"make dtbs_check":
Documentation/devicetree/bindings/dma/snps,dw-axi-dmac.yaml
arch/riscv/boot/dts/canaan/sipeed_maix_bit.dt.yaml: dma-controller@50000000: 'resets' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/dma/snps,dw-axi-dmac.yaml
The Synopsys DesignWare AXI DMA Controller on the Canaan K210 SoC
exposes its reset signal.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20211125152008.162571-1-geert@linux-m68k.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For some devices with only half-duplex capabilities, it doesn't make
much sense to use one DMA channel per direction, as both channels will
never be active at the same time.
Add support for bidirectional I/O on DMA channels. The client drivers
can then request a "tx-rx" DMA channel which will be used for both
directions.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211206174259.68133-7-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4760 and JZ4760B SoCs have two regular DMA controllers with 6
channels each. They also have an extra DMA controller named MDMA
with only 2 channels, that only supports memcpy operations, and one
named BDMA with only 3 channels, that is mostly used for transfers
between memories and the BCH controller.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211206174259.68133-5-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4760 SoC has a hardware problem with chan0 not enabling properly
if it's enabled before chan1, after a reset (works fine afterwards).
This is worked around in the probe function by just enabling then
disabling chan1.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20211206174259.68133-4-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The JZ4760 and JZ4760B SoCs have two additional DMA controllers: the
MDMA, which only supports memcpy operations, and the BDMA which is
mostly used for transfer between memories and the BCH controller.
The JZ4770 also features the same BDMA as in the JZ4760B, but does not
seem to have a MDMA.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211206174259.68133-2-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The TI k3-bcdma and k3-pktdma both use 'ti,sci' and 'ti,sci-dev-id'
properties defined in ti,k3-sci-common.yaml. When 'unevaluatedProperties'
support is enabled, the follow warning is generated:
Documentation/devicetree/bindings/dma/ti/k3-bcdma.example.dt.yaml: dma-controller@485c0100: Unevaluated properties are not allowed ('ti,sci', 'ti,sci-dev-id' were unexpected)
Documentation/devicetree/bindings/dma/ti/k3-pktdma.example.dt.yaml: dma-controller@485c0000: Unevaluated properties are not allowed ('ti,sci', 'ti,sci-dev-id' were unexpected)
Add a reference to ti,k3-sci-common.yaml to fix this.
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211206174226.2298135-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With 'unevaluatedProperties' support implemented, the example has
warnings on primecell properties and 'resets':
Documentation/devicetree/bindings/dma/arm-pl08x.example.dt.yaml: dma-controller@67000000: Unevaluated properties are not allowed ('arm,primecell-periphid', 'resets' were unexpected)
Add the missing reference to primecell.yaml and definition for 'resets'.
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20211206174231.2298349-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add SYSFW defined rchan_oes_offset number for J721S2 SoC in soc data.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20211119132315.15901-2-a-govindraju@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Make use of the struct_size() helper instead of an open-coded version, in
order to avoid any potential type mistakes or integer overflows that, in
the worst scenario, could lead to heap overflows.
Link: https://github.com/KSPP/linux/issues/160
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20211208001013.GA62330@embeddedor
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Handle errors when trying to map the IRQ for the DMA channels.
The main motivation here is to be able to handle probe deferral. E.g. when
using DT overlays it is possible that the DMA controller is probed before
interrupt controller, depending on the order in the DT.
In order to support this switch from irq_of_parse_and_map() to
of_irq_get(), which internally does the same, but it will return
EPROBE_DEFER when the interrupt controller is not yet available.
As a result other errors, such as an invalid IRQ specification, or missing
IRQ are also properly handled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/20211208114212.234130-1-lars@metafoo.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The USB2.0 spec chapter 11.24.2.13 says that the USB port which is going
under test needs to be put in suspend state before sending the test
command. Many hubs, don't enforce this precondition and they work fine
without this step. We should follow the specification and put the USB
port in suspend before sending the test command.
