Treat the claimed 96kHz 1ch in the descriptors as 48kHz 2ch, so that
the audio stream doesn't sound mono. Also fix initial stream
alignment, so that left and right channels are in the correct order.
Signed-off-by: John Veness <john-linux@pelago.org.uk>
Link: https://lore.kernel.org/r/20220624140757.28758-1-john-linux@pelago.org.uk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'ret'.
This was found by coccicheck:
sound/soc/tegra/tegra20_ac97.c:357 tegra20_ac97_platform_probe() warn: missing error code 'ret'.
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220701072850.62408-1-jiapeng.chong@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Need to add legacy_dai_naming flag otherwise there
will be issue when registerring component, that cause
the probe failure.
Fixes: 1e63fcc74a ("ASoC: fsl: Migrate to new style legacy DAI naming flag")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1656899417-4775-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Need to add legacy_dai_naming flag otherwise there
will be issue when registerring component, that cause
the probe failure.
Fixes: 1e63fcc74a ("ASoC: fsl: Migrate to new style legacy DAI naming flag")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1656899417-4775-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The AMD acp-es8336 machine driver requires ES8316 run in producer
mode, which is not supported previously.
Signed-off-by: David Yang <yangxiaohua@everest-semi.com>
Signed-off-by: Zhu Ning <zhuning0077@gmail.com>
Link: https://lore.kernel.org/r/20220704012416.3165-1-zhuning0077@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the Synopsys DesignWare I2S controller binding to dt-schema.
There was no listed maintainer but Jose Abreu was the last editor of the
txt binding so add him as maintainer.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220701192300.2293643-4-conor@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We should call of_node_put() for the reference 'dsp_of_node' returned by
of_parse_phandle() which will increase the refcount.
Fixes: 9bae4880ac ("ASoC: qcom: move ipq806x specific bits out of lpass driver.")
Co-authored-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220702020109.263980-1-windhl@126.com
Signed-off-by: Mark Brown <broonie@kernel.org>
emulation_proc_handler() changes table->data for proc_dointvec_minmax
and can generate the following Oops if called concurrently with itself:
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
| Internal error: Oops: 96000006 [#1] SMP
| Call trace:
| update_insn_emulation_mode+0xc0/0x148
| emulation_proc_handler+0x64/0xb8
| proc_sys_call_handler+0x9c/0xf8
| proc_sys_write+0x18/0x20
| __vfs_write+0x20/0x48
| vfs_write+0xe4/0x1d0
| ksys_write+0x70/0xf8
| __arm64_sys_write+0x20/0x28
| el0_svc_common.constprop.0+0x7c/0x1c0
| el0_svc_handler+0x2c/0xa0
| el0_svc+0x8/0x200
To fix this issue, keep the table->data as &insn->current_mode and
use container_of() to retrieve the insn pointer. Another mutex is
used to protect against the current_mode update but not for retrieving
insn_emulation as table->data is no longer changing.
Co-developed-by: hewenliang <hewenliang4@huawei.com>
Signed-off-by: hewenliang <hewenliang4@huawei.com>
Signed-off-by: Haibin Zhang <haibinzhang@tencent.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220128090324.2727688-1-hewenliang4@huawei.com
Link: https://lore.kernel.org/r/9A004C03-250B-46C5-BF39-782D7551B00E@tencent.com
Signed-off-by: Will Deacon <will@kernel.org>
The platform device for the rng must be created much later in boot.
Otherwise it tries to connect to a parent that doesn't yet exist,
resulting in this splat:
[ 0.000478] kobject: '(null)' ((____ptrval____)): is not initialized, yet kobject_get() is being called.
[ 0.002925] [c000000002a0fb30] [c00000000073b0bc] kobject_get+0x8c/0x100 (unreliable)
[ 0.003071] [c000000002a0fba0] [c00000000087e464] device_add+0xf4/0xb00
[ 0.003194] [c000000002a0fc80] [c000000000a7f6e4] of_device_add+0x64/0x80
[ 0.003321] [c000000002a0fcb0] [c000000000a800d0] of_platform_device_create_pdata+0xd0/0x1b0
[ 0.003476] [c000000002a0fd00] [c00000000201fa44] pnv_get_random_long_early+0x240/0x2e4
[ 0.003623] [c000000002a0fe20] [c000000002060c38] random_init+0xc0/0x214
This patch fixes the issue by doing the platform device creation inside
of machine_subsys_initcall.
Fixes: f3eac42665 ("powerpc/powernv: wire up rng during setup_arch")
Cc: stable@vger.kernel.org
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
[mpe: Change "of node" to "platform device" in change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220630121654.1939181-1-Jason@zx2c4.com
Bypass power_on/power_off() when running on BCM2711 as they are not
needed.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-12-stefan.wahren@i2se.com
In BCM2711 the new RPiVid ASB took over V3D. The old ASB is still present
with the ISP and H264 bits, and V3D is in the same place in the new ASB
as the old one.
