Data writes for the ssd130x 4-wire SPI protocol need special handling, due
the Data/Command control (D/C) pin having to be toggled prior to the write.
The regmap API only allowed drivers to provide .reg_{read,write} callbacks
to do per register read/write, but didn't provide a way for drivers to do
the same for bulk read/writes.
For this reason, a custom regmap bus was used by the driver just to define
a bulk write callback that implements the D/C pin toggling. But the regmap
API has been extended to support defining bulk read/write handlers, so the
custom regmap bus is not needed anymore and could just be dropped.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220618174338.2253021-1-javierm@redhat.com
Add FourCCs for two missing permutations of the packed YUV 4:4:4 color
components, namely AVUY and XVUY.
These formats are needed by the NXP i.MX8 ISI. While the ISI is
supported by a V4L2 device (corresponding formats have been submitted to
V4L2), it is handled in userspace by libcamera, which uses DRM FourCCs
for pixel formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220616185210.22018-1-laurent.pinchart@ideasonboard.com
Setting err_rq_idx_valid field in QP context when the AE source of the
AEQE is not associated with an RQ causes the firmware flush to fail.
Set err_rq_idx_valid field in QP context only if it is associated with an
RQ. Additionally, cleanup the redundant setting of this field in
irdma_process_aeq.
Fixes: 44d9e52977 ("RDMA/irdma: Implement device initialization definitions")
Link: https://lore.kernel.org/r/20220705230815.265-8-shiraz.saleem@intel.com
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When an application listens on a wildcard address, and there are VLAN and
non-VLAN IP addresses, iWARP connection establishemnt can fail if the listen
node VLAN ID does not match.
Fix this by checking the vlan_id only if not a wildcard listen node.
Fixes: 146b9756f1 ("RDMA/irdma: Add connection manager")
Link: https://lore.kernel.org/r/20220705230815.265-7-shiraz.saleem@intel.com
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
During a destroy CQ an interrupt may cause processing of a CQE after CQ
resources are freed by irdma_cq_free_rsrc(). Fix this by moving the call
to irdma_cq_free_rsrc() after the irdma_sc_cleanup_ceqes(), which is
called under the cq_lock.
Fixes: b48c24c2d7 ("RDMA/irdma: Implement device supported verb APIs")
Link: https://lore.kernel.org/r/20220705230815.265-6-shiraz.saleem@intel.com
Signed-off-by: Bartosz Sobczak <bartosz.sobczak@intel.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Adapt the resource distribution algorithm in irdma_cfg_fpm_val to be more
QP oriented. If the configuration is too big for the available memory,
trim the MR and PBLE's first before trimming the QPs. This also avoids
having to double QPs requested as input to algorithm for GEN1 devices.
Link: https://lore.kernel.org/r/20220705230815.265-5-shiraz.saleem@intel.com
Signed-off-by: Nayan Kumar <nayan.kumar@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The invalid state error returned by the Control Queue-Pair (CQP) is not a
critical error.
Add it to the irdma_noncrit_err_list and drop reporting it as device error
message.
Link: https://lore.kernel.org/r/20220705230815.265-4-shiraz.saleem@intel.com
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
To assist with debugging add the Asynchronous Event (AE) source when
logging the abnormal AE error log message.
Link: https://lore.kernel.org/r/20220705230815.265-3-shiraz.saleem@intel.com
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Level 2 Physical Buffer List Entry (PBLE) is currently not supported for
Fast MRs which limits memory registrations to 256K pages.
Adapt irdma_set_page and irdma_alloc_mr to allow for 2 level PBLEs.
Link: https://lore.kernel.org/r/20220705230815.265-2-shiraz.saleem@intel.com
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
I've stumbled over this while reviewing patches for DMA-buf and it looks
like we completely messed the locking up here.
In general most TTM function should only be called while holding the
appropriate BO resv lock. Without this we could break the internal
buffer object state here.
Only compile tested!
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 43676605f8 ("drm/ttm: Add vmap/vunmap to TTM and TTM GEM helpers")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220715111533.467012-1-christian.koenig@amd.com
The sys_clk frequency is 165.625MHz. The register reference of the
Generic Clock controller lists the CPU clock as 600MHz, the DDR clock as
300MHz and the SYS clock as 162.5MHz. This is wrong. It was first
noticed during the fan driver development and it was measured and
verified via the CLK_MON output of the SoC which can be configured to
output sys_clk/64.
