The driver tried to use Linux' native software I2C bus master
(i2c-algo-bits) for exporting the I2C interface that talks to the SFP
cage(s) towards userspace. As-is, however, the physical SCL/SDA pins
were not moving at all, staying at logical 1 all the time.
The main culprit was the I2CPARAMS register where igb was not setting
the I2CBB_EN bit. That meant that all the careful signal bit-banging was
actually not being propagated to the chip pads (I verified this with a
scope).
The bit-banging was not correct either, because I2C is supposed to be an
open-collector bus, and the code was driving both lines via a totem
pole. The code was also trying to do operations which did not make any
sense with the i2c-algo-bits, namely manipulating both SDA and SCL from
igb_set_i2c_data (which is only supposed to set SDA). I'm not sure if
that was meant as an optimization, or was just flat out wrong, but given
that the i2c-algo-bits is set up to work with a totally dumb GPIO-ish
implementation underneath, there's no need for this code to be smart.
The open-drain vs. totem-pole is fixed by the usual trick where the
logical zero is implemented via regular output mode and outputting a
logical 0, and the logical high is implemented via the IO pad configured
as an input (thus floating), and letting the mandatory pull-up resistors
do the rest. Anything else is actually wrong on I2C where all devices
are supposed to have open-drain connection to the bus.
The missing I2CBB_EN is set (along with a safe initial value of the
GPIOs) just before registering this software I2C bus.
The chip datasheet mentions HW-implemented I2C transactions (SFP EEPROM
reads and writes) as well, but I'm not touching these for simplicity.
Tested on a LR-Link LRES2203PF-2SFP (which is an almost-miniPCIe form
factor card, a cable, and a module with two SFP cages). There was one
casualty, an old broken SFP we had laying around, which was used to
solder some thin wires as a DIY I2C breakout. Thanks for your service.
With this patch in place, I can `i2cdump -y 3 0x51 c` and read back data
which make sense. Yay.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
See-also: https://www.spinics.net/lists/netdev/msg490554.html
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix the following coccicheck warning:
./drivers/net/ethernet/intel/i40e/i40e_xsk.c:229:35-40: WARNING:
conversion to bool not needed here
./drivers/net/ethernet/intel/ice/ice_xsk.c:399:35-40: WARNING:
conversion to bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fourth set of patches for v5.16. Mostly fixes this time, wcn36xx and
iwlwifi have some new features but nothing really out of ordinary. We
have one conflict with kspp tree.
Conflicts:
kspp tree has a conflict in drivers/net/wireless/intel/iwlwifi/fw/api/tx.h:
https://lkml.kernel.org/r/20211028192934.01520d7e@canb.auug.org.au
Major changes:
ath11k
* fix QCA6390 A-MSDU handling (CVE-2020-24588)
wcn36xx
* enable hardware scan offload for 5Ghz band
* add missing 5GHz channels 136 and 144
iwlwifi
* support a new ACPI table revision
* improvements in the device selection code
* new hardware support
* support for WiFi 6E enablement via BIOS
* support firmware API version 67
* support for 160MHz in ranging measurements
-----BEGIN PGP SIGNATURE-----
iQFJBAABCgAzFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmF7+wUVHGt2YWxvQGNv
ZGVhdXJvcmEub3JnAAoJEG4XJFUm622bRGoH/0XrfEwzH4iR3j/xRPTBMJjBZO/Z
ZN0PQ2L8402c7iG9M0psSFOdqFe8vtKzuuV367ifQzwmGFoQIzAckL9nCA1yFUBg
EXF3nP0/mb8R0w6rzjkLUQ9EejLLeX35Kh6B1oLgglPdLvE+Yv6/Iqs1yOHwHZFF
RBHqyBc9YcQBuhah4JPqIXr8tUCkRgWwK/VvCwhoGDWimBlH7LhgOHTFQhVJ+Z8b
/RsLS2iIv4wGkiQX9cwilmX3QSz/jK0od1FXHW347v+nm96Fs3d2F1juAyhE6io2
xN1qzEU4SQ90byxhCsBOvZC6JTpRJvw49XME76MrzaLP+FuZ8I2zdAe7wd8=
=Y1xX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2021-10-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.16
Fourth set of patches for v5.16. Mostly fixes this time, wcn36xx and
iwlwifi have some new features but nothing really out of ordinary.
