Some Laptops use a number of gpios to define which vendor is
used for a particular laptop.
Different coefficient files are used for different vendors.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220630002335.366545-9-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To be able to support different firmwares and tuning
for different models, the driver needs to be able to
load a different firmware and coefficient file based
on its Subsystem ID.
The driver attempts to load the firmware in the
following order:
/lib/firmware/cirrus/cs35l41-dsp1-<fw-type>-<ssid>-dev<#>.wmfw
/lib/firmware/cirrus/cs35l41-dsp1-<fw-type>-<ssid>.wmfw
/lib/firmware/cirrus/cs35l41-dsp1-<fw-type>.wmfw
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220630002335.366545-8-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some laptop models, the ACPI contains the unique
Subsystem ID, and this value should be preferred
over the value from the HDA driver.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220630002335.366545-7-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Subsystem ID is read from the HDA driver, and will
be used by the CS35L41 driver to be able to uniquely
identify the laptop, which is required to be able to
define firmware to be used by specific models.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220630002335.366545-6-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the CS35L41 DSP.
The DSP allows for extra features, such as running
speaker protection algorithms and hibernations.
To utilize these features, the driver must load
firmware into the DSP, as well as various tuning
files which allow for customization for specific
models.
[ Slightly simplified Kconfig changes by tiwai ]
Signed-off-by: Vitaly Rodionov <vitaly.rodionov@cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220630002335.366545-5-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
DSP controls are exposed as ALSA controls, however,
some of these controls are required to be accessed by
the driver. Add apis which allow read/write of these
controls. The write api will also notify the ALSA control
on value change.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220630002335.366545-3-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The cs35l41 part contains a DSP which is able to run firmware.
The cs_dsp library can be used to control the DSP.
These controls can be exposed to userspace using ALSA controls.
This library adds apis to be able to interface between
cs_dsp and hda drivers and expose the relevant controls as
ALSA controls.
[ Note: the dependency of CONFIG_SND_HDA_CS_DSP_CONTROLS Kconfig is
corrected. Also, this Kconfig isn't enabled now but will be
actually enabled in a later patch -- tiwai ]
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220630002335.366545-2-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use atomic_try_cmpxchg instead of atomic_cmpxchg (*ptr, old, new) == old in
ep_state_update. x86 CMPXCHG instruction returns success in ZF flag,
so this change saves a compare after cmpxchg (and related move instruction
in front of cmpxchg).
No functional change intended.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/r/20220713151946.4743-1-ubizjak@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Andrea Mayer says:
====================
seg6: fix skb checksum for SRH encapsulation/insertion
The Linux kernel supports Segment Routing Header (SRH)
encapsulation/insertion operations by providing the capability to: i)
encapsulate a packet in an outer IPv6 header with a specified SRH; ii)
insert a specified SRH directly after the IPv6 header of the packet.
Note that the insertion operation is also referred to as 'injection'.
The two operations are respectively supported by seg6_do_srh_encap() and
seg6_do_srh_inline(), which operate on the skb associated to the packet as
needed (e.g. adding the necessary headers and initializing them, while
taking care to recalculate the skb checksum).
seg6_do_srh_encap() and seg6_do_srh_inline() do not initialize the payload
length of the IPv6 header, which is carried out by the caller functions.
However, this approach causes the corruption of the skb checksum which
needs to be updated only after initialization of headers is completed
(thanks to Paolo Abeni for detecting this issue).
The patchset fixes the skb checksum corruption by moving the IPv6 header
payload length initialization from the callers of seg6_do_srh_encap() and
seg6_do_srh_inline() directly into these functions.
This patchset is organized as follows:
- patch 1/3, seg6: fix skb checksum evaluation in SRH
encapsulation/insertion;
(* SRH encapsulation/insertion available since v4.10)
- patch 2/3, seg6: fix skb checksum in SRv6 End.B6 and End.B6.Encaps
behaviors;
(* SRv6 End.B6 and End.B6.Encaps behaviors available since v4.14)
- patch 3/3, seg6: bpf: fix skb checksum in bpf_push_seg6_encap();
(* bpf IPv6 Segment Routing helpers available since v4.18)
====================
Link: https://lore.kernel.org/r/20220712175837.16267-1-andrea.mayer@uniroma2.it
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Both helper functions bpf_lwt_seg6_action() and bpf_lwt_push_encap() use
the bpf_push_seg6_encap() to encapsulate the packet in an IPv6 with Segment
Routing Header (SRH) or insert an SRH between the IPv6 header and the
payload.
