Add device_type for memory node to fix below CHECK_DTB warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-b105pv2.dtb: / (ge,imx6dl-b105pv2): memory@10000000: 'device_type' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bus type for parallel ov5640 to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-sabrelite.dtb: camera@42 (ovti,ov5642): port:endpoint:hsync-active: False schema does not allow 1
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add supplies for wm8731 to fix below CHECK_DTB warnings:
arch/arm/boot/dts/nxp/imx/imx6q-cm-fx6.dtb: codec@1a (wlf,wm8731): 'AVDD-supply' is a required property
from schema $id: http://devicetree.org/schemas/sound/wlf,wm8731.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix typo interrupt, which should be 'interrupts'. Fix below CHECK_DTBS
warnings.
arch/arm/boot/dts/nxp/imx/imx6dl-skov-revc-lt2.dtb: switch@0 (microchip,ksz8873): Unevaluated properties are not allowed ('interrupt', 'pinctrl-names' were unexpected)
from schema $id: http://devicetree.org/schemas/net/dsa/microchip,ksz.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove redundant linux,phandle to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-gw560x.dtb: pmic@3c (lltc,ltc3676): regulators:sw3: Unevaluated properties are not allowed ('linux,phandle' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename power-supply to vcc-supply for touchscreen to fix below CHECK_DTB
warnings:
arch/arm/boot/dts/nxp/imx/imx6ull-dhcom-pdk2.dtb: touchscreen@38 (edt,edt-ft5406): Unevaluated properties are not allowed ('power-supply' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add power-supply for lcd panel to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-evi.dtb: panel (sharp,lq101k1ly04): 'power-supply' is a required property
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The same displays that can be connected directly to the
imx8mp-phyboard-pollux can also be connected to the expansion board
PEB-AV-10. For displays connected to the expansion board, a second LVDS
channel of the i.MX 8M Plus SoC is used and only a single display
connected to the SoC LVDS display bridge at a given time is supported.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
An expansion board (PEB-AV-10) may be connected to the
imx8mp-phyboard-pollux. Its main purpose is to provide multimedia
interfaces, featuring a 3.5mm headphone jack, a USB-A port and LVDS as
well as backlight connectors.
Introduce the expansion board as dtsi, as it may be used standalone as
an expansion board, as well as in combination with display panels. These
display panels will include the dtsi.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mp-phyboard-pollux had a display baked into its board dts file.
However this approach does not truly discribe the hardware and is not
suitable when using different displays.
Move display specific description into an overlay and add the successor
display for the phyboard-pollux as an additional overlay.
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change license from GPL-2.0 to GPL-2.0-or-later OR MIT.
Use syntax as defined in the SPDX standard. Also remove individual
authorship.
Acked-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We need the fixes in here, and it resolves a merge conflict in:
drivers/misc/amd-sbi/Kconfig
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The msi-map property was incorrectly applied to pcie0-ep instead of
pcie1-ep. Correct the msi-map for both pcie0-ep and pcie1-ep nodes.
Fixes: bbe4b2f7d6 ("arm64: dts: imx95: Add msi-map for pci-ep device")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In normal case, there is no need to invoke mutex_destroy in error path,
but it is useful when CONFIG_DEBUG_MUTEXES, so use devm_mutex_init().
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SCU driver is critical for system working properly, it should
never be removed and binded again. So suppress the bind attrs
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX_SC_ERR_NOTFOUND should map with -ENOENT, not -EEXIST. -ENODEV makes
more sense for IMX_SC_ERR_NOPOWER, and -ECOMM makes more sense for
IMX_SC_ERR_IPC.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since its introduction, this symbol has not been used by any loadable
modules. It remains only referenced within imx-scu.c, which is always built
together with imx-scu-irq.c
As such, exporting imx_scu_enable_general_irq_channel is unnecessary, so
remove the export.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
mu_resource_id is referenced in imx_scu_irq_get_status() and
imx_scu_irq_group_enable() which could be used by other modules, so
need to set correct value before using imx_sc_irq_ipc_handle in
SCU API call.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With mailbox channel requested, there is possibility that interrupts may
come in, so need to make sure the workqueue is initialized before
the queue is scheduled by mailbox rx callback.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IRQ mailbox is an optional channel and does not need to be kept until
driver removal when an error occurs. Free the allocated memory in the
error path.