Also there are some "special" hubs, which requires to disable the USB
port power instead of putting it in suspend. I found out only three hubs
which requires this step, but if more are found, they can be added to
the list.
Since this changes the default implementation, it raises the posibility
of finding other broken hubs which are not compliant with the spec and
the test command might not work is the port is suspended. If such hubs
are found, a similar workaround like the disable part can be implemented
to skip putting the port in suspend.
Signed-off-by: Razvan Heghedus <heghedus.razvan@gmail.com>
Link: https://lore.kernel.org/r/20211213183617.14156-2-heghedus.razvan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Export usb_device_match_id so that it can be used for easily matching an
usb_device with a table of IDs.
Signed-off-by: Razvan Heghedus <heghedus.razvan@gmail.com>
Link: https://lore.kernel.org/r/20211213183617.14156-1-heghedus.razvan@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb glue drivers just copy the glue resources to the musb child device.
Instead, set the musb child device's DT node pointer to the parent device's
node so that platform_get_irq_byname() can find the resources in the DT.
This removes the need for statically populating the IRQ resources from the
DT which has been deprecated for some time.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215230756.2009115-3-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform device resources are copied by the driver core, so there is
no need for the caller to do it when creating a platform device. Just pass
the parent resources to the child device directly.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215230756.2009115-2-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO for some strange reason. Switch to propagating the error codes
upstream.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20211214204247.7172-5-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver overrides the error codes and IRQ0 returned by platform_get_irq()
to -ENODEV. Switch to propagating the error codes upstream. IRQ0 is no
longer returned by platform_get_irq(), so we now can safely ignore it...
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20211214204247.7172-4-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV for some strange reason. Switch to propagating the error codes
upstream.
Acked-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20211214204247.7172-3-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENXIO for some strange reason. Switch to propagating the error codes
upstream.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20211214204247.7172-2-s.shtylyov@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Override enable bits may not be restored when going to low power mode
(e.g. when in DWC2_POWER_DOWN_PARAM_NONE).
These bits are set when probing/initializing drd (role switch). Restore
them upon resume from low power mode (in case these have been lost).
To achieve this, the last known role is restored upon resume. And the
override enable bits are always set when configuring aval, bval and vbval.
When resuming, forcing the role should be done only once, or this can cause
port changes in HOST mode for instance.
So, only restore FORCEDEVMODE/FORCEHOSTMODE when role_sw is unused
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1638806203-6624-4-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using usb-role-switch, while the usb role is not yet define
(USB_ROLE_NONE), the user may want to configure the default mode to host
or device.
Use role-switch-default-mode for that purpose.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1638806203-6624-3-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
role-switch-default-mode property may be used with usb-role-switch
property to define the default operation mode (by forcing the a-valid or
b-valid) at init.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1638806203-6624-2-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ChipIdea glue drivers just copy the glue resources to the "ci_hdrc"
child device. Instead, set the child device's DT node pointer to the
parent device's node so that platform_get_irq() can find the IRQ
resources in the DT. This removes the need for statically populating the
IRQ resources from the DT which has been deprecated for some time.
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215225646.1997946-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing platform device resources directly has long been deprecated for
DT as IRQ resources may not be available at device creation time. Drivers
continuing to use static IRQ resources is blocking removing the static setup
from the DT core code.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215225203.1991003-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing platform device resources directly has long been deprecated for
DT as IRQ resources may not be available at device creation time. Drivers
relying on the static IRQ resources is blocking removing the static setup
from the DT core code.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215225358.1993774-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The memory resource is already retrieved with platform_get_resource(), so
let's use it instead of assuming it is the first resource in the array.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211215225509.1995417-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the compatible string for USB controller for Qualcomm SM8450 SoC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211216113849.659856-1-vkoul@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The min and max frequency QoS requests in the cpufreq core are
initialized to whatever the current min and max frequency values are
at the init time, but if any of these values change later (for
example, cpuinfo.max_freq is updated by the driver), these initial
request values will be limiting the CPU frequency unnecessarily
unless they are changed by user space via sysfs.