To achieve this result, such helper functions rely on bpf_push_seg6_encap()
which, in turn, leverages seg6_do_srh_{encap,inline}() to perform the
required operation (i.e. encap/inline).
This patch removes the initialization of the IPv6 header payload length
from bpf_push_seg6_encap(), as it is now handled properly by
seg6_do_srh_{encap,inline}() to prevent corruption of the skb checksum.
Fixes: fe94cc290f ("bpf: Add IPv6 Segment Routing helpers")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The SRv6 End.B6 and End.B6.Encaps behaviors rely on functions
seg6_do_srh_{encap,inline}() to, respectively: i) encapsulate the
packet within an outer IPv6 header with the specified Segment Routing
Header (SRH); ii) insert the specified SRH directly after the IPv6
header of the packet.
This patch removes the initialization of the IPv6 header payload length
from the input_action_end_b6{_encap}() functions, as it is now handled
properly by seg6_do_srh_{encap,inline}() to avoid corruption of the skb
checksum.
Fixes: 140f04c33b ("ipv6: sr: implement several seg6local actions")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Support for SRH encapsulation and insertion was introduced with
commit 6c8702c60b ("ipv6: sr: add support for SRH encapsulation and
injection with lwtunnels"), through the seg6_do_srh_encap() and
seg6_do_srh_inline() functions, respectively.
The former encapsulates the packet in an outer IPv6 header along with
the SRH, while the latter inserts the SRH between the IPv6 header and
the payload. Then, the headers are initialized/updated according to the
operating mode (i.e., encap/inline).
Finally, the skb checksum is calculated to reflect the changes applied
to the headers.
The IPv6 payload length ('payload_len') is not initialized
within seg6_do_srh_{inline,encap}() but is deferred in seg6_do_srh(), i.e.
the caller of seg6_do_srh_{inline,encap}().
However, this operation invalidates the skb checksum, since the
'payload_len' is updated only after the checksum is evaluated.
To solve this issue, the initialization of the IPv6 payload length is
moved from seg6_do_srh() directly into the seg6_do_srh_{inline,encap}()
functions and before the skb checksum update takes place.
Fixes: 6c8702c60b ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/all/20220705190727.69d532417be7438b15404ee1@uniroma2.it
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
check_write_begin() will unlock and put the folio when return
non-zero. So we should avoid unlocking and putting it twice in
netfs layer.
Change the way ->check_write_begin() works in the following two ways:
(1) Pass it a pointer to the folio pointer, allowing it to unlock and put
the folio prior to doing the stuff it wants to do, provided it clears
the folio pointer.
(2) Change the return values such that 0 with folio pointer set means
continue, 0 with folio pointer cleared means re-get and all error
codes indicating an error (no special treatment for -EAGAIN).
[ bagasdotme: use Sphinx code text syntax for *foliop pointer ]
Cc: stable@vger.kernel.org
Link: https://tracker.ceph.com/issues/56423
Link: https://lore.kernel.org/r/cf169f43-8ee7-8697-25da-0204d1b4343e@redhat.com
Co-developed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Xiubo Li <xiubli@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
The 'pdev' and 'netdev' need to be released in error cases of
iss_net_configure().
Change the return type of iss_net_configure() to void, because it's
not used.
Fixes: 7282bee787 ("[PATCH] xtensa: Architecture support for Tensilica Xtensa Part 8")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Provide release() callback for the platform device embedded into struct
iss_net_private and registered in the iss_net_configure so that
platform_device_unregister could be called for it.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
There are two per-device lists in the ISS network driver: command line
parameters list and iss_net_private object list. The latter is only used
for duplicate checking in the function iss_net_setup where the former
should have been used.
Drop iss_net_private object list and associated code and use command
line parameters list in the iss_net_setup instead.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
UNTRAIN_RET is not needed in native_irq_return_ldt because RET
untraining has already been done at this point.
In addition, when the RETBleed mitigation is IBPB, UNTRAIN_RET clobbers
several registers (AX, CX, DX) so here it trashes user values which are
in these registers.