The core PLL settings (which drives the SYS clock) seems to be as
follows:
DIVF = 52
DIVQ = 3
DIVR = 1
With a refernce clock of 25MHz, this means we have a post divider clock
Fpfd = Fref / (DIVR + 1) = 25MHz / (1 + 1) = 12.5MHz
The resulting VCO frequency is then
Fvco = Fpfd * (DIVF + 1) * 2 = 12.5MHz * (52 + 1) * 2 = 1325MHz
And the output frequency is
Fout = Fvco / 2^DIVQ = 1325MHz / 2^3 = 165.625Mhz
This all adds up to the constrains of the PLL:
10MHz <= Fpfd <= 200MHz
20MHz <= Fout <= 1000MHz
1000MHz <= Fvco <= 2000MHz
Fixes: 290deaa10c ("ARM: dts: add DT for lan966 SoC and 2-port board pcb8291")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220326194028.2945985-1-michael@walle.cc
There is no need to EXPORT the functions hwa742_update_window_async()
and omapfb_update_window_async() since they are not used anywhere inside
or outside the kernel tree.
Signed-off-by: Helge Deller <deller@gmx.de>
As of v2.1.0, falcon_decode_var() contains a quirk to fix a rounding
error, as explained by Günther Kelleter on Fri, 30 Aug 1996:
This diff removes the now obsolete Falcon video option "pwrsave", and
fixes a rounding error that is triggered by the resolution switching X
server (those who use the pixel clock value 39722 in their /etc/fb.modes
should change it to 39721).
However, this causes the modified video mode returned by
falcon_decode_var() to not match the video mode returned by
falcon_encode_var(). Fix this by dropping the quirk.
Unfortunately /etc/fb.modes in fbset was never updated, so the
"640x480-60" mode still contains the wrong pixclock.
Hence this change may introduce a regression.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Several definitions and variables are unused.
Some variables are set but further unused.
Remove them.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The pixclock values in the vga and vga70 modes are wrong, as they should
use the 25.175 MHz clock instead of the 32 MHz clock.
Swap the left and right margins to match f25.{right,left} (struct
pixel_clock declares them in a different order), and update the hsync
lengths to match what the driver programs by default.
Correct the (wrong) floating-point vrefresh value for the vga mode.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The vertical refresh rate for the TT High video mode (1280x960) is
wrong. Fortunately this field is not really used.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Arbitrary pointers can be passed to functions accepting "void *" without
casting.
Remove the casts, as they make it impossible to validate types.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
There is no need to cast fb_info.par to "struct atafb_par *", as the
former has type "void *".
Remove the casts, as they make it impossible to validate types.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The red, green, and blue color values are 16-bit, while the external
graphics hardware registers are 8-bit.
Add the missing conversion from 16-bit to 8-bit.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Currently, the "inverse" option does not do anything, as it just sets a
flag, which is further unused.
Fix this by calling fb_invert_cmaps() instead, like other drivers do.
As this only affects the console colormap, this does not affect X.
Update the documentation to match the actual behavior.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
Vertical wrap is not supported (fb_fix_screeninfo.ywrapstep = 0), hence
there is no point in setting the FB_VMODE_YWRAP flag in video modes.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The fb_pan_display() function in the core already takes care of
validating the panning parameters before calling the driver's
.fb_pan_display() callback, and of updating the panning state
afterwards, so there is no need to repeat that in the driver.
Remove the duplicate code.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Helge Deller <deller@gmx.de>
The various *fb_setup() and *fb_init() functions are only used locally,
so they should be static. Most of them do not need forward
declarations, so remove these where appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Helge Deller <deller@gmx.de>
cirrusfb_zorro_unregister() is only used locally, hence make it static.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Helge Deller <deller@gmx.de>
sa1100fb_setup() has been unused since the beginning of Linux git
history.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Helge Deller <deller@gmx.de>
The fb_pan_display() function in the core already takes care of
validating most panning parameters before calling the driver's
.fb_pan_display() callback, and of updating the panning state
afterwards, so there is no need to repeat that in the driver.