To address this, initialize min_freq_req and max_freq_req to
FREQ_QOS_MIN_DEFAULT_VALUE and FREQ_QOS_MAX_DEFAULT_VALUE,
respectively, so they don't really limit anything until user
space updates them.
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is an expectation from users that they can get frequency specified
by cpufreq/cpuinfo_max_freq when conditions permit. But with AlderLake
mobile it may not be possible. This is possible that frequency is clipped
based on the system power-up EPP value. In this case users can update
cpufreq/energy_performance_preference to some performance oriented EPP to
limit clipping of frequencies.
To get out of box behavior as the prior generations of CPUs, update EPP
for AlderLake mobile CPUs on boot. On prior generations of CPUs EPP = 128
was enough to get maximum frequency, but with AlderLake mobile the
equivalent EPP is 102. Since EPP is model specific, this is possible that
they have different meaning on each generation of CPU.
The current EPP string "balance_performance" corresponds to EPP = 128.
Change the EPP corresponding to "balance_performance" to 102 for only
AlderLake mobile CPUs and update this on each CPU during boot.
To implement reuse epp_values[] array and update the modified EPP at the
index for BALANCE_PERFORMANCE. Add a dummy EPP_INDEX_DEFAULT to
epp_values[] to match indexes in the energy_perf_strings[].
After HWP PM is enabled also update EPP when "balance_performance" is
redefined for the very first time after the boot on each CPU. On
subsequent suspend/resume or offline/online the old EPP is restored,
so no specific action is needed.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
vmw_user_bo_lookup can fail to lookup user buffers, especially because
the buffer handles come from the userspace. The return value has
to be checked before the buffers are put back.
This was spotted by Dan's Smatch statick checker:
drivers/gpu/drm/vmwgfx/vmwgfx_bo.c:574 vmw_user_bo_synccpu_release()
error: uninitialized symbol 'vmw_bo'.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 8afa13a058 ("drm/vmwgfx: Implement DRIVER_GEM")
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215200224.3693345-1-zack@kde.org
(cherry picked from commit 60c9ecd705)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Before the driver had screen targets support we had to disable explicit
bringup of its infrastructure because it was breaking screen objects
support.
Since the implementation of screen targets landed there hasn't been a
reason to explicitly disable it and the options were never used.
Remove of all that unused code.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: d80efd5cb3 ("drm/vmwgfx: Initial DX support")
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215184147.3688785-3-zack@kde.org
(cherry picked from commit 11343099d5)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Old versions of the svga device used to export virtual vram, handling of
which was optimized on top of transparent hugepages support. Only very
old devices (OpenGL 2.1 support and earlier) used this code and at this
point performance differences are negligible.
Because the code requires very old hardware versions to run it has
been largely untested and unused for a long time.
Furthermore removal of the ttm hugepages support in:
commit 0d97950953 ("drm/ttm: remove ttm_bo_vm_insert_huge()")
broke the coherency mode in vmwgfx when running with hugepages.
Fixes: 0d97950953 ("drm/ttm: remove ttm_bo_vm_insert_huge()")
Signed-off-by: Zack Rusin <zackr@vmware.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215184147.3688785-2-zack@kde.org
(cherry picked from commit 49d535d64d)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
On i386 size_t is of course 32bits and using long int throws warnings,
trivially fix it by using the dedicated size_t format.