Add 'goto free_cl' when mbox_request_channel_byname() fails, to keep free
at one place.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx_scu_enable_general_irq_channel() calls of_parse_phandle_with_args(),
but does not release the OF node reference. Add a of_node_put() call
to release the reference.
Fixes: 851826c756 ("firmware: imx: enable imx scu general irq function")
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename i2c<n>mux to i2c to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-nitrogen6_max.dtb: i2c2mux (i2c-mux-gpio): $nodename:0: 'i2c2mux' does not match '^(i2c-?)?mux'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove extra space in " jedec,spi-nor" to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6ull-phytec-tauri-emmc.dtb: /soc/bus@2000000/spba-bus@2000000/spi@2008000/flash@2: failed to match any schema with compatible: [' jedec,spi-nor']
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device_type, bus-range, ranges for pci nodes. Rename intel,i211 to
ethernet to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-utilite-pro.dtb: pcie@0,0: 'device_type' is a required property
from schema $id: http://devicetree.org/schemas/pci/pci-bus-common.yaml#
arch/arm/boot/dts/nxp/imx/imx6q-utilite-pro.dtb: pcie@0,0: 'ranges' is a required property
from schema $id: http://devicetree.org/schemas/pci/pci-bus-common.yaml
arm/boot/dts/nxp/imx/imx6q-utilite-pro.dtb: pcie@0,0: 'intel,i211@pcie0,0' does not match any of the regexes: '.*-names$', '.*-supply$', '^#.*-cells$', '^#[a-zA-Z0-9,+\\-._]{0,63}$', '^[a-zA-Z0-9][a-zA-Z0-9#,+\\-._]{0,63}$', '^[a-zA-Z0-9][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$', '^__.*__$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/dt-core.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename ir_recv to ir-receiver to fix below CHECK_DTBS warnings:
arm/boot/dts/nxp/imx/imx6q-tbs2910.dtb: ir_recv (gpio-ir-receiver): $nodename:0: 'ir_recv' does not match '^ir(-receiver)?(@[a-f0-9]+)?$'
from schema $id: http://devicetree.org/schemas/media/gpio-ir-receiver.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove redundant pinctrl-name since pinctrl-0 doesn't exist to fix below
CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-pistachio.dtb: pinctrl@20e0000 (fsl,imx6q-iomuxc): 'pinctrl-0' is a dependency of 'pinctrl-names'
from schema $id: http://devicetree.org/schemas/pinctrl/pinctrl-consumer.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Change voltage-divider's io-channel-cells to 1 to fix below CHECK_DTBS
warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-plym2m.dtb: voltage-divider-vaccu (voltage-divider): #io-channel-cells: 1 was expected
from schema $id: http://devicetree.org/schemas/iio/afe/voltage-divider.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove gpio suffix for regulator to fix below CHECK_DTBS warnings:
(fsl,imx6sx-sdb): regulator-pcie-gpio: {'compatible': ['regulator-fixed'], 'phandle': 69} is not of type 'array'
from schema $id: http://devicetree.org/schemas/gpio/gpio-consumer.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename ngpio to ngpios to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-ts4900.dtb: gpio@28 (technologic,ts4900-gpio): 'ngpio' does not match any of the regexes: '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', '^pinctrl-[0-9]+$'
from schema $id: http://devicetree.org/schemas/trivial-gpio.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
rename m95m02 to eeprom to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6q-evi.dtb: m95m02@1 (st,m95m02): $nodename: 'anyOf' conditional failed, one must be fixed:
'm95m02@1' does not match '^eeprom@[0-9a-f]{1,2}$'
'm95m02@1' does not match '^fram@[0-9a-f]{1,2}$'
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename touch-thermal0 to touch-0-thermal to fix below CHECK_DTBS warnings:
arch/arm/boot/dts/nxp/imx/imx6dl-plym2m.dtb: thermal-zones: 'touch-thermal0', 'touch-thermal1' do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,10}-thermal$', 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/thermal/thermal-zones.yaml
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename stmpgpio to gpio and add gpio-controller and interrupt-controller.
