'len' is decreased after each octet that has its EA bit set to 0, which
means that the value is encoded with additional octets. However, the final
octet does not decreases 'len' which results in 'len' being one byte too
long. A buffer over-read may occur in tty_insert_flip_string() as it tries
to read one byte more than the passed content size of 'data'.
Decrease 'len' also for the final octet which has the EA bit set to 1 to
write the correct number of bytes from the internal receive buffer to the
virtual tty.
Fixes: 2e124b4a39 ("TTY: switch tty_flip_buffer_push")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220504081733.3494-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XON1/XOFF1 character registers are at offset 0xa0 and 0xa8
respectively, so we cannot use the definition in serial_port.h.
Fixes: bdbd0a7f8f ("serial: 8250-mtk: modify baudrate setting")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220427132328.228297-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the FEATURE_SEL at probe time to make sure that BIT(0) is enabled:
this guarantees that when the port is configured as AP UART, the
right register layout is interpreted by the UART IP.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220427132328.228297-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On MediaTek SoCs, the UART IP is 16550A compatible, but there are some
specific quirks: we are declaring a register shift of 2, but this is
only valid for the majority of the registers, as there are some that
are out of the standard layout.
Specifically, this driver is using definitions from serial_reg.h, where
we have a UART_EFR register defined as 2: this results in a 0x8 offset,
but there we have the FCR register instead.
The right offset for the EFR register on MediaTek UART is at 0x98,
so, following the decimal definition convention in serial_reg.h and
accounting for the register left shift of two, add and use the correct
register address for this IP, defined as decimal 38, so that the final
calculation results in (0x26 << 2) = 0x98.
Fixes: bdbd0a7f8f ("serial: 8250-mtk: modify baudrate setting")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220427132328.228297-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: 5930cb3511 ("serial: driver for Conexant Digicolor USART")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220505124621.1592697-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fetch the average gfxclk according to pmfw for smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enable gfx ds for smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add the pg_flag for athub and mmhub pg.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add the pg_flag for athub and mmhub pg on smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
port the fan interface to smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add the sysfs pp_dpm_* interface for smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
port the SCPM change from smu_v13_0_0 to smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enable throttler, AC/DC, VR hot, FW CTF, fan control for smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Wang Yang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
enable link clock dpm and link clock deep sleep on smu_v13_0_7
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Jack Gui <Jack.Gui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set AMDGPU_FAMILY_GC_11_0_0.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Flora Cui <flora.cui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes are inherited from GC 11.0.0.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add initial support for GC 11.0.2 to gfx_v11_0.c.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Flora Cui <flora.cui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Define firmware for MES 11.0.2.
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Flora Cui <flora.cui@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is inherited from SDMA 6.0.0.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
