This code was added with 34b31da486 ("phy: fixed_phy: Set supported
speed in phydev") 10 yrs ago. The commit message of this change
mentions a use case involving callback adjust_link of struct
dsa_switch_driver. This struct doesn't exist any longer, and in general
usage of the legacy fixed PHY has been removed from DSA with the switch
to phylink.
Note: Supported and advertised modes are now set by phy_probe() when
the fixed PHY is attached to the netdev and bound to the genphy driver.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/3abaa3c5-fbb9-4052-9346-6cb096a25878@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function 'mpc_rcvd_sweep_req(mpcginfo)' is called conditionally
from function 'ctcmpc_unpack_skb'. It frees passed mpcginfo.
After that a call to function 'kfree' in function 'ctcmpc_unpack_skb'
frees it again.
Remove 'kfree' call in function 'mpc_rcvd_sweep_req(mpcginfo)'.
Bug detected by the clang static analyzer.
Fixes: 0c0b20587b ("s390/ctcm: fix potential memory leak")
Reviewed-by: Aswin Karuvally <aswin@linux.ibm.com>
Signed-off-by: Aleksei Nikiforov <aleksei.nikiforov@linux.ibm.com>
Signed-off-by: Aswin Karuvally <aswin@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20251112182724.1109474-1-aswin@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The libmnl dependency has been removed from libynl back in
commit 73395b4381 ("tools: ynl: remove the libmnl dependency")
Remove it from the ynltool Makefile.
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20251115225508.1000072-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
fbnic supports pause frames. When pause frames are enabled presumably
user expects lossless operation from the NIC. Make sure we configure
RDE (Rx DMA Engine) to DROP_NEVER mode to avoid discards due to delays
in fetching Rx descriptors from the host.
While at it enable DROP_NEVER when NIC only has a single queue
configured. In this case the NIC acts as a FIFO so there's no risk
of head-of-line blocking other queues by making RDE wait. If pause
is disabled this just moves the packet loss from the DMA engine to
the Rx buffer.
Remove redundant call to fbnic_config_drop_mode_rcq(), introduced by
commit 0cb4c0a137 ("eth: fbnic: Implement Rx queue
alloc/start/stop/free"). This call does not add value as
fbnic_enable_rcq(), which is called immediately afterward, already
handles this.
Although we do not support autoneg at this time, preserve tx_pause in
.mac_link_up instead of fbnic_phylink_get_pauseparam()
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20251113232610.1151712-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Breno Leitao says:
====================
net: mlx: migrate to new get_rx_ring_count ethtool API
This series migrates the mlx4 and mlx5 drivers to use the new
.get_rx_ring_count() callback introduced in commit 84eaf4359c ("net:
ethtool: add get_rx_ring_count callback to optimize RX ring queries").
Previously, these drivers handled ETHTOOL_GRXRINGS within the
.get_rxnfc() callback. With the dedicated .get_rx_ring_count() API, this
handling can be extracted and simplified.
For mlx5, this affects both the ethernet and IPoIB drivers. The
ETHTOOL_GRXRINGS handling was previously kept in .get_rxnfc() to support
"ethtool -x" when CONFIG_MLX5_EN_RXNFC=n, but this is no longer
necessary with the new dedicated callback.
Note: The mlx4 changes are compile-tested only, while mlx5 changes were
properly tested.
====================
Link: https://patch.msgid.link/20251113-mlx_grxrings-v1-0-0017f2af7dd0@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 84eaf4359c ("net: ethtool: add get_rx_ring_count callback to
optimize RX ring queries") added specific support for GRXRINGS callback,
simplifying .get_rxnfc.
Remove the handling of GRXRINGS in .get_rxnfc() by moving it to the new
.get_rx_ring_count() for both the mlx5 ethernet and IPoIB drivers.
The ETHTOOL_GRXRINGS handling was previously kept in .get_rxnfc() to
support "ethtool -x" when CONFIG_MLX5_EN_RXNFC=n. With the new
dedicated .get_rx_ring_count() callback, this is no longer necessary.