Use the fact that 'pm->rpivid_asb' is populated as a hint that we're on
BCM2711.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-11-stefan.wahren@i2se.com
The macros in order to access the ASB registers have a hard coded base
address. So extending them for other platforms would make them harder
to read. As a solution resolve these macros.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-10-stefan.wahren@i2se.com
The functions to control the async AXI bridges are almost identical.
So define a general function to handle it and keep the original ones as
wrapper. This should make this driver easier to extend.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-9-stefan.wahren@i2se.com
In mcp251xfd_register_get_dev_id() the device ID register is read with
handcrafted SPI transfers. As all registers, this register is in
little endian. Further it is not naturally aligned in struct
mcp251xfd_map_buf_nocrc::data. However after the transfer the register
content is converted from big endian to CPU endianness not taking care
of being unaligned.
Fix the conversion by converting from little endian to CPU endianness
taking the unaligned source into account.
Side note: So far the register content is 0x0 on all mcp251xfd
compatible chips, and is only used for an informative printk.
Link: https://lore.kernel.org/all/20220627092859.809042-1-mkl@pengutronix.de
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The device ID register is 32 bits wide. The driver uses incorrectly
the size of a pointer to a u32 to calculate the length of the SPI
transfer. This results in a read of 2 registers on 64 bit platforms.
This is no problem on the Linux side, as the RX buffer of the SPI
transfer is large enough. In the mpc251xfd chip this results in the
read of an undocumented register. So far no problems were observed.
Fix the length of the SPI transfer to read the device ID register
only.
Link: https://lore.kernel.org/all/20220616094914.244440-1-mkl@pengutronix.de
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit 169d00a256 ("can: mcp251xfd: add TX IRQ coalescing
support") software based TX coalescing was added to the driver. The
key idea is to keep the TX complete IRQ disabled for some time after
processing it and re-enable later by a hrtimer. When bringing the
interface down, this timer has to be stopped.
Add the missing hrtimer_cancel() of the tx_irq_time hrtimer to
mcp251xfd_stop().
Link: https://lore.kernel.org/all/20220620143942.891811-1-mkl@pengutronix.de
Fixes: 169d00a256 ("can: mcp251xfd: add TX IRQ coalescing support")
Cc: stable@vger.kernel.org # v5.18
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
New investigations and simulations indicate that the CRC send by the
device is calculated on correct data, and the data is incorrectly
received by the SPI host controller.
Use flipped instead of original data and update workaround description
in mcp251xfd_regmap_crc_read().
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The mcp251xfd compatible chips have an erratum ([1], [2]), where the
received CRC doesn't match the calculated CRC. In commit
c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work
around broken CRC on TBC register") the following workaround was
implementierend.
- If a CRC read error on the TBC register is detected and the first
byte is 0x00 or 0x80, the most significant bit of the first byte is
flipped and the CRC is calculated again.
- If the CRC now matches, the _original_ data is passed to the reader.
For now we assume transferred data was OK.
Measurements on the mcp2517fd show that the workaround is applicable
not only of the lowest byte is 0x00 or 0x80, but also if 3 least
significant bits are set.
Update check on 1st data byte and workaround description accordingly.
[1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands"
[2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands"
Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com
Fixes: c7eb923c3c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register")
Cc: stable@vger.kernel.org
Reported-by: Pavel Modilaynen <pavel.modilaynen@volvocars.com>
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
[mkl: split into 2 patches, update patch description and documentation]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use correct bittiming limits depending on device. For devices based on
USBcanII, Leaf M32C or Leaf i.MX28.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Fixes: b4f20130af ("can: kvaser_usb: add support for Kvaser Leaf v2 and usb mini PCIe")
Fixes: f5d4abea3c ("can: kvaser_usb: Add support for the USBcan-II family")
Link: https://lore.kernel.org/all/20220603083820.800246-4-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: remove stray netlink.h include]
[mkl: keep struct can_bittiming_const kvaser_usb_flexc_bittiming_const in kvaser_usb_hydra.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In BCM2711 the new RPiVid ASB took over V3D. The old ASB is still present
with the ISP and H264 bits, and V3D is in the same place in the new ASB
as the old one.
As per the devicetree bindings, BCM2711 will provide both the old and
new ASB resources, so get both of them and pass them into
'bcm2835-power,' which will take care of selecting which one to use
accordingly.
Since the RPiVid ASB's resources were being provided prior to formalizing
the bindings[1], also support the old DT files that didn't use
'reg-names.'