This is enough to fix the following warning found by the kernel test
robot:
drivers/gpu/drm/vmwgfx/vmwgfx_gem.c: In function 'vmw_bo_print_info':
>> drivers/gpu/drm/vmwgfx/vmwgfx_gem.c:230:33: warning: format '%ld'
expects argument of type 'long int', but argument 4 has type 'size_t'
{aka 'unsigned int'} [-Wformat=]
230 | seq_printf(m, "\t\t0x%08x: %12ld bytes %s, type = %s",
| ~~~~^
| |
| long int
| %12d
231 | id, bo->base.base.size, placement, type);
| ~~~~~~~~~~~~~~~~~~
| |
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Fixes: 8afa13a058 ("drm/vmwgfx: Implement DRIVER_GEM")
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Maaz Mombasawala <mombasawalam@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211215184147.3688785-1-zack@kde.org
(cherry picked from commit 72345114c9)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Drop superfluous "the" from the comment in line 15.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
[ rjw: Subject edit, new changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmG8i3cRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZumyAf7BlhO1TUuwhhs9y6fi6KLa/pEOmkx2SRf
9AuEfxxrLPhlzh29Dz4Bn8B+KBG6HFQ1FngSwIAVjLL5pX/1ARBMx9B2TDf9p/Sb
UgkE6WOX29s7LXuC2lDnBnvnKbf5/rdLmZPZCFCv/iKaGAJAYYXYSQjtj5/Fmdkc
PhQNgALWG9a02bfSLk1MlF1lCqt0hsKFQkza29jTa9CKcWYZFK3sTl1spbHAN5yQ
YJMecy+fSxCSuJPZB3elG5os69sz3WGoFY/AYCWoUODNZo18Z4kiAXwurPDIM+GW
3e/lzXe29V1TB36haNe9/C5F2uwoYWGSoWwHcZ62lLpNhJ649wJDbw==
=4wFO
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.17
Second set of patches for v5.17, planning to do at least one more.
Smaller new features, nothing special this time.
Major changes:
rtw88
* debugfs file to fix tx rate
iwlwifi
* support SAR GEO Offset Mapping (SGOM) via BIOS
* support firmware API version 68
* add some new device IDs
ath11k
* support PCI devices with 1 MSI vector
* WCN6855 hw2.1 support
* 11d scan offload support
* full monitor mode, only supported on QCN9074
* scan MAC address randomization support
* reserved host DDR addresses from DT for PCI devices support
ath9k
* switch to rate table based lookup
ath
* extend South Korea regulatory domain support
wcn36xx
* beacon filter support
* tag 'wireless-drivers-next-2021-12-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (129 commits)
wcn36xx: Implement beacon filtering
wcn36xx: Fix physical location of beacon filter comment
wcn36xx: Fix beacon filter structure definitions
ath11k: Use reserved host DDR addresses from DT for PCI devices
dt: bindings: add new DT entry for ath11k PCI device support
wilc1000: Improve WILC TX performance when power_save is off
wl1251: specify max. IE length
rsi: fix array out of bound
wilc1000: Rename workqueue from "WILC_wq" to "NETDEV-wq"
wilc1000: Rename tx task from "K_TXQ_TASK" to NETDEV-tx
wilc1000: Rename irq handler from "WILC_IRQ" to netdev name
wilc1000: Rename SPI driver from "WILC_SPI" to "wilc1000_spi"
wilc1000: Fix spurious "FW not responding" error
wilc1000: Remove misleading USE_SPI_DMA macro
wilc1000: Fix missing newline in error message
wilc1000: Fix copy-and-paste typo in wilc_set_mac_address
rtw89: coex: Update COEX to 5.5.8
rtw89: coex: Cancel PS leaving while C2H comes
rtw89: coex: Update BT counters while receiving report
rtw89: coex: Define LPS state for BTC using
...
====================
Link: https://lore.kernel.org/r/20211217130952.34887C36AE9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 796eed4b23.
This change causes boot lockups when using "arlyprintk=xdbc" because
ktime can not be used at this point in time in the boot process. Also,
it is not needed for very small delays like this.
Reported-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reported-by: Peter Zijlstra <peterz@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Fixes: 796eed4b23 ("usb: early: convert to readl_poll_timeout_atomic()")
Link: https://lore.kernel.org/r/c2b5c9bb-1b75-bf56-3754-b5b18812d65e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not necessary to call intel_pstate_get_hwp_cap() from
intel_pstate_update_perf_limits(), because it gets called from
intel_pstate_verify_cpu_policy() which is either invoked directly
right before intel_pstate_update_perf_limits(), in
intel_cpufreq_verify_policy() in the passive mode, or called
from driver callbacks in a sequence that causes it to be followed
by an immediate intel_pstate_update_perf_limits().