This simplifies the RX ring count retrieval and aligns mlx5 with the new
ethtool API for querying RX ring parameters.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20251113-mlx_grxrings-v1-2-0017f2af7dd0@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 84eaf4359c ("net: ethtool: add get_rx_ring_count callback to
optimize RX ring queries") added specific support for GRXRINGS callback,
simplifying .get_rxnfc.
Remove the handling of GRXRINGS in .get_rxnfc() by moving it to the new
.get_rx_ring_count().
This simplifies the RX ring count retrieval and aligns mlx4 with the new
ethtool API for querying RX ring parameters. This is compiled tested
only.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20251113-mlx_grxrings-v1-1-0017f2af7dd0@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend cpu_cache_invalidate_memregion() to support invalidating a
particular range of memory by introducing start and length parameters.
Control of types of invalidation is left for when use cases turn up. For
now everything is Clean and Invalidate.
Where the range is unknown, use the provided cpu_cache_invalidate_all()
helper to act as documentation of intent in a fashion that is clearer than
passing (0, -1) to cpu_cache_invalidate_memregion().
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The res_desc parameter was originally introduced for documentation purposes
and with the idea that with HDM-DB CXL invalidation could be triggered from
the device. That has not come to pass and the continued existence of the
option is confusing when we add a range in the following patch which might
not be a strict subset of the res_desc. So avoid that confusion by dropping
the parameter.
Link: https://lore.kernel.org/linux-mm/686eedb25ed02_24471002e@dwillia2-xfh.jf.intel.com.notmuch/
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The pic64gx use the same IP than mpfs, therefore add compatibility with
mpfs as fallback.
Signed-off-by: Pierre-Henry Moussay <pierre-henry.moussay@microchip.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
nvkm_falcon_fw::boot is allocated, but no one frees it. This causes a
kmemleak warning.
Make sure this data is deallocated.
Fixes: 2541626cfb ("drm/nouveau/acr: use common falcon HS FW code for ACR FWs")
Signed-off-by: Nam Cao <namcao@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patch.msgid.link/20251117084231.2910561-1-namcao@linutronix.de
If a file removal races with another operation that updates its
attributes, then skip the change to nlink, and just mark the attributes
as being stale.
Reported-by: Aiden Lambert <alambert48@gatech.edu>
Fixes: 59a707b0d4 ("NFS: Ensure we revalidate the inode correctly after remove or rename")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Implement the `AsBusDevice` trait for converting a `Device` reference to a
bus device reference for all bus devices.
The `AsBusDevice` trait allows abstractions to provide the bus device in
class device callbacks. It must not be used by drivers and is intended for
bus and class device abstractions only.
Signed-off-by: Markus Probst <markus.probst@posteo.de>
Link: https://patch.msgid.link/20251027200547.1038967-2-markus.probst@posteo.de
[ * Remove unused import.
* Change visibility of AsBusDevice to public.
* Fix build for USB.
* Add impl for I2cClient.
- Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Introduce the `num` module, which will provide numerical extensions and
utilities for the kernel.
For now, introduce the `Integer` trait, which is implemented for all
primitive integer types to provides their core properties to generic
code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://patch.msgid.link/20251108-bounded_ints-v4-1-c9342ac7ebd1@nvidia.com
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Similar to the RK3288, the RK3368 has two different implementations of
the PWM block inside the SoC - the newer ones that we have a driver for
and that is used on every SoC and a previous variant that was likely
left as a fallback if the new one creates problems.
The devicetree is already set up for the new variant, so make sure
we actually use it - similar to the RK3288.
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Link: https://patch.msgid.link/20251021074254.87065-4-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a new `rust_i2c_client` sample, showing how to create a new
i2c client using `i2c::Registration`
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Igor Korotin <igor.korotin.linux@gmail.com>
Link: https://patch.msgid.link/20251116162210.171542-1-igor.korotin.linux@gmail.com
[ * Remove dependency to I2C_CHARDEV, depend on I2C=y.