Remove the duplicate code.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Helge Deller <deller@gmx.de>
Free slots tracking assumes that slots in a segment can be allocated to
fulfill a request. This implies that slots in a segment should belong to
the same area. Although the possibility of a violation is low, it is better
to explicitly enforce segments won't span multiple areas by adjusting the
number of slabs when configuring areas.
Signed-off-by: Chao Gao <chao.gao@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
default_nslabs are rounded up in two cases with exactly same comments.
Add a simple wrapper to reduce duplicate code/comments. It is preparatory
to adding more logics into the round-up.
No functional change intended.
Signed-off-by: Chao Gao <chao.gao@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit 20347fca71 ("swiotlb: split up the global swiotlb lock") splits
io_tlb_mem into multiple areas. Each area has its own lock and index. The
global ones are not used so remove them.
Signed-off-by: Chao Gao <chao.gao@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Don't dereference "mem" after it has been freed. Flip the
two kfree()s around to address this bug.
Fixes: 26ffb91fa5e0 ("swiotlb: split up the global swiotlb lock")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add compatible for EPSS CPUFREQ-HW on SM6375.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
msm8939 will uses this driver instead of the generic dt-cpufreq. Add to the
compatible list.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
A number of devices listed in drivers/cpufreq/qcom-cpufreq-nvmem.c appear
to be missing from the compatible list.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Adding missing compat entries to the cpufreq node
Documentation/devicetree/bindings/cpufreq/qcom-cpufreq-nvmem.yaml shows up
a dt_binding_check in this file.
opp-v2-kryo-cpu.example.dtb: /: cpus:cpu@0: 'power-domains' is a required property
opp-v2-kryo-cpu.example.dtb: /: cpus:cpu@0: 'power-domain-names' is a required property
opp-v2-kryo-cpu.example.dtb: /: opp-table-0:opp-307200000: 'required-opps' is a required property
Fixes: ec24d1d554 ("dt-bindings: opp: Convert qcom-nvmem-cpufreq to DT schema")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
From a state where all policy->related_cpus are offline, putting one
of the policy's CPU back online re-activates the policy by:
1. Calling cpufreq_driver->online()
2. Setting the CPU in policy->cpus
qcom_cpufreq_hw_cpu_online() makes use of policy->cpus. Thus 1. and 2.
should be inverted to avoid having a policy->cpus empty. The
qcom-cpufreq-hw is the only driver affected by this.
Signed-off-by: Pierre Gondois <pierre.gondois@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Details is added about "caps" attribute group in the ABI documentation.
This is used to expose some of the PMU attributes in "caps"
directory under : /sys/bus/event_source/devices/<dev>/. The dev/caps
will contain information about features that platform specific PMU
supports.
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220520084630.15181-2-atrajeev@linux.vnet.ibm.com
Add caps support under "/sys/bus/event_source/devices/<pmu>/"
for powerpc. This directory can be used to expose some of the
specific features that powerpc PMU supports to the user.
Example: pmu_name. The name of PMU registered will depend on
platform, say power9 or power10 or it could be Generic Compat
PMU.
Currently the only way to know which is the registered
PMU is from the dmesg logs. But clearing the dmesg will make it
difficult to know exact PMU backend used. And even extracting
from dmesg will be complicated, as we need to parse the dmesg
logs and add filters for pmu name. Whereas by exposing it via
caps will make it easy as we just need to directly read it from
the sysfs.
Add a caps directory to /sys/bus/event_source/devices/cpu/
for power8, power9, power10 and generic compat PMU in respective
PMU driver code. Update the pmu_name file under caps folder
in core-book3s using "attr_update".
The information exposed currently:
- pmu_name : Underlying PMU name from the driver
Example result with power9 pmu:
# ls /sys/bus/event_source/devices/cpu/caps
pmu_name
# cat /sys/bus/event_source/devices/cpu/caps/pmu_name
POWER9
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220520084630.15181-1-atrajeev@linux.vnet.ibm.com
When booting on a machine that uses the compat pmu driver we see this:
[ 0.071192] GENERIC_COMPAT performance monitor hardware support registered
Which is a bit shouty. Give it a nicer name.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220610044006.2095806-1-joel@jms.id.au
kernel test robot throws below warning ->
arch/ia64/include/asm/mmu_context.h: In function 'reload_context':
arch/ia64/include/asm/mmu_context.h:127:48: warning: variable
'old_rr4' set but not used [-Wunused-but-set-variable]
127 | unsigned long rr0, rr1, rr2, rr3, rr4, old_rr4;
Add it under CONFIG_HUGETLB_PAGE
Link: https://lkml.kernel.org/r/20220626022114.4020-1-jrdr.linux@gmail.com
Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Booting with vsyscall=xonly results in the following vsyscall VMA:
ffffffffff600000-ffffffffff601000 --xp ... [vsyscall]
Test does read from fixed vsyscall address to determine if kernel
supports vsyscall page but it doesn't work because, well, vsyscall
page is execute only.