Namely, in the active mode intel_cpufreq_verify_policy() is called
by intel_pstate_verify_policy() which is the ->verify() callback
routine of intel_pstate and gets called by the cpufreq core right
before intel_pstate_set_policy(), which is the driver's ->setoplicy()
callback routine, where intel_pstate_update_perf_limits() is called.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because refcount_dec_not_one() returns true if the target refcount
becomes saturated, it is generally unsafe to use its return value as
a loop termination condition, but that is what happens when a device
link's supplier device is released during runtime PM suspend
operations and on device link removal.
To address this, introduce pm_runtime_release_supplier() to be used
in the above cases which will check the supplier device's runtime
PM usage counter in addition to the refcount_dec_not_one() return
value, so the loop can be terminated in case the rpm_active refcount
value becomes invalid, and update the code in question to use it as
appropriate.
This change is not expected to have any visible functional impact.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Fix function name in sysfs.c kernel-doc comment
to remove a warning found by running scripts/kernel-doc,
which is caused by using 'make W=1'.
drivers/cpuidle/sysfs.c:512: warning: expecting prototype for
cpuidle_remove_driver_sysfs(). Prototype was for
cpuidle_remove_state_sysfs() instead
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In some cases (for example, during system-wide suspend and resume of
devices) it is useful to know whether or not runtime PM has ever been
enabled for a given device and, if so, what the runtime PM status of
it had been right before runtime PM was disabled for it last time.
For this reason, introduce a new struct dev_pm_info field called
last_status that will be used for capturing the runtime PM status of
the device when its power.disable_depth counter changes from 0 to 1.
The new field will be set to RPM_INVALID to start with and whenever
power.disable_depth changes from 1 to 0, so it will be valid only
when runtime PM of the device is currently disabled, but it has been
enabled at least once.
Immediately use power.last_status in rpm_resume() to make it handle
the case when PM runtime is disabled for the device, but its runtime
PM status is RPM_ACTIVE more consistently. Namely, make it return 1
if power.last_status is also equal to RPM_ACTIVE in that case (the
idea being that if the status was RPM_ACTIVE last time when
power.disable_depth was changing from 0 to 1 and it is still
RPM_ACTIVE, it can be assumed to reflect what happened to the device
last time when it was using runtime PM) and -EACCES otherwise.
Update the documentation to provide a description of last_status and
change the description of pm_runtime_resume() in it to reflect the
new behavior of rpm_active().
While at it, rearrange the code in pm_runtime_enable() to be more
straightforward and replace the WARN() macro in it with a pr_warn()
invocation which is less disruptive.
Link: https://lore.kernel.org/linux-pm/20211026222626.39222-1-ulf.hansson@linaro.org/t/#u
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On Sapphire Rapids, the layout of the Psys domain Power Limit Register
is different from from what it was before.
Enhance the code to support the new Psys PL register layout.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Reported-and-tested-by: Alkattan Dana <dana.alkattan@intel.com>
[ rjw: Subject and changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Enable support for the new R-Car S4-8 SoC in the arm64 defconfig.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYbxfrQAKCRCKwlD9ZEnx
cN4JAP9GUQoB0x+Cw30qvh+Hp/U3UdcbtK9dNPElNp9r0vx9CAEA76Uy6+Byspee
RBPpKQDK7gWr8LrioHFLOTROLeTbnQw=
=0D6v
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=X44H
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm-defconfig-for-v5.17-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/defconfig
Renesas ARM defconfig updates for v5.17
- Enable support for the new R-Car S4-8 SoC in the arm64 defconfig.
* tag 'renesas-arm-defconfig-for-v5.17-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: defconfig: Enable R-Car S4-8
Link: https://lore.kernel.org/r/cover.1639736717.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
