The physical base address of GIC and Interrupt Combiner is obtained from
device tree and then remapped during initialization. So remove the
static io-remapping for GIC and combiner.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Split the omap4_hdmi_mux_pads() function into two parts, one handles the
tpd12s015 gpio muxing, the other handles the hdmi pins.
This is clearer, as hdmi and tpd12s015 are separate devices, and it also
allows us to mux those separately with DT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The dispc error handler tries to "fix" issues by disabling and enabling
panel. This is problematic, as we're trying to remove the dependency
from omapdss to the omap_dss_devices. It's also racy, and doesn't really
fix anything.
This patch removes the use of omap_dss_device from the error handler,
and just disables and enables the associated overlay manager. This
should produce similar results as the previous solution, without using
dssdev.
However, the error handling is still horrible. But the problem boils
down to one question, to which I don't have a clear answer: what to do
when a HW error happens?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dispc's error handler has a loop inside another loop, and both use
the same loop variable. This is clearly wrong, and this patch makes a
new variable for the inner loop.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current omapfb code goes over all the modes found from the monitors
EDID data, and searches for a mode that is compatible with the DSS
hardware and has the highest x-res.
While this works ok as such, it proves problematic when using DSI PLL
for pixel clock. Calculating DSI PLL dividers is not the fastest of the
operations, and while doing it for one mode is usually ok, doing it for
20 modes is noticable.
Also, the first mode given in the EDID data should be the native mode of
the monitor, and thus also the best mode, so if that can be used, no
need to look further.
This patch changes the code to use the first mode that is compatible
with the DSS hardware.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It seems that using the second EDID block causes more problems than is
of any help. The first mode in the extended block will get
FB_MODE_IS_FIRST set, which will override the first mode from the first
EDID block, thus making the default videomode selection not to work
properly.
This patch removes the use of the extended edid block for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi driver tries to find the given video timings from its static
list of timings, to find the required ID for the mode. The check tries
to find exact match for the pixel clock, among other checks.
with omapfb driver there can be some amount of error in the give pixel
clock, as the pixel clock is converted between Hz and ps, thus the
hdmi's check fails to find the mode.
This patch makes the check more allowing, by rounding the pixel clocks
to nearest MHz.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
This patch makes use of the hdmi_power_[on|off]_core() functions added
in the previous patch. The functions are used when reading EDID or
detecting if a monitor is connected.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
There's currently just one power-on function for HDMI, which enables the
IP and the video output. When reading EDID or detecting if a monitor is
connected, we don't need the video output.
Enabling the video output for these operations is not a big problem in
itself, but the quick enable/disable cycles caused by the operations
seem to cause sync lost errors from time to time. Also, this makes it
possible to read the EDID before the full video path has been set up.
This patch splits the hdmi_power_on into two parts, hdmi_power_on_core
and hdmi_power_on_full. The "full" version does what hdmi_power_on does
currently, and hdmi_power_on_core only enables the core IP. Similar
changes are made for power_off.
Note that these don't allow the HDMI IP to be first enabled, and later
enable the video output, but the HDMI IP will first need to be powered
off before calling the full version. So this is rather limited
implementation, but it fills the needs for reading EDID.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
DISPC irqs need to be handled from the compat layer and also in the
future by the omapdrm. To make this possible, this patchs adds a set of
helper functions, so that the irqs can be managed without direct
register reads/writes.
The following functions are added, and all the current direct reg
reads/writes are changed to use these.
u32 dispc_read_irqstatus(void);
void dispc_clear_irqstatus(u32 mask);
u32 dispc_read_irqenable(void);
void dispc_write_irqenable(u32 mask);
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new dispc function, dispc_ovl_enabled(). This returns if the overlay
enable bit is set in the registers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need a low level manager-enable function for omapdrm. We have that
function as dispc internal func, _enable_mgr_out().
This patch exposes that function, and renames it to dispc_mgr_enable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current dispc_mgr_enable/disable function are blocking, and do a bit
too much for omapdrm. We'll expose new enable & disable functions that
will just set the bits in the registers in the following patches.
This patch renames the current functions to *_sync, to make it clear
that they are blocking, and also to free up the dispc_mgr_enable/disable
names for these new functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use dss_feat_get_num_ovls() in dispc.c instead of
omap_dss_get_num_overlays() to remove the dependency to overlay.c. Note
that we still have uses of omap_dss_get_num_overlays() in dispc.c, but
these will be moved out in the future patches.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently omapdss driver sets up the initial connections between
overlays, overlay manager and a panel, based on default display
parameter coming from the board file or via module parameters.
