No point in building unused code when CONFIG_SYSFS=n.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20211206210223.985907940@linutronix.de
pci_irq_vector() and pci_irq_get_affinity() use the list position to find the
MSI-X descriptor at a given index. That's correct for the normal case where
the entry number is the same as the list position.
But it's wrong for cases where MSI-X was allocated with an entries array
describing sparse entry numbers into the hardware message descriptor
table. That's inconsistent at best.
Make it always check the entry number because that's what the zero base
index really means. This change won't break existing users which use a
sparse entries array for allocation because these users retrieve the Linux
interrupt number from the entries array after allocation and none of them
uses pci_irq_vector() or pci_irq_get_affinity().
Fixes: aff171641d ("PCI: Provide sensible IRQ vector alloc/free routines")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20211206210223.929792157@linutronix.de
Finish the work by removing all references to the PPC4xx_MSI config
and the associated device nodes in the DTs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/e92f2bb3-b5e1-c870-8151-3917a789a640@kaod.org
This code is broken since day one. ppc4xx_setup_msi_irqs() has the
following gems:
1) The handling of the result of msi_bitmap_alloc_hwirqs() is completely
broken:
When the result is greater than or equal 0 (bitmap allocation
successful) then the loop terminates and the function returns 0
(success) despite not having installed an interrupt.
When the result is less than 0 (bitmap allocation fails), it prints an
error message and continues to "work" with that error code which would
eventually end up in the MSI message data.
2) On every invocation the file global pp4xx_msi::msi_virqs bitmap is
allocated thereby leaking the previous one.
IOW, this has never worked and for more than 10 years nobody cared. Remove
the gunk.
Fixes: 3fb7933850 ("powerpc/4xx: Adding PCIe MSI support")
Fixes: 247540b03b ("powerpc/44x: Fix PCI MSI support for Maui APM821xx SoC and Bluestone board")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20211206210223.872249537@linutronix.de
Currently, text_poke_bp() is very strict to only allow patching a
single instruction; however with straight-line-speculation it will be
required to patch: ret; int3, which is two instructions.
As such, relax the constraints a little to allow int3 padding for all
instructions that do not imply the execution of the next instruction,
ie: RET, JMP.d8 and JMP.d32.
While there, rename the text_poke_loc::rel32 field to ::disp.
Note: this fills up the text_poke_loc structure which is now a round
16 bytes big.
[ bp: Put comments ontop instead of on the side. ]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lore.kernel.org/r/20211204134908.082342723@infradead.org
No active MIPS user own this board, so let's remove it.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
LLVM's integrated assembler does not support 'slti <reg>, <imm>':
<instantiation>:16:12: error: invalid operand for instruction
slti $12, (0x6300 | 0x0008)
^
arch/mips/kernel/head.S:86:2: note: while in macro instantiation
kernel_entry_setup # cpu specific setup
^
<instantiation>:16:12: error: invalid operand for instruction
slti $12, (0x6300 | 0x0008)
^
arch/mips/kernel/head.S:150:2: note: while in macro instantiation
smp_slave_setup
^
To increase compatibility with LLVM's integrated assembler, use the full
form of 'slti <reg>, <reg>, <imm>', which matches the rest of
arch/mips/. This does not result in any change for GNU as.
Link: https://github.com/ClangBuiltLinux/linux/issues/1526
Reported-by: Ryutaroh Matsumoto <ryutaroh@ict.e.titech.ac.jp>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
When building with LLVM's integrated assembler, the build errors because
it does not implement -mfix-loongson2f-{jump,nop}:
arch/mips/loongson2ef/Platform:36: *** only binutils >= 2.20.2 have needed option -mfix-loongson2f-nop. Stop.
The error is a little misleading because binutils are not being used in
this case.
To clear this up, remove the as-option calls because binutils 2.23 is
the minimum supported version for building the kernel. At the same time,
remove the cc-option calls for the '-march=' flags, as GCC 5.1.0 is the
minimum supported version.
This change will not fix the LLVM build for CONFIG_CPU_LOONGSON2{E,F},
as it does not implement the loongson2{e,f} march arguments (nor r4600,
so it will error prior to this change) nor the assembler flags mentioned
above but it will make the errors more obvious.
