notice the rail_off_ready API only availalbe for cpu_g cluster
not cpu_lp cluster.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable csite (debug and trace controller) clock at init to prevent it
be disabled. And this also the necessary clock for CPU be brought up or
resumed from a power-gating low power state.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This supports power-gated idle on secondary CPUs for Tegra30. The
secondary CPUs can go into powered-down state independently. When
CPU goes into this state, it saves it's contexts and puts itself
to flow controlled WFI state. After that, it will been power gated.
Be aware of that, you may see the legacy power state "LP2" in the
code which is exactly the same meaning of "CPU power down".
Based on the work by:
Scott Williams <scwilliams@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The CPU suspending on Tegra means CPU power gating. We add a resume
function for taking care the CPUs that resume from power gating status.
This function was been hooked to the reset handler. We take care
everything here before go into kernel.
Be aware of that, you may see the legacy power status "LP2" in the code
which is exactly the same meaning of "CPU power down".
Based on the work by:
Scott Williams <scwilliams@nvidia.com>
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The different Tegra chips may have different CPU idle states and data.
Individual CPU idle driver make it more easy to maintain.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
For the naming consistency under the mach-tegra, we re-name the file of
"sleep-tXX" to "sleep-tegraXX" (e.g., sleep-t30 to sleep-tegra30).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra CPU idle LP3 state is doing ARM WFI only. So it's same with
the common ARM_CPUIDLE_WFI_STATE. Using it to replace LP3 now.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the host1x node along with its children to the Tegra30 DTSI. Board-
specific DTS files are expected to enable the available outputs and
complement the device tree with data specific to the hardware.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the host1x node along with its children to the Tegra20 DTSI. Board-
specific DTS files are expected to enable the available outputs and
complement the device tree with data specific to the hardware.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Nvidia's Tegra20 have the SPI (SFLASH) controller to
interface with spi flash device which is used for system
boot. Add DT entry for this controller.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: move sflash node to keep file sorted]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Harmony board has an ON Semiconductors NCT1008 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tamonten SOM has an ON Semiconductor NCT1008 connected to the DVC
bus which is used to measure the ambient (local) temperature as well as
the on-die (remote) temperature.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Harmony board has an Analog Devices ADT7461 temperature sensor
connected to the DVC bus. It can be used to monitor the ambient (local)
and on-die (remote) temperatures.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
These properties are already set by the tegra20-tamonten.dtsi, so they
don't need to be repeated.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This commit allows the I2C2 controller on Tegra20 to be routed either to
the DDC or the PTA pin group at runtime. On Tamonten this allows the I2C
bus to be used for the DDC of the HDMI connector or to access I2C chips
on the carrier board.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable SLINK4 and connected device in Tegra30 based
platform Cardhu.
Setting maximum spi frequency to 25MHz.
SPI serial flash is connected on CS1 of SLINK4 on
cardhu platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[swarren: swapped reg/compatible order to be consistent]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add slink controller details in the dts file of
Tegra20 and Tegra30.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra 2's I2C2 controller can be routed to either the PTA
or DDC pin group on Ventana. So:
- Remove the HDMI function definition of pta pingroup
- Define child i2c adapters(ddc & pta) for I2C2 controller
Signed-off-by: Mark Zhang <markz@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Configure pinmux as required for WiFi.
Enable the SDHCI1 controller for a02 and a04 board, which is connected to the
WiFi module.
For now, always enable the regulator that provides power to the Wifi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Configure pinmux as required for WiFi.
Enable the SDHCI1 controller, which is connectted to the WiFi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable the SDHCI1 controller. This is connected to the WiFi module.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Setup the clock parents for the two display controllers and HDMI.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the OF_DEV_AUXDATA table entries required to associate the proper
names with host1x and its children. In turn, this allows the devices to
find the required clocks.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Extend the pll_d frequency table with a few entries to support common
HDMI and LVDS display modes and setup the clock parents for the two
display controllers and HDMI.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the OF_DEV_AUXDATA table entries required to associate the proper
names with host1x and its children. In turn, this allows the devices to
find the required clocks.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The LOCKSTATUS register for memory-mapped coresight devices indicates
whether or not the device in question implements hardware locking. If
not, locking is not present (i.e. LSR.SLI == 0) and LAR is write-ignore,
so software doesn't actually need to check the status register at all.
This patch removes the broken LSR checks.
Cc: Ming Lei <ming.lei@canonical.com>
Reported-by: Mike Williams <michael.williams@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds speedo-based process identification support for Tegra30.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
[swarren s/Tegra3/Tegra30/ in log print,
s/T30/Tegra30/ in commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Detect CPU and core process ID by checking speedo corner tables.
This can provide a more accurate process ID.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
[swarren s/Tegra2/Tegra20/ in log print]
Signed-off-by: Stephen Warren <swarren@nvidia.com>