This is unnecessary, as it's the higher level component that should
decide what display to use and how. This patch removes the code from
omapdss, and implements similar code to omapfb.
The def_disp module parameter and the default display platform_data
parameter are kept in omapdss, but omapdss doesn't do anything with
them. It will just return the default display name with
dss_get_default_display_name() call, which omapfb uses. This is done to
keep the backward compatibility.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Export dss_get_def_display_name() with the name of
omapdss_get_def_display_name() so that omapfb can use it after the next
patch which moves default display handling to omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clarify the documentation to indicate that these
flags can only be used at the end, i.e. after them
a copy TFD (no flags set) is invalid.
Reported-by: Inbal Hacohen <inbal.hacohen@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In addition to the NOCOPY flag, add a DUP flag that
tells the transport to kmemdup() the buffer and free
it after the command completes.
Currently this is only supported for a single buffer
in a given command, but that could be extended if it
should be needed.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This board supports:
- AM1808 based board
- 64 MiB DDR ram
- 2 MiB Nor flash
- 128 MiB NAND flash
- use internal RTC
- I2C support
- hwmon lm75 support
- UBI/UBIFS support
- MMC support
- USB OTG support
This patch adds the basic DTS file enabling the serial ports.
Other features will be added in due course of time.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: davinci-linux-open-source@linux.davincidsp.com
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
[nsekhar@ti.com: modified after dtsi refactoring and added binding
documentation]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add DT data for DA850 SoC. Only interrupt controller and
serial port information is being added at this time.
Signed-off-by: Heiko Schocher <hs@denx.de>
[nsekhar@ti.com: refactored DT data into SoC specific and
board specific and include SoC data into .dtsi file]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Using the 'o' memory constraint in inline assembly can result in GCC
generating invalid immediate offsets for memory access instructions with
reduced addressing capabilities (i.e. smaller than 12-bit immediate
offsets):
http://gcc.gnu.org/bugzilla/show_bug.cgi?id=54983
As there is no constraint to specify the exact addressing mode we need,
fallback to using 'Q' exclusively for halfword I/O accesses. This may
emit an additional add instruction (using an extra register) in order
to construct the address but it will always be accepted by GAS.
Reported-by: Bastian Hecht <hechtb@googlemail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/media/tuners/xc4000.c: In function ‘check_firmware’:
drivers/media/tuners/xc4000.c:1048:45: warning: ‘fw_minor’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1048:39: warning: ‘fw_major’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1062:39: warning: ‘hw_minor’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1062:33: warning: ‘hw_major’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While it is very unlikely, if the number of parameters for
QAMDemodulatorCommand is not 2 or 4, status become undefined:
/home/hans/work/build/v4l-dvb-git/drivers/media/dvb-frontends/drxk_hard.c: In function ‘QAMDemodulatorCommand’:
/home/hans/work/build/v4l-dvb-git/drivers/media/dvb-frontends/drxk_hard.c:5452:5: warning: ‘status’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After commit 846a136881 ("ARM: vfp: fix
saving d16-d31 vfp registers on v6+ kernels"), the OMAP 2430SDP board
started crashing during boot with omap2plus_defconfig:
[ 3.875122] mmcblk0: mmc0:e624 SD04G 3.69 GiB
[ 3.915954] mmcblk0: p1
[ 4.086639] Internal error: Oops - undefined instruction: 0 [#1] SMP ARM
[ 4.093719] Modules linked in:
[ 4.096954] CPU: 0 Not tainted (3.6.0-02232-g759e00b #570)
[ 4.103149] PC is at vfp_reload_hw+0x1c/0x44
[ 4.107666] LR is at __und_usr_fault_32+0x0/0x8
It turns out that the context save/restore fix unmasked a latent bug
in commit 5aaf254409 ("ARM: 6203/1: Make
VFPv3 usable on ARMv6"). When CONFIG_VFPv3 is set, but the kernel is
booted on a pre-VFPv3 core, the code attempts to save and restore the
d16-d31 VFP registers. These are only present on non-D16 VFPv3+, so
this results in an undefined instruction exception. The code didn't
crash before commit 846a136 because the save and restore code was
only touching d0-d15, present on all VFP.
Fix by implementing a request from Russell King to add a new HWCAP
flag that affirmatively indicates the presence of the d16-d31
registers:
http://marc.info/?l=linux-arm-kernel&m=135013547905283&w=2
and some feedback from Måns to clarify the name of the HWCAP flag.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@linaro.org>
Cc: Måns Rullgård <mans.rullgard@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The scheduler imposes a requirement to sched_clock()
which is to stop the clock during suspend, if we don't
do that any RT thread will be rescheduled in the future
which might cause any sort of problems.