Link: https://github.com/ClangBuiltLinux/linux/issues/1529
Reported-by: Ryutaroh Matsumoto <ryutaroh@ict.e.titech.ac.jp>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
copy_user_offload() will actually push a struct struct xfrm_user_offload,
which is different than (struct xfrm_state *)->xso
(struct xfrm_state_offload)
Fixes: d77e38e612 ("xfrm: Add an IPsec hardware offloading API")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
After commit 9f76779f24 ("MIPS: implement architecture-specific
'pci_remap_iospace()'"), there exists the following warning on the
Loongson64 platform:
loongson-pci 1a000000.pci: IO 0x0018020000..0x001803ffff -> 0x0000020000
loongson-pci 1a000000.pci: MEM 0x0040000000..0x007fffffff -> 0x0040000000
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1 at arch/mips/pci/pci-generic.c:55 pci_remap_iospace+0x84/0x90
resource start address is not zero
...
Call Trace:
[<ffffffff8020dc78>] show_stack+0x40/0x120
[<ffffffff80cf4a0c>] dump_stack_lvl+0x58/0x74
[<ffffffff8023a0b0>] __warn+0xe0/0x110
[<ffffffff80cee02c>] warn_slowpath_fmt+0xa4/0xd0
[<ffffffff80cecf24>] pci_remap_iospace+0x84/0x90
[<ffffffff807f9864>] devm_pci_remap_iospace+0x5c/0xb8
[<ffffffff808121b0>] devm_of_pci_bridge_init+0x178/0x1f8
[<ffffffff807f4000>] devm_pci_alloc_host_bridge+0x78/0x98
[<ffffffff80819454>] loongson_pci_probe+0x34/0x160
[<ffffffff809203cc>] platform_probe+0x6c/0xe0
[<ffffffff8091d5d4>] really_probe+0xbc/0x340
[<ffffffff8091d8f0>] __driver_probe_device+0x98/0x110
[<ffffffff8091d9b8>] driver_probe_device+0x50/0x118
[<ffffffff8091dea0>] __driver_attach+0x80/0x118
[<ffffffff8091b280>] bus_for_each_dev+0x80/0xc8
[<ffffffff8091c6d8>] bus_add_driver+0x130/0x210
[<ffffffff8091ead4>] driver_register+0x8c/0x150
[<ffffffff80200a8c>] do_one_initcall+0x54/0x288
[<ffffffff811a5320>] kernel_init_freeable+0x27c/0x2e4
[<ffffffff80cfc380>] kernel_init+0x2c/0x134
[<ffffffff80205a2c>] ret_from_kernel_thread+0x14/0x1c
---[ end trace e4a0efe10aa5cce6 ]---
loongson-pci 1a000000.pci: error -19: failed to map resource [io 0x20000-0x3ffff]
We can see that the resource start address is 0x0000020000, because
the ISA Bridge used the zero address which is defined in the dts file
arch/mips/boot/dts/loongson/ls7a-pch.dtsi:
ISA Bridge: /bus@10000000/isa@18000000
IO 0x0000000018000000..0x000000001801ffff -> 0x0000000000000000
Based on the above analysis, the architecture-specific pci_remap_iospace()
is not suitable for Loongson64, we should only define pci_remap_iospace()
for Ralink on MIPS based on the commit background.
Fixes: 9f76779f24 ("MIPS: implement architecture-specific 'pci_remap_iospace()'")
Suggested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Tested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Add display/intel_display_trace.[ch] for defining display
tracepoints. The main goal is to reduce cross-includes between gem and
display. It would be possible split up tracing even further, but that
would lead to more boilerplate.
We end up having to include intel_crtc.h in a few places because it was
pulled in implicitly via intel_de.h -> i915_trace.h -> intel_crtc.h, and
that's no longer the case.
There should be no changes to tracepoints.
v3:
- Rebase
v2:
- Define TRACE_INCLUDE_PATH relative to define_trace.h (Chris)
- Remove useless comments (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7862ad764fbd0748d903c76bc632d3d277874e5b.1638961423.git.jani.nikula@intel.com
Follow the style that seems to be prevalent in kernel for undef and
define of TRACE_SYSTEM, TRACE_INCLUDE_PATH, and TRACE_INCLUDE_FILE.
There should be no changes to tracepoints.
v2: Keep TRACE_INCLUDE_PATH relative to define_trace.h (Chris)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0d37790ee70fb60be6f6a73d8bde2013510a7ad8.1638961423.git.jani.nikula@intel.com
ExynosAutoV9 functioning logic mostly follows I2C_TYPE_EXYNOS7, but
timing calculation and configuration procedure is changed: e.g. only
timing_s3 has to be set now.