Signed-off-by: Alexandre Chartre <alexandre.chartre@oracle.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/35b0d50f-12d1-10c3-f5e8-d6c140486d4a@oracle.com
Return boolean values ("true" or "false") instead of 1 or 0 from bool
functions. This fixes the following warnings from coccicheck:
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:407:9-10: WARNING:
return of 0/1 in function 'decap_v4' with return type bool
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:389:9-10: WARNING:
return of 0/1 in function 'decap_v6' with return type bool
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:290:9-10: WARNING:
return of 0/1 in function 'encap_v6' with return type bool
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:264:9-10: WARNING:
return of 0/1 in function 'parse_tcp' with return type bool
tools/testing/selftests/bpf/progs/test_xdp_noinline.c:242:9-10: WARNING:
return of 0/1 in function 'parse_udp' with return type bool
Generated by: scripts/coccinelle/misc/boolreturn.cocci
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Linkui Xiao <xiaolinkui@kylinos.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Link: https://lore.kernel.org/bpf/20220714015647.25074-1-xiaolinkui@kylinos.cn
BPF map name is limited to BPF_OBJ_NAME_LEN.
A map name is defined as being longer than BPF_OBJ_NAME_LEN,
it will be truncated to BPF_OBJ_NAME_LEN when a userspace program
calls libbpf to create the map. A pinned map also generates a path
in the /sys. If the previous program wanted to reuse the map，
it can not get bpf_map by name, because the name of the map is only
partially the same as the name which get from pinned path.
The syscall information below show that map name "process_pinned_map"
is truncated to "process_pinned_".
bpf(BPF_OBJ_GET, {pathname="/sys/fs/bpf/process_pinned_map",
bpf_fd=0, file_flags=0}, 144) = -1 ENOENT (No such file or directory)
bpf(BPF_MAP_CREATE, {map_type=BPF_MAP_TYPE_HASH, key_size=4,
value_size=4,max_entries=1024, map_flags=0, inner_map_fd=0,
map_name="process_pinned_",map_ifindex=0, btf_fd=3, btf_key_type_id=6,
btf_value_type_id=10,btf_vmlinux_value_type_id=0}, 72) = 4
This patch check that if the name of pinned map are the same as the
actual name for the first (BPF_OBJ_NAME_LEN - 1),
bpf map still uses the name which is included in bpf object.
Fixes: 26736eb9a4 ("tools: libbpf: allow map reuse")
Signed-off-by: Anquan Wu <leiqi96@hotmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/OSZP286MB1725CEA1C95C5CB8E7CCC53FB8869@OSZP286MB1725.JPNP286.PROD.OUTLOOK.COM
The ARRAY_SIZE macro is more compact and more formal in linux source.
Signed-off-by: Linkui Xiao <xiaolinkui@kylinos.cn>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: https://lore.kernel.org/bpf/20220712072302.13761-1-xiaolinkui@kylinos.cn
Link: https://lore.kernel.org/r/165730608687.177165.11815510982277242966.stgit@brunhilda
Reviewed-by: Gerry Morong <gerry.morong@microchip.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update copyright to current year.
Link: https://lore.kernel.org/r/165730608177.177165.13184715486635363193.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow user to override the default driver timeout for controller ready.
There are some rare configurations which require the driver to wait longer
than the normal 3 minutes for the controller to complete its bootup
sequence and be ready to accept commands from the driver.
The module parameter is:
ctrl_ready_timeout= { 0 | 30-1800 }
and specifies the timeout in seconds for the driver to wait for controller
ready. The valid range is 0 or 30-1800. The default value is 0, which
causes the driver to use a timeout of 180 seconds (3 minutes).
Link: https://lore.kernel.org/r/165730607666.177165.9221211345284471213.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change removing a LUN using sysfs from an internal driver function
pqi_remove_all_scsi_devices() to using the .slave_destroy entry in the
scsi_host_template.
A LUN can be deleted via sysfs using this syntax:
echo 1 > /sys/block/sdX/device/delete
Link: https://lore.kernel.org/r/165730607154.177165.9723066932202995774.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow SMP affinity to be changeable by disabling managed interrupts.
On distributions where the driver is enabled for multi-queue support the
driver utilizes kernel managed interrupts, which automatically distributes
interrupts to all available CPUs and assigns SMP affinity.
On most distributions, the affinity can not be changed by the user.
This change will allow managed interrupts to be disabled by the user via a
module parameter while still allowing multi-queue support to function
properly.