This became an issue on OMAP when we converted omap-i2c.c
to use threaded IRQs, it turned out that depending on how
much time we spent on suspend, the I2C IRQ thread would
end up being rescheduled so far in the future that I2C
transfers would timeout and, because omap_hsmmc depends
on an I2C-connected device to detect if an MMC card is
inserted in the slot, our rootfs would just vanish.
arch/arm/kernel/sched_clock.c already had an optional
implementation (sched_clock_needs_suspend()) which would
handle scheduler's requirement properly, what this patch
does is simply to make that implementation non-optional.
Note that this has the side-effect that printk timings
won't reflect the actual time spent on suspend so other
methods to measure that will have to be used.
This has been tested with beagleboard XM (OMAP3630) and
pandaboard rev A3 (OMAP4430). Suspend to RAM is now working
after this patch.
Thanks to Kevin Hilman for helping out with debugging.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for booting DA850 using flattened device
tree to describe the hardware. At this time only the
very basic bootup using a serial console is supported.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Registers the uio_pruss platform device on the DA850 EVM.
Tested on AM180x-EVM using the PRU_memAccessPRUDataRam and
PRU_memAccessL3andDDR examples from the PRU userspace tools
available from http://www.ti.com/tool/sprc940
Signed-off-by: Matt Porter <mporter@ti.com>
[nsekhar@ti.com: use pr_warn() instead of pr_warning()]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
in case of client roaming a new global entry is added while a corresponding
local one is still present. In this case the node can safely pass the WIFI flag
from the local to the global entry.
This change is required to let the AP-isolation correctly working in case of
roaming: if a generic WIFI client C roams from node A to B, A adds a global
entry for C without adding any WIFI flag. The latter will be set only later,
once A has received C's advertisement from B. In this time period the
AP-Isolation (if enabled) would not correctly work since C is not marked as
WIFI, so allowing it to communicate with other WIFI clients.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In order to properly convert a bitwise AND to a boolean value, the whole
expression must be prepended by "!!".
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
In batadv_check_unicast_ttvn() the code accesses both the unicast header and the
Ethernet header in the payload. For this reason pskb_may_pull() must be invoked
to check for the required space.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To simplify TranslationTable debugging it is better to print the packet
rerouting message on the DBG_TT log level. In this way a developer interested in
packets rerouting doesn't need to filter it out of the whole ROUTES log.
Moreover, since this message will appear for each rerouted message, it is now
"ratelimited".
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
in case of a new global entry added because of roaming, the roam_at field must
be properly initiated with the current time. This value will be later use to
purge this entry out on time out (if nobody claims it). Instead roam_at field
is now set to zero in this situation leading to an immediate purging of the
related entry.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
We have seen this to break networks when used with bridge loop
avoidance. As we can't see any benefit from sending these ancient frames
via our mesh, we just drop them.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
The test whether we can use a router for alternating bonding should only be
done once because it is already known that it is still usable and will not be
deleted from the list soon.
This patch addresses Coverity #712285: Unchecked return value
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
New operations should not be started when they need an increased module
reference counter and try_module_get failed.
This patch addresses Coverity #712284: Unchecked return value
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
batadv_bit_get_packet checks for all common situations before it decides that
the new received packet indicates that the host was restarted. This extra
condition check at the end of the function is not necessary because this
condition is always true.
This patch addresses Coverity #712296: Logically dead code
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Transmissions over batman-adv devices always start another nested transmission
over devices attached to the batman-adv interface. These devices usually use
the ethernet lockdep class for the tx_queue lock which is also set by default
for all batman-adv devices. Lockdep will detect a nested locking attempt of two
locks with the same class and warn about a possible deadlock.
This is the default and expected behavior and should not alarm the locking
correctness prove mechanism. Therefore, the locks for all netdevice specific tx
queues get a special batman-adv lock class to avoid a false positive for each
transmission.
Reported-by: Linus Luessing <linus.luessing@web.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
To avoid code duplication and to simplify further changes,
check_unicast_packet() is now used in recv_roam_adv() to check for not
well formed packets and so discard them.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Shifting them up into the vmalloc region prevents the following warning,
when booting a zynq qemu target with more than 512mb of RAM:
BUG: mapping for 0xe0000000 at 0xe0000000 out of vmalloc space
In addition, it allows for reuse of these mappings when the proper
drivers issue requests via ioremap().
There are currently unknown issues with the early uart mapping. For
now, the uart will be mapped to a known working address.
Signed-off-by: Josh Cartwright <josh.cartwright@ni.com>
Cc: John Linn <john.linn@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Michal Simek <michal.simek@xilinx.com>