Another change of HSI2C controller in ExynosAutoV9 SoC is that it's now
a part of USIv2 IP-core. No changes is needed for I2C driver though, as
all USI related configuration is done in USI driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In new Exynos SoCs (like Exynos850) where HSI2C is implemented as a
part of USIv2 block, there are two clocks provided to HSI2C controller:
- PCLK: bus clock (APB), provides access to register interface
- IPCLK: operating IP-core clock; SCL is derived from this one
Both clocks have to be asserted for HSI2C to be functional in that case.
Modify bindings doc to allow specifying bus clock in addition to
already described operating clock.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch adds new "samsung,exynosautov9-hsi2c" compatible.
It is for i2c compatible with HSI2C available on Exynos SoC with USI.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Convert Samsung Exynos High Speed I2C bindings doc to DT schema format.
Changes during bindings conversion:
1. Added missing required clock properties (driver fails when it's
unable to get the clock)
2. Removed properties and descriptions that can be found in
schemas/i2c/i2c-controller.yaml [1]
3. Fixed the example so it can be validated by dtschema
[1] https://github.com/robherring/dt-schema/blob/master/schemas/i2c/i2c-controller.yaml
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Switch the DT binding to a YAML schema to enable the DT validation.
Signed-off-by: David Heidelberg <david@ixit.cz>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver currently assumes that the notify callback is only received
when the device is done with all the queued buffers.
However, this is not true, since the notify callback could be called
without any of the queued buffers being completed (for example, with
virtio-pci and shared interrupts) or with only some of the buffers being
completed (since the driver makes them available to the device in
multiple separate virtqueue_add_sgs() calls).
This can lead to incorrect data on the I2C bus or memory corruption in
the guest if the device operates on buffers which are have been freed by
the driver. (The WARN_ON in the driver is also triggered.)
BUG kmalloc-128 (Tainted: G W ): Poison overwritten
First byte 0x0 instead of 0x6b
Allocated in i2cdev_ioctl_rdwr+0x9d/0x1de age=243 cpu=0 pid=28
memdup_user+0x2e/0xbd
i2cdev_ioctl_rdwr+0x9d/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in i2cdev_ioctl_rdwr+0x1bb/0x1de age=68 cpu=0 pid=28
kfree+0x1bd/0x1cc
i2cdev_ioctl_rdwr+0x1bb/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Fix this by calling virtio_get_buf() from the notify handler like other
virtio drivers and by actually waiting for all the buffers to be
completed.
Fixes: 3cfc883804 ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When scan request on channel 1, it also receive beacon from other
channels, and the beacon also indicate to mac80211 and wpa_supplicant,
and then the bss info appears in radio measurement report of radio
measurement sent from wpa_supplicant, thus lead RRM case fail.
This is to drop the beacon and probe response which is not the same
channel of scanning.
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00049
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211208061752.16564-1-quic_wgong@quicinc.com
Currently there is no validation on the spectral/CFR report
over the db ring buffers from the hardware. Improper/incomplete
DMA by the target can result in invalid data received by host.
Due to this we may populate incorrect data to user space.
This buffer validation support fix this issues by filling some
magic value in the buffer during buffer replenish and check for
the magic value in the buffer received by the target. If host
detect magic value in the received buffer it will drop the buffer.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1637312901-10279-2-git-send-email-quic_vnaralas@quicinc.com
In full monitor mode, monitor destination ring is read before monitor
status ring. mon_dst_ring has ppdu id, reap till the end of PPDU. Add
all the MPDUs to list. Start processing the status ring, if PPDU id in
status ring is lagging behind, reap the status ring, once the PPDU ID
matches, deliver the MSDU to upper layer. If status PPDU id leading,
reap the mon_dst_ring.
The advantage with full monitor mode is hardware has status buffers
available for all the MPDUs in mon_dst_ring, which makes it possible
to deliver more frames to be seen on sniffer.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-4-git-send-email-akolli@codeaurora.org
In full monitor mode, monitor destination ring is read in
software monitor ring descriptor format instead of
reo_entrance_ring format. Add new sw_mon_ring descriptor.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-3-git-send-email-akolli@codeaurora.org
A new hw_param full_monitor_mode is added to enable full
monitor support for QCN9074.
HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE cmd is sent to FW
to enable the full monitor mode.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-2-git-send-email-akolli@codeaurora.org
The old "ak" vendor prefix that was never officially accepted was still
being used in some device trees. Convert to the correct vendor prefix
(i.e. "asahi-kasei").
