When a disk has write caching disabled, we skip submission of a bio with
flush and sync requests before writing the superblock, since it's not
needed. However when the integrity checker is enabled, this results in
reports that there are metadata blocks referred by a superblock that
were not properly flushed. So don't skip the bio submission only when
the integrity checker is enabled for the sake of simplicity, since this
is a debug tool and not meant for use in non-debug builds.
fstests/btrfs/220 trigger a check-integrity warning like the following
when CONFIG_BTRFS_FS_CHECK_INTEGRITY=y and the disk with WCE=0.
btrfs: attempt to write superblock which references block M @5242880 (sdb2/5242880/0) which is not flushed out of disk's write cache (block flush_gen=1, dev->flush_gen=0)!
------------[ cut here ]------------
WARNING: CPU: 28 PID: 843680 at fs/btrfs/check-integrity.c:2196 btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
CPU: 28 PID: 843680 Comm: umount Not tainted 5.15.0-0.rc5.39.el8.x86_64 #1
Hardware name: Dell Inc. Precision T7610/0NK70N, BIOS A18 09/11/2019
RIP: 0010:btrfsic_process_written_superblock+0x22a/0x2a0 [btrfs]
RSP: 0018:ffffb642afb47940 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 00000000ffffffff RSI: ffff8b722fc97d00 RDI: ffff8b722fc97d00
RBP: ffff8b5601c00000 R08: 0000000000000000 R09: c0000000ffff7fff
R10: 0000000000000001 R11: ffffb642afb476f8 R12: ffffffffffffffff
R13: ffffb642afb47974 R14: ffff8b5499254c00 R15: 0000000000000003
FS: 00007f00a06d4080(0000) GS:ffff8b722fc80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fff5cff5ff0 CR3: 00000001c0c2a006 CR4: 00000000001706e0
Call Trace:
btrfsic_process_written_block+0x2f7/0x850 [btrfs]
__btrfsic_submit_bio.part.19+0x310/0x330 [btrfs]
? bio_associate_blkg_from_css+0xa4/0x2c0
btrfsic_submit_bio+0x18/0x30 [btrfs]
write_dev_supers+0x81/0x2a0 [btrfs]
? find_get_pages_range_tag+0x219/0x280
? pagevec_lookup_range_tag+0x24/0x30
? __filemap_fdatawait_range+0x6d/0xf0
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
? find_first_extent_bit+0x9b/0x160 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
write_all_supers+0x1b3/0xa70 [btrfs]
? __raw_callee_save___native_queued_spin_unlock+0x11/0x1e
btrfs_commit_transaction+0x59d/0xac0 [btrfs]
close_ctree+0x11d/0x339 [btrfs]
generic_shutdown_super+0x71/0x110
kill_anon_super+0x14/0x30
btrfs_kill_super+0x12/0x20 [btrfs]
deactivate_locked_super+0x31/0x70
cleanup_mnt+0xb8/0x140
task_work_run+0x6d/0xb0
exit_to_user_mode_prepare+0x1f0/0x200
syscall_exit_to_user_mode+0x12/0x30
do_syscall_64+0x46/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f009f711dfb
RSP: 002b:00007fff5cff7928 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
RAX: 0000000000000000 RBX: 000055b68c6c9970 RCX: 00007f009f711dfb
RDX: 0000000000000001 RSI: 0000000000000000 RDI: 000055b68c6c9b50
RBP: 0000000000000000 R08: 000055b68c6ca900 R09: 00007f009f795580
R10: 0000000000000000 R11: 0000000000000246 R12: 000055b68c6c9b50
R13: 00007f00a04bf184 R14: 0000000000000000 R15: 00000000ffffffff
---[ end trace 2c4b82abcef9eec4 ]---
S-65536(sdb2/65536/1)
-->
M-1064960(sdb2/1064960/1)
Reviewed-by: Filipe Manana <fdmanana@gmail.com>
Signed-off-by: Wang Yugui <wangyugui@e16-tech.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Ordered work functions aren't guaranteed to be handled by the same thread
which executed the normal work functions. The only way execution between
normal/ordered functions is synchronized is via the WORK_DONE_BIT,
unfortunately the used bitops don't guarantee any ordering whatsoever.