Rename stmpe_adc to adc. Move interrupt-controller and gpio-controller
under gpio node.
to fix below CHECK_DTBS warnings:
/home/lizhi/source/linux-upstream-pci/arch/arm/boot/dts/nxp/imx/imx6q-dmo-edmqmx6.dtb: stmpe1601@40 (st,stmpe1601): gpio: 'interrupt-controller' is a required property
from schema $id: http://devicetree.org/schemas/mfd/st,stmpe.yaml#
/home/lizhi/source/linux-upstream-pci/arch/arm/boot/dts/nxp/imx/imx6q-dmo-edmqmx6.dtb: gpio (st,stmpe-gpio): 'interrupt-controller' is a required property
from schema $id: http://devicetree.org/schemas/gpio/st,stmpe-gpio.yaml#
/home/lizhi/source/linux-upstream-pci/arch/arm/boot/dts/nxp/imx/imx6q-dmo-edmqmx6.dtb: stmpe1601@44 (st,stmpe1601): gpio: 'interrupt-controller' is a required property
from schema $id: http://devicetree.org/schemas/mfd/st,stmpe.yaml#
/home/lizhi/source/linux-upstream-pci/arch/arm/boot/dts/nxp/imx/imx6q-dmo-edmqmx6.dtb: gpio (st,stmpe-gpio): 'interrupt-controller' is a required property
from schema $id: http://devicetree.org/schemas/gpio/st,stmpe-gpio.yaml#
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the two SFP+ cages present on the LS1046AQDS board and their
associated I2C buses and GPIO lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the two SFP+ cages found on the LX2160ARDB board with their
respective I2C buses and GPIO lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The QIXIS FPGA node is extended so that it describes the GPIO controller
responsible for all the status presence lines on both SFP+ cages as well
as the IO SLOTs present on the board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the FPGA present on the LX2160ARDB board as a simple-mfd I2C
device. The FPGA presents registers that deal with power-on-reset
timing, muxing, SFP cage monitoring and control etc.
Also add the two GPIO controllers responsible for monitoring and
controlling the SFP+ cages used for MAC5 and MAC6.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Extend the list of accepted child nodes with the QIXIS FPGA based GPIO
controller and explicitly list its compatible string
fsl,ls1046aqds-fpga-gpio-stat-pres2 as the only one accepted.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Extend the list of supported compatible strings with fsl,lx2160ardb-fpga.
Since the register map exposed by the LX2160ARDB's FPGA also contains
two GPIO controllers, accept the necessary GPIO pattern property.
At the same time, add the #address-cells and #size-cells properties as
valid ones so that the child nodes of the fsl,lx2160ardb-fpga node are
addressable.
This is necessary because when defining child devices such as the GPIO
controller described in the added example, the child device needs a the
reg property to properly identify its register location in the parent
I2C device address space.
Impose this restriction for the new compatible through an if-statement.
The feature set exposed by these QIXIS FPGA devices is highly dependent
on the board type, meaning that even though the FPGA found on the
LX2160AQDS board (fsl,lx2160aqds-fpga) works in the same way in terms of
access over I2C as the one found on the LX2160ARDB (fsl,lx2160ardb-fpga
added here), the register map inside the device space is different since
there are different on-board devices to be controlled.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree for the Protonic PRT8ML.