* Remove unnecessary impl Drop for SampleDriver.
* Rename i2c::Registration, import Devres.
* Fixup module description.
* Add new source file to MAINTAINERS.
- Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Add a new `rust_driver_i2c` sample, showing how to create a new
i2c driver using ACPI/OF/Legacy ID tables.
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Igor Korotin <igor.korotin.linux@gmail.com>
Link: https://patch.msgid.link/20251116162204.171518-1-igor.korotin.linux@gmail.com
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
In addition to the basic I2C device support, add rust abstractions
upon `i2c_new_client_device`/`i2c_unregister_device` C functions.
Implement the core abstractions needed for manual creation/deletion
of I2C devices, including:
* `i2c::Registration` — a NonNull pointer created by the function
`i2c_new_client_device`
* `i2c::I2cAdapter` — a ref counted wrapper around `struct i2c_adapter`
* `i2c::I2cBoardInfo` — a safe wrapper around `struct i2c_board_info`
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Igor Korotin <igor.korotin.linux@gmail.com>
Link: https://patch.msgid.link/20251116162154.171493-1-igor.korotin.linux@gmail.com
[ Remove unnecessary safety comment. - Danilo ]
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
amdgpu:
- RAS updates
- GC12 DCC P2P fix
- Documentation fixes
- Power limit code cleanup
- Userq updates
- VRR fix
- SMART OLED support
- DSC refactor for DCN 3.5
- Replay updates
- DC clockgating updates
- HDCP refactor
- ISP fix
- SMU 13.0.12 updates
- JPEG 5.0.1 fix
- VCE1 support
- Enable DC by default on SI
- Refactor CIK and SI enablement
- Enable amdgpu by default for CI dGPUs
- XGMI fixes
- SR-IOV fixes
- Memory allocation critical path fixes
- Enable amdgpu by default on SI dGPUs
amdkfd:
- Relax checks on save area overallocations
- Fix GPU mappings after prefetch
radeon:
- Refactor CIK and SI enablement
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQgO5Idg2tXNTSZAr293/aFa7yZ2AUCaReBigAKCRC93/aFa7yZ
2JqCAQDZYnl6lkfzXcm3z5qqI3DmEyREO75hn0IEffyehAhUYwD9FpC48tTCyzeY
1MQZ+ORH12VXuiT4Y+wBIiFetQV96QA=
=uThs
-----END PGP SIGNATURE-----
Merge tag 'amd-drm-next-6.19-2025-11-14' of https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-6.19-2025-11-14:
amdgpu:
- RAS updates
- GC12 DCC P2P fix
- Documentation fixes
- Power limit code cleanup
- Userq updates
- VRR fix
- SMART OLED support
- DSC refactor for DCN 3.5
- Replay updates
- DC clockgating updates
- HDCP refactor
- ISP fix
- SMU 13.0.12 updates
- JPEG 5.0.1 fix
- VCE1 support
- Enable DC by default on SI
- Refactor CIK and SI enablement
- Enable amdgpu by default for CI dGPUs
- XGMI fixes
- SR-IOV fixes
- Memory allocation critical path fixes
- Enable amdgpu by default on SI dGPUs
amdkfd:
- Relax checks on save area overallocations
- Fix GPU mappings after prefetch
radeon:
- Refactor CIK and SI enablement
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patch.msgid.link/20251114192553.442621-1-alexander.deucher@amd.com
Driver Changes:
Fixes/improvements/new stuff:
- Avoid lock inversion when pinning to GGTT on CHV/BXT+VTD (Janusz Krzysztofik)
- Use standard API for seqcount read in TLB invalidation [gt] (Andi Shyti)
Miscellaneous:
- Wait longer for threads in migrate selftest on CHV/BXT+VTD (Janusz Krzysztofik)
- Wait for page_sizes_gtt in gtt selftest on CHV/BXT+VTD (Janusz Krzysztofik)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tursulin@igalia.com>
Link: https://patch.msgid.link/aRdXOAKlTVX_b0en@linux
Update header inclusions to follow IWYU (Include What You Use)
principle.