This manifested as seemingly inexplicable crashes on ARM64, where
async_chunk::inode is seen as non-null in async_cow_submit which causes
submit_compressed_extents to be called and crash occurs because
async_chunk::inode suddenly became NULL. The call trace was similar to:
pc : submit_compressed_extents+0x38/0x3d0
lr : async_cow_submit+0x50/0xd0
sp : ffff800015d4bc20
<registers omitted for brevity>
Call trace:
submit_compressed_extents+0x38/0x3d0
async_cow_submit+0x50/0xd0
run_ordered_work+0xc8/0x280
btrfs_work_helper+0x98/0x250
process_one_work+0x1f0/0x4ac
worker_thread+0x188/0x504
kthread+0x110/0x114
ret_from_fork+0x10/0x18
Fix this by adding respective barrier calls which ensure that all
accesses preceding setting of WORK_DONE_BIT are strictly ordered before
setting the flag. At the same time add a read barrier after reading of
WORK_DONE_BIT in run_ordered_work which ensures all subsequent loads
would be strictly ordered after reading the bit. This in turn ensures
are all accesses before WORK_DONE_BIT are going to be strictly ordered
before any access that can occur in ordered_func.
Reported-by: Chris Murphy <lists@colorremedies.com>
Fixes: 08a9ff3264 ("btrfs: Added btrfs_workqueue_struct implemented ordered execution based on kernel workqueue")
CC: stable@vger.kernel.org # 4.4+
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2011928
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Tested-by: Chris Murphy <chris@colorremedies.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
[BUG]
The following script can cause btrfs to crash:
$ mount -o compress-force=lzo $DEV /mnt
$ dd if=/dev/urandom of=/mnt/foo bs=4k count=1
$ sync
The call trace looks like this:
general protection fault, probably for non-canonical address 0xe04b37fccce3b000: 0000 [#1] PREEMPT SMP NOPTI
CPU: 5 PID: 164 Comm: kworker/u20:3 Not tainted 5.15.0-rc7-custom+ #4
Workqueue: btrfs-delalloc btrfs_work_helper [btrfs]
RIP: 0010:__memcpy+0x12/0x20
Call Trace:
lzo_compress_pages+0x236/0x540 [btrfs]
btrfs_compress_pages+0xaa/0xf0 [btrfs]
compress_file_range+0x431/0x8e0 [btrfs]
async_cow_start+0x12/0x30 [btrfs]
btrfs_work_helper+0xf6/0x3e0 [btrfs]
process_one_work+0x294/0x5d0
worker_thread+0x55/0x3c0
kthread+0x140/0x170
ret_from_fork+0x22/0x30
---[ end trace 63c3c0f131e61982 ]---
[CAUSE]
In lzo_compress_pages(), parameter @out_pages is not only an output
parameter (for the number of compressed pages), but also an input
parameter, as the upper limit of compressed pages we can utilize.
In commit d4088803f5 ("btrfs: subpage: make lzo_compress_pages()
compatible"), the refactoring doesn't take @out_pages as an input, thus
completely ignoring the limit.
And for compress-force case, we could hit incompressible data that
compressed size would go beyond the page limit, and cause the above
crash.
[FIX]
Save @out_pages as @max_nr_page, and pass it to lzo_compress_pages(),
and check if we're beyond the limit before accessing the pages.
Note: this also fixes crash on 32bit architectures that was suspected to
be caused by merge of btrfs patches to 5.16-rc1. Reported in
https://lore.kernel.org/all/20211104115001.GU20319@twin.jikos.cz/ .
Reported-by: Omar Sandoval <osandov@fb.com>
Fixes: d4088803f5 ("btrfs: subpage: make lzo_compress_pages() compatible")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ add note ]
Signed-off-by: David Sterba <dsterba@suse.com>
Move interrupts allocation from exynos4_timer_resources() into separate
function together with the interrupt number parsing code from
mct_init_dt(), so the code for managing interrupts is kept together.
While touching exynos4_timer_resources() function, move of_iomap() to it.
No functional changes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211101193531.15078-2-semen.protsenko@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Add support for the MAX77976 3.5/5.5A 1-Cell Li+ Battery Charger.
This is a simple implementation enough to be used as a simple battery
charger without OTG and boost.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Some chargers can keep the system powered from the mains even when no
battery is present. It this case none of the currently defined health
statuses applies. Add a new status to report that no battery is present.
Suggested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
s2idle and runtime pm puts the pci gfx device in D3Hot, ACPI runtime
monitors the pci tree,if it sees complete tree as D3Hot,it transitions
the device to D3Cold.But i915 do not have D3Cold support in S2idle or in
runtime pm. so disabling D3cold in above flows and its FIXME.
