Deciding if to probe of PHYs using C45 is now determine by if the bus
provides the C45 read method. This makes probe_capabilities redundant
so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some PHYs provide invalid IDs in C22 space. If C45 is supported on the
bus an attempt can be made to get the IDs from the C45 space. Decide
on this based on the presence of the C45 read method in the bus
structure. This will allow the unreliable probe_capabilities to be
removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that all MDIO bus drivers which set probe_capabilities to
MDIOBUS_C22_C45 have been converted to use the name API for C45
transactions, perform the scanning of the bus based on which methods
the bus provides.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After scanning the bus for C22 devices, check if any Micrel PHYs have
been found. They are known to do bad things if there are C45
transactions on the bus. Prevent the scanning of the bus using C45 if
such a PHY has been detected.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some C22 PHYs do bad things when there are C45 transactions on the
bus. In order to handle this, the bus needs to be scanned first for
C22 at all addresses, and then C45 scanned for all addresses.
The Marvell pxa168 driver scans a specific address on the bus to find
its PHY. This is a C22 only device, so update it to use the c22
helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
No functional change, just place it earlier in preparation for some
refactoring.
While at it, correct the comment format and one typo.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a Device Feature List (DFL) bus driver for the Altera
16550 implementation of UART.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Marco Pagani <marpagan@redhat.com>
Link: https://lore.kernel.org/r/20230115151447.1353428-5-matthew.gerlach@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Version 1 of the Device Feature Header (DFH) definition adds
functionality to the Device Feature List (DFL) bus.
A DFHv1 header may have one or more parameter blocks that
further describes the HW to SW. Add support to the DFL bus
to parse the MSI-X parameter.
The location of a feature's register set is explicitly
described in DFHv1 and can be relative to the base of the DFHv1
or an absolute address. Parse the location and pass the information
to DFL driver.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230115151447.1353428-4-matthew.gerlach@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the definitions for DFHv1 header and related register
bitfields.
Signed-off-by: Basheer Ahmed Muddebihal <basheer.ahmed.muddebihal@linux.intel.com>
Co-developed-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230115151447.1353428-3-matthew.gerlach@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add documentation describing the extensions provided by Version
1 of the Device Feature Header (DFHv1).
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230115151447.1353428-2-matthew.gerlach@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use active consistently for naming parameters and variables.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-13-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert various parameter names for ->dtr_rts() and related functions
from onoff, on, and raise to active.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-12-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert uart_handle_cts_change() to bool which is more appropriate
than unsigned int.
Rename status to active to better describe what the parameter means.
While at it, make the comment about the active parameter easier to
parse.
Cleanup callsites from operations that are not necessary with bool.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-10-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert status parameter for ->dcd_change() and
uart_handle_dcd_change() to bool which matches to how the parameter is
used.
Rename status to active to better describe what the parameter means.
Acked-by: Rodolfo Giometti <giometti@enneenne.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-9-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the raise/on parameter in ->dtr_rts() to bool through the
callchain. The parameter is used like bool. In USB serial, there
remains a few implicit bool -> larger type conversions because some
devices use u8 in their control messages.
In moxa_tiocmget(), dtr variable was reused for line status which
requires int so use a separate variable for status.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-8-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return boolean from ->carrier_raised() instead of 0 and 1. Make the
return type change also to tty_port_carrier_raised() that makes the
->carrier_raised() call (+ cd variable in moxa into which its return
value is stored).
Also cleans up a few unnecessary constructs related to this change:
return xx ? 1 : 0;
-> return xx;
if (xx)
return 1;
return 0;
-> return xx;
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert init_hw parameter in uart_startup() and uart_port_startup() to
bool as code treats them like bool.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return type of tty_port_initialized() is bool, use matching type for
the local variable.
Also reorder the local vars to reverse-xmas-tree while at it.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230117090358.4796-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the devm_clk_get() may return ERR_PTR, its return value needs to be
checked to avoid invalid poineter dereference.
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221125093832.33386-1-yuancan@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios"
this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user
space. Controlled by this GPIO, now the hardware is responsible for connecting
or disconnecting RX during TX.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-4-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a RX_DURING_TX GPIO is defined by the DT property "rs485-rx-during-tx-gpios"
this patch switches this GPIO accordingly to the RS485 flag RX_DURING_TX in user
space. In addition, the i.MX UART receiver is no longer turned on and off during
sending, because now the hardware is responsible for connecting or disconnecting
RX during TX controlled by this GPIO.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-3-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides a generic GPIO variable for outputting the state
of RS485 RX_DURING_TX. The GPIO is defined by the devicetree property
"rs485-rx-during-tx-gpios". To use it in a low level serial driver,
the evaluation of this variable must be implemented there accordingly.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Link: https://lore.kernel.org/r/20221202104127.122761-2-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a binding for a generic definition of an output GPIO that sets the
state of rs485-rx-during-tx. The idea is that the hardware already controls
the option receiving during sending before it gets to the signal receiving
hardware. The standard RS485 is a half-duplex bus that in most cases is
driven by an UART controller. The advantage of using this GPIO is that it
is independent of the capabilities of the UART core and the UART driver.
On the hardware side the interface to the bus is controlled by a transceiver,
that has a pin called RE (RX Enable) or similar, which connects the bus to
the RX signal of the UART controller. The GPIO can switch between two states
to control the RE pin via an electrical circuit:
- Active:
The RE pin is always active. The UART RX see everything on the bus and
therefore also what happens with the TX signal on the bus.