Use the module parameter disable_managed_interrupts=1
Link: https://lore.kernel.org/r/165730606638.177165.12846020942931640329.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a rare stale RAID map access when performing AIO during a RAID
configuration change.
A race condition in the driver could cause it to access a stale RAID map
when a logical volume is reconfigured.
Modify the driver logic to invalidate a RAID map very early when a RAID
configuration change is detected and only switch to a new RAID map after
the driver detects that the RAID map has changed.
Link: https://lore.kernel.org/r/165730606128.177165.7671413443814750829.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Correct a SOP READ and WRITE DMA flags for some requests.
This update corrects DMA direction issues with SCSI commands removed from
the controller's internal lookup table.
Currently, SCSI READ BLOCK LIMITS (0x5) was removed from the controller
lookup table and exposed a DMA direction flag issue.
SCSI READ BLOCK LIMITS was recently removed from our controller lookup
table so the controller uses the respective IU flag field to set the DMA
data direction. Since the DMA direction is incorrect the FW never completes
the request causing a hang.
Some SCSI commands which use SCSI READ BLOCK LIMITS
* sg_map
* mt -f /dev/stX status
After updating controller firmware, users may notice their tape units
failing. This patch resolves the issue.
Also, the AIO path DMA direction is correct.
The DMA direction flag is a day-one bug with no reported BZ.
Fixes: 6c223761eb ("smartpqi: initial commit of Microsemi smartpqi driver")
Link: https://lore.kernel.org/r/165730605618.177165.9054223644512926624.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change method used to detect controller firmware crash during PQI reset.
PQI reset can fail with error -6 if firmware takes > 100ms to complete
reset.
Method used by driver to detect controller firmware crash during PQI was
incorrect in some cases.
Link: https://lore.kernel.org/r/165730605108.177165.1132931838384767071.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add the PCI ID for (values in hex):
VID / DID / SVID / SDID
---- ---- ---- ----
Adaptec SmartHBA 2100-8i-o 9005 / 0285 / 9005 / 0659
Link: https://lore.kernel.org/r/165730604089.177165.17257514581321583667.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fail all outstanding requests after a PCI linkdown.
Block access to device SCSI attributes during the following conditions:
"Cable pull" is called PQI_CTRL_SURPRISE_REMOVAL.
"PCIe Link Down" is called PQI_CTRL_GRACEFUL_REMOVAL.
Block access to device SCSI attributes during and in rare instances when
the controller goes offline.
Either outstanding requests or the access of SCSI attributes post linkdown
can lead to a hang.
Post linkdown, driver does not fail the outstanding requests leading to
long wait time before all the IOs eventually fail.
Also access of the SCSI attributes by host applications can lead to a
system hang.
Link: https://lore.kernel.org/r/165730603578.177165.4699352086827187263.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Sagar Biradar <sagar.biradar@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add driver support for up to 256 LUNs per device.
Update AIO path to pass the appropriate LUN number for base-code to target
the correct LUN.
Update RAID IO path to pass the appropriate LUN number for FW to target the
correct LUN.
Pass the correct LUN number while doing a LUN reset.
Count the outstanding commands based on LUN number. While removing a
Multi-LUN device, wait for all outstanding commands to complete for all
LUNs.
Add Feature bit support.
Link: https://lore.kernel.org/r/165730603067.177165.14016422176841798336.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Kumar Meiyappan <Kumar.Meiyappan@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Insert a minimum 1 millisecond delay after writing to a register before
reading from it.
SIS and PQI registers that can be both written to and read from can return
stale data if read from too soon after having been written to.
There is no read/write ordering or hazard detection on the inbound path to
the MSGU from the PCIe bus, therefore reads could pass writes.
Link: https://lore.kernel.org/r/165730602555.177165.11181012469428348394.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Signed-off-by: Mike McGowen <mike.mcgowen@microchip.com>
Co-developed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print controller firmware version to OS message log during driver
initialization or after OFA.
Link: https://lore.kernel.org/r/165730601536.177165.17698744242908911822.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Mike McGowen <mike.mcgowen@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Gilbert Wu <Gilbert.Wu@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Check the response code returned from the LUN reset task management
function and if it indicates the LUN is not valid, do not retry.
Reduce rescan worker delay to 5 seconds for the event handler only.
The removal of a drive from the OS could have been delayed up to 30 seconds
after being physically pulled.