Added pci D3Cold enable/disable in s2idle and runtime suspend/resume
flows.
Signed-off-by: Tilak Tangudu <tilak.tangudu@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211115154054.3220476-1-tilak.tangudu@intel.com
This is defined as 64 for the devices/firmware that were chosen.
So, evaluate the macros accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As we're using the firmware from Intel Aero, ensure that the
logic inside sh_css as similar as possible to such driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's a note at the uninit function that warns about issues
with mipi frames de-allocation. print a warning if the problem
ever happens.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Such function doesn't exist on Intel Aero driver. As we're using
its firmware, it may mean that this is not compatible with the
current file. So, drop it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are some dead code meant to suppress "C_RUN" warnings.
Drop it from sh_css.c, as it doesn't make much sense.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's a commented dead code related to some future thing
to be implemented. As this won't happen, as it would require
a newer firmware, just drop the code.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are two versions of those functions. It turns that the
choosen firmware use the old version. So, drop the unused
ones and ensure that all devices will use the right functions.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Yocto Aero driver for ISP2401 sets my_css_save.loaded_fw.
As we're using the same firmware, remove the ifdef there.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those two vars are meaningful only with some ISP2401 firmwares.
The one we chose to support doesn't use, so simply drop the
extra code.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are a couple of places where {} are used just to
define a new var. Just move the var to the top of the function
and get rid of that ugly blocks.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the coding style for the comments at this file.
While here, drop a do-nothing if logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that the input system always declare rx_cfg_t, we can
remove the ifdef ISP2401 from this header.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several stucts under ISP2400 that could be moved
to the global file without causing any build issues.
Move those to the common header, in order to reduce the number
of things that are #ifdef dependent.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
ia_css_dequeue_event() is just an alias to ia_css_dequeue_psys_event(),
and atomisp_css_dequeue_event() do nothing but calling the event
dequeue logic.
Get rid of both abstractions, calling the function directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The succ var tracks memory allocation erros on this function.
Fix it, in order to stop this W=1 Werror in clang:
drivers/staging/media/atomisp/pci/sh_css_params.c:2430:7: error: variable 'succ' set but not used [-Werror,-Wunused-but-set-variable]
bool succ = true;
^
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Allow the sensor to report the per-resolution frame interval.
It should be noticed that, despite the ov2680 datasheet says
that, for resolutions <= 1280x720, the sensor supports 60fps,
the data at ov2680.h tells otherwise, limiting it to 30fps.
Not sure yet if this is a limitation of atomisp or if it is
just because the tables are incorrect.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ov2680 supports a maximum bandwidth of 660Mbps and allows
up to 60fps when the resolution is below 720p.
Adjust the sensor's table to reflect that.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The sensor resolution arrays have two unused fields. Drop them.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several resolutions defined for this sensor, but just
two are currently uncommented. Change the driver to allow other
resolutions to also be used.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix this clang Werror with W=1:
drivers/staging/media/atomisp/i2c/atomisp-gc2235.c:573:6: error: variable 'ret' set but not used [-Werror,-Wunused-but-set-variable]
int ret = -1;
^
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix this clang Werror with W=1:
drivers/staging/media/ipu3/ipu3-css-params.c:774:8: error: variable 'pin_scale' set but not used [-Werror,-Wunused-but-set-variable]
int pin_scale = 0;
^
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since the DW_SPI_CAP_DWC_HSSI capability has just been replaced with using
the DW SSI IP-core versions interface, the DW SPI capability flags are now
represented with a gap. Let's fix it by redefining the DW_SPI_CAP_DFS32
macro to setting BIT(2) of the capabilities field.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Since there is a common IP-core and component versions interface available
we can use it to differentiate the DW HSSI device features in the code.
Let's remove the corresponding DWC_HSSI capability flag then and use the
dw_spi_ip_is() macro instead.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver currently supports two IP-core versions. It's DW APB SSI which
is older version of the controller with APB system bus interface, and DW
SSI controller with AHB bus interface. The later one is supposed to be a
new generation high-speed SSI. Even though both of these IP-cores have got
an almost identical registers space there are some differences. The driver
differentiates these distinctions by the DW_SPI_CAP_DWC_HSSI capability
flag. In addition to that each DW SSI IP-core is equipped with a Synopsys
Component version register, which encodes the IP-core release ID the has
been synthesized from. Seeing we are going to need the later one to
differentiate some controller peculiarities it would be better to have a
unified interface for both IP-core line and release versions instead of
using each of them separately.