In particular, replace of_gpio.h, which is subject to removal by the
GPIOLIB subsystem, with the respective headers that are being used by the
driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251114185534.3287497-1-andriy.shevchenko@linux.intel.com
pci_epc_mem_alloc_addr() allocates a CPU address from the ATU window phys
base and a page number. Set the ep->page_size so the resulting CPU address
is correctly aligned with the ATU required alignment.
Fixes: 151f3d29ba ("PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25")
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
[mani: added fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251114-atu_align_ep-v1-1-88da5366fa04@foss.st.com
If the host has deasserted PERST# and started link training before the link
is started on EP side, enabling LTSSM before the endpoint registers are
initialized in the perst_irq handler results in probing incorrect values.
Thus, wait for the PERST# level-triggered interrupt to start link training
at the end of initialization and cleanup the stm32_pcie_[start stop]_link
functions.
Fixes: 151f3d29ba ("PCI: stm32-ep: Add PCIe Endpoint support for STM32MP25")
Signed-off-by: Christian Bruel <christian.bruel@foss.st.com>
[mani: added fixes tag]
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
[bhelgaas: wrap line]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://patch.msgid.link/20251114-perst_ep-v1-1-e7976317a890@foss.st.com
On a system which support SME but not SVE we can now disable streaming mode
via ptrace by writing FPSIMD formatted data through NT_ARM_SVE with a VL of
0. Extend fp-ptrace to cover rather than skip these cases, relax the check
for SVE writes of FPSIMD format data to not skip if SME is supported and
accept 0 as the VL when performing the ptrace write.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
In order to allow exiting streaming mode on systems with SME but not SVE
we allow writes of FPSIMD format data via NT_ARM_SVE even when SVE is not
supported, add a test case that covers this to sve-ptrace.
We do not support reads.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Currently it is not possible to disable streaming mode via ptrace on SME
only systems, the interface for doing this is to write via NT_ARM_SVE but
such writes will be rejected on a system without SVE support. Enable this
functionality by allowing userspace to write SVE_PT_REGS_FPSIMD format data
via NT_ARM_SVE with the vector length set to 0 on SME only systems. Such
writes currently error since we require that a vector length is specified
which should minimise the risk that existing software is relying on current
behaviour.
Reads are not supported since I am not aware of any use case for this and
there is some risk that an existing userspace application may be confused if
it reads NT_ARM_SVE on a system without SVE. Existing kernels will return
FPSIMD formatted register state from NT_ARM_SVE if full SVE state is not
stored, for example if the task has not used SVE. Returning a vector length
of 0 would create a risk that software would try to do things like allocate
space for register state with zero sizes, while returning a vector length of
128 bits would look like SVE is supported. It seems safer to just not make
the changes to add read support.
It remains possible for userspace to detect a SME only system via the ptrace
interface only since reads of NT_ARM_SSVE and NT_ARM_ZA will succeed while
reads of NT_ARM_SVE will fail. Read/write access to the FPSIMD registers in
non-streaming mode is available via REGSET_FPR.
sve_set_common() already avoids allocating SVE storage when doing a FPSIMD
formatted write and allocating SME storage when doing a NT_ARM_SVE write so
we change the function to validate the new case and skip setting a vector
length for it.
