It might be useful to drivers to be able to pass only the
link_conf pointer, rather than both the pointer and the
link_id; add the link_id to the link_conf to facility that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In station/client mode, the link data needs a bit more
initialization and destruction than just zero-init and
kfree() respectively, implement that.
This required some shuffling of the link data handling
in general, as we should set it up in setup and do the
teardown in teardown, otherwise we're asymmetric in
case of interface type changes.
Also stop using kfree_rcu(), we cannot guarantee that
nothing is scheduling things that live within the link
(e.g. the u.mgd.request_smps_work) until we're sure it
cannot be referenced anymore, therefore synchronize
instead. This isn't very efficient, but we can always
optimize it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least the quantenna driver calls wdev_chandef() here
which now requires the lock, so acquire it.
Fixes: 7b0a0e3c3a ("wifi: cfg80211: do some rework towards MLO link APIs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the split into keys[]/deflink.gtk[] arrays, WEP keys are
still installed into the keys[] array, but we didn't look them
up there. This meant they weren't deleted correctly.
Fix this by looking up the key there even if it's not pairwise
so we can be sure we don't have it.
Fixes: bfd8403add ("wifi: mac80211: reorg some iface data structs for MLD")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Separate out the connection downgrade flags from the ifmgd->flags
and put them into the link information instead. While at it, make
them a separate sparse type so we don't get confused about where
they belong and have static checking on correct handling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align the mac80211 implementation with P802.11be_D2.0.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Align the mac80211 implementation with P802.11be_D1.5.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a few places that check ps_sdata and/or the dynamic
PS timeout, but they're erroneous in case SUPPORTS_DYNAMIC_PS
is set by the driver.
Skip the entire recalculation in this case so we cannot get
into those paths elsewhere, and so we simplify this for the
purpose of implementing MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we don't really have multiple links, omit the link ID from
link debug prints, otherwise we change the format for all of
the existing drivers (most of which might never support MLO),
and also have extra noise in the logs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do address matching with link addresses as well.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multi-link operation, this cannot work as the req->bss pointer
will be NULL, and we'll need to do more work on this to really add
tracing for the MLO case here. Drop the BSS elements for now as
they're not the most useful thing, and it's hard to size things
correctly for the MLO case (without adding a lot of code that's
also executed when tracing isn't enabled.)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We might assign -1 to it in some cases when key is NULL,
which means the key_idx isn't used but can lead to a
warning from static checkers such as smatch.
Make the struct member signed simply to avoid that, we
only need a range of -1..3 anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since for an MLD station the default link is added together
with the add station command, allow also setting the link
MAC address.
Otherwise, it is needed to use the modify link API only
for setting the link MAC address.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since links can be added and removed dynamically, we need to
somehow protect the sdata->link[] and vif->link_conf[] array
pointers from disappearing when accessing them without locks.
RCU-ify the pointers to achieve this, which requires quite a
bit of rework.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since this will need to refer - at least in part - to the link
stations of an MLD, hold the wdev mutex for driver convenience.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we deal with links, and that requires looking at wdev links,
we should hold the wdev mutex for driver convenience.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Put the link_station_parameters structure in the station_parameters
structure (and remove the station_parameters fields already existing
in link_station_parameters).
Now, for an MLD station, the default link is added together with
the station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an API for adding/modifying/removing a link of a station.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to ieee80211_get_sband but get the sband of the link_conf.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
AP SMPS was removed and not needed anymore. Remove the leftovers.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Management frames are transmitted from link address and not device
address. Allow that.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check all the MLO links to decide whether offchannel TX is needed.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When checking whether or not to accept a frame in RX,
take into account the configured link addresses. Also
look up the link station correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Accept frames from all the links' channels.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211s_update_metric function uses sta_set_rate_info_tx
function to get struct rate_info data from ieee80211_tx_rate
struct, present in ieee80211_sta->deflink.tx_stats. However,
drivers can skip tx rate calculation by setting rate idx as
-1. Such drivers provides rate_info directly and hence
ieee80211s metric is updated incorrectly since ieee80211_tx_rate
has inconsistent data.
Add fix to use rate_info directly if present instead of
sta_set_rate_info_tx for updating ieee80211s metric.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://lore.kernel.org/r/20220701133611.544-1-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WDS needs 4addr packets to trigger AP for wlan0.sta creation.
However, the 4addr null frame is sent at a high rate so that
sometimes the AP can't receive it. Switch to using min rate.
Signed-off-by: Lian Chen <lian.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220714091636.59107-1-lian.chen@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In AP mode, multicast traffic is handled very differently from normal traffic,
especially if at least one client is in powersave mode.