[1] See: 7dbe8c62ce ("ARM: dts: Add minimal Raspberry Pi 4 support")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-8-stefan.wahren@i2se.com
The firmware of M32C based Leaf devices expects bittiming parameters
calculated for 16MHz clock. Since we use the actual clock frequency of
the device, the device may end up with wrong bittiming parameters,
depending on user requested parameters.
This regression affects M32C based Leaf devices with non-16MHz clock.
Fixes: fb12797ab1 ("can: kvaser_usb: get CAN clock frequency from device")
Link: https://lore.kernel.org/all/20220603083820.800246-3-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If available in firmware, find resources by their 'reg-names' position
instead of relying on hardcoded offsets. Care is taken to support old
firmware nonetheless.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-7-stefan.wahren@i2se.com
Unify and move compile-time known information into new struct
kvaser_usb_driver_info, in favor of run-time checks.
All Kvaser USBcanII supports listen-only mode and error counter
reporting.
Link: https://lore.kernel.org/all/20220603083820.800246-2-extja@kvaser.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: move struct kvaser_usb_driver_info into kvaser_usb_core.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix spelling of 'waitting' in comments.
remove unnecessary space of 'MDIO_COMMAND_REG 's'.
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During a reset, there may have been transmits in flight that are no
longer valid and cannot be fulfilled. Resetting and clearing the
queues is insufficient; each skb also needs to be explicitly freed
so that upper levels are not left waiting for confirmation of a
transmit that will never happen. If this happens frequently enough,
the apparent backlog will cause TCP to begin "congestion control"
unnecessarily, culminating in permanently decreased throughput.
Fixes: d7c0ef36bd ("ibmvnic: Free and re-allocate scrqs when tx/rx scrqs change")
Tested-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Rick Lindsley <ricklind@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Horman says:
====================
nfp: support VLAN strip and insert
this series adds support to the NFP driver for HW offload of both:
* RX VLAN ctag/stag strip
* TX VLAN ctag insert
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TX VLAN ctag insert
which may be configured via ethtool.
e.g.
# ethtool -K $DEV tx-vlan-offload on
The NIC supplies VLAN insert information as packet metadata.
The fields of this VLAN metadata are gotten from sk_buff, including
vlan_proto and vlan tag.
Configuration control bit NFP_NET_CFG_CTRL_TXVLAN_V2 is to
signal availability of ctag-insert features of the firmware.
NFDK is used to communicate via PCIE to NFP-3800 based NICs
while NFD3 is used for other NICs supported by the NFP driver.
The metadata format on tx side of NFD3 is different from NFDK.
This feature is not currently implemented for NFDK.
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX VLAN ctag/stag strip
which may be configured via ethtool.
e.g.
# ethtool -K $DEV rx-vlan-offload on
# ethtool -K $DEV rx-vlan-stag-hw-parse on
Ctag-stripped and stag-stripped cannot be enabled at the same time
because currently the kernel supports only one layer of VLAN stripping.
The NIC supplies VLAN strip information as packet metadata.
The fields of this VLAN metadata are:
* strip flag: 1 for stripped; 0 for unstripped
* tci: VLAN TCI ID
* tpid: 1 for ETH_P_8021AD; 0 for ETH_P_8021Q
Configuration control bits NFP_NET_CFG_CTRL_RXVLAN_V2 and
NFP_NET_CFG_CTRL_RXQINQ are to signal availability of
ctag-strip and stag-strip features of the firmware.
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 1be37d3b04 ("can: m_can: fix periph RX path: use
rx-offload to ensure skbs are sent from softirq context") the RX path
for peripheral devices was switched to RX-offload.
Received CAN frames are pushed to RX-offload together with a
timestamp. RX-offload is designed to handle overflows of the timestamp
correctly, if 32 bit timestamps are provided.
The timestamps of m_can core are only 16 bits wide. So this patch
shifts them to full 32 bit before passing them to RX-offload.
Link: https://lore.kernel.org/all/20220612211410.4081390-1-mkl@pengutronix.de
Fixes: 1be37d3b04 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In commit df06fd6782 ("can: m_can: m_can_chip_config(): enable and
configure internal timestamps") the timestamping in the m_can core
should be enabled. In peripheral mode, the RX'ed CAN frames, TX
compete frames and error events are sorted by the timestamp.
The above mentioned commit however forgot to enable the timestamping.
Add the missing bits to enable the timestamp counter to the write of
the Timestamp Counter Configuration register.
Link: https://lore.kernel.org/all/20220612212708.4081756-1-mkl@pengutronix.de
Fixes: df06fd6782 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In grcan_probe(), of_find_node_by_path() has already increased the
refcount. There is no need to call of_node_get() again, so remove it.
Link: https://lore.kernel.org/all/20220619070257.4067022-1-windhl@126.com
Fixes: 1e93ed26ac ("can: grcan: grcan_probe(): fix broken system id check for errata workaround needs")
Cc: stable@vger.kernel.org # v5.18
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.