- Inactive:
The RE pin is always active, but during sending on the bus the pin RE is
inactive. So basically the receiving during sending is suppressed.
A possible circuit diagram could look like this:
┌──────────────────┐
│ RS485 │
TX ───────────────┤D │
│ Transceiver │
RTS ────┬──────────┤DE │
│ │ │
│ ┌─────┐ │ │
└─┤& │ │ │
│ ├──┤!RE │
!rx_during_tx_gpio ──────┤ │ │ │
└─────┘ │ │
│ │
RX ───────────────┤R │
│ │
└──────────────────┘
Here the RTS pin of the UART core is used to control TX via the transceiver
pin DE (Drive Enable). RE and rx_during_tx_gpio are active low.
Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221202104127.122761-1-cniedermaier@dh-electronics.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing clk_disable_unprepare() before return from
tegra_uart_hw_init() in the error handling path.
When request_irq() fails in tegra_uart_startup(), 'tup->uart_clk'
has been enabled, fix it by adding clk_disable_unprepare().
Fixes: cc9ca4d958 ("serial: tegra: Only print FIFO error message when an error occurs")
Fixes: d781ec21ba ("serial: tegra: report clk rate errors")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20221126020852.113378-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order.
Co-developed-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Wen-chien Jesse Sung <jesse.sung@canonical.com>
Signed-off-by: Isaac True <isaac.true@canonical.com>
Link: https://lore.kernel.org/r/20221130105529.698385-1-isaac.true@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ucc_uart_probe(), we have added proper of_node_put() in the failure
paths. However, we miss it before we free *qe_port* in the remove() function.
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20221205085437.1163682-1-windhl@126.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmPHp2QACgkQSD+KveBX
+j6M/QgAoyMrhYAKC8xiD/yYMvzpQUbl1iMZpK+YhTMMbYCnnsNZSNHLpq2CRu/B
hqNCBvMOgZD37413UcyskpLuPSNUTQPQthKxui1R3BQyCMjvw3Qoso3ALGkxGh+M
OIak6FPx6Mh198FXGFFjK5kvmlrN4Z+A9vdIVP725M27JqhX4czOJDBVXBukV4+L
yxmRxVk926iMNUs4j4+iVlFbAssUEqQVbjg+eEZUkb60mgKLXK9lTE3+5ngybeZm
qjluUa7mukUMcR1fmR6jAiuHQSkn3xWHbS1ztTm14PTkpomn5JQ/mSqY6jxVfl1u
1AGNmx2k+Cca2z8/5MndhVafLOSe6g==
=tzWU
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2023-01-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-01-18' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net: mlx5: eliminate anonymous module_init & module_exit
net/mlx5: E-switch, Fix switchdev mode after devlink reload
net/mlx5e: Protect global IPsec ASO
net/mlx5e: Remove optimization which prevented update of ESN state
net/mlx5e: Set decap action based on attr for sample
net/mlx5e: QoS, Fix wrongfully setting parent_element_id on MODIFY_SCHEDULING_ELEMENT
net/mlx5: E-switch, Fix setting of reserved fields on MODIFY_SCHEDULING_ELEMENT
net/mlx5e: Remove redundant xsk pointer check in mlx5e_mpwrq_validate_xsk
net/mlx5e: Avoid false lock dependency warning on tc_ht even more
net/mlx5: fix missing mutex_unlock in mlx5_fw_fatal_reporter_err_work()
====================
Link: https://lore.kernel.org/r/
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix the following warning:
panel-visionox-vtdr6130.c:249:12: warning: 'ret' is used uninitialized [-Wuninitialized]
Fixes: 9402cde934 ("drm/panel: vtdr6130: Use 16-bit brightness function")
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230119-topic-sm8550-vtdr6130-fixup-v1-1-82c4fb008138@linaro.org
The qcom-geni-serial driver currently only works in SE FIFO mode. This
limits the UART speed to around 180 kB/s. In order to achieve higher
speeds we need to use SE DMA mode.
Keep the console port working in FIFO mode but extend the code to use DMA
for the high-speed port.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-15-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following symbols will be used when adding support for SE DMA in
the qcom geni serial driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-14-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of checking the device compatible in probe(), assign the
device-specific data to struct of_device_id. We'll use it later when
providing SE DMA support.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-13-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value of the handle_rx() callback is never checked. Drop it.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-12-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuffle the code a bit, drop unneeded variables, make types of others
more consistent and use uart_xmit_advance() instead of handling
tail->xmit manually.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-11-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
qcom_geni_serial_handle_tx() is pretty big, let's move the code that
handles the actual writing of data to a separate function which makes
sense in preparation for introducing a dma variant of handle_tx().
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-10-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove stray newlines around #ifdefs for consistency with the rest
of the driver code.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-7-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The member we want to resolve in struct qcom_geni_serial_port is called
uport so we don't need an additional redundant parameter in this macro.
While at it: turn the macro into a static inline function.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-6-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop all unused symbols from the driver.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-4-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we shuffle the code a bit, we can drop all forward definitions of
various static functions.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-3-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't stop transmissions in progress at shutdown. This is fine with
FIFO SE mode but with DMA (support for which we'll introduce later) it
causes trouble so fix it now.
Fixes: e83766334f ("tty: serial: qcom_geni_serial: No need to stop tx/rx on UART shutdown")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20221229155030.418800-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's used on few places, so make the code easier to follow by caching
the subtraction result.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230112080136.4929-11-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