Fix test by trying to execute from the first byte of the page which
contains gettimeofday() stub. This should work because vsyscall
entry points have stable addresses by design.
Alexey, avoiding parsing .config, /proc/config.gz and
/proc/cmdline at all costs.
Link: https://lkml.kernel.org/r/Ys2KgeiEMboU8Ytu@localhost.localdomain
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: <dylanbhatch@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Commit 7bc3e6e55a ("proc: Use a list of inodes to flush from proc")
moved proc_flush_task() behind __exit_signal(). Then, process systemd can
take long period high cpu usage during releasing task in following
concurrent processes:
systemd ps
kernel_waitid stat(/proc/tgid)
do_wait filename_lookup
wait_consider_task lookup_fast
release_task
__exit_signal
__unhash_process
detach_pid
__change_pid // remove task->pid_links
d_revalidate -> pid_revalidate // 0
d_invalidate(/proc/tgid)
shrink_dcache_parent(/proc/tgid)
d_walk(/proc/tgid)
spin_lock_nested(/proc/tgid/fd)
// iterating opened fd
proc_flush_pid |
d_invalidate (/proc/tgid/fd) |
shrink_dcache_parent(/proc/tgid/fd) |
shrink_dentry_list(subdirs) ↓
shrink_lock_dentry(/proc/tgid/fd) --> race on dentry lock
Function d_invalidate() will remove dentry from hash firstly, but why does
proc_flush_pid() process dentry '/proc/tgid/fd' before dentry
'/proc/tgid'? That's because proc_pid_make_inode() adds proc inode in
reverse order by invoking hlist_add_head_rcu(). But proc should not add
any inodes under '/proc/tgid' except '/proc/tgid/task/pid', fix it by
adding inode into 'pid->inodes' only if the inode is /proc/tgid or
/proc/tgid/task/pid.
Performance regression:
Create 200 tasks, each task open one file for 50,000 times. Kill all
tasks when opened files exceed 10,000,000 (cat /proc/sys/fs/file-nr).
Before fix:
$ time killall -wq aa
real 4m40.946s # During this period, we can see 'ps' and 'systemd'
taking high cpu usage.
After fix:
$ time killall -wq aa
real 1m20.732s # During this period, we can see 'systemd' taking
high cpu usage.
Link: https://lkml.kernel.org/r/20220713130029.4133533-1-chengzhihao1@huawei.com
Fixes: 7bc3e6e55a ("proc: Use a list of inodes to flush from proc")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216054
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Zhang Yi <yi.zhang@huawei.com>
Suggested-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Kalesh Singh <kaleshsingh@google.com>
Cc: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Remove the unused inode field of the autofs dentry info structure.
Link: https://lkml.kernel.org/r/165724460393.30914.6511330213821246793.stgit@donald.themaw.net
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The function autofs_mountpoint_changed() is unusual, add a comment about
two cases for which it is needed.
Link: https://lkml.kernel.org/r/165724459804.30914.10974834416046555127.stgit@donald.themaw.net
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The dentry info. field count is used to check if a dentry is in use
during expire. But, to be used for this the count field must account for
the presence of child dentries in a directory dentry.
Therefore it can also be used to check for an empty directory dentry which
can be done without having to to take an additional lock or account for
the presence of a readdir cursor dentry as is done by simple_empty().
Link: https://lkml.kernel.org/r/165724459238.30914.1504611159945950108.stgit@donald.themaw.net
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
If an autofs dentry is a mount root directory there's no ->mkdir() call to
set its count to one.
To make the dentry info count consistent for all autofs dentries set count
to one when the dentry info struct is allocated.
Link: https://lkml.kernel.org/r/165724458671.30914.2902424437132835325.stgit@donald.themaw.net
Signed-off-by: Ian Kent <raven@themaw.net>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