The aim is to make a minimally invasive change, no operation that would
previously have succeeded will be affected, and we use a previously
defined interface in new circumstances rather than define completely new
ABI.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: David Spickett <david.spickett@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
drm/i915 feature pull #2 for v6.19:
Features and functionality:
- Add initial display support for Xe3p_LPD, display version 35 (Sai Teja, Matt
R, Gustavo, Matt A, Ankit, Juha-pekka, Luca, Ravi Kumar)
- Compute LT PHY HDMI params when port clock not in predefined tables (Suraj)
Refactoring and cleanups:
- Refactor intel_frontbuffer split between i915, xe, and display (Ville)
- Clean up intel_de_wait_custom() usage (Ville)
- Unify display register polling interfaces (Ville)
- Finish removal of the expensive format info lookups (Ville)
- Cursor code cleanups (Ville)
- Convert intel_rom interfaces to struct drm_device (Jani)
Fixes:
- Fix uninitialized variable in DSI exec packet (Jonathan)
- Fix PIPEDMC logging (Alok Tiwari)
- Fix PSR pipe to vblank conversion (Jani)
- Fix intel_frontbuffer lifetime handling (Ville)
- Disable Panel Replay on DP MST for the time being (Imre)
Merges:
- Backmerge drm-next to get the drm_print.h changes (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patch.msgid.link/b131309bb7310ab749f1770aa6e36fa8d6a82fa5@intel.com
Several static functions in kernel/power/swap.c were described using the
kernel-doc comment style (/** ... */) even though they are not exported
or referenced by generated documentation. This led to kernel-doc warnings
and stylistic inconsistencies.
Convert these unnecessary kernel-doc blocks to regular C comments,
remove comment blocks that are no longer useful, relocate comments to
more appropriate positions where needed, and fix a few "Return:"
descriptions that were either missing or incorrectly formatted.
No functional changes.
Signed-off-by: Sunday Adelodun <adelodunolaoluwa@yahoo.com>
[ rjw: Subject adjustment, changelog edits, comment edits ]
Link: https://patch.msgid.link/20251114220438.52448-1-adelodunolaoluwa@yahoo.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some of the datasheet links contained .pdf suffix which resulted in 404.
This patch updates the links to the correct URLs on Renesas website.
Signed-off-by: Igor Reznichenko <igor@reznichenko.net>
Link: https://lore.kernel.org/r/20251115182908.1357793-1-igor@reznichenko.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
loop devices under heavy stress-ng loop streessor can trigger many
capacity change events in a short time. Each event prints an info
message from set_capacity_and_notify(), flooding the console and
contributing to soft lockups on slow consoles.
Switch the printk in set_capacity_and_notify() to
pr_info_ratelimited() so frequent capacity changes do not spam
the log while still reporting occasional changes.
Cc: stable@vger.kernel.org
Signed-off-by: Li Chen <chenl311@chinatelecom.cn>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Extended linear cache unit testing support
- Standardize CXL auto region size
- Add cxl_test CFMWS support for extended linear cache
- Add support for acpi extended linear cache
If there is a flood of faults then the MMU can become saturated while it
waits for the kernel to process the first fault and resume it, so that
the GMU becomes blocked. This is mainly a problem when the kernel reads
the state of the GPU for a devcoredump, because this takes a while. If
we timeout waiting for the GMU, check if this has happened and retry
after we're finished.
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/664685/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
If the rootfs have a legacy A200 firmware, currently the driver will
complain each time the hw is reinited (which can happen a lot). E.g.
with GL testsuite the hw is reinited after each test, spamming the
console.
Make sure that the message is printed only once: when we detect the
firmware that doesn't support protection.
Fixes: 302295070d ("drm/msm/a2xx: support loading legacy (iMX) firmware")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/688098/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
The crashstate_get_bos() function allocates memory for `state->bos`
using kcalloc(), but the vmbind path does not check for allocation
failure before dereferencing it in the following drm_gpuvm_for_each_va()
loop. This could lead to a NULL pointer dereference if memory allocation
fails.
Fix this by wrapping the drm_gpuvm_for_each_va() loop with a NULL check
on state->bos, similar to the safety check in the non-vmbind path.
Fixes: af9aa6f316 ("drm/msm: Crashdump support for sparse")
Signed-off-by: Huiwen He <hehuiwen@kylinos.cn>
Patchwork: https://patchwork.freedesktop.org/patch/687556/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
crashstate_get_vm_logs() did not check the return value of
kmalloc_array(). In low-memory situations, kmalloc_array() may return
NULL, leading to a NULL pointer dereference when the function later
accesses state->vm_logs.