This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.
For more information, see the 928150fad4 ("can: esd_usb2: fix memory
leak").
Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
On R-Car V3U, this driver should use suitable register offset instead of
other SoCs' one. Otherwise, data transmission failed on R-Car V3U.
Fixes: 45721c406d ("can: rcar_canfd: Add support for r8a779a0 SoC")
Link: https://lore.kernel.org/all/20220704074611.957191-1-yoshihiro.shimoda.uh@renesas.com
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Lukas Wunner says:
====================
Deadlock no more in LAN95xx
Second attempt at fixing a runtime resume deadlock in the LAN95xx USB driver:
In short, the driver isn't using the "nopm" register accessors in portions
of its runtime resume path, causing a deadlock. I'm fixing that by
auto-detecting whether nopm accessors shall be used, instead of
having to explicitly call them wherever it's necessary.
As a byproduct, code size shrinks significantly (see diffstat below).
Back in April I submitted a first attempt which was rejected by Alan Stern:
https://lore.kernel.org/all/6710d8c18ff54139cdc538763ba544187c5a0cee.1651041411.git.lukas@wunner.de/
That approach only detected whether a PM callback is running concurrently,
not whether the access is performed by the PM callback. I've come up with
a different approach which should resolve the objection (see patch [1/3]).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
smsc95xx_read_reg() and smsc95xx_write_reg() call BUG_ON() if the
struct usbnet pointer passed in is NULL.
The functions have just been amended to dereference the pointer on
entry. So the kernel now oopses if the pointer is NULL, eliminating
the need for an explicit BUG_ON().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN95xx driver has just been amended to auto-detect whether the
_nopm variant of usbnet_read_cmd() / usbnet_write_cmd() shall be used.
Drop all the now unnecessary open coding of that distinction.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05b35e7eb9 ("smsc95xx: add phylib support") amended
smsc95xx_resume() to call phy_init_hw(). That function waits for the
device to runtime resume even though it is placed in the runtime resume
path, causing a deadlock.
The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(),
which never uses the _nopm variant of usbnet_read_cmd().
Commit b4df480f68 ("usbnet: smsc95xx: add reset_resume function with
reset operation") causes a similar deadlock on resume if the device was
already runtime suspended when entering system sleep:
That's because the commit introduced smsc95xx_reset_resume(), which
calls down to smsc95xx_reset(), which neglects to use _nopm accessors.
Fix by auto-detecting whether a device access is performed by the
suspend/resume task_struct and use the _nopm variant if so. This works
because the PM core guarantees that suspend/resume callbacks are run in
task context.
Stacktrace for posterity:
INFO: task kworker/2:1:49 blocked for more than 122 seconds.
Workqueue: usb_hub_wq hub_event
schedule
rpm_resume
__pm_runtime_resume
usb_autopm_get_interface
usbnet_read_cmd
__smsc95xx_read_reg
__smsc95xx_phy_wait_not_busy
__smsc95xx_mdio_read
smsc95xx_mdiobus_read
__mdiobus_read
mdiobus_read
smsc_phy_reset
phy_init_hw
smsc95xx_resume
usb_resume_interface
usb_resume_both
usb_runtime_resume
__rpm_callback
rpm_callback
rpm_resume
__pm_runtime_resume
usb_autoresume_device
hub_event
process_one_work
Fixes: b4df480f68 ("usbnet: smsc95xx: add reset_resume function with reset operation")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.16+
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for BCM53128 internal PHYs. These support interrupts as well as
statistics. Therefore, enable the Broadcom PHY driver for them.
Tested on BCM53128 switch using the mainline b53 DSA driver.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe the switch interrupts (dlr, switch, prp, hub, pattern) which
are connected to the GIC.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tests that permanent mdb entries can be added/deleted on ports with state down.
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strlcpy should not be used because it doesn't limit the source
length. Preferred is strscpy.
Signed-off-by: XueBing Chen <chenxuebing@jari.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 05ca14fdb6.
On early silicon engineering samples observed bit shrinking issue when
we use brp as 1. Hence updated brp_min as 2. As in production silicon
this issue is fixed, so reverting the patch.
Link: https://lore.kernel.org/all/20220609082433.1191060-2-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Jakub Kicinski says:
====================
docs: netdev: document more of our rules
The patch series length limit and reverse xmas tree are not documented.
Add those, and a tl;dr section summarizing how we differ.
v2: improve the series length blurb (Andrew)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Summarize the rules we see broken most often and which may
be less familiar to kernel devs who are used to working outside
of netdev.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to the 15 patch rule the reverse xmas tree is not
documented.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had been asking people to avoid massive patch series but it does
not appear in the FAQ.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