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TI wlcore DT bindings specify using a single compatible value for
each variant, and the Linux kernel driver matches against the first
compatible value since commit 078b30da3f ("wlcore: add wl1285
compatible") in v4.13.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ADC0 and ADC1 pins are available on external connector J22.
Enable ADC1 which was missing.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This hardware module is close to the am33xx ADC module but instead of
featuring a touchscreen it has a magnetic reader capability.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Back in 2014 a property got misspelled "ti,coordiante-readouts" instead
of "ti,coordinate-readouts".
The year after it got fixed but both are still supported, although this
is not a reason to continue using this old deprecated property.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On the am335x-icev2 board [1], AM3359 PMIC_PWR_EN (ZCZ ball C6) is
connected to PWRHOLD (pin 1) on the TPS65910A3 PMIC. The addition of
system-power-controller to the rtc node will enable the capability of
the RTC driver to poweroff the board.
Based on commit 15c7be47fb7c ("ARM: dts: am335x: Add rtc node as
system-power-controller") by Keerthy in ti-linux-5.4.y branch [2].
[1] https://www.ti.com/tool/TMDSICE3359
[2] git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/linux-omap/20211012191311.879838-1-dfustini@baylibre.com/
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the rtc node system-power-controller property from
am335x-boneblack-common.dtsi to am335x-bone-common.dtsi.
am335x-boneblack-common.dtsi is included by am335x-boneblack.dts,
am335x-boneblack-wireless.dts, am335x-sancloud-bbe.dts and
am335x-sancloud-bbe-lite.dts. All of these dts files also include
am335x-bone-common.dtsi and thus will retain the rtc node
system-power-controller property.
am335x-bone-common.dtsi is also included by am335x-bone.dts [1],
am335x-bonegreen.dts [2] and am335x-bonegreen-wireless.dts [3]. These
boards will now have the rtc node system-power-controller property too.
This is valid as they also have PMIC_POWR_EN (ZCZ C6) connected to
PWR_EN on the TPS65217B PMIC.
Based on commit 15c7be47fb7c ("ARM: dts: am335x: Add rtc node as
system-power-controller") by Keerthy in ti-linux-5.4.y branch [4].
[1] https://beagleboard.org/static/beaglebone/BEAGLEBONE_SCHEM_A3.pdf
[2] https://github.com/SeeedDocument/BeagleBone_Green/blob/master/resources/BEAGLEBONE_GREEN_V1.pdf
[3] https://github.com/SeeedDocument/BeagleBone_Green_Wireless/blob/master/resources/BeagleBone_Green%20Wireless_V1.0_SCH_20160314.pdf
[4] git://git.ti.com/ti-linux-kernel/ti-linux-kernel.git
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Link: https://lore.kernel.org/linux-omap/20211012191311.879838-1-dfustini@baylibre.com/
Suggested-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa ("can: kvaser_usb: Add support for Kvaser CAN/USB devices")
Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Check the direction bit in the error frame packet (EPACK) to determine
which net_device_stats {rx,tx}_errors counter to increase.
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Link: https://lore.kernel.org/all/20211208152122.250852-1-extja@kvaser.com
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In builds with -Warray-bounds, casts from smaller objects to larger
objects will produce warnings. These can be overly conservative, but since
-Warray-bounds has been finding legitimate bugs, it is desirable to turn
it on globally. Instead of casting a u32 to a larger object, redefine
the u32 portion of the header to a separate struct that can be used for
both u32 operations and the distinct header fields. Silences this warning:
drivers/net/wireless/ath/ath6kl/htc_mbox.c: In function 'htc_wait_for_ctrl_msg':
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2275:20: error: array subscript 'struct htc_frame_hdr[0]' is partly outside array bounds of 'u32[1]' {aka 'unsigned int[1]'} [-Werror=array-bounds]
2275 | if (htc_hdr->eid != ENDPOINT_0)
| ^~
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2264:13: note: while referencing 'look_ahead'
2264 | u32 look_ahead;
| ^~~~~~~~~~
This change results in no executable instruction differences.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207063538.2767954-1-keescook@chromium.org
Currently mac80211 will send 3 scan request for each scan of WCN6855,
they are 2.4 GHz/5 GHz/6 GHz band scan. Firmware of WCN6855 will
cache the RNR IE(Reduced Neighbor Report element) which exist in the
beacon of 2.4 GHz/5 GHz of the AP which is co-located with 6 GHz,
and then use the cache to scan in 6 GHz band scan if the 6 GHz scan
is in the same scan with the 2.4 GHz/5 GHz band, this will helpful to
search more AP of 6 GHz. Also it will decrease the time cost of scan
because firmware will use dual-band scan for the 2.4 GHz/5 GHz, it
means the 2.4 GHz and 5 GHz scans are doing simultaneously.