We have one conflict with kspp tree.
Major changes:
ath11k
* fix QCA6390 A-MSDU handling (CVE-2020-24588)
wcn36xx
* enable hardware scan offload for 5Ghz band
* add missing 5GHz channels 136 and 144
iwlwifi
* support a new ACPI table revision
* improvements in the device selection code
* new hardware support
* support for WiFi 6E enablement via BIOS
* support firmware API version 67
* support for 160MHz in ranging measurements
====================
Link: https://lore.kernel.org/r/20211029134707.DE2B0C4360D@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nathan reported that because KASAN_SHADOW_OFFSET was not defined in
Kconfig, it prevents asan-stack from getting disabled with clang even
when CONFIG_KASAN_STACK is disabled: fix this by defining the
corresponding config.
Reported-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Fixes: 8ad8b72721 ("riscv: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
When calling this function, all the shadow memory is already populated
with kasan_early_shadow_pte which has PAGE_KERNEL protection.
kasan_populate_early_shadow write-protects the mapping of the range
of addresses passed in argument in zero_pte_populate, which actually
write-protects all the shadow memory mapping since kasan_early_shadow_pte
is used for all the shadow memory at this point. And then when using
memblock API to populate the shadow memory, the first write access to the
kernel stack triggers a trap. This becomes visible with the next commit
that contains a fix for asan-stack.
We already manually populate all the shadow memory in kasan_early_init
and we write-protect kasan_early_shadow_pte at the end of kasan_init
which makes the calls to kasan_populate_early_shadow superfluous so
we can remove them.
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Fixes: e178d670f2 ("riscv/kasan: add KASAN_VMALLOC support")
Fixes: 8ad8b72721 ("riscv: Add KASAN support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
We can use GPI DMA for devices where it is enabled by firmware. Add
support for this mode
Signed-off-by: Vinod Koul <vkoul@kernel.org>
--
-Changes since v4:
- Fix the kbuild bot warning
-Changes since v3:
- Drop merged spi core, geni patches
- Remove global structs and use local variables instead
- modularize code more as suggested by Doug
- fix kbuild bot warning
drivers/spi/spi-geni-qcom.c | 254 +++++++++++++++++++++++++++++++++---
1 file changed, 239 insertions(+), 15 deletions(-)
Link: https://lore.kernel.org/r/20211020060954.1531783-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In case that there are other components assigned to runtime device,
depending on order dummy component can override their params with its
own, which shouldn't happen. Check if there are any other components
assigned to rtd and if so, skip setting hwparams.
Occurs when using topology where 'snd-soc-dummy' gets assigned by
default as codec and platform component.
Alternative approach would be to copy whole dummy handling and rename it
to "snd-soc-null" or something similar. And remove hwparams assignment
to make it really do nothing.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211015161257.27052-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology needs device for prints and resource allocation. So far,
component->dev is used. However, this may lead to high memory use in
model where card is an independent driver which can be reloaded and
topology is loaded from component's probe() method. Every time machine
driver is reloaded topology is being loaded anew, each time allocating
new memory. Said memory will only be freed when component itself is
being freed.
Address the problem by tying topology to component->card->dev instead,
so memory occupied by the topology is freed whenever related machine
device gets removed.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211015161257.27052-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
soc_tplg_add_dcontrol() passes device as argument which is later used to
print messages. Align it with all other prints in file to use tplg->dev.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211015161257.27052-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add sanity checks to make sure the data is read within file boundary.
Helps in situations where file is only partially copied or malformed.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211015161257.27052-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add sanity check to make sure the data is read within file boundary.
Helps in situations where file is only partially copied or malformed.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211015161257.27052-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If snd_soc_component_set_jack() is called after
snd_soc_component_remove() it may operate on memory which is freed in
->remove handler.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20211015161257.27052-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
INFO: task iou-wrk-6609:6612 blocked for more than 143 seconds.