This means that multicast packets can be buffered a lot longer than normal
unicast packets, and can eat up the AQL budget very quickly because of the low
data rate.
Along with the recent change to maintain a global PHY AQL limit, this can lead
to significant latency spikes for unicast traffic.
Since queueing multicast to hardware is currently not constrained by AQL limits
anyway, let's just exclude it from the AQL pending airtime calculation entirely.
Fixes: 8e4bac0671 ("wifi: mac80211: add a per-PHY AQL limit to improve fairness")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220713083444.86129-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We won't really have enough skbs to need a 64-bit cookie,
and on 32-bit platforms storing the 64-bit cookie into the
void *rate_driver_data doesn't work anyway. Switch back to
using just a 32-bit cookie and uintptr_t for the type to
avoid compiler warnings about all this.
Fixes: 4ee186fa7e ("wifi: mac80211_hwsim: fix race condition in pending packet")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove a variable here that was now set but never used.
Fixes: f276e20b18 ("wifi: mac80211: move interface config to new struct")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The console_stop() and console_start() functions call pr_flush().
When suspending, these functions are called by the serial subsystem
while the serial port is suspended. In this scenario, if there are
any pending messages, a call to pr_flush() will always result in a
timeout because the serial port cannot make forward progress. This
causes longer suspend and resume times.
Add a check in pr_flush() so that it will immediately timeout if
the consoles are suspended.
Fixes: 3b604ca812 ("printk: add pr_flush()")
Reported-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Tested-by: Todd Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20220715061042.373640-2-john.ogness@linutronix.de
The IOMMUv2 APIs (for supporting shared virtual memory with PASID)
configures the domain with IOMMU v2 page table, and sets DTE[Mode]=0.
This configuration cannot be supported on SNP-enabled system.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Link: https://lore.kernel.org/r/20220713225651.20758-10-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Since the Linux RNG no longer uses sha1_transform(), the SHA-1 library
is no longer needed unconditionally. Make it possible to build the
Linux kernel without the SHA-1 library by putting it behind a kconfig
option, and selecting this new option from the kconfig options that gate
the remaining users: CRYPTO_SHA1 for crypto/sha1_generic.c, BPF for
kernel/bpf/core.c, and IPV6 for net/ipv6/addrconf.c.
Unfortunately, since BPF is selected by NET, for now this can only make
a difference for kernels built without networking support.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SHA-1 is a crypto algorithm (or at least was intended to be -- it's not
considered secure anymore), so move it out of the top-level library
directory and into lib/crypto/.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
FIPS 140-3 introduced a requirement for the FIPS module to return
information about itself, specifically a name and a version. These
values must match the values reported on FIPS certificates.
This patch adds two files to read a name and a version from:
/proc/sys/crypto/fips_name
/proc/sys/crypto/fips_version
v2: removed redundant parentheses in config entries.
v3: move FIPS_MODULE_* defines to fips.c where they are used.
v4: return utsrelease.h inclusion
Signed-off-by: Simo Sorce <simo@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Variable nbytes is being assigned a value that is never read, it is
being re-assigned in the next statement in the while-loop. The
assignment is redundant and can be removed.
Cleans up clang scan-build warnings, e.g.:
arch/x86/crypto/blowfish_glue.c:147:10: warning: Although the value
stored to 'nbytes' is used in the enclosing expression, the value
is never actually read from 'nbytes'
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a engine status register that can be used to check if the
different HW crypto engines are enabled. Check that first and then only
try to enable the engines if they are not already on.
This has a couple benefits. First we don't need to use match_data for
this. Second, this driver can now work on HS devices where the engine
control registers are read-only and writing causes a firewall exception.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Setting these individually gives a better picture of supported
functions at a glance. Plus if the list changes an unwanted
one will not accidentally get set with GENMASK.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Initialize sha_dd with platform_get_drvdata() when declaring it.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Initialize sha_dd with platform_get_drvdata() when declaring it.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam has its own special NAPI weights. It's also a crypto device
so presumably it can't be used for packet Rx. Switch to the (new)
correct API.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so pdata is never NULL.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so dd is never NULL.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so dd is never NULL.
This is a preparation for making platform remove callbacks return void.
While touching this driver remove an assignment without effect.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so dd is never NULL.
This is a preparation for making platform remove callbacks return void.
While touching this driver remove a stray empty line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The remove callback is only called after probe completed successfully.
In this case platform_set_drvdata() was called with a non-NULL argument
and so tdes_dd is never NULL.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