Introduced here IP-core versioning interface consists of two parts:
1) IDs of the IP-core (virtual) and component versions.
2) a set of macro helpers to identify current IP-core and component
versions.
So the platform code is supposed to assign a proper IP-core version based
on it's platform -knowledge. The main driver initialization method reads
the IP-core release ID from the SSI component version register. That data
is used by the helpers to distinguish one IP-core release from another.
Thus the rest of the driver can use these macros to implement the
conditional code execution based on the specified IP-core and version IDs.
Collect the IP-core versions interface and the defined capabilities at the
top of the header file since they represent a common device description
data and so to immediately available for the driver hackers.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver has been using the offset/bitwise-shift-based approach for the
CSR fields R/W operations since it was merged into the kernel. It can be
simplified by using the macros defined in the linux/bitfield.h and
linux/bit.h header files like BIT(), GENMASK(), FIELD_PREP(), FIELD_GET(),
etc where it is required, for instance in the cached cr0 preparation
method. Thus in order to have the FIELD_*()-macros utilized we just need
to convert the macros with the CSR-fields offsets to the masks with the
corresponding registers fields definition. That's where the GENMASK() and
BIT() macros come in handy. After that the masks can be used in the
FIELD_*()-macros where it's appropriate.
We also need to convert the macros with the CRS-bit flags using the manual
bitwise shift operations (x << y) to using the BIT() macro. Thus we'll
have a more coherent set of the CSR-related macros.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Mostly due to a long driver history it's methods and macro names look a
bit messy. In particularly that concerns the code their prefixes. A
biggest part of the driver functions and macros have got the dw_spi/DW_SPI
prefixes. But there are some entities which have been just
"spi_/SPI_"-prefixed. Especially that concerns the CSR and their fields
macro definitions. It makes the code harder to comprehend since such
methods and macros can be easily confused with the global SPI-subsystem
exports. In this case the only possible way to more or less quickly
distinguish one naming space from another is either by context or by the
argument type, which most of the times isn't that easy anyway. In addition
to that a new DW SSI IP-core support has been added in the framework of
commit e539f435cb ("spi: dw: Add support for DesignWare DWC_ssi"), which
introduced a new set or macro-prefixes to describe CTRLR0-specific fields
and worsen the situation. Finally there are methods with
no DW SPI driver-reference prefix at all, that make the code reading even
harder. So in order to ease the driver hacking let's bring the code naming
to a common base:
1) Each method is supposed to have "dw_spi_" prefix so to be easily
distinguished from the kernel API, e.g. SPI-subsystem methods and macros.
(Exception is the local implementation of the readl/writel methods since
being just the regspace accessors.)
2) Each generically used macro should have DW_SPI_-prefix thus being
easily comprehended as the local driver definition.
3) DW APB SSI and DW SSI specific macros should have prefixes as DW_PSSI_
and DW_HSSI_ respectively so referring to the system buses they support
(APB and AHB similarly to the DT clocks naming like pclk, hclk).
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The dw_ssi_type enumeration describes the SPI frame formats the controller
supports, like Motorola SPI, Texas Instruments SSP and National
Semiconductors Microwire, that is the serial protocol utilized for the
SPI-transfers. Depending on the DW SSI IP-core configuration the protocol
could be either fixed or selectable. If it is changebale the protocol can
be selected by means of the CTRL0.FRF field, which possible values encoded
by the dw_ssi_type enumeration. Aside with the denoted enum the field
values are also described by a set of SPI_FRF_{SPI,SSP,MICROWIRE} macros.
Thus currently the DW SPI driver has got two entities describing the same
data. Let's get rid of the enumeration one then, since first it hasn't
been used as enumeration-type but merely as a parametrized values set and
second that would unify the macro-based CSR read/write interface of the
driver. While at it convert the macro names to be more descriptive about
the protocols they represent.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The exported from the DW SPI driver core/DMA symbols are only used by the
spi-dw-{mmio,pci,bt1}.o objects. Add these symbols to a separate
namespace then and make sure the depended modules have it imported.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20211115181917.7521-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
When an i2c remove callback fails, the i2c core emits a generic error
message and still removes the device. Apart from the message there the
return value isn't further used.
So don't return an error code after having already emitted a driver
specific warning about the problem to prevent two messages about the
same issue.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211116110951.1213566-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