The driver was retrying a LUN reset 3 times even though the return code
indiciated the LUN was no longer valid. There was a 10 second delay between
each retry. Additionally, the rescan worker was scheduled to run 10 seconds
after the driver received the event.
Link: https://lore.kernel.org/r/165730601025.177165.9416869335174437006.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microchip.com>
Signed-off-by: Mike McGowen <Mike.McGowen@microchip.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Negotiated link rate needs to be updated to 'Disabled' when phy is stopped.
Link: https://lore.kernel.org/r/20220708205026.969161-1-changyuanl@google.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, the data flow of the max/min linkrate in the driver is
* in pm8001_get_lrate_mode():
hardcoded value ==> struct sas_phy
* in pm8001_bytes_dmaed():
struct pm8001_phy ==> struct sas_phy
* in pm8001_phy_control():
libsas data ==> struct pm8001_phy
Since pm8001_bytes_dmaed() follows pm8001_get_lrate_mode(), and the fields
in struct pm8001_phy are not initialized, sysfs
`/sys/class/sas_phy/phy-*/maximum_linkrate` always shows `Unknown`.
To fix the issue, change the dataflow to the following:
* in pm8001_phy_init():
initial value ==> struct pm8001_phy
* in pm8001_get_lrate_mode():
struct pm8001_phy ==> struct sas_phy
* in pm8001_phy_control():
libsas data ==> struct pm8001_phy
For negotiated linkrate, the current dataflow is:
* in pm8001_get_lrate_mode():
iomb data ==> struct asd_sas_phy ==> struct sas_phy
* in pm8001_bytes_dmaed():
struct asd_sas_phy ==> struct sas_phy
Since pm8001_bytes_dmaed() follows pm8001_get_lrate_mode(), the assignment
statements in pm8001_bytes_dmaed() are unnecessary and cleaned up.
Link: https://lore.kernel.org/r/20220707175210.528858-1-changyuanl@google.com
Reviewed-by: Igor Pylypiv <ipylypiv@google.com>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Changyuan Lyu <changyuanl@google.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In ufshcd_host_reset_and_restore(), ufshcd_set_clk_freq() is called to
scale clock rate. However, this did not call vops->clk_scale_notify() to
inform platform driver of clock change.
Call ufshcd_scale_clks() instead so that clock change can be properly
handled.
Link: https://lore.kernel.org/r/20220711144224.17916-2-powen.kao@mediatek.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Po-Wen Kao <powen.kao@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit '3b5f3c0d05 ("scsi: ufs: core: Tidy up WB configuration code")'
changed the log level of the write boost enable/disable notification from
debug to info. This results in a lot of noise in the kernel log during
normal operation.
Drop it back to debug level to avoid this.
Link: https://lore.kernel.org/r/20220709000027.3929970-1-bjorn.andersson@linaro.org
Fixes: 3b5f3c0d05 ("scsi: ufs: core: Tidy up WB configuration code")
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Refactor code from fnic probe into a different function so that
scsi layer initialization code is grouped together.
Also, add log messages for better debugging.
Link: https://lore.kernel.org/r/20220707205155.692688-1-kartilak@cisco.com
Co-developed-by: Gian Carlo Boffa <gcboffa@cisco.com>
Signed-off-by: Gian Carlo Boffa <gcboffa@cisco.com>
Co-developed-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Arulprabhu Ponnusamy <arulponn@cisco.com>
Signed-off-by: Karan Tilak Kumar <kartilak@cisco.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set the maximum time firmware should poll for a link.
If not set firmware could block CPU for a long time resulting
in mailbox failures. If link doesn't come up within 1second,
firmware will anyway notify the status as and when LINK comes up
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20220712161815.12621-1-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-07-12
This series contains updates to ice driver only.
Paul fixes detection of E822 devices for firmware update and changes NVM
read for snapshot creation to be done in chunks as some systems cannot
read the entire NVM in the allotted time.
====================
Link: https://lore.kernel.org/r/20220712164829.7275-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 4db7a23605 ("scsi: ufs: Fix concurrency of error handler and other
error recovery paths") removed all callers of UIC_HIBERN8_ENTER_RETRIES.
Hence also remove the macro itself.
Link: https://lore.kernel.org/r/20220708052006epcms2p2d1129dbf95fd77f46906200ccb0a9ccd@epcms2p2
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Keoseong Park <keosung.park@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