Set the flag IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS for WCN6855 since
it supports 2.4 GHz/5 GHz/6 GHz and it is single pdev which means
all the 2.4 GHz/5 GHz/6 GHz exist in the same wiphy/ieee80211_hw.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211129101309.2931-1-quic_wgong@quicinc.com
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02892.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Cc: stable@vger.kernel.org
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211207142913.1734635-1-sven@narfation.org
Fixed two CHECKs of Alignment should match open parenthesis and flipped
a condition to pull the code in one tab.
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ngo Tak Fong <simon.fodin@gmail.com>
Link: https://lore.kernel.org/r/20211207212223.GA70594@simon-desktop
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only support a single LED. LedPin in struct struct LED_871x is
always LED_PIN_LED0. There's no need to store this info or to pass it
to functions as a parameter.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20211207210537.23382-4-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver uses only led0. Remove the register settings to switch led1
on and off.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20211207210537.23382-3-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The r8188eu driver does not use SwLed1. Calls from other layers to modify
the led state end up in SwLedControlMode1, where SwLed0 is hard-coded.
This patch removes the code to initialise and deinitialise SwLed1 and
the SwLed1 struct itself.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20211207210537.23382-2-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adapter->HalData is used in the GET_HAL_DATA macro all across the
driver code but nobody checks if its allocation in
rtl188eu_alloc_haldata() was successful or not.
To avoid errors when the allocation fails convert the type of field
HalData from void pointer to struct hal_data_8188eu. Remove
GET_HAL_DATA, rtl8188eu_alloc_haldata(), rtl8188e_free_hal_data().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Link: https://lore.kernel.org/r/20211207140405.8673-1-straube.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF/AjYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG1hkIAJ6sFDbvb4M4LMwf
Slh2NVL9o5sLMBDzVwnVlyMSKDbMn1WBKreGssaLgZjGDc74lxsdSmw5l9MZm0JN
xlq95Q6XFiuu+0qDHPWwfDz3JFO4TqW2ZLLPWk9NnkNbRXqccSrlVRi1RpgE1t3/
NUtS8CQLu6A2BYMc6mkk3aV6IwSNKOkWbM5eBHSvU4j8B6lLbNQop0AfO/wyY1xB
U6LiVE1RpN/b7Yv+75ITtNzuHzVIBx6305FvSnOlKbMKKvIClt96Vd2OeuoEkK+6
wGU8JraB1+fc0GckAhynNrjWQWdvi0MAhFWWEJxjS20OGcV1rXDduNfkVNauO1Zn
+dNyJ3s=
=g9fz
-----END PGP SIGNATURE-----
Merge tag 'v5.15' into next
Sync up with the mainline to get the latest APIs and DT bindings.
The pointer t is being initialized with a value that is never read. The
pointer is re-assigned a value a littler later on, hence the initialization
is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211207224718.59593-1-colin.i.king@gmail.com
Vendor prefix shouldn't start with capital letter. The Elpida Memory
compatible was never used in practice, hence just correct the compatible.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The following warning is triggered when I used clang compiler
to build the selftest.
/.../prog_tests/btf_dedup_split.c:368:6: warning: variable 'btf2' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (!ASSERT_OK(err, "btf_dedup"))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
/.../prog_tests/btf_dedup_split.c:424:12: note: uninitialized use occurs here
btf__free(btf2);
^~~~
/.../prog_tests/btf_dedup_split.c:368:2: note: remove the 'if' if its condition is always false
if (!ASSERT_OK(err, "btf_dedup"))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/.../prog_tests/btf_dedup_split.c:343:25: note: initialize the variable 'btf2' to silence this warning
struct btf *btf1, *btf2;
^
= NULL
Initialize local variable btf2 = NULL and the warning is gone.
Fixes: 9a49afe6f5 ("selftests/bpf: Add btf_dedup case with duplicated structs within CU")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20211209050403.1770836-1-yhs@fb.com
[why/how]
The function can be called on boot or after suspend when
links are not initialized, to prevent it guard it with
NULL pointer check
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