Not tainted 5.15.0-rc5-syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:iou-wrk-6609 state:D stack:27944 pid: 6612 ppid: 6526 flags:0x00004006
Call Trace:
context_switch kernel/sched/core.c:4940 [inline]
__schedule+0xb44/0x5960 kernel/sched/core.c:6287
schedule+0xd3/0x270 kernel/sched/core.c:6366
schedule_timeout+0x1db/0x2a0 kernel/time/timer.c:1857
do_wait_for_common kernel/sched/completion.c:85 [inline]
__wait_for_common kernel/sched/completion.c:106 [inline]
wait_for_common kernel/sched/completion.c:117 [inline]
wait_for_completion+0x176/0x280 kernel/sched/completion.c:138
io_worker_exit fs/io-wq.c:183 [inline]
io_wqe_worker+0x66d/0xc40 fs/io-wq.c:597
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295
io-wq worker may submit a task_work to the master task and upon
io_worker_exit() wait for the tw to get executed. The problem appears
when the master task is waiting in coredump.c:
468 freezer_do_not_count();
469 wait_for_completion(&core_state->startup);
470 freezer_count();
Apparently having some dependency on children threads getting everything
stuck. Workaround it by cancelling the taks_work callback that causes it
before going into io_worker_exit() waiting.
p.s. probably a better option is to not submit tw elevating the refcount
in the first place, but let's leave this excercise for the future.
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+27d62ee6f256b186883e@syzkaller.appspotmail.com
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/142a716f4ed936feae868959059154362bfa8c19.1635509451.git.asml.silence@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The ring iteration is racy, which isn't necessarily a problem except it
can cause us to iterate the whole thing. That isn't desired or ideal,
and it can lead to excessive runtimes of reading fdinfo.
Cap the iteration at tail - head OR the ring size. While in there, clean
up the ring masking and just dump the raw values along with the masks.
That provides more useful debug info.
Fixes: 83f84356bc ("io_uring: add more uring info to fdinfo for debug")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make sure to use pclose() to properly close the pipe opened by popen().
Fixes: 81f77fd0de ("bpf: add selftest for stackmap with BPF_F_STACK_BUILD_ID")
Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20211026143409.42666-1-andrea.righi@canonical.com
TFA9897 has an internal 'rcv' switch so that it can manage both
loudspeaker and earpiece modes with the same physical speaker.
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Link: https://lore.kernel.org/r/20211024085840.1536438-3-vincent.knecht@mailoo.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are the USB-serial updates for 5.16-rc1, including:
- conversions of usb_control_msg() calls to use the new wrappers where
appropriate
- fix of the keyspan probe error handling after a low-order allocation
failure (e.g. due to fault injection)
- allow hung up ports to be runtime suspended
Included are also some related clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYXuuDwAKCRALxc3C7H1l
CNStAP4ubIEo6iYNF1N9FvkyvIDIlsSF8GOzXpT433cY0jQjxgD+LhzgIbtDi6SI
6Rt91qPdkf+eAsHTLDFjEygigjtinww=
=HGXC
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.16-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.16-rc1
Here are the USB-serial updates for 5.16-rc1, including:
- conversions of usb_control_msg() calls to use the new wrappers where
appropriate
- fix of the keyspan probe error handling after a low-order allocation
failure (e.g. due to fault injection)
- allow hung up ports to be runtime suspended
Included are also some related clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.16-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: keyspan: fix memleak on probe errors
USB: serial: cp210x: use usb_control_msg_recv() and usb_control_msg_send()
USB: serial: ch314: use usb_control_msg_recv()
USB: serial: kl5kusb105: drop line-status helper
USB: serial: kl5kusb105: simplify line-status handling
USB: serial: kl5kusb105: clean up line-status handling
USB: serial: kl5kusb105: use usb_control_msg_recv() and usb_control_msg_send()
USB: serial: keyspan_pda: use usb_control_msg_recv()
USB: serial: ftdi_sio: use usb_control_msg_recv()
USB: serial: f81232: use usb_control_msg_recv() and usb_control_msg_send()
USB: serial: allow hung up ports to be suspended
USB: serial: clean up core error labels
This makes hci_suspend_notifier use the hci_*_sync which can be
executed synchronously which is allowed in the suspend_notifier and
simplifies a lot of the handling since the status of each command can
be checked inline so no other work need to be scheduled thus can be
performed without using of a state machine.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This moves the init stages to use the hci_sync infra and in addition
to that have the stages as function tables so it is easier to change
the command sequence.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mgmt-tester paths:
Set SSP on - Success 2
Set Device ID - SSP off and Power on
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
mgmt-test paths:
Set powered on - Privacy and Advertising
Set Advertising on - Success 2
Set Advertising on - Appearance 1
Set Advertising on - Local name 1
Set Advertising on - Name + Appear 1
Add Advertising - Success 4
Add Advertising - Success 5
Add Ext Advertising - Success 4
Add Ext Advertising - Success 5
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Uses existing *_sync functions
mgmt-test paths:
Read Local OOB Ext Data - Invalid index
Read Local OOB Ext Data - Legacy pairing
Read Local OOB Ext Data - Success SSP
Read Local OOB Ext Data - Success SC
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
New functions:
hci_read_local_oob_data_sync
This function requires all of the data from the cmd cmplt event
to be passed up to the caller via the skb.
