The only usage of rkvdec_m2m_ops is to pass its address to v4l2_m2m_init(),
which takes a pointer to const v4l2_m2m_ops as argument. Make it const
to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only usage of m2m_ops is to pass its address to v4l2_m2m_init(),
which takes a pointer to const v4l2_m2m_ops as argument. Make it const
to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
PXP allows clockwise rotation of 0°, 90°, 180° and 270°.
Add support for it.
Tested on a imx6ull-evk.
For example, to rotate 90° the following Gstreamer pipeline can
be used:
gst-launch-1.0 videotestsrc ! video/x-raw,width=640,height=480 ! \
v4l2convert extra-controls=cid,rotate=90 ! \
video/x-raw,width=120,height=160 ! fbdevsink
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
After devm_request_threaded_irq() is called there is a chance that an
interrupt may occur before the spinlock is initialized, which will trigger
a kernel oops.
To prevent that, move the initialization of the spinlock prior to
requesting the interrupts.
Fixes: 51abcf7fdb ("media: imx-pxp: add i.MX Pixel Pipeline driver")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
PHTW register is selected based on default bit rate from Table[1].
for the bit rates less than or equal to 250. Currently first
value of default bit rate which is greater than or equal to
the caculated mbps is selected. This selection can be further
improved by selecting the default bit rate which is nearest to
the calculated value.
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.12]
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a warning message when the selected PHY speed is less
than supported minimum PHY speed given in the hsfreq table[1].
For raspberry pi camera capture on Kingfisher board with resolution
640x480, the calculated PHY speed is 48 mbps which is less than
the minimum PHY speed 80 Mbps from the table[1]. But in this cases
capture is successful.
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.9]
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
hsfreqrange should be chosen based on the calculated mbps which
is closer to the default bit rate and within the range as per
table[1]. But current calculation always selects first value which
is greater than or equal to the calculated mbps which may lead
to chosing a wrong range in some cases.
For example for 360 mbps for H3/M3N
Existing logic selects
Calculated value 360Mbps : Default 400Mbps Range [368.125 -433.125 mbps]
This hsfreqrange is out of range.
The logic is changed to get the default value which is closest to the
calculated value [1]
Calculated value 360Mbps : Default 350Mbps Range [320.625 -380.625 mpbs]
[1] specs r19uh0105ej0200-r-car-3rd-generation.pdf [Table 25.9]
Please note that According to Renesas in Table 25.9 the range for
220 default value is corrected as below
|Range (Mbps) | Default Bit rate (Mbps) |
-----------------------------------------------
| 197.125-244.125 | 220 |
-----------------------------------------------
Fixes: 769afd212b ("media: rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver")
Signed-off-by: Suresh Udipi <sudipi@jp.adit-jv.com>
Signed-off-by: Kazuyoshi Akiyama <akiyama@nds-osk.co.jp>
Signed-off-by: Michael Rodin <mrodin@de.adit-jv.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
PM8226 (used in MSM8226) has v1 smbb hardware and works fine with the
current driver.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The charger in PM8226 (used in MSM8226) is similar to the charger in
PM8941.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link drm_fb_cma_helper.o into drm_cma_helper.ko if CONFIG_DRM_KMS_HELPER
has been set. Remove CONFIG_DRM_KMS_CMA_HELPER config option. Selecting
KMS helpers and CMA will now automatically enable CMA KMS helpers.
Some drivers' Kconfig files did not correctly select KMS or CMA helpers.
Fix this as part of the change.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211106193509.17472-3-tzimmermann@suse.de
The MIPI DBI helpers access struct drm_gem_cma_object.vaddr in a
few places. Replace all instances with the correct generic GEM
functions. Use drm_gem_fb_vmap() for mapping a framebuffer's GEM
objects and drm_gem_fb_vunmap() for unmapping them. This removes
the dependency on CMA helpers within MIPI DBI.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211106193509.17472-2-tzimmermann@suse.de
Convert the Renesas JPEG Processing Unit Device Tree binding
documentation to json-schema.
Document missing properties.
Update the example to match reality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implement fwnode parsing at probe time.
Check if the bus and number of lanes are supported.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Simplify probe function by adding a local variable dev instead of using
&client->dev all the time.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ACPI _HID INT347A represents the OV8865 sensor, the driver for which can
support the platforms that the cio2-bridge serves. Add it to the array
of supported sensors so the bridge will connect the sensor to the CIO2
device.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The maximum gain figure in the v4l2 ctrl is wrong. The field is 12 bits
wide, which is where the 8191 figure comes from, but the datasheet is
specific that maximum gain is 16x (the low seven bits are fractional, so
16x gain is 2048)
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a chance that regulator_get() returns -EPROBE_DEFER, in which
case printing an error message is undesirable. To avoid spurious messages
in dmesg in the event that -EPROBE_DEFER is returned, use dev_err_probe()
on error paths for regulator_get().
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver currently has the unit of the V4L2_CID_EXPOSURE control
as 1/16th of a line. This is what the sensor expects, but isn't very
intuitive. Switch the control to be in units of a line and simply do the
16x multiplication before passing the value to the sensor.