The board is similar to the Protonic PRT8MM but i.MX8MP based.
Some features have been removed as the drivers haven't been mainlined
yet or other issues where encountered:
- Stepper motors to be controlled using motion control subsystem
- MIPI/DSI to eDP USB alt-mode
- Onboard T1 ethernet (10BASE-T1L+PoDL, 100BASE-T1+PoDL, 1000BASE-T1)
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The gpio0_mipi_csi DT nodes are enabled by default, but they are
dependent on the irqsteer_csi nodes, which are not enabled. This causes
the gpio0_mipi_csi GPIOs to be probe deferred. Since these GPIOs can be
used independently of the CSI controller, enable irqsteer_csi by default
too to prevent them from being deferred and to ensure they work out of
the box.
Fixes: 2217f82437 ("arm64: dts: imx8: add capture controller for i.MX8's img subsystem")
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Idle-inject up to 50% of all cpu's time in order to help cpufreq
to keep the temperature below the trip points.
Signed-off-by: Martin Kepplinger-Novaković <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The thermal framework can use the cpu-idle-states as
described for imx8mp as an alternative or in parallel to
cpufreq.
Add the DT node to the cpu so the cooling devices will be present
and the thermal zone descriptions can use them.
Signed-off-by: Martin Kepplinger-Novaković <martink@posteo.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In former times, ext4 was enabled implicitely by enabling ext3 but with
the ext3 fs gone, it does not get enabled, which lets devices fail to
mount root on non-initrd based boots with an ext4 root.
Fixes: d6ace46c82 ("ext4: remove obsolete EXT3 config options")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RTC inside mc34708 is supported by RTC_DRV_MC13XXX since v3.6-rc1.
Enable the PMIC RTC on the imx53-qsrb. Without a battery the RTC may be
powered via the micro-USB connector when main 5V power is not available.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Improve the performance of aes_gcm_aad_update_vaes_avx512() on large AAD
(additional authenticated data) lengths by 4-8 times by making it use up
to 512-bit vectors and a 4-vector-wide loop. Previously, it used only
256-bit vectors and a 1-vector-wide loop.
Originally, I assumed that the case of large AADLEN was unimportant.
Later, when reviewing the users of BoringSSL's AES-GCM code, I found
that some callers use BoringSSL's AES-GCM API to just compute GMAC,
authenticating lots of data but not en/decrypting any. Thus, I included
a similar optimization in the BoringSSL port of this code. I believe
it's wise to include this optimization in the kernel port too for
similar reasons, and to align it more closely with the BoringSSL port.
Another reason this function originally used 256-bit vectors was so that
separate *_avx10_256 and *_avx10_512 versions of it wouldn't be needed.
However, that's no longer applicable.
To avoid a slight performance regression in the common case of AADLEN <=
16, also add a fast path for that case which uses 128-bit vectors. In
fact, this case actually gets slightly faster too, since it saves a
couple instructions over the original 256-bit code.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20251002023117.37504-9-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Squaring in GF(2^128) requires fewer instructions than a generic
multiplication in GF(2^128). Take advantage of this when computing H^2
from H^1 in aes_gcm_precompute_vaes_avx512().
Note that aes_gcm_precompute_vaes_avx2() already uses this optimization.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20251002023117.37504-8-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
- Fix some references to field names in struct aes_gcm_key_vaes_avx512.
- Remove the mention of the counter having to start at 2. The assembly
code doesn't actually assume that it does.
Note that these changes improve consistency with aes-gcm-vaes-avx2.S.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20251002023117.37504-7-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>
Now that the _aes_gcm_precompute macro is instantiated only once,
replace it directly with a function definition.
Also, move aes_gcm_aad_update_vaes_avx512() to a different location in
the file so that it's consistent with aes-gcm-vaes-avx2.S and also the
BoringSSL port of this code.
No functional changes.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20251002023117.37504-6-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@kernel.org>