mgmt-tester paths:
Read Local OOB Data - Not powered
Read Local OOB Data - Legacy pairing
Read Local OOB Data - Success SSP
Read Local OOB Data - Success SC
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Synchronous version of MGMT_OP_GET_CONN_INFO
Implements:
hci_read_rssi_sync
hci_read_tx_power_sync
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This creates a synchronized Write Fast Connectable call and attaches it
to the MGMT_OP_SET_FAST_CONNECTABLE management opcode.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This make use of hci_cmd_sync_queue when MGMT_SET_POWERED is used so all
commands are run within hdev->cmd_sync_work instead of
hdev->power_on_work and hdev->power_off_work.
In addition to that the power on sequence now takes into account if
local IRK needs to be programmed in the resolving list.
Tested with:
tools/mgmt-tester -s "Set powered"
Test Summary
------------
Set powered on - Success Passed
Set powered on - Invalid parameters 1 Passed
Set powered on - Invalid parameters 2 Passed
Set powered on - Invalid parameters 3 Passed
Set powered on - Invalid index Passed
Set powered on - Privacy and Advertising Passed
Set powered off - Success Passed
Set powered off - Class of Device Passed
Set powered off - Invalid parameters 1 Passed
Set powered off - Invalid parameters 2 Passed
Set powered off - Invalid parameters 3 Passed
Total: 11, Passed: 11 (100.0%), Failed: 0, Not Run: 0
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This replaces the use of hci_update_background_scan with
hci_update_passive_scan which runs from cmd_work_sync and deal properly
with resolving list when LL privacy is enabled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The usage of __hci_cmd_sync() within the hdev->setup() callback allows for
a nice and simple serialized execution of HCI commands. More importantly
it allows for result processing before issueing the next command.
With the current usage of hci_req_run() it is possible to batch up
commands and execute them, but it is impossible to react to their
results or errors.
This is an attempt to generalize the hdev->setup() handling and provide
a simple way of running multiple HCI commands from a single function
context.
There are multiple struct work that are decdicated to certain tasks
already used right now. It is add a lot of bloat to hci_dev struct and
extra handling code. So it might be possible to put all of these behind
a common HCI command infrastructure and just execute the HCI commands
from the same work context in a serialized fashion.
For example updating the white list and resolving list can be done now
without having to know the list size ahead of time. Also preparing for
suspend or resume shouldn't require a state machine anymore. There are
other tasks that should be simplified as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The upper limit of MAX_LP_MSG_LEN on HIP08 is 64K, and the upper limit on
HIP09 is 16K. Regardless of whether it is HIP08 or HIP09, only 16K will be
used. In order to ensure compatibility, it is unified to 16K.
Setting MAX_LP_MSG_LEN to 16K will not cause performance loss on HIP08.
Fixes: fbed9d2be2 ("RDMA/hns: Fix configuration of ack_req_freq in QPC")
Link: https://lore.kernel.org/r/20211029100537.27299-1-liangwenpeng@huawei.com
Signed-off-by: Yixing Liu <liuyixing1@huawei.com>
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