Fix this by checking the return value of kmalloc_array() and setting
state->nr_vm_logs to 0 if allocation fails.
Fixes: 9edc52967c ("drm/msm: Add VM logging for VM_BIND updates")
Signed-off-by: Huiwen He <hehuiwen@kylinos.cn>
Patchwork: https://patchwork.freedesktop.org/patch/687555/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
On BCM6358 (and also observed on BCM6368) the controller appears to
only generate as many SPI clocks as bytes that have been written into
the TX FIFO. For RX-only transfers the driver programs the transfer
length in SPI_MSG_CTL but does not write anything into the FIFO, so
chip select is deasserted early and the RX transfer segment is never
fully clocked in.
A concrete failing case is a three-transfer MAC address read from
SPI-NOR:
- TX 0x03 (read command)
- TX 3-byte address
- RX 6 bytes (MAC)
In contrast, a two-transfer JEDEC-ID read (0x9f + 6-byte RX) works
because the driver uses prepend_len and writes dummy bytes into the
TX FIFO for the RX part.
Fix this by writing 0xff dummy bytes into the TX FIFO for RX-only
segments so that the number of bytes written to the FIFO matches the
total message length seen by the controller.
Fixes: b17de07606 ("spi/bcm63xx: work around inability to keep CS up")
Signed-off-by: Hang Zhou <929513338@qq.com>
Link: https://patch.msgid.link/tencent_7AC88FCB3076489A4A7E6C2163DF1ACF8D06@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It is a requirement that DT overlays in the kernel are applied at build
time to a base DTB in order to validate they can be applied and to
validate them against the DT schemas. DT overlays on their own may be
incomplete and can't be validated.
Add a kbuild check so this doesn't have to be checked and fixed
periodically.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
The Devicetree Specification states:
The root of the interrupt tree is determined when traversal of the
interrupt tree reaches an interrupt controller node without an
interrupts property and thus no explicit interrupt parent.
However, of_irq_init() gratuitously assumes that a node without
interrupts has an actual interrupt parent if it finds an
interrupt-parent property higher up in the device tree. Hence when such
a property is present (e.g. in the root node), the root interrupt
controller may not be detected as such, causing a panic:
OF: of_irq_init: children remain, but no parents
Kernel panic - not syncing: No interrupt controller found.
Commit e91033621d ("of/irq: Use interrupts-extended to find
parent") already fixed a first part, by checking for the presence of an
interrupts-extended property. Fix the second part by only calling
of_irq_find_parent() when an interrupts property is present.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/fbe6fc3657070fe2df7f0529043542b52b827449.1763116833.git.geert+renesas@glider.be
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
There are no longer any board files including the DaVinci SPI platform
data header. Let's move the bits and pieces that are used in the driver
into the driver .c file itself and remove the header.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://patch.msgid.link/20251117-davinci-spi-v2-1-cd799d17f04a@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_bus_default_match() function appears to have been copied from
of_bus_default_flags_match() with some modifications.
However, the comment was left unchanged and still describes the behavior
of of_bus_default_flags_match(), it is incorrect and misleading, remove it.
Signed-off-by: Yuntao Wang <yuntao.wang@linux.dev>
Fixes: 6e5773d52f ("of/address: Fix WARN when attempting translating non-translatable addresses")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://patch.msgid.link/20251112143520.233870-11-yuntao.wang@linux.dev
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
The binding is already defined in mfd/stericsson,db8500-prcmu.yaml and none
of 'the tripN.*' properties appear to be in use.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://patch.msgid.link/20251030195234.439141-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Convert the brcm,sr-thermal binding to DT schema format. It's a
straight-forward conversion. "polling-delay", "thermal-sensors", and
"temperature" all apply to the thermal zones, not the sensor node.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20251013215810.783006-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
For better readability, it is recommended to insert a newline before the
'status' property. Adjust the examples accordingly.
Signed-off-by: David Heidelberg <david@ixit.cz>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20251023-docs-dt-newline-v1-1-1bf5e0040c0b@ixit.cz
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>