The datasheet for this sensor gives minimum exposure as 2 lines, so take
the opportunity to correct the lower bounds of the control.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov8865 driver by attempting to parse them from firmware.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Exposure limits depend on the total height; when vblank is altered (and
thus the total height is altered), change the exposure limits to reflect
the new cap.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The HTS values for some of the modes in the ov8865 driver are a bit
unusual, coming in lower than the output_size_x is set to. It seems
like they might be calculated to fit the desired framerate into a
configuration with just two data lanes. To bring this more in line
with expected behaviour, raise the HTS values above the output_size_x.
The corollary of that change is that the hardcoded frame intervals
against the modes no longer make sense, so remove those entirely.
Update the .g/s_frame_interval() callbacks to calculate the frame
interval based on the current mode and the vblank and hblank settings.
The implementation of the .enum_frame_interval() callback is no longer
suitable since the possible frame rate is now a continuous range depending
on the vblank control setting, so remove that callback entirely.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2_CID_HBLANK control to the ov8865 driver. This is read only
with timing control intended to be done via vblanking alone.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a V4L2_CID_VBLANK control to the ov8865 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The V4L2_CID_GAIN control for this driver configures registers that
the datasheet specifies as analogue gain. Switch the control's ID
to V4L2_CID_ANALOGUE_GAIN.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver's v4l2_subdev_pad_ops currently does not include
.get_selection() - add support for that callback.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver as written expects a 24MHz input clock, but the sensor
is sometimes found on x86 platforms with a 19.2MHz input clock supplied.
Add a set of PLL configurations to the driver to support that rate too.
As ACPI doesn't auto-configure the clock rate, check for a clock-frequency
during probe and set that rate if one is found.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 driver is one of those that can be connected to a CIO2
device by the cio2-bridge code. This means that the absence of an
endpoint for this device is not necessarily fatal, as one might be
built by the cio2-bridge when it probes. Return -EPROBE_DEFER if no
endpoint is found rather than a fatal error.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PLL configuration defined here sets 72MHz (which is correct), not
80MHz. Correct the comment.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov8865 sensor is sometimes found on x86 platforms enumerated via ACPI.
Add an ACPI match table to the driver so that it's probed on those
platforms.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ov8865_state_init() calls ov8865_state_mipi_configure() which uses
__v4l2_ctrl_s_ctrl[_int64](). This means that sensor->mutex (which
is also sensor->ctrls.handler.lock) must be locked before calling
ov8865_state_init().
Note ov8865_state_mipi_configure() is also used in other places where
the lock is already held so it cannot be changed itself.
This fixes the following lockdep kernel WARN:
[ 13.233421] WARNING: CPU: 0 PID: 8 at drivers/media/v4l2-core/v4l2-ctrls-api.c:833 __v4l2_ctrl_s_ctrl+0x4d/0x60 [videodev]
...
[ 13.234063] Call Trace:
[ 13.234074] ov8865_state_configure+0x98b/0xc00 [ov8865]
[ 13.234095] ov8865_probe+0x4b1/0x54c [ov8865]
[ 13.234117] i2c_device_probe+0x13c/0x2d0
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The kerneldoc for pm_runtime_set_suspended() says:
"It is not valid to call this function for devices with runtime PM
enabled"
To satisfy that requirement, re-order the calls so that
pm_runtime_enable() is the last one.
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a link frequency to the cio2-bridge table of supported sensors.
This means that the driver can parse supported link frequencies from
firmware in the usual way and validate that it can accommodate them.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The OV5693 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2. The
chip is capable of a single lane configuration, but currently only two
lanes are supported.
Most of the sensor's features are supported, with the main exception
being the lens correction algorithm.
The driver provides all mandatory, optional and recommended V4L2 controls
for maximum compatibility with libcamera.
[mchehab: fixed a coding style warning]
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The .suspend() and .resume() runtime_pm operations for the ipu3-cio2
driver currently do not handle the sensor's stream. Setting .s_stream() on
or off for the sensor subdev means that sensors will pause and resume the
stream at the appropriate time even if their drivers don't implement those
operations.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Current driver supports only SRGGB 10 bit RAW bayer format.
Add the enum_mbus_code implementation to report this format supported.
# v4l2-ctl -d /dev/v4l-subdev3 --list-subdev-mbus-codes
ioctl: VIDIOC_SUBDEV_ENUM_MBUS_CODE (pad=0)
0x300f: MEDIA_BUS_FMT_SRGGB10_1X10
#
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The MAX9286 has not explicitly declared a dependency upon VIDEO_V4L2.
While this dependency has likely always been met by configurations
including it, the device does use V4L2 core, and should depend upon it.
Add VIDEO_V4L2 as a dependency to match other drivers and prevent
failures when compile testing.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some bootloaders (e.g. VxWorks 5.5 System Boot) on TX49 systems do not
support loading 64-bit kernel images. Work around this by selecting
BOOT_ELF32, to support running both 32-bit ("vmlinux" with
CONFIG_32BIT=y) and 64-bit ("vmlinux.32" with CONFIG_64BIT=y) Linux
kernels on TX49 devices with such a boot loader.
Suggested-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
There are reports that 48kHz audio does not work on the WeTek Play 2
(which uses a GXBB SoC), while 44.1kHz audio works fine on the same
board. There are also reports of 48kHz audio working fine on GXL and
GXM SoCs, which are using an (almost) identical AIU (audio controller).
Experimenting has shown that MPLL0 is causing this problem. In the .dts
we have by default:
assigned-clocks = <&clkc CLKID_MPLL0>,
<&clkc CLKID_MPLL1>,
<&clkc CLKID_MPLL2>;
assigned-clock-rates = <294912000>,
<270950400>,
<393216000>;
The MPLL0 rate is divisible by 48kHz without remainder and the MPLL1
rate is divisible by 44.1kHz without remainder. Swapping these two clock
rates "fixes" 48kHz audio but breaks 44.1kHz audio.
Everything looks normal when looking at the info provided by the common
clock framework while playing 48kHz audio (via I2S with mclk-fs = 256):
mpll_prediv 1 1 0 2000000000
mpll0_div 1 1 0 294909641
mpll0 1 1 0 294909641
cts_amclk_sel 1 1 0 294909641
cts_amclk_div 1 1 0 12287902
cts_amclk 1 1 0 12287902
meson-clk-msr however shows that the actual MPLL0 clock is off by more
than 38MHz:
mp0_out 333322917 +/-10416Hz
The rate seen by meson-clk-msr is very close to what we would get when
SDM (the fractional part) was ignored:
(2000000000Hz * 16384) / ((16384 * 6) = 333.33MHz
If SDM was considered the we should get close to:
(2000000000Hz * 16384) / ((16384 * 6) + 12808) = 294.9MHz
Further experimenting shows that HHI_MPLL_CNTL7[15] does not have any
effect on the rate of MPLL0 as seen my meson-clk-msr (regardless of
whether that bit is zero or one the rate is always the same according to
meson-clk-msr). Using HHI_MPLL_CNTL[25] on the other hand as SDM_EN
results in SDM being considered for the rate output by the hardware. The
rate - as seen by meson-clk-msr - matches with what we expect when
SDM_EN is enabled (fractional part is being considered, resulting in a
294.9MHz output) or disable (fractional part being ignored, resulting in
a 333.33MHz output).
Reported-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20211031135006.1508796-1-martin.blumenstingl@googlemail.com
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we use dmaengine_terminate_sync in
i2c_xfer and i2c_smbus_xfer handlers and rely on
dmaengine_terminate_async within interrupt handlers
(transmission error cases).
dmaengine_synchronize is added within i2c_xfer and i2c_smbus_xfer handler
to finalize terminate started in interrupt handlers.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When getting an access timeout, ensure that the bus is in a proper
state prior to returning the error.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Generally, kvm->lock is not taken for a long time, but
sev_lock_two_vms is different: it takes vCPU locks
inside, so userspace can hold it back just by calling
a vCPU ioctl. Play it safe and use mutex_lock_killable.
Message-Id: <20211123005036.2954379-13-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Taking the lock is useless since there are no other references,
and there are already accesses (e.g. to sev->enc_context_owner)
that do not take it. So get rid of it.
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211123005036.2954379-12-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMs that mirror an encryption context rely on the owner to keep the
ASID allocated. Performing a KVM_CAP_VM_MOVE_ENC_CONTEXT_FROM
would cause a dangling ASID:
1. copy context from A to B (gets ref to A)
2. move context from A to L (moves ASID from A to L)
3. close L (releases ASID from L, B still references it)
The right way to do the handoff instead is to create a fresh mirror VM
on the destination first:
1. copy context from A to B (gets ref to A)
[later] 2. close B (releases ref to A)
3. move context from A to L (moves ASID from A to L)
4. copy context from L to M
So, catch the situation by adding a count of how many VMs are
mirroring this one's encryption context.
Fixes: 0b020f5af0 ("KVM: SEV: Add support for SEV-ES intra host migration")
Message-Id: <20211123005036.2954379-11-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that we have a facility to lock two VMs with deadlock
protection, use it for the creation of mirror VMs as well. One of
COPY_ENC_CONTEXT_FROM(dst, src) and COPY_ENC_CONTEXT_FROM(src, dst)
would always fail, so the combination is nonsensical and it is okay to
return -EBUSY if it is attempted.
This sidesteps the question of what happens if a VM is
MOVE_ENC_CONTEXT_FROM'd at the same time as it is
COPY_ENC_CONTEXT_FROM'd: the locking prevents that from
happening.
Cc: Peter Gonda <pgonda@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211123005036.2954379-10-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I am putting the tests in sev_migrate_tests because the failure conditions are
very similar and some of the setup code can be reused, too.
The tests cover both successful creation of a mirror VM, and error
conditions.
Cc: Peter Gonda <pgonda@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Message-Id: <20211123005036.2954379-